2002 TOYOTA 4RUNNER lock

’02 4Runner_U (L/O 0108)
2542002 MY 4RUNNER_U (OM 35787U)
INSIDE THE VEHICLE
Items listed below should be checked
regularly, e.g. while performing periodic
services, cleaning the vehicle, etc.
Lights
Make sure the headlights, stop lights, tail
lights, turn signal lights, and other lights
are all working. Check headlight aim.
Service reminder indicators and warning
buzzers
Check that all service reminder indicators
and warning buzzers function properly.
Steering wheel
Check that it has the specified free play.
Be alert for changes in steering condition,
such as hard steering or strange noise.
Seats
Check that all seat controls such as seat
adjusters, seatback recliner, etc. operate
smoothly and that all latches lock securely
in any position. Check that the head re-
straint move up and down smoothly and
that the locks hold securely in any latched
position. For foldingdown rear seatbacks
and swingup rear seat cushions, check
that the latches lock securely. Seat belts
Check that the seat belt system such as
buckles, retractors and anchors operate
properly and smoothly. Make sure the belt
webbing is not cut, frayed, worn or dam-
aged.
Accelerator pedal
Check the pedal for smooth operation and
uneven pedal effort or catching.
Brake pedal
Check the pedal for smooth operation and
that the pedal has the proper clearance.
Check the brake booster function.
Brakes
At a safe place, check that the brakes do
not pull to one side when applied.
Parking brake
Check that the lever has the proper travel
and that, on a safe incline, your vehicle
is held securely with only the parking
brake applied.
Automatic transmission “Park” mecha-
nism
Check the lock release button of the se-
lector lever for proper and smooth opera-
tion. On a safe incline, check that your
vehicle is held securely with the selector
lever in “P” position and all brakes re-
leased.
IN THE ENGINE COMPARTMENT
Items listed below should be checked
from time to time, e.g. each time when
refueling.
Washer fluid
Make sure there is sufficient fluid in the
tank. See Section 73 for additional in-
formation.
Engine coolant level
Make sure the coolant level is between
the “F” and “L” lines on the seethrough
reservoir when the engine is cold. See
Section 72 for additional information.
Radiator, condenser and hoses
Check that the front of the radiator and
condenser are clean and not blocked with
leaves, dirt, or insects. See Section 72
for additional information.

’02 4Runner_U (L/O 0108)
2582002 MY 4RUNNER_U (OM 35787U)
1. Windshield and back window washer
fluid tank
2. Power steering fluid reservoir
3. Engine oil level dipstick
4. Engine oil filler cap
5. Brake fluid reservoir
6. Fuse block
7. Battery
8. Engine coolant reservoir
9. Radiator
10. Condenser
Engine compartment overview

’02 4Runner_U (L/O 0108)
2682002 MY 4RUNNER_U (OM 35787U)
If cold add
If cold O.K.
If hot add If hot O.K.
Check the fluid level on the dipstick. If
necessary, add automatic transmission
fluid DEXRON II or III.
If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little
more in frigid temperatures), the fluid is
hot (60 C—80 C or 140 F—175 F). You
may also check the level when the fluid
is cold (about room temperature,
10 C—30 C or 50 F—85 F) if the engine
has not been run for about five hours.
a. Clean all dirt from outside of the reser-
voir tank.
b. Remove the reservoir cap by turning it
counterclockwise and wipe the dipstick
clean. c. Reinstall the reservoir cap.
d. Remove the reservoir cap again and
look at the fluid level. If the fluid is cold,
the level should be in the “COLD” range
on the dipstick. Similarly, if it is hot, the
fluid level should be in the “HOT” range.
If the level is at the low side of either
range, add automatic transmission fluid
DEXRON
II or III to bring the level within
the range.
e. After replacing the reservoir cap, visu-
ally check the steering box case, vane
pump and hose connections for leaks or
damage.
CAUTION
The reservoir tank may be hot so be
careful not to burn yourself.
NOTICE
Avoid overfilling, or the power steer-
ing could be damaged.
Keep your tire pressures at the proper
level.
The recommended cold tire pressures, tire
size and the vehicle capacity weight are
given in Section 8. The recommended tire
pressures and tire size are also on the
tire pressure label as shown.
You should check the tire pressures every
two weeks, or at least once a month. And
do not forget the spare!
Checking power steering fluid Checking tire pressure

’02 4Runner_U (L/O 0108)
2722002 MY 4RUNNER_U (OM 35787U)
CAUTION
Do not drive with the snow tires
incorrectly inflated.
Never drive over 120 km/h (75 mph)
with any type of snow tires.
TIRE CHAIN SELECTION
Use the tire chains of correct size.
Regulations regarding the use of tire
chains vary according to location or
type of road, so always check them
before installing chains.
CHAIN INSTALLATION
Install the chains on the rear tires as
tightly as possible. Do not use tire
chains on the front tires. Retighten
chains after driving 0.5—1.0 km
(1/4—1/2 mile).
When installing chains on your tires, care-
fully follow the instructions of the chain
manufacturer.
If wheel covers are used, they will be
scratched by the chain band, so remove
the covers before putting on the chains.
CAUTION
Do not exceed 50 km/h (30 mph) or
the chain manufacturer ’s recom-
mended speed limit, whichever is
lower.
Drive carefully avoiding bumps,
holes, and sharp turns, which may
cause the vehicle to bounce.
Avoid sharp turns or lockedwheel
braking, as use of chains may ad-
versely affect vehicle handling.
When driving with chains installed,
be sure to drive carefully. Slow
down before entering the curves to
avoid losing control of the vehicle.
Otherwise an accident may occur.
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.
If you fail to replace damaged wheels, the
tire may slip off the wheel or cause loss
of handling control.
WHEEL SELECTION
When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.
Correct replacement wheels are available
at your Toyota dealer.
A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ab ility, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis.
Replacing wheels

’02 4Runner_U (L/O 0108)
2902002 MY 4RUNNER_U (OM 35787U)
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.):
With rear heater 9.0 (9.5, 7.9)
Without rear heater 8.0 (8.5, 7.0)
Coolant type:
“TOYOTA Long Life Coolant” or equiva-
lent
With ethyleneglycol type coolant for a
proper corrosion protection of aluminum
components
Do not use alcohol type antifreeze or
plain water alone.
BATTERY
Open voltage
∗ at 20 C (68 F):
12.6—12.8 V Fully charged
12.2—12.4 V Half charged
11.8—12.0 V Discharged
∗: Voltage that is checked 20 minutes af- ter the key is removed with all the
lights turned off
Charging rates: 5 A max. AUTOMATIC TRANSMISSION
Fluid capacity (drain and ref
ill),
L (qt., Imp. qt.):
Twowheel drive modelsUp to 1.6 (1.7, 1.4)
Fourwheel drive models Up to 2.0 (2.1, 1.8)
Fluid type: Automatic transmission fluid DII or
DEXRON III (DEXRON II)
TRANSFER
Oil capacity, L (qt., Imp. qt.): 1.2 (1.3, 1.1)
Oil type: Gear oil API GL4 or GL5
Recommended oil viscosity: SAE 75W90 DIFFERENTIAL
Oil capacity, L (qt., Imp. qt.):
Twowheel drive models2.75 (2.9, 2.4)
Fourwheel drive models Front1.15 (1.2, 1.0)
Rear
With center differential lock system2.75 (2.9, 2.4)
Without center differential lock sys-
tem 2.45 (2.6, 2.2)
Oil type: Hypoid gear oil API GL5
Recommended oil viscosity:
FrontSAE 75W90
Rear Above 18 C (0 F)
SAE 90
Below 18 C (0 F)
SAE 80W or 80W90

’02 4Runner_U (L/O 0108)
2922002 MY 4RUNNER_U (OM 35787U)
Engine compartment
(without daytime running light system)
Fuses (type A)
1. ALTS 7.5 A: Charging system
2. PWR OUTLET 15 A: Power outlets
3. RR HTR 10 A: Rear air conditioning
system
4. MPXB 15 A: Power back window,
back door lock, back window wiper,
open door warning (back door), power
door lock control system, back window
defogger, horns, theft deterrent system
Tires
Tire size Tire pressure
kPa (kgf/cm
2 or bar, psi)
Front Rear
P265/70R16 111S
P225/75R15 102S 220 (2.2, 32) 220 (2.2, 32)
200 (2.0, 29) 200 (2.0, 29) Wheel size
7J 16
∗
1
7JJ 16∗
2
7J 15∗
1
7JJ 15∗
2
∗ 1
: Vehicles with steel wheels∗2: Vehicles with aluminum wheels
NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire pressure” through “Aluminum wheel precautions”
in Section 72.
Wheel nut torque, N⋅ m (kgf⋅m, ft ⋅lbf):
11 0 ( 11 . 5 , 8 3 )
Tire size, pressure and wheel size:
Fuses

’02 4Runner_U (L/O 0108)
2932002 MY 4RUNNER_U (OM 35787U)
Engine compartment
(with daytime running light system)
5. DOME 15 A: Interior lights, personal
lights, luggage compartment light,
clock, car audio system, gauges and
meters, ignition switch light, vanity mir-
ror light, daytime running light
6. OBD 7.5 A: Onboard diagnosis sys-
tem
7. EFI 20 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system
8. HEAD(RH) 10 A: Righthand headlight,
gauges and meters
9. HEAD(LH) 10 A: Lefthand headlight
Instrument panel
10. TAIL 10 A: Tail lights, license plate
lights, instrument panel lights
11. A.C 10 A: Air conditioning system
12. MIR HTR 10 A: Outside rear view mir-
ror heaters
13. DEFOG 15 A: Back window defogger
14. ETCS 15 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system
15. DRL 7.5 A: Daytime running light sys-
tem
16. HEAD (HI RH) 10 A: Righthand head- light (high beam), gauges and meters 17. HEAD (HI LH) 10 A: Lefthand head-
light (high beam)
18. HEAD (LO RH) 10 A: Righthand
headlight (low beam)
19. HEAD (LO LH) 10 A: Lefthand head-
light (low beam)
20. TOWING 25 A: Trailer lights (backup
lights, rear turn signal lights, stop/tail
lights)
21. SEAT HTR 20 A: Seat heater
22. FOG 15 A: Front fog lights
23. ECUIG 10 A: Cruise control system,
antilock brake system, vehicle skid
control system, SRS airbag system,
electronically controlled automatic
transmission system, power antenna,
power window, electric moon roof, pow-
er back window, back window defogger,
back window wiper
24. TURN 10 A: Turn signals lights, emer-
gency flashers
25. WIPER 25 A: Windshield wipers and
washer, power door lock control sys-
tem, back window defogger, horns,
theft deterrent system
26. 4WD 20 A: A.D.D. control system,
fourwheel drive control system, center
differential lock system

’02 4Runner_U (L/O 0108)
2942002 MY 4RUNNER_U (OM 35787U)
27. ACC 15 A: Car audio system, power
antenna, clock, power rear view mirror
control, cigarette lighter, seat belt pre-
tensioners, electronically controlled au-
tomatic transmission system, power
outlets, theft deterrent system
28. GAUGE 10 A: Gauges and meters,
back window defogger, daytime running
light system, air conditioning system,
cruise control system, center differen-
tial lock system, electronically con-
trolled automatic transmission, backup
lights
29. IGN 10 A: SRS airbag system, seat
belt pretensioners, multiport fuel injec-
tion system/sequential multiport fuel in-
jection system, discharge warning light,
vehicle skid control system
30. ECUB 7.5 A: Gauges and meters, air
conditioning system
31. HORN,HAZ 15 A: Horns, emergency
flashers
32. STA 7.5 A: Starting system
33. STOP 10 A: Stop lights, highmounted
stoplight Fuses (type B)
34. HEATER 50 A: Air conditioning system,
all components in “A.C” fuse
35. AM1 40 A: Starting system, all compo-
nents in “ACC”, “GAUGE”, “TURN”,
“ECUIG”, “WIPER” and “4WD” fuses
36. J/B 50 A: All components in “POWER”,
“HORN,HAZ”, “STOP” and “ECUB”
fuses
37. AM2 30 A: Starting system, multiport
fuel injection system/sequential multi-
port fuel injection system, all compo-
nents in “STA” and “IGN” fuses
38. ABS2 40 A: Antilock brake system,
active traction control system, vehicle
skid control system
39. POWER 30 A: Power window, power
back window, electric moon roof, power
seat, back door lock
Fuses (type C)
40. ABS 60 A: Antilock brake system
41. ALT 120 A: Charging system, all com-
ponents in “AM1”, “HEATER”, “TAIL”,
“RR HTR”, “ALTS”, “DEFOG”, “MIR
HTR” and “ACC” fuses