2002 SUZUKI GRAND VITARA Seat belts rear

YH4
GRAND
VITARA
BODY SERVICE 9-75
1. Canvas top
2. Rear topbow
3. Side body garnish
4. Luggage mat end garnish
5. Assistant grip
6. Sunshade assembly
7. Sunshade hook
8. Front topbow lock
9. Canvas top snap
10. Front seat belt
11. Front pillar trim
12. Rear side inner lower trim
13. Rear side inner upper trim
14. Room light connector
15. Room light harness clamp
16. Roof trim
17. Left-front seat belt
ROOF TRIM (2 DOOR MODEL)
REMOVAL
1) Remove canvas top.
2) Remove rear topbow.
3) Remove side body garnishes.
4) Remove luggage mat end garnish.
5) Remove assistant grips.
6) Remove sunshade assemblies.
7) Remove sunshade hooks.
8) Remove front topbow locks.
9) Remove canvas top snaps.
10) Remove front seat belts.
11) Remove front pillar trims.
12) Remove rear side inner lower trims.
13) Remove rear side inner upper trims.
14) Disconnect room light connector and remove room light har-
ness clamp.
15) Remove roof trim.
CAUTION:
Be very careful not to separate roof trim consists of 4
components when removing. If disassemble it, it could
not be assembled to original unit.

YH4
GRAND
VITARA
10-2 RESTRAINT SYSTEM
Driver Side Seat Belt: Seat belt with ELR
Front Passenger Side Seat And
Rear Left And Right Seat Belts: Seat belt with A-ELR
Rear Center Seat Belt (If Equipped): Seat belt without ELR and A-ELR
Supplemental Restraint System: Driver and front passenger side air bags
1. Driver side seat belt
2. Front passenger side seat belt
3. Rear left seat belt
4. Rear right seat belt
5. Rear center seat belt (If equipped)
6. Driver side air bag
7. Passenger side air bag
GENERAL DESCRIPTION
Seat belt with ELR
The seat belt with Emergency Locking Retractor (ELR) is designed so that it locks immediately (to prevent the web-
bing from being pulled out of the retractor any further) when any of the following items is detected as exceeding
each set value; speed at which the webbing is pulled out of the retractor, acceleration or deceleration of the vehicle
speed, and inclination.
Seat belt with A-ELR
The automatic and emergency locking retractor (A-ELR) works as an Emergency Locking Retractor (ELR) till its
webbing is pulled all the way out and then on as an Automatic Locking Retractor (ALR) till it is retracted fully.
ALR: Automatically locks when the webbing is pulled out from the retractor and allowed to retract even a little.
Then the webbing can not be pulled out any further, unless it is wound all the way back into the retractor, which
releases the lock and allows the webbing to be pulled out.
Driver and front passenger side air bags
The driver and front passenger side air bags are components of the air bag system. In occurrence of a front collision
with an impact larger than a certain set value, they are activated by the ignition signal from SDM to supplement
protection offered by the driver and front passenger seat belts.

the driver air bag (inflator) module is deployed from the center of the steering column

the passenger air bag (inflator) module from the top of the instrument panel in front of the front passenger seat
For more information, refer to SECTION 10B ªAir Bag Systemº.

YH4
GRAND
VITARA
10A-6 SEAT BELT
1. Upper anchor
2. Lower anchor
3. Retractor assembly
4. Buckle: If equipped* *
REAR SEAT BELT
WARNING:
Be sure to read ªService Precautionsº before starting to work and observe every precaution during
work.
REMOVAL
Refer to the figure below to remove rear seat belts.
INSPECTION
Check the rear seat belt in the same way as when inspecting front seat belt. (Refer to page 10A-4.)
INSTALLATION
Install the rear seat belt observing the same precautions as when installing front seat belt. (Refer to page 10A-5.)
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Upper and lower anchor bolt353.525.5
Retractor assembly bolt353.525.5
Retractor assembly screw5.50.554.0
Buckle bolt353.525.5

YH4
GRAND
VITARA
12
3
3
1. Driver side air bag
2. Passenger side air bag
3. Seat belt pretensioner
(if equipped)
1-1. SDM
1-1. Sensor
1-2. Voltage converter1-3. Safing sensor
1-4. Micro-controller
1-5. Energy reserve circuit1-6. Ignition driver circuit
1-2. Power source
3. Driver air bag 4. Passenger air bag
5. Seat belt pretensioner (if equipped)
6. Squib circuit
AIR BAG SYSTEM 10B-3
GENERAL DESCRIPTION
With the air bag system which includes air bags for both the driver's
and passenger's sides as well as the seat belt pretensioners (if
equipped), the sag of the seat belt is taken up, the driver air bag (in-
flator) module is deployed from the center of the steering column
and the passenger air bag (inflator) module from the top of the
instrument panel in front of the front passenger seat in occurrence
of a front collision with an impact larger than a certain set value to
supplement protection offered by the driver and front passenger
seat belts.
The air bag system is designed to activate only in severe frontal col-
lisions. It is not designed to activate in rear impacts, side impacts,
rollovers, or minor frontal collisions, since it would offer no protec-
tion in those types of accidents.