2002 SUZUKI GRAND VITARA Shaft

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-19
1. Knuckle
2. Knuckle cap
3. Wheel spindle 1. Oil seal
2. Drive shaft
3. Drive shaft
thrust washer
Type A Type B

Tighten wheel spindle nut to specified torque.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For 4WD vehicle
Press-fitting inner oil seal.
Drive in inner oil seal until its end contacts stepped surface of
knuckle by using special tools.
Special Tool
(B): 09944-66010
(C): 09924-74510

For 4WD vehicle

Apply lithium grease to oil seal lip and into its hollow to fill more
than 60% of its vacant space.

Apply lithium grease ªAº to drive shaft.
ªAº: Grease 99000-25010

Press-fit front drive shaft thrust washer to drive shaft, if it is re-
moved (for Type B drive shaft thrust washer). Apply lithium
grease ªAº to drive shaft thrust washer.
ªAº: Grease 99000-25010

Apply lithium grease ªAº and install front drive shaft thrust wash-
er with its chamfered side facing to center side (for Type A drive
shaft thrust washer).
ªAº: Grease 99000-25010

For 2WD vehicle
Remove grease, old sealant and dusts from mating surfaces of
knuckle cap and knuckle to clean, apply water tight sealant to cap
mating surface evenly, and install cap to knuckle.
ªBº: Sealant 99000-31090

YH4
GRAND
VITARA
(a)
1. Axle shaft drive flange
2. Bolt1. Hub cap
2. Wheel hub
3D-20 FRONT SUSPENSION

Tighten control arm ball stud nut
When tightening ball stud nut, use new nut and tighten it to speci-
fied torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)

For 2WD vehicle
Apply water tight sealant to mating surface of wheel hub and
install hub cap to wheel hub.
ªAº: Sealant 99000-31090

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For installation procedures of wheel hub component, refer to
ªWHEEL HUB (INCLUDED WHEEL BEARING)º in this section.

Connect tie-rod end to knuckle and tighten new tie-rod end nut.
Tightening Torque
(a): 43 N
.m (4.3 kg-m, 31.5 lb-ft)

For any tightening torque other than those specified in text, refer
to ªTIGHTENING TORQUE SPECIFICATIONº in this section.

YH4
GRAND
VITARA
3D-24 FRONT SUSPENSION
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSENO.
Lithium greaseSUZUKI SUPER GREASE (A)
(99000-25010)
Bearing inner oil seal / drive shaft oil seal
Recess of wheel spindles
Spindle outer washer
Spindle part of drive shaft
Spindle bush (inside and flange part)
Spindle inner washera
b
c
d
e
f
SealantSUZUKI BOND NO. 1215
(99000-31110)Mating surfaces of wheel spindle
and knuckle1
Sealing compound
SUZUKI SEALING COM-
POUND 366E
(99000-31090)
Front axle cap
Mating surfaces of wheel hub and drive
flange
Knuckle cap
Hub capA
B
C
D

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-25
09923-74510
Bearing remover09930-30102
Sliding shaft09924-74510
Bearing installer handle09941-66010
Bump stopper wrench
09942-15510
Sliding hammer09943-35512
Brake drum remover09944-68210
Bearing & oil seal installer 09944-66010
Wheel hub / knuckle oil
seal installer
09951-16050
Wheel bearing tightening tool09951-46020
Control arm remover support 09951-16060
Control arm bush remover
(front)09913-80112
Bearing installer
09925-58210
Oil seal installer09913-85210
Oil seal installer
09952-86510
Front sensor rotor installer
SPECIAL TOOLS

YH4
GRAND
VITARA
3E
REAR SUSPENSION 3E-1
GENERAL DESCRIPTION3E- 2 . . . . . . . . . . . . . .
DIAGNOSIS3E- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3E- 3. . . . . . . . . . . . . . . . . . . . . .
Shock Absorber Check 3E- 3. . . . . . . . . . . . . . . .
Lower / Upper / Lateral Rod Check 3E- 3. . . . . . . .
Axle Housing and Coil Spring Check 3E- 3. . . .
Bearing Retainer & Axle Shaft Inner Oil
Seal Check 3E- 4. . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Disc, Nut & Bearing Check 3E- 4. . . . . .
ON-VEHICLE SERVICE3E- 5 . . . . . . . . . . . . . . . .
Shock Absorber 3E- 5. . . . . . . . . . . . . . . . . . . . . . Coil Spring 3E- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Lower Rod 3E- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Rod 3E- 9. . . . . . . . . . . . . . . . . . . . . . . . . .
Lateral Rod 3E-10. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Axle Shaft and Wheel Bearing 3E-10. . . . .
Rear Axle Shaft Inner Oil Seal 3E-15. . . . . . . . . .
Rear Axle Housing 3E-16. . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3E-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3E-23 . . . . . .
SPECIAL TOOLS3E-24 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3E
REAR SUSPENSION
NOTE:

All suspension fasteners are an important attaching part in that it could affect the performance of vital
parts and systems, and / or could result in major repair expense. They must be replaced with one of the
same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality or substitute design. Torque values must be used as specified during reas-
sembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any suspension part. Replace it with a new part, or damage
to the part may result.
CONTENTS

YH4
GRAND
VITARA
1. Rear axle housing
2. Coil spring
3. Axle shaft
4. Shock absorber
5. Upper rod
6. Lower rod
7. Oil level plug
8. Wheel bearing retainer
9. Rear wheel bearing
10. Brake back plate
11. Oil drain plug
12. Lateral rod
NOTE:
When installing differential gear oil drain
plug, clean the thread portion of the plug and
then apply sealant (SUZUKI BOND No. 1215,
99000-31110) to the portion.
8
3E-2 REAR SUSPENSION
GENERAL DESCRIPTION
Rear suspension is 5 link type of rigid axle which consists of coil springs, rear axle, shock absorbers, upper rods,
lower rods and lateral rod.
The lower rod and upper rod are connected with the axle and body by using bushes so that axle moves up and
down with bushes as their supporting points.
The shock absorber is installed between the body and axle to absorb up-and-down movement of the vehicle body.

YH4
GRAND
VITARA
3E-4 REAR SUSPENSION
REAR SUSPENSION FASTENERS
Check each bolt and nut fastening suspension parts for tightness.
Tighten loose one, if any, to specified torque, referring to ªTIGHT-
ENING TORQUE SPECIFICATIONSº of this section.
BEARING RETAINER AND AXLE SHAFT
INNER OIL SEAL CHECK

When brake drum has been removed, check inside of brake drum
for gear oil leakage.

Also, check backside of brake back plate for oil leakage.
If oil leakage is found, replace defective oil seal.

Whenever it is possible to check oil seal during disassembly,
check its lip for wear.
If oil leakage or worn lip is found, replace defective oil seal.
WHEEL DISC, NUT & BEARING CHECK

Inspect each wheel disc for dents, distortion and cracks. A disc
in badly damaged condition must be replaced.

Check wheel hub nuts for tightness and retighten to specification
as necessary.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)

Check wheel bearings for wear. When measuring thrust play, ap-
ply a dial gauge to axle shaft center after removing wheel center
cap from wheel.
Thrust play limit
Rear0.8 mm (0.03 in.)
When measurement exceeds limit, replace bearing.

By rotating wheel actually, check wheel bearing for noise and
smooth rotation. If it is defective, replace bearing.

YH4
GRAND
VITARA
(a)
(a)
1. Bolt
2. Washer
3. Lateral rod
1. Nut
1
3E-10 REAR SUSPENSION
LATERAL ROD
REMOVAL
1) Hoist vehicle.
2) Remove lateral rod mounting bolts.
3) Remove lateral rod.
INSTALLATION
1) Install lateral rod to rear axle, and vehicle body.
2) Lower hoist.
3) Tighten lateral rod mounting bolts to specified torque.
Tightening Torque
(a): 90 N
.m (9.0 kg-m, 65.0 lb-ft)
REAR AXLE SHAFT AND WHEEL BEARING
REMOVAL
1) Remove rear brake drum. For details, refer to REAR BRAKE
DRUM REMOVAL in SECTION 5C.
2) Drain gear oil from rear axle housing by loosening drain plug.
3) Remove rear wheel bearing retainer nuts from axle housing.