2002 YAMAHA XT500E brake

6-41
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU01008
TroubleshootingTroubleshootingAlthough Yamaha motorcycles
receive a thorough inspection before
shipment from the factory, trouble
may occur during operation. Any
problem in the fuel, compression, or
ignition systems, for example, can
cause poor starting and loss of
power.
The following troubleshooting chart
represents a quick and easy proce-
dure for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it
to a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life
and can lead to expensive repair
bills. Tightening torque:
Axle nut:
105 Nm (10.5 m0kgf)
Brake caliper bracket bolt:
48 Nm (4.8 m0kgf)
Swingarm end bolt:
2.5 Nm (0.25 m0kgf)
4PT-E7 (English) 6/29/01 9:13 AM Page 78

7-2
MOTORCYCLE CARE AND STORAGE
7 8 8
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8 8
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8 8
For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roadsSince sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter
may remain well into spring.1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
4PT-E7 (English) 6/29/01 9:13 AM Page 83

7-3
MOTORCYCLE CARE AND STORAGE
7After cleaning
1. Dry the motorcycle with a
chamois or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally
induced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, includ-
ing chrome- and nickel-plated,
surfaces.
5. Use spray oil as a universal
cleaner to remove any remaining
dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.8. Let the motorcycle dry complete-
ly before storing or covering it.
EWA00001
w8Make sure that there is no oil
or wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent.
8Before operating the motorcy-
cle test its braking perfor-
mance and cornering behav-
ior.
ECA00013
cC8Apply spray oil and wax spar-
ingly and make sure to wipe
off any excess.
8Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
8Avoid using abrasive polish-
ing compounds as they will
wear away the paint.NOTE:
Consult a Yamaha dealer for advice
on what products to use.
4PT-E7 (English) 6/29/01 9:13 AM Page 84

8-3
SPECIFICATIONS
8
Air pressure (cold tire)
up to 90 kg load*
Front 150 kPa (1.50 kgf/cm
2, 1.50 bar)
Rear 150 kPa (1.50 kgf/cm2, 1.50 bar)
90 kg load–Maximum
load*
Front 150 kPa (1.50 kgf/cm2, 1.50 bar)
Rear 225 kPa (2.25 kgf/cm2, 2.25 bar)
Off-road riding
Front 125 kPa (1.25 kgf/cm2, 1.25 bar)
Rear 125 kPa (1.25 kgf/cm2, 1.25 bar)
High speed riding
Front 150 kPa (1.50 kgf/cm2, 1.50 bar)
Rear 225 kPa (2.25 kgf/cm2, 2.25 bar)
* Total weight of rider, passenger, cargo and accessories
Wheels
Front
Type Spoke wheel
Size 21 ×1.85
Rear
Type Spoke wheel
Size 17 ×MT2.50 or
17 M/C ×MT2.50Brakes
Front
Type Single disc brake
Operation Right hand
Fluid DOT 4
Rear
Type Single disc brake
Operation Right foot
Fluid DOT 4
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm (new monocross)
Shock absorber
Front Coil spring/oil damper
Rear Coil spring/gas-oil damper
Wheel travel
Front 225 mm
Rear 200 mm
4PT-E7 (English) 6/29/01 9:13 AM Page 90

8-4
SPECIFICATIONS
8
Electrical
Ignition system T.C.I. (Digital)
Charging system
Type A.C. magneto
Standard output 14 V, 13.5A @ 5,000 rpm
Battery
Type YTX9-BS
Voltage, capacity 12 V, 8 AH
Headlight bulb typeHalogen bulb
Bulb voltage, wattage ×quantity
Headlight 12 V, 60/55W ×1
Tail/brake light 12 V, 5/21W ×1
Auxiliary light 12 V, 4W ×1
12 V, 3.4W ×1 (GB only)
Front flasher light 12 V, 21W ×2
Rear flasher light 12 V, 21W ×2
Meter lighting 12 V, 3.4W ×1
Neutral indicator light 12 V, 3.4W ×1
High beam indicator light 12 V, 3.4W ×1
Turn indicator light 12 V, 3.4W ×1
Fuse20A
4PT-E7 (English) 6/29/01 9:13 AM Page 91

INDEX
E
Engine break-in ..................................... 5-4
Engine idling speed ............................. 6-15
Engine oil and oil filter element ........... 6-10
Engine, starting a warm ......................... 5-2
F
Front and rear brake pads, checking ... 6-22
Front fork, checking ............................. 6-29
Front wheel........................................... 6-37
Installing ............................................ 6-37
Removing .......................................... 6-37
Fuel ....................................................... 3-6
Fuel cock ............................................... 3-8
Fuel consumption, tips for reducing ...... 5-4
Fuel tank cap ......................................... 3-6
Fuse, replacing .................................... 6-32
H
Handlebar switches ............................... 3-3
Light switch ......................................... 3-3
Pass switch ......................................... 3-3
Dimmer switch .................................... 3-3
Turn signal switch ............................... 3-3
Horn switch ......................................... 3-3
Engine stop switch .............................. 3-4
Start switch ......................................... 3-4
Headlight bulb, replacing ..................... 6-33
Helmet holder ...................................... 3-10
I
Identification numbers ........................... 9-1
Ignition circuit cut-off system ............... 3-12
Indicator lights ....................................... 3-2
High beam indicator light .................... 3-2
Neutral indicator light .......................... 3-2
Turn signal indicator light .................... 3-2
K
Key identification number ...................... 9-1
M
Main switch/steering lock ...................... 3-1
Model label ............................................ 9-2
P
Parking .................................................. 5-5
Part locations ......................................... 2-1
Periodic maintenance and lubrication
chart .................................................... 6-3
Pre-operation check list ......................... 4-1
R
Rear brake light switch, adjusting ........ 6-22
Rear suspension, lubricating ............... 6-29
Rear wheel ........................................... 6-39
Removing .......................................... 6-39
Install ................................................ 6-40
S
Seat ....................................................... 3-9
Shift pedal ............................................. 3-5
Shift points (for Switzerland only) .......... 5-3
Shifting .................................................. 5-3
Shock absorber assembly, adjusting ... 3-10
Sidestand ............................................ 3-11
A
Air filter element, cleaning ................... 6-13
B
Battery ................................................. 6-31
Brake and clutch levers, checking and
lubricating ......................................... 6-28
Brake and shift pedals, checking and
lubricating ......................................... 6-28
Brake fluid level, checking ................... 6-23
Brake fluid, changing ........................... 6-24
Brake lever ............................................ 3-5
Brake lever free play, adjusting ........... 6-21
Brake pedal ........................................... 3-5
Brake pedal position, adjusting ........... 6-21
C
Cables, checking and lubricating ......... 6-27
Carburetor, adjusting ........................... 6-14
Care ....................................................... 7-1
Clutch lever ........................................... 3-4
Clutch lever free play, adjusting .......... 6-20
Conversion table ................................... 8-5
Cowling and panels, removing and
installing .............................................. 6-6
D
Drive chain slack ................................. 6-25
Checking ........................................... 6-25
Adjusting ........................................... 6-25
Drive chain, lubricating ........................ 6-26
4PT-E7 (English) 6/29/01 9:13 AM Page 96

Sidestand, checking and lubricating .... 6-28
Spark plug, checking ............................. 6-8
Specifications ........................................ 8-1
Speedometer unit .................................. 3-2
Starter (choke) knob .............................. 3-9
Starting the engine ................................ 5-1
Steering, checking ............................... 6-30
Storage .................................................. 7-4
Supporting the motorcycle ................... 6-36
T
Tachometer ........................................... 3-3
Tail/brake light bulb, replacing ............. 6-35
Throttle cable free play, adjusting ....... 6-16
Throttle grip and cable, checking and
lubricating ......................................... 6-27
Tires .................................................... 6-16
Tool kit ................................................... 6-1
Troubleshooting ................................... 6-41
Troubleshooting chart .......................... 6-42
Turn signal light bulb, replacing ........... 6-35
V
Valve clearance, adjusting .................. 6-16
Vehicle identification number ................ 9-1
W
Wheel bearings, checking ................... 6-30
Wheels ................................................ 6-19
INDEX
4PT-E7 (English) 6/29/01 9:13 AM Page 97