2002 SUZUKI GRAND VITARA Front brake caliper

YH4
GRAND
VITARA
1. Caliper
2. Caliper pin bolts
3. Disc
1. Caliper
2. Wire hook
3. Pad
FRONT BRAKE 5B-3
DIAGNOSIS
Refer to Section 5 (BRAKES).
CHECK AND ADJUSTMENT
Refer to Section 5 (BRAKES).
ON-VEHICLE SERVICE
FRONT DISC BRAKE PAD
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove caliper pin bolts.
3) Remove E-ring from strut and then remove caliper from caliper
carrier.
NOTE:
Hang removed caliper with a wire hook or the like so as to
prevent brake hose from bending and twisting excessively
or being pulled. Don't operate brake pedal with pads re-
moved.
4) Remove pads.
INSPECTION
Brake Pad
Check pad lining for wear. When wear exceeds limit, replace with
new one.
CAUTION:
Never polish pad lining with sandpaper. If lining is polished
with sandpaper, hard particles of sandpaper will be depos-
ited in lining and may damage disc. When pad lining re-
quires correction, replace it with a new one.
Pad thickness (lining + rim) ªaº
Standard: 15.0 mm (0.590 in.) For SUMITOMO ELECTRIC. . .
brake calliper
15.5 mm (0.610 in.) For TOKICO brake caliper. . .
Service limit: 7.0 mm (0.275 in.) For SUMITOMO ELECTRIC. .
brake caliper
7.5 mm (0.295 in.) For TOKICO brake caliper. .
NOTE:
When pads are removed, visually inspect caliper for brake
fluid leak. Correct leaky point, if any.

YH4
GRAND
VITARA
5B-4 FRONT BRAKE
1. Wheel nut
2. Washer
(or spacer)
ªAº: Apply grease
Brake Disc
Before this inspection, brake pads must be removed.
Check disc surface for scratches in wearing parts. Scratches on
disc surface noticed at the time of specified inspection or replace-
ment are normal and disc is not defective unless they are serious.
But when there are deep scratches or scratches all over disc sur-
face, replace it. When only one side is scratched, polish and correct
that side.
Disc thickness ªaº
Standard: 22 mm (0.866 in.) For SUMITOMO ELECTRIC. . . . .
brake caliper
17 mm (0.670 in.) For TOKICO brake caliper. . . . .
Service limit: 20 mm (0.787 in.) For SUMITOMO ELECTRIC. .
brake caliper
15 mm (0.590 in.) For TOKICO brake caliper. .
Use wheel nuts and suitable plain washers to hold the disc securely
against the hub, then mount a dial indicator as shown and measure
the runout at 25 mm (0.98 in.) from the outer edge of the disc.
Limit on disc deflection: 0.15 mm (0.006 in.)
NOTE:
Check front wheel bearing for looseness before measure-
ment.
Cylinder Slide Guide Pin / Pin Bolt
Check guide pin for smooth movement as shown.
If it is found faulty, correct or replace. Apply rubber grease to guide
pin outer surface. Rubber grease should be the on whose viscosity
is less affected by such low temperature a ±40
C (±40
F).
Dust Boot
Check boot for breakage, crack and damage. If defective, replace.

YH4
GRAND
VITARA
1. Clips
2. Pads
3. Disc
4. Caliper carrier
5. Sensor
6. Shim
1. Caliper pin bolts
ELECTRIC brake
caliper
FRONT BRAKE 5B-5
INSTALLATION
NOTE:
See NOTE at the beginning of this section.
1) Install pad clips and pads.
NOTE:
Install pad with sensor to body center side of caliper.
2) Install caliper and torque caliper pin bolts to specification.
Tightening Torque
(a), (b): 27 N
.m (2.7 kg-m, 20.0 lb-ft) For TOKICO brake. .
caliper
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft) For SUMITOMO. . . . . .
(b): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
NOTE:
Make sure that boots are fit into groove securely.
3) Torque front wheel nuts to specification.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
4) Upon completion of installation, perform brake test.

YH4
GRAND
VITARA
1. Caliper
2. Flexible hose
3. Hose mounting bolt
4. Wire hook
5. Container
1. Cloth
5B-6 FRONT BRAKE
FRONT DISC BRAKE CALIPER
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove brake flexible hose mounting bolt from caliper. As this
will allow fluid to flow out of hose, have a container ready before-
hand.
3) Remove caliper pin bolts.
4) Remove caliper.
DISASSEMBLY
Before disassembly, clean all around caliper with brake fluid.
1) Remove anti noise shim (if equipped) and blow compressed air
into cylinder through bolt hole where flexible hose was fitted.
With this air pressure, piston can be pushed out of cylinder.
WARNING:
Do not apply too highly compressed air which will cause
piston to jump out of cylinder. It should be taken out grad-
ually with moderately compressed air. Do not place your
fingers in front of piston when using compressed air.

YH4
GRAND
VITARA
1. Caliper pin bolts
1. Flexible hose bolt
FRONT BRAKE 5B-9
Caliper
Before installing caliper (cylinder body) to carrier, check to ensure
that guide pin (pin bolt) inserted in each caliper carrier hole can be
moved smoothly in thrust direction.
NOTE:
Where temperature gets as low as ±30
C in cold weather, use
rubber grease whose viscosity varies very little even at ±40
C
(±40
F).
INSTALLATION
1) Install caliper to caliper carrier.
2) Torque caliper pin bolts to specifications.
Tightening Torque
(a), (b): 27 N
.m (2.7 kg-m, 20.0 lb-ft) For TOKICO brake. .
caliper
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft) For SUMITOMO. . . . .
(b): 85 N.m (8.5 kg-m, 61.5 lb-ft) ELECTRIC brake
85 N.m (8.5 kg-m, 61.5 lb-ft)caliper
NOTE:
Make sure that boots are fit into groove securely.
3) Install brake flexible hose as shown and torque hose mounting
bolt to specification.
Tightening Torque
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Torque wheel nuts to specification.
Tightening Torque
(c): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
5) After completing installation, fill reservoir with brake fluid and
bleed brake system. Perform brake test and check each
installed part for oil leakage.

YH4
GRAND
VITARA
1. 8 mm bolt
5B-10 FRONT BRAKE
FRONT BRAKE DISC
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove caliper assembly by loosening carrier bolts (2 pcs.).
CAUTION:
During removal, be careful not to damage brake flexible
hose and not to depress brake pedal.
3) Remove disc by using 8 mm bolts (2 pcs.).
INSPECTION
Refer to FRONT DISC BRAKE PAD INSPECTION.
INSTALLATION
NOTE:
See NOTE at the beginning of this section.
1) Install disc to wheel hub.
2) Install caliper assembly to steering knuckle.
3) Torque caliper carrier bolts to specification.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
4) Torque front wheel nuts to specifications.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
5) Upon completion of installation, perform brake test.

YH4
GRAND
VITARA
FRONT BRAKE 5B-11
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake caliper bleeder plug
(For SUMITOMO ELECTRIC brake caliper)8.00.806.0
Brake caliper bleeder plug
(For TOKICO brake caliper)8.50.856.5
Caliper pin bolt (For TOKICO brake caliper)272.720.0
Caliper pin bolt (M10)
(For SUMITOMO ELECTRIC brake caliper)505.036.5
Caliper pin bolt (M12)
(For SUMITOMO ELECTRIC brake caliper)858.561.5
Flexible hose bolt232.317.0
Brake carrier bolt858.561.5
Wheel nut10010.072.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.

YH4
GRAND
VITARA
PARKING AND REAR BRAKE 5C-17
09943-35512
Brake drum remover
(Front wheel hub remover)09942-15510
Sliding hammer
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Wheel cylinder bleeder plug7.50.755.5
Parking brake lever bolt232.317.0
Wheel cylinder bolt (For non sealed type)8.50.856.5
Wheel cylinder bolt (For gasket sealed type)111.112.0
Brake pipe flare nut161.612.0
Brake back plate nut232.317.0
Wheel nut10010.072.5
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.
Water tight
sealantSEALING COMPOUND 366E
99000-31090
To apply to mating surfaces of brake back
plate and rear wheel cylinder.
SealantSUZUKI BOND NO. 1215
99000-31110

To apply to mating surfaces of brake back
plate and rear axle housing.

To apply mating surfaces of brake back
plate and rear wheel bearing retainer.
SPECIAL TOOLS