2002 YAMAHA XT500E light

6-34
PERIODIC MAINTENANCE AND MINOR REPAIR
6 4. Remove the headlight bulb hold-
er by turning it counterclockwise,
and then remove the defective
bulb.
EW000119
wHeadlight bulbs get very hot.
Therefore, keep flammable prod-
ucts away from a lit headlight bulb,
and do not touch the bulb until it
has cooled down.
1
1. Headlight bulb holder
6. Install the bulb cover, and then
connect the coupler and leads.
7. Install the headlight unit by
installing the bolts.
8. Install the cowling.
9. Have a Yamaha dealer adjust
the headlight beam if necessary.
5. Place a new bulb into position,
and then secure it with the bulb
holder.
EC000105
cCDo not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be
adversely affected. Thoroughly
clean off any dirt and fingerprints
on the headlight bulb using a cloth
moistened with alcohol or thinner.
a
a. Do not touch this area.
4PT-E7 (English) 6/29/01 9:13 AM Page 71

6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03497
Replacing a turn signal light
bulbTurn signal light bulb, replacing1. Remove the turn signal light lens
by removing the screw.
1
2
1. Screw
2. Lens
EAU01623
Replacing the tail/brake light
bulbTail/brake light bulb, replacing1. Remove the tail/brake light lens
by removing the screws.
21
1. Screw (×2)
2. Lens
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.
ECA00065
cCDo not overtighten the screw, oth-
erwise the lens may break.
1
1. Bulb
4PT-E7 (English) 6/29/01 9:13 AM Page 72

7-2
MOTORCYCLE CARE AND STORAGE
7 8 8
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8 8
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8 8
For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roadsSince sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter
may remain well into spring.1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
4PT-E7 (English) 6/29/01 9:13 AM Page 83

8-4
SPECIFICATIONS
8
Electrical
Ignition system T.C.I. (Digital)
Charging system
Type A.C. magneto
Standard output 14 V, 13.5A @ 5,000 rpm
Battery
Type YTX9-BS
Voltage, capacity 12 V, 8 AH
Headlight bulb typeHalogen bulb
Bulb voltage, wattage ×quantity
Headlight 12 V, 60/55W ×1
Tail/brake light 12 V, 5/21W ×1
Auxiliary light 12 V, 4W ×1
12 V, 3.4W ×1 (GB only)
Front flasher light 12 V, 21W ×2
Rear flasher light 12 V, 21W ×2
Meter lighting 12 V, 3.4W ×1
Neutral indicator light 12 V, 3.4W ×1
High beam indicator light 12 V, 3.4W ×1
Turn indicator light 12 V, 3.4W ×1
Fuse20A
4PT-E7 (English) 6/29/01 9:13 AM Page 91

INDEX
E
Engine break-in ..................................... 5-4
Engine idling speed ............................. 6-15
Engine oil and oil filter element ........... 6-10
Engine, starting a warm ......................... 5-2
F
Front and rear brake pads, checking ... 6-22
Front fork, checking ............................. 6-29
Front wheel........................................... 6-37
Installing ............................................ 6-37
Removing .......................................... 6-37
Fuel ....................................................... 3-6
Fuel cock ............................................... 3-8
Fuel consumption, tips for reducing ...... 5-4
Fuel tank cap ......................................... 3-6
Fuse, replacing .................................... 6-32
H
Handlebar switches ............................... 3-3
Light switch ......................................... 3-3
Pass switch ......................................... 3-3
Dimmer switch .................................... 3-3
Turn signal switch ............................... 3-3
Horn switch ......................................... 3-3
Engine stop switch .............................. 3-4
Start switch ......................................... 3-4
Headlight bulb, replacing ..................... 6-33
Helmet holder ...................................... 3-10
I
Identification numbers ........................... 9-1
Ignition circuit cut-off system ............... 3-12
Indicator lights ....................................... 3-2
High beam indicator light .................... 3-2
Neutral indicator light .......................... 3-2
Turn signal indicator light .................... 3-2
K
Key identification number ...................... 9-1
M
Main switch/steering lock ...................... 3-1
Model label ............................................ 9-2
P
Parking .................................................. 5-5
Part locations ......................................... 2-1
Periodic maintenance and lubrication
chart .................................................... 6-3
Pre-operation check list ......................... 4-1
R
Rear brake light switch, adjusting ........ 6-22
Rear suspension, lubricating ............... 6-29
Rear wheel ........................................... 6-39
Removing .......................................... 6-39
Install ................................................ 6-40
S
Seat ....................................................... 3-9
Shift pedal ............................................. 3-5
Shift points (for Switzerland only) .......... 5-3
Shifting .................................................. 5-3
Shock absorber assembly, adjusting ... 3-10
Sidestand ............................................ 3-11
A
Air filter element, cleaning ................... 6-13
B
Battery ................................................. 6-31
Brake and clutch levers, checking and
lubricating ......................................... 6-28
Brake and shift pedals, checking and
lubricating ......................................... 6-28
Brake fluid level, checking ................... 6-23
Brake fluid, changing ........................... 6-24
Brake lever ............................................ 3-5
Brake lever free play, adjusting ........... 6-21
Brake pedal ........................................... 3-5
Brake pedal position, adjusting ........... 6-21
C
Cables, checking and lubricating ......... 6-27
Carburetor, adjusting ........................... 6-14
Care ....................................................... 7-1
Clutch lever ........................................... 3-4
Clutch lever free play, adjusting .......... 6-20
Conversion table ................................... 8-5
Cowling and panels, removing and
installing .............................................. 6-6
D
Drive chain slack ................................. 6-25
Checking ........................................... 6-25
Adjusting ........................................... 6-25
Drive chain, lubricating ........................ 6-26
4PT-E7 (English) 6/29/01 9:13 AM Page 96

Sidestand, checking and lubricating .... 6-28
Spark plug, checking ............................. 6-8
Specifications ........................................ 8-1
Speedometer unit .................................. 3-2
Starter (choke) knob .............................. 3-9
Starting the engine ................................ 5-1
Steering, checking ............................... 6-30
Storage .................................................. 7-4
Supporting the motorcycle ................... 6-36
T
Tachometer ........................................... 3-3
Tail/brake light bulb, replacing ............. 6-35
Throttle cable free play, adjusting ....... 6-16
Throttle grip and cable, checking and
lubricating ......................................... 6-27
Tires .................................................... 6-16
Tool kit ................................................... 6-1
Troubleshooting ................................... 6-41
Troubleshooting chart .......................... 6-42
Turn signal light bulb, replacing ........... 6-35
V
Valve clearance, adjusting .................. 6-16
Vehicle identification number ................ 9-1
W
Wheel bearings, checking ................... 6-30
Wheels ................................................ 6-19
INDEX
4PT-E7 (English) 6/29/01 9:13 AM Page 97