2002 YAMAHA XVS650A Owners Manual

MOTORCYCLE CARE AND STORAGE
7-2
7


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.


Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments, switch-
es and lights), breather hoses
and vents.


For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
@After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.After riding in the rain, near the sea or
on salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:@ Salt sprayed on roads in the winter may
remain well into spring. @
U5SCE0.book Page 2 Thursday, June 7, 2001 11:24 AM

MOTORCYCLE CARE AND STORAGE
7-3
71. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
CAUTION:@ Do not use warm water since it in-
creases the corrosive action of the
salt. @2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the motorcycle dry completely
before storing or covering it.
EWA00031
WARNING
@

Make sure that there is no oil or
wax on the brakes or tires.


If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
@
ECA00013
CAUTION:@

Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.


Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.


Avoid using abrasive polishing
compounds as they will wear
away the paint.
@NOTE:@ Consult a Yamaha dealer for advice on
what products to use. @
U5SCE0.book Page 3 Thursday, June 7, 2001 11:24 AM

MOTORCYCLE CARE AND STORAGE
7-4
7
Storage Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
ECA00014
CAUTION:@

Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.


To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
@
Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. For motorcycles equipped with a
fuel cock that has an “OFF” posi-
tion: Turn the fuel cock lever to
“OFF”.
3. Drain the carburetor float cham-
bers by loosening the drain bolts;
this will prevent fuel deposits from
building up. Pour the drained fuel
into the fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to pro-
tect the cylinders, piston rings, etc.
from corrosion.
a. Remove the spark plug caps and
spark plugs.
b. Pour a teaspoonful of engine oil
into each spark plug bore.c. Install the spark plug caps onto the
spark plugs, and then place the
spark plugs on the cylinder head
so that the electrodes are ground-
ed. (This will limit sparking during
the next step.)
d. Turn the engine over several times
with the starter. (This will coat the
cylinder walls with oil.)
e. Remove the spark plug caps from
the spark plugs, and then install
the spark plugs and the spark plug
caps.
EWA00003
WARNING
@ To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over. @6. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
U5SCE0.book Page 4 Thursday, June 7, 2001 11:24 AM

MOTORCYCLE CARE AND STORAGE
7-5
77. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover the muffler outlets with plas-
tic bags to prevent moisture from
entering them.
9. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place (less
than 0°C or more than 30°C). For
more information on storing the
battery, see page 6-30.
NOTE:@ Make any necessary repairs before
storing the motorcycle. @U5SCE0.book Page 5 Thursday, June 7, 2001 11:24 AM

SPECIFICATIONS
8
Specifications .................................................................................... 8-1
Conversion table ............................................................................... 8-6
U5SCE0.book Page 1 Thursday, June 7, 2001 11:24 AM

8-1
8
EAU01038
8-SPECIFICATIONSSpecifications CS-01E
Model XVS650/XVS650A
Dimensions
XVS650
Overall length 2,340 mm
Overall width 880 mm
Overall height 1,070 mm
Seat height 695 mm
Wheelbase 1,610 mm
Ground clearance 140 mm
Minimum turning radius 3,100 mm
XVS650A
Overall length 2,450 mm
Overall width 930 mm
Overall height 1,105 mm
Seat height 710 mm
Wheelbase 1,625 mm
Ground clearance 145 mm
Minimum turning radius 3,400 mm
Basic weight (with oil and full
fuel tank)
XVS650233 kg
XVS650A247 kgEngine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement V-type 2-cylinder
Displacement 649 cm
3
Bore × stroke 81 × 63 mm
Compression ratio 9:1
Star ting system Electric star ter
Lubrication system Wet sump
Engine oil
Ty p e
Recommended engine oil
classification API Service SE, SF, SG type or
higher
-20 -10 0
10 20 30
40
50 ˚C
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40
U5SCE0.book Page 1 Thursday, June 7, 2001 11:24 AM

SPECIFICATIONS
8-2
8
Quantity
Without oil filter element
replacement 2.6 L
With oil filter element
replacement 2.8 L
Total amount (dry engine) 3.2 L
Final gear oil
Type Hypoid gear oil SAE 80
(API GL4) or multi-grade hypoid
gear oil SAE 80W-90
Final gear case capacity 0.19 L
Air filterDry type element
Fuel
Type REGULAR UNLEADED
GASOLINE ONLY
Fuel tank capacity 16 L
Reserve amount 3 L
Carburetor
Manufacturer MIKUNI
Model × quantity BDS28 × 2
CAUTION:Be sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled
“ENERGY CONSERVING II”) contain anti-friction additives
which will cause clutch and/or starter clutch slippage, result-
ing in reduced component life and poor engine performance.
Spark plug
Manufacturer/model NGK / DPR7EA-9 or
DENSO / X22EPR-U9
Gap 0.8–0.9 mm
Clutch typeWet, multiple-disc
Transmission
Primary reduction system Spur gear
Primary reduction ratio 1.789
Secondary reduction system Shaft drive
Secondary reduction ratio 3.071
Transmission type Constant-mesh 5-speed
Operation Left foot
Gear ratio 1st 2.714
2nd 1.900
3rd 1.458
4th 1.167
5th 0.967
Chassis
Frame type Double cradle
Caster angle 35°
Tr a i l
XVS650 153 mm
XVS650A 145 mm
U5SCE0.book Page 2 Thursday, June 7, 2001 11:24 AM

SPECIFICATIONS
8-3
8
Tires
XVS650
Front
Type Tube tire
Size 100/90-19 57S
100/90-19 M/C 57S
Manufacturer/model Bridgestone / L309
Dunlop / F24
Rear
Type Tube tire
Size 170/80-15 M/C 77S
Manufacturer/model Bridgestone / G546
Dunlop / K555
Maximum load* 180 kg
Tire air pressure (measured
on cold tires)
Up to 90 kg*
Front 200 kPa (2.00 kgf/cm
2, 2.00 bar)
Rear 225 kPa (2.25 kgf/cm2, 2.25 bar)
90 kg–maximum*
Front 200 kPa (2.00 kgf/cm2, 2.00 bar)
Rear 250 kPa (2.50 kgf/cm2, 2.50 bar)
* Total weight of rider, passenger, cargo and accessoriesXVS650A
Fr o n t
Type Tube tire
Size 130/90-16 67S
130/90-16 M/C 67S
Manufacturer/model Bridgestone / G703
Dunlop / D404F
Rear
Type Tube tire
Size 170/80-15 M/C 77S
Manufacturer/model Bridgestone / G702
Dunlop / D404G
Maximum load* 200 kg
Tire air pressure (measured
on cold tires)
Up to 90 kg*
Front 225 kPa (2.25 kgf/cm
2, 2.25 bar)
Rear 225 kPa (2.25 kgf/cm2, 2.25 bar)
90 kg–maximum*
Front 225 kPa (2.25 kgf/cm2, 2.25 bar)
Rear 250 kPa (2.50 kgf/cm2 , 2.50 bar)
* Total weight of rider, passenger, cargo and accessories
U5SCE0.book Page 3 Thursday, June 7, 2001 11:24 AM