2002 SUBARU IMPREZA lock

Instruments and controls
3-6
Meters and gauges Speedometer
The speedometer shows the vehicle speed. Odometer/Trip meter
HG3005BB
1) Trip meter 2) Odometer
This meter displays the odometer and two trip me- ters when the ignition switch is in the “LOCK”,
“ACC” or “ON” position.
Odometer
The odometer shows the total distance that the ve-
hicle has been driven.
Double trip meter
HG3006BB
1) A trip meter 2) B trip meter
The trip meter shows the distance that the vehicle
has been driven since you last set it to zero.
To change the mode indication, briefly push theknob.
Each press of the knob changes the function in the
following order.
A trip meter
B trip meter
To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob
pushed for more than 2 seconds.

Instruments and controls
3-7
– CONTINUED –
CAUTION
To ensure safety, do not attempt to change the
function of the indicator during driving, as an
accident could result.
NOTE If the connection between the combination meter
and battery is broken for any reason such as ve-hicle maintenance or fuse replacement, the datarecorded on the trip meter will be lost. Tachometer
The tachometer shows the engine speed in thou-
sands of revolutions per minute.
CAUTION
Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control
module to protect the engine from overrev-ving. The engine will resume running normallyafter the engine speed is reduced below thered zone.
Fuel gauge
HG3007BB
1) Low fuel warning light
The fuel gauge shows the approximate amount of
fuel remaining in the tank.
The gauge does not return to “E” even though the
ignition switch is in the “ACC” or “LOCK” position.
The gauge may move slightly during braking, turn- ing or acceleration due to fuel level movement in the tank.

Instruments and controls
3-14
Always make sure this light is out before you start to drive. Front-wheel drive warning light
(for AT vehicles – if equipped)
This light comes on when All Wheel Drive is disen-
gaged and the drive mechanism is switched to FrontWheel Drive for maintenance or similar purposes. Shift position indicator (AT vehicles)
This indicator shows the position of the shift lever. Turn signal indicator lights
These lights show the operation of the turn signal or
lane change signal.
If the indicator lights do not blink or blink rapidly, the
turn signal bulb may be burned out. Replace thebulb as soon as possible. Refer to the “Replacing
bulbs” section in chapter 11.
High beam indicator light
This light shows that the headlights are in the highbeam mode.This indicator light also comes on when operating
headlight flasher. Clock
HG3009BB
1) “S”
button
2) “H” button 3) “M”
button
To set the hour, press the “H” button. To set the min-
utes, press the “M” button. To reset the minutes the
“00” with a radio time signal, push the “S” button.
CAUTION
To ensure safety, do not attempt to set the time during driving, as an accident from inad- equate steering operation could result.

Instruments and controls
3-18
the direction of the turn or lane change. The lever
will return automatically to the neutral position when
you release it.Illumination brightness control
When the lighting switch is in the
“p ” or “a ”
position, you can adjust brightness of the instrument
panel illumination for better visibility.
HB2017BC
1) To brighten, turn the control dial coun- terclockwise.
2) To darken, turn the control dial clock-
wise.

Instruments and controls
3-20
Wiper and washer
WARNING
In freezing weather, do not use the windshield
washer until the windshield is sufficiently
warmed by the defroster.Otherwise the washer fluid can freeze on the
windshield, blocking your view.
CAUTION
Do not operate the washer continuously for
more than ten seconds, or when the washer
fluid tank is empty. This may cause overheat-
ing of the washer motor. Check the washer
fluid level frequently, such as at fuel stops. Do not operate the wipers when the wind-
shield or rear window is dry. This may scratchthe glass, damage the wiper blades and causethe wiper motor to burn out. Before operating
the wiper on a dry windshield or rear window,
always use the windshield washer. In freezing weather, be sure that the wiper
blades are not frozen to the windshield or rear window before switching on the wipers.Attempting to operate the wiper with the
blades frozen to the window glass could
cause not only the wiper blades to be dam-aged but also the wiper motor to burn out. Ifthe wiper blade is frozen to the window glass,
be sure to operate the defroster, windshield wiper deicer (if equipped) or rear window
defogger before turning on the wiper.
If the wipers stop during operation because
of ice or some other obstruction on the win-
dow, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turnthe ignition switch to the “LOCK” position and
clean the window glass to allow proper wiperoperation. Use clean water if windshield washer fluid is
unavailable. In areas where water freezes in
winter, use SUBARU Windshield Washer Fluidor the equivalent. (See the “Windshield wash-
er fluid ” section in chapter 11.)
Also, when driving the vehicle when there are
freezing temperatures, use non-freezing type wiper blades. Do not clean the wiper blades with gasoline
or a solvent, such as paint thinner or benzene.

Instruments and controls
3-23
– CONTINUED –
Washer
HB2020BA
To wash the windshield, push the washer button at
the end of the wiper control lever. The washer fluid
sprays until you release the washer button. The wip- ers operate while you push the button.
Rear window wiper and washer switch (if equipped)HB2021BB
1) Rear wiper 2) Washer
Rear wiper
The rear wiper offers intermittent operation only.
To turn the rear wiper on, turn the knob on the end of
the wiper control lever to the “ON” position.
To turn the wiper off, return the knob on the end ofthe lever to the “OFF” position.
Washer
To wash the rear window while the rear wiper is op-
erating, turn the knob on the end of the wiper control
lever counterclockwise to the “
” position. The

Instruments and controls
3-24
washer fluid sprays until you release the knob.
To wash the rear window when the rear wiper is not
in use, turn the knob on the end of the wiper controllever clockwise to the “
” position. The washer
fluid sprays and the wiper operates until you release the knob. Rear window defogger switch
The rear window defogger operates only when the
ignition switch is in the
“ON” position.
The rear window defogger switch is located on the
climate control panel.
The defogger will automatically shut off after about
15 minutes. If the window clears before that time,
push the switch to turn it off. It also turns off when
the ignition switch is turned to the “ACC” or “LOCK”
position. If defrosting or defogging is desired when
you restart your vehicle, you have to push the switch
to turn it on again.
HB5009BC
1) OFF
2) ON 3) Push

Instruments and controls
3-29
– CONTINUED –
The mirrors can also be adjusted manually.
Outside mirror defogger (if equipped)
The outside mirror defogger shares the switch with
rear window defogger.
The outside mirror defogger operates only when the
ignition switch is in the “ON” position.
HB5009BC
1) OFF
2) ON 3) Push
To turn on the outside mirror defogger, push the
switch. To turn it off, push the switch again. The indi-
cator light located on the switch lights up while the
outside mirror defogger is operating.
The defogger will automatically shut off after about 15 minutes. If the mirror clears before that time,
push the switch to turn it off. It also turns off when
the ignition switch is turned to the
“ACC” or “LOCK”
position. If defrosting or defogging is desired when
you restart your vehicle, you have to push the switch
to turn it on again. NOTE While the outside mirror defogger is operating, the rear window defogger also operates.
CAUTION
To prevent the battery from being discharged,
do not operate the defogger continuously for
any longer than necessary.