YH4
GRAND
VITARA
1
1. Clutch pedal free travel
MAINTENANCE AND LUBRICATION 0B-15
CHASSIS AND BODY
ITEM 6-1
Clutch
Pedal inspection
Check clutch pedal for height and free travel referring to Section
7C1. Adjust or correct if necessary.
Fluid inspection
1) Check around master cylinder and reservoir for fluid leakage.
If found leaky, correct.
2) Check fluid level.
If fluid level is lower than the minimum level of reservoir, refilling
is necessary. Fill reservoir with specified brake fluid indicated on
clutch reservoir cap.
For the details, refer to On-vehicle service in Section 7C1.
CAUTION:
Since clutch system of this vehicle is factory-filled with
glycol-base brake fluid, do not use or mix different type
of fluid when refilling system; otherwise serious damage
will occur. Do not use old or used brake fluid, or one taken
from unsealed container.
ITEM 6-2
Brake Discs, Pads, Brake Drums and Shoes Inspection
[Brake discs and pads]
1) Remove wheel and caliper but don't disconnect brake hose from
caliper.
2) Check front disc brake pads and discs for excessive wear, dam-
age and deflection. Replace parts as necessary. For details, re-
fer to Section 5B.
Be sure to torque caliper pin bolts to specification.
[Brake drums and shoes]
1) Remove wheel and brake drum.
2) Check rear brake drums and brake linings for excessive wear
and damage, while wheels and drums are removed. At the same
time, check wheel cylinders for leaks. Replace these parts as
necessary.
For details, refer to Section 5C.
YH4
GRAND
VITARA
3-4 STEERING, SUSPENSION, WHEELS AND TIRES
ConditionPossible CauseCorrection
Wander or Poor
Steering StabilityMismatched or uneven tires.
Loose ball joints and tie rod
ends.
Faulty shock absorbers / struts or
mounting.
Loose stabilizer bar.
Broken or sagging springs.
Rack and pinion not properly adjusted.
(if equipped with manual steering
gear case)
Disturbed front end alignment.Replace tire or inflate tires to
proper pressure.
Replace suspension control arm or
tie rod end.
Replace absorber / strut or repair
mounting.
Tighten or replace stabilizer bar or
bushes.
Replace spring.
Check or adjust rack and pinion
torque.
Check and adjust front end alignment.
Erratic Steering when
BrakingWorn wheel bearings.
Broken or sagging springs.
Leaking wheel cylinder or caliper.
Warped discs.
Badly worn brake linings.
Drum is out of round in some brakes.
Wheel tires are inflated unequally.
Defective wheel cylinders.
Disturbed front end alignment.Replace wheel bearing.
Replace spring.
Repair or replace wheel cylinder or
caliper.
Replace brake disc.
Replace brake shoe lining.
Replace brake drum.
Inflate tires to proper pressure.
Replace or repair wheel cylinder.
Check front end alignment.
Low or Uneven Trim
Height
Right-to-left trim height
(H) difference should be
within 15 mm (0.6 in.)
with curb weight.
*Same with rear side.Broken or sagging springs.
Overloaded.
Incorrect springs.Replace spring.
Check loading.
Replace spring.
Ride Too SoftFaulty shock absorber or struts.Replace shock absorber or strut.
Suspension BottomsOverloaded.
Faulty shocks or struts.
Incorrect broken or sagging springs.Check loading.
Replace shock absorber or strut.
Replace spring.
YH4
GRAND
VITARA
3D-8 FRONT SUSPENSION
1. Circlip
2. Washer
1. Wire
1. Front wheel
speed sensor
2. Harness clamp bolt
COIL SPRING
REMOVAL
1) Hoist vehicle, allowing front suspension to hang free.
2) Remove wheels.
3) Remove axle shaft drive flange (For 4WD vehicle).
4) Remove front drive shaft circlip and washer (For 4WD vehicle).
5) Remove caliper bolts and suspend caliper with a wire hook.
CAUTION:
Hang removed caliper with a wire hook so as to prevent
brake hose from bending and twisting excessively or be-
ing pulled.
Don't operate brake pedal with pads removed.
6) If equipped with ABS, remove harness clamp bolt and remove
front wheel speed sensor from knuckle.
CAUTION:
Do not pull wire harness when removing front wheel
speed sensor.
Do not cause damage to surface of front wheel speed
sensor and do not allow dust, etc. to enter its installa-
tion hole.
7) Remove brake disc.
NOTE:
If brake disc can not be removed by hand, use 8 mm bolts
as shown.
YH4
GRAND
VITARA
3D-12 FRONT SUSPENSION
1. Lock washer
2. Screws 1. Axle shaft drive flange
WHEEL HUB (INCLUDED WHEEL BEARING)
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove axle shaft drive flange (4WD vehicle) or hub cap (2WD
vehicle).
3) If equipped with ABS, remove wheel speed sensor from knuckle
and harness clamp from strut.
4) Remove caliper bolt and suspend caliper.
CAUTION:
Hang removed caliper with a wire hook or the like so as to
prevent brake hose from bending and twisting excessively
or being pulled.
Don't operate brake pedal with pads removed.
5) Remove brake disc.
NOTE:
If brake disc can not be removed by hand, use 8 mm bolts as
shown.
6) Remove front wheel bearing lock washer by loosening 4 screws.
7) Remove front wheel bearing lock nut by using special tool.
Special Tool
(A): 09951-16050
8) Remove front wheel bearing washer.
9) Remove wheel hub component by hand.
YH4
GRAND
VITARA
2, (b)
1
1. Circlip
2. Large diameter
1. Front wheel speed sensor
2. Bolt
FRONT SUSPENSION 3D-15
7) For 4WD vehicle, apply lithium grease to front drive shaft wash-
er and front wheel spindle outer.
ªAº: Grease 99000-25010
8) For 4WD vehicle, when installing circlip to drive shaft, utilize
screw hole in drive shaft to pull it out and bring large diameter
of circlip at right as shown.
9) For vehicle with ABS, check that no foreign material is attached
to sensor and rotor. Install wheel speed sensor and its harness
clamp.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
CAUTION:
Do not pull wire harness or twist more than necessary
when installing front wheel speed sensor.
Fit harness grommet to inner fender securely.
Check that there is no clearance between sensor and knuckle.
10) Install brake disc and caliper assembly.
Tightening Torque
(e): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
YH4
GRAND
VITARA
5-4 BRAKES
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Not enough brak-
ing forceBrake oil leakage from brake lines.
Brake disc or pads stained with oil.
Overheated brakes.
Poor contact of shoes on brake drum.
Brake shoes linings stained with oil or wet
with water.
Badly worn brake shoe linings.
Defective wheel cylinders.
Malfunctioning caliper assembly.
Air in system.
Maladjusted sensor spring length of LSPV.
Broken sensor spring of LSPV.
Defective collar of LSPV.
Malfunctioning ABS (Antilock brake system),
if equipped.Locate leaking point and repair.
Clean or replace.
Determine cause and repair.
Repair for proper contact.
Replace.
Replace.
Repair or replace.
Repair or replace.
Bleed system.
Check or adjust.
Replace.
Replace.
Check system and replace as
necessary.
Brake pull
(Brakes not work-
ing in unison)Pad or shoe linings are wet with water or
stained with oil in some brakes.
Drum-to-shoe clearance out of adjustment in
some brakes.
(Malfunctioning auto adjusting mechanism)
Drum is out of round in some brakes.
Wheel tires are inflated unequally.
Malfunctioning wheel cylinders.
Disturbed front end alignment.
Unmatched tires on same axle.
Restricted brake pipes or hoses.
Malfunctioning caliper assembly.
Loose suspension parts.
Loose calipers.Replace.
Check for inoperative auto adjusting
mechanism.
Replace.
Inflate equally.
Repair or replace.
Adjust as prescribed.
Tires with approximately the same
amount of tread should be used on the
same axle.
Check for soft hoses and damaged
lines.
Replace with new hoses and new
brake pipes.
Check for stuck or sluggish pistons
and proper lubrication of caliper slide
bush.
Caliper should slide.
Check all suspension mountings.
Check and torque bolts to specifica-
tions.
Noise (High pitched
squeak without
brake applied)Front lining worn out.Replace linings.
Rear brake locked
prematurelyMaladjusted sensor spring length of LSPV.
Malfunction LSPV assembly.Check or adjust.
Replace assembly.
Brake locked
(For vehicles
equipped with
ABS)Malfunctioning ABS, if equipped.Check system and replace as
necessary.
YH4
GRAND
VITARA
BRAKES 5-5
ConditionPossible CauseCorrection
Excessive pedal
travel (Pedal
stroke too large)Partial brake system failure.
Insufficient fluid in master cylinder
reservoirs.
Air in system. (pedal soft / spongy)
Rear brake system not adjusted.
(malfunctioning auto adjusting mechanism)
Bent brake shoes.
Worn rear brake shoes.Check brake systems and repair as
necessary.
Fill reservoirs with approved brake
fluid.
Check for leaks and air in brake
systems.
Check warning light. Bleed system if
required.
Bleed system.
Repair auto adjusting mechanism.
Adjust rear brakes.
Replace brake shoes.
Replace brake shoes.
Dragging brakes
(A very light drag
is present in all
disc brakes
immediately
after pedal is
released)Master cylinder pistons not returning
correctly.
Restricted brake pipes or hoses.
Incorrect parking brake adjustment on rear
brakes.
Weakened or broken return springs in the
brake.
Sluggish parking-brake cables or linkage.
Wheel cylinder or caliper piston sticking.
Malfunctioning ABS, if equipped with ABS.Replace master cylinder.
Check for soft hoses or damaged
pipes and replace with new hoses
and / or new brake pipes.
Check and adjust to correct specifi-
cations.
Replace.
Repair or replace.
Repair as necessary.
Check system and replace as
necessary.
Pedal pulsation
(Pedal pulsates
when depressed
for braking)Damaged or loose wheel bearings.
Distorted steering knuckle or rear axle
shafts.
Excessive disc lateral runout.
Parallelism not within specifications.
Rear drums out of round.Replace wheel hub component.
Replace knuckle or rear axle shaft.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check runout.
Repair or replace drum as
necessary.
Braking noiseGlazed shoe linings, or foreign matters
stuck to linings.
Worn or distorted shoe linings.
Loose front wheel bearings.
Distorted backing plates or loose mounting
bolts.Repair or replace shoe lining.
Replace shoe lining (or pad).
Replace wheel hub component.
Replace or retighten securing bolts.
YH4
GRAND
VITARA
1. 4-way joint / 2-way joint
2. Master cylinder
3. LSPV
4. Right brake caliper
5. Left brake caliper
6. Right wheel cylinder
7. Left wheel cylinder
8. ABS actuator
: Air bleeding point [A]: Without ABS
[B]: With ABS
1. Plug cap2. Vinyl tube (See-through tube)
3. Container
[A]
[B]
BRAKES 5-7
CHECK AND ADJUSTMENT
BLEEDING BRAKES
CAUTION:
Brake fluid is extremely damaging to paint. If fluid should
accidentally touch painted surface, immediately wipe
fluid from paint and clean painted surface.
NOTE:
For vehicle equipped with ABS, make sure that ignition switch
turns off.
Be sure to bleed air of brake system according to following proce-
dure when its oil hydraulic circuit has been disconnected.
Hydraulic lines of brake system consists of two separate lines, one
for front wheel brakes and the other for rear wheel brakes.
Air bleeding is necessary at right and left front wheel brakes, left
rear wheel brake and LSPV (if equipped without ABS), i.e. 4 places
(3 places for vehicle with ABS) in all.
1) Fill master cylinder reservoir with brake fluid and keep at least
one-half full of fluid during bleeding operation.
2) Remove bleeder plug cap.
Attach a vinyl tube to bleeder plug of wheel cylinder, and insert
the other end into container.
3) Depress brake pedal several times, and then while holding it de-
pressed, loosen bleeder plug about one-third to one half turn.