2002 YAMAHA WR 250F light

SPEC

2 - 3
GENERAL SPECIFICATIONS
Tire:
Type With tube
Size (front) 80/100-21 51M (For USA, CDN and ZA)
90/90-21 54R (For EUROPE, AUS and NZ)
Size (rear) 100/100-18 59M (For USA, CDN and ZA)
130/90-18 69R (For EUROPE, AUS and NZ)
Tire pressure (front and rear) 100 kPa (1.0 kgf/cm
2

, 15 psi)
Brake:
Front brake type Single disc brake
Operation Right hand operation
Rear brake type Single disc brake
Operation Right foot operation
Suspension:
Front suspension Telescopic fork
Rear suspension Swingarm (link type monocross suspension)
Shock absorber:
Front shock absorber Coil spring/oil damper
Rear shock absorber Coil spring/gas, oil damper
Wheel travel:
Front wheel travel 300 mm (11.8 in)
Rear wheel travel 315 mm (12.4 in)
Electrical:
Ignition system CDI magneto
Headlight type: Quartz bulb (halogen)
Bulb wattage
×
quantity:
Headlight 12 V 60/55 W
×
1
Taillight 12 V 21/5 W
×
1

SPEC
2 - 14
MAINTENANCE SPECIFICATIONS
NOTE:
1. First, tighten the steering nut approximately 38 Nm (3.8 m • kg, 27 ft • lb) by using the steering
nut wrench, then loosen the steering nut one turn.
2. Retighten the steering nut 7 Nm (0.7 m • kg, 5.1 ft • lb). Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Upper bracket and outer tube M8 × 1.25 4 23 2.3 17
Lower bracket and outer tube M8 × 1.25 4 20 2.0 14
Upper bracket and steering stem M24 × 1.0 1 145 14.5 105
Handlebar holder and upper bracket M8 × 1.25 4 28 2.8 20
Steering stem and steering ring nut M28 × 1.0 1 Refer to NOTE.
Front fork and front fork cap bolt M48 × 1.0 2 30 3.0 22
Front fork and base valve M30 × 1.0 2 55 5.5 40
Front fork cap bolt and damper rod M12 × 1.25 2 29 2.9 21
Front fork bleed screw and front fork cap bolt M5 × 0.8 2 1 0.1 0.7
Front fork and front fork protector M6 × 1.0 6 10 1.0 7.2
Meter cable holder and front fork protector M5 × 0.8 2 4 0.4 2.9
Front fork and brake hose guide M5 × 0.8 2 4 0.4 2.9
Front fork and brake hose holder M6 × 1.0 2 10 1.0 7.2
Front fork and brake hose cover (M8) M8 × 1.25 1 16 1.6 11
(M6) M6 × 1.0 1 7 0.7 5.1
Throttle grip cap M5 × 0.8 2 4 0.4 2.9
Front brake master cylinder M6 × 1.0 2 9 0.9 6.5
Brake lever mounting bolt M6 × 1.0 1 6 0.6 4.3
Brake lever mounting nut M6 × 1.0 1 6 0.6 4.3
Brake lever position locknut M6 × 1.0 1 5 0.5 3.6
Front brake hose guide M5 × 0.8 2 4 0.4 2.9
Clutch lever holder M5 × 0.8 2 4 0.4 2.9
Clutch lever mounting bolt M6 × 1.0 1 2 0.2 1.4
Decompression lever holder M5 × 0.8 2 4 0.4 2.9
Light switch M4 × 0.7 2 2 0.2 1.4
Front brake master cylinder cap M4 × 0.7 2 2 0.2 1.4
Front brake hose union bolt M10 × 1.25 2 30 3.0 22
Front brake caliper M8 × 1.25 2 23 2.3 17
Pad pin plug M10 × 1.0 2 3 0.3 2.2
Front brake caliper and pad pin M10 × 1.0 1 18 1.8 13
Rear brake caliper and pad pin M10 × 1.0 1 18 1.8 13
Brake caliper and bleed screw M8 × 1.25 2 6 0.6 4.3
Front wheel axle and axle nut M16 × 1.5 1 105 10.5 75
Front wheel axle holder M8 × 1.25 4 23 2.3 17
Front brake disc M6 × 1.0 6 12 1.2 8.7

SPEC
2 - 16
MAINTENANCE SPECIFICATIONS
NOTE:
- marked portion shall be checked for torque tightening after break-in or before each race. Headlight stay (lower) and lower bracket M8 × 1.25 2 7 0.7 5.1
Headlight (left and right) M6 × 1.0 2 10 1.0 7.2
Headlight (lower) M6 × 1.0 1 7 0.7 5.1
Taillight M6 × 1.0 3 4 0.4 2.9
Taillight lead clamp and rear fender M4 × 1.59 2 1 0.1 0.7
Coolant reservoir (front) M6 × 1.0 1 7 0.7 5.1
Coolant reservoir (rear) M6 × 1.0 1 11 1.1 8.0
Sidestand bracket and frame M10 × 1.25 2 66 6.6 48
Sidestand M10 × 1.25 1 64 6.4 46 Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb

SPEC
2 - 17
MAINTENANCE SPECIFICATIONS
EC212300
ELECTRICAL
Item Standard Limit
Ignition system:
Advancer type Electrical ----
CDI:
Magneto-model (stator)/manufac-
turer5NG-50/YAMAHA----
Charging coil 1 resistance (color) 640 ~ 960 Ω at 20 ˚C (68 ˚F)
(Green – Brown)----
Charging coil 2 resistance (color) 464 ~ 696 Ω at 20 ˚C (68 ˚F)
(Green – Pink)----
Lighting coil resistance (color) 0.16 ~ 0.24 Ω at 20 ˚C (68 ˚F)
(Black – Yellow)----
Pickup coil resistance (color) 248 ~ 372 Ω at 20 ˚C (68 ˚F)
(White – Red)----
CDI unit-model/manufacturer 5PH-50/YAMAHA
(For USA)
5PH-60/YAMAHA
(For EUROPE)
5PH-80/YAMAHA
(For CDN, AUS, NZ and ZA)----
----
----
Ignition coil:
Model/manufacturer 4SR-00/YAMAHA ----
Minimum spark gap 6 mm (0.24 in) ----
Primary coil resistance 0.20 ~ 0.30 Ω at 20 ˚C (68 ˚F) ----
Secondary coil resistance 9.5 ~ 14.3 kΩ at 20 ˚C (68 ˚F) ----
Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Stator M6 × 1.0 3 10 1.0 7.2
Rotor M10 × 1.25 1 48 4.8 35
Neutral switch M5 × 0.8 2 4 0.4 2.9
Ignition coil M6 × 1.0 2 7 0.7 5.1

2 - 19
SPEC

CABLE ROUTING DIAGRAM
EC240000
CABLE ROUTING DIAGRAM
1
Hose guide
2
Brake hose
3
Voltage regulator
4
Light switch lead
5
Fuel tank breather hose
6
Engine stop switch lead
7
Clamp
8
Oil tank breather hose
9
Sub-wire harness
0
Taillight lead
A
Throttle position sensor lead
B
Neutral switch lead
C
Oil hose
D
Cylinder head breather hose
E
CDI magneto lead
F
Clutch cable
G
Cable guide
H
Carburetor breather hose
I
Carburetor overflow hose
J
Coolant reservoir breather hose
K
Decompression cable
L
Ground lead
M
Ignition coil lead
N
CDI unit lead
O
Voltage regulator lead
Å
Pass the fuel tank breather hose
behind handlebar, then insert it
into the steering stem hole.
ı
Pass the decompression cable,
engine stop switch lead and light
switch lead under where the oil
hose is attached.
Ç
Pass the voltage regulator lead,
engine stop switch lead and light
switch lead over the radiator
hose.
Î
Fasten the engine stop switch
lead, light switch lead and igni-
tion coil lead of the sub-wire har-
ness.
‰
Fasten the sub-wire harness
and engine stop switch lead.
Ï
Pass the cylinder head breather
hose along the right side of the
oil tank breather hose.
Ì
Fasten the sub-wire harness
and light switch lead in front of
the upper engine brackets.
Ó
Fasten the sub-wire harness.
È
Pass the sub-wire harness
between the upper engine
brackets.
Ô
Fasten the sub-wire harness.

Fasten the throttle position sen-
sor lead.

2 - 20
SPEC

CABLE ROUTING DIAGRAM
Ò
Make sure that the throttle
position sensor lead coupler
does not go outside the chas-
sis.
˜
Pass the carburetor breather
hoses and overflow hose
between the connecting rod
and cross tube (frame).
ˆ
Fasten the neutral switch lead
on the oil hose with a plastic
locking tie and cut off the tie
end.
Ø
Pass the cylinder head
breather hose through the hose
guide.
∏
Pass the clutch cable through
the cable guide.
Œ
Fasten the neutral switch lead
and CDI magneto lead.
Â
Pass the clutch cable along the
inner side of the cylinder head
breather hose.
Í
Pass the cylinder head
breather hose along the inner
side of the radiator hose.
Ê
Pass the clutch cable in front of
the radiator mounting boss.
Ë
Fit the brake hose into the
guides on the protector.
◊
Pass the neutral switch lead
and CDI magneto lead through
the cable guide.
„
Fasten the ground lead
together with the ignition coil
lead.
Ù
Do not allow the light switch
lead to slacken between the
two clamps.
Á
Pass the decompression cable
along the right side of the cylin-
der head breather hose.
Û
Pass the clutch cable through
the cable guides.
Pass the carburetor breather
hoses, overflow hose and
coolant reservoir breather
hose so that all there hoses
do not contact the rear shock
absorber.
Position each lead at the
lower left of the main tube
(frame).
AA
AB

2 - 22
SPEC
1Coolant reservoir hose
2Coolant reservoir breather hose
3Clamp
4Taillight lead
5Hose guideÅFasten the coolant reservoir hose and coolant
reservoir breather hose.
ıDo not allow the taillight lead to slacken.
ÇPass the coolant reservoir hose and coolant res-
ervoir breather hose through the hose guide.
CABLE ROUTING DIAGRAM

2 - 23
SPECCABLE ROUTING DIAGRAM
1Brake hose
2Brake hose holder
3Brake master cylinderÅInstall the brake hose to the brake caliper with the
paint on the pipe facing the brake caliper and with
the pipe contacting the brake caliper projection.
ıPass the brake hose into the brake hose holders.
ÇIf the brake hose contacts the spring (rear shock
absorber), correct its twist.
ÎInstall the brake hose so that its pipe portion
directs as shown and lightly touches the projection
on the brake master cylinder.
A 2
3
1ÎÇ
ı
A
12
3Å