2002 YAMAHA BT1100 drain bolt

EAU00462
1. Engine oil filler cap
PERIODIC MAINTENANCE AND MINOR REPAIR
1
NOTE:
Make sure that the motorcycle is posi-
tioned straight up when checking the oil
level. A slight tilt to the side can result in a
false reading.
2. Start the engine, warm it up for sever-
al minutes, and then turn it off.
3. Wait a few minutes until the oil set-
tles, and then check the oil level
through the check window located at
the bottom-left side of the crankcase.
NOTE:
The engine oil should be between the min-
imum and maximum level marks.
4. If the engine oil is below the minimum
level mark, add sufficient oil of the
recommended type to raise it to the
correct level.To change the engine oil without oil
filter element replacement
1. Start the engine, warm it up for sever-
al minutes, and then turn it off.
2. Place an oil pan under the engine to
collect the used oil.
3. Remove the engine oil filler cap and
drain bolt to drain the oil from the
crankcase.
6-7
6
2
31
EAU01712
Engine oil and oil filter element
The engine oil level should be checked be-
fore each ride. In addition, the oil must be
changed and the oil filter element replaced
at the intervals specified in the periodic
maintenance and lubrication chart.
To check the engine oil level
1. Place the motorcycle on a level sur-
face and hold it in an upright position.
1. Engine oil level window
2. Maximum level mark
3. Minimum level mark

EAU00462PERIODIC MAINTENANCE AND MINOR REPAIR
EC000072
•In order to prevent clutch slippage
(since the engine oil also lubri-
cates the clutch), do not mix any
chemical additives with the oil or
use oils of a higher grade than
“CD”. In addition, do not use oils
labeled "ENERGY CONSERVING II"
or higher.
•Make sure that no foreign material
enters the crankcase.
CAUTION:6. Start the engine, and then let it idle for
several minutes while checking it for
oil leakage. If oil is leaking, immedi-
ately turn the engine off and check for
the cause.
NOTE:
After the engine is started, the engine oil
level warning light should go off if the oil
level is sufficient.
EC000067
If the oil level warning light flickers or
remains on, immediately turn the
engine off and have a Yamaha dealer
check the vehicle.
7. Turn the engine off, and then check
the oil level and correct it if neces-
sary.
NOTE:
Have a Yamaha dealer replace the oil filter
element when necessary.
CAUTION:
1. Engine oil drain bolt
6-8
6
1
4. Install the engine oil drain bolt, and
then tighten it to the specified torque.
5. Add the specified amount of the rec-
ommended engine oil, and then in-
stall and tighten the oil filler cap. Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kgf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter element
replacement:
3.0 L
With oil filter element
replacement:
3.1 L
Total amount (dry engine):
3.6 L

EAU00462PERIODIC MAINTENANCE AND MINOR REPAIR
3
1 2
To check the final gear oil level
1. Place the motorcycle on a level sur-
face and hold it in an upright position.
NOTE:
•The final gear oil level must be
checked on a cold engine.
•Make sure that the motorcycle is posi-
tioned straight up when checking the
oil level. A slight tilt to the side can
result in a false reading.2. Remove the oil filler bolt, and then
check the oil level in the final gear
case.
NOTE:
The oil level should be at the brim of the
filler hole.
3. If the oil is below the brim of the filler
hole, add sufficient oil of the recom-
mended type to raise it to the correct
level.
To change the final gear oil
1. Place an oil pan under the final gear
case to collect the used oil.
2. Remove the oil filler bolt and drain
bolt to drain the oil from the final gear
case.
6-9
6
1. Final gear oil drain bolt
2. Final gear oil filler bolt
3. Oil level
EAU04083
Final gear oil
The final gear case must be checked for oil
leakage before each ride. If any leakage is
found, have a Yamaha dealer check and
repair the motorcycle. In addition, the final
gear oil level must be checked and the oil
changed as follows at the intervals speci-
fied in the periodic maintenance and lubri-
cation chart.
EW000066WARNING0
•Make sure that no foreign material
enters the final gear case.
• Make sure that no oil gets on the
tire or wheel.

EAU00462PERIODIC MAINTENANCE AND MINOR REPAIR
2 1
6. Check the final gear case for oil leak-
age. If oil is leaking, check for the
cause.
EAUB0008
Cleaning the air filter element
The air filter element should be cleaned at
the intervals specified in the periodic main-
tenance and lubrication chart. Clean the
air filter element more frequently if you are
riding in unusually wet or dusty areas. 4. Add the recommended final gear oil
to the brim of the filler hole.
NOTE:
GL4 is a quality rating. Hypoid gear oils
rated GL5 or GL6 may also be used.
5. Install and tighten the oil filler bolt.1. Remove the seat. (See page 3-13 for
seat removal and installation proce-
dures).
2. Remove panels 1 and 2. (See page
6-5 for panel removal and installation
procedures).
3. Remove the fuel tank bolts.
6-10
6
Tightening torque:
Final gear oil drain bolt:
23 Nm (2.3 m·kgf)
Recommended final gear oil:
Hypoid gear oil SAE 80 (API GL4)
or multi-grade hypoid gear oil
SAE 80W-90
Oil quantity:
0.2 L
3. Install the final gear oil drain bolt, and
then tighten it to the specified torque.
1. Fuel tank right bolt (x 2)
2. Fuel tank left bolt (x 2)


1. Left panel
2. Right panel

MOTORCYCLE CARE AND STORAGE
Storage
Short-term
Always store your motorcycle in a cool, dry
place and, if necessary, protect it against
dust with a porous cover.
ECA00014
•Storing the motorcycle in a poorly
ventilated room or covering it with
a tarp, while it is still wet, will allow
water and humidity to seep in and
cause rust.
•To prevent corrosion, avoid damp
cellars, stables (because of the
presence of ammonia) and areas
where strong chemicals are
stored.
CAUTION:Long-term
Before storing your motorcycle for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. For motorcycles equipped with a fuel
cock that has an “OFF” position: Turn
the fuel cock lever to “OFF”.
3. Drain the carburetor float chambers
by loosening the drain bolts; this will
prevent fuel deposits from building
up. Pour the drained fuel into the fuel
tank.
4. Fill up the fuel tank and add fuel sta-
bilizer (if available) to prevent the fuel
tank from rusting and the fuel from
deteriorating.
5. Perform the following steps to protect
the cylinders, piston rings, etc. from
corrosion.a. Remove the spark plug caps and
spark plugs.
b. Pour a teaspoonful of engine oil into
each spark plug bore.
c. Install the spark plug caps onto the
spark plugs, and then place the spark
plugs on the cylinder head so that the
electrodes are grounded. (This will
limit sparking during the next step).
d. Turn the engine over several times
with the starter. (This will coat the
cylinder walls with oil).
e. Remove the spark plug caps from the
spark plugs, and then install the spark
plugs and the spark plug caps.
EWA00003WARNING0
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning the
engine over.
7-4
7
EAU03412