2002 SUBARU FORESTER battery

Instruments and controls3-15
–
CONTINUED –
The warning light comes on right after the engine is started but
goes out immediately, remaining off. The warning light remains on after the engine has been started,
but it goes out when the vehicle speed reaches about 8 mph (12km/h). The warning light comes on during driving, but it goes out
immediately and remains off.
When driving with an insufficient battery voltage such as when the en-
gine is jump started, the ABS warning light may come on. This is due to
the low battery voltage and does not indicate a malfunction. When the
battery becomes fully charged, the light will go out. VDC (Vehicle Dynamics Control) warning light (if equipped)
This warning light comes on when the ignition switch is turned to the
“ON” position and goes out after the engine has started. It indicates that
the VDC system is operational.
The VDC system is probably inoperative under any of the following
conditions. Immediately have your vehicle checked at a SUBARU dealer. The VDC warning light does not come on when the ignition switch is
turned to the “ON” position.
The VDC warning light remains on after the engine has started and
stays lit even when the vehicle speed reaches about 8 mph (12 km/h). The VDC warning light comes on while the vehicle is running.
If the electrical circuit of the VDC system itself becomes faulty, the
VDC warning light only comes on. At this time, the ABS (Anti-lock Brake
System) remains fully operational. The warning light comes on when the electronic control system of the
ABS/VDC system becomes faulty.
The VDC system provides its ABS control through the electrical circuit of
the ABS system. Accordingly, if the ABS is inoperative, the VDC system
also becomes unable to provide ABS control. As a result, the VDC sys-
tem becomes inoperative, causing the VDC warning light to come on.
Though both the VDC and ABS systems are inoperative in this case, the
ordinary functions of the brake system are still available. You will be safe

Instruments and controls3-19
–
CONTINUED –
“Replacing bulbs ” section in chapter 11.
High beam indicator light
This light shows that the headlights are in the high beam mode.
This indicator light also comes on when operating headlight flasher. Clock
HB2013BA
To set the time, turn the setting knob clockwise to advance and counter-
clockwise to retard the time.
Light control switch
WARNING
To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch oper-ates only when the ignition switch is in the “ON” position. In any
other position, the vehicle ’s lights will be out.
If you park your vehicle on a roadside at night, use the hazardwarning flasher to alert the other drivers.

Instruments and controls3-23
–
CONTINUED –
Parking light switch
HB2018BA
The parking light switch operates regardless of the ignition switch posi- tion.
By pushing the front end of this switch, following lights will come on.
– Parking lights
– Front and rear side marker lights
– Tail lights
– License plate lights
To turn off, push the rear end of the parking light switch.
Avoid leaving these lights on for a long time because that will run down
the battery.

Instruments and controls3-29
–
CONTINUED –
Rear window defogger switch
CAUTION
Do not use sharp instruments or window cleaner containing
abrasives to clean the inner surface of the rear window. They may
damage the conductors printed on the window. To prevent the battery from being discharged, do not operate
the defogger continuously for any longer than necessary.
The rear window defogger operates only when the ignition switch is inthe “ON” position.
The rear window defogger switch is located on the climate control panel.
The defogger will automatically shut off after about 15 minutes. If the win-
dow clears before that time, push the switch to turn it off. It also turns off
when the ignition switch is turned to the “ACC” or “LOCK” position. If
defrosting or defogging is desired when you restart your vehicle, you
have to push the switch to turn it on again.
For vehicles with manual heating and air conditioning systems
HB5009BB
To turn on the defogger, push the switch. To turn it off, push the switch again.
The indicator light located on the switch lights up while the rear win-dow defogger is operating.

3-30
For vehicles with automatic climate control
HB3016BB
To turn on the defogger, push the switch. To turn it off, push the switch again.The indicator light “u ” lights up on the climate control display panel
while the rear window defogger is operating.
Windshield wiper deicer (if equipped)
CAUTION
To prevent the battery from being discharged, do not operate thewindshield wiper deicer continuously for any longer than neces-
sary.
HB2027BB

3-36
Outside mirror defogger (if equipped) CAUTION
To prevent the battery from being discharged, do not operate the
defogger continuously for any longer than necessary.
The outside mirror defogger operates only when the ignition switch isin the “ON” or “ACC” position.
HB4004CB
To turn on the outside mirror defogger, push the switch while the en- gine is running.The indicator light located on the switch will come on when the out-
side mirror defogger heater in operation.
To turn it off, push the switch again.
Tilt steering wheel
WARNING
Do not adjust the steering wheel tilt position while driving. This
may cause loss of vehicle control and result in personal injury.

4-18
: Outside air is drawn into the passenger compartment. Whenthe air conditioning system is operated in the “AUTO” mode,
this position is selected automatically. The indicator light “
” on the control panel comes on when this switch is
pushed.
n Temperature control dial
HB4033BB
NOTE A setting of about 77 °F (25 °C) throughout the year is recom-
mended. The temperature setting remains even after the ignition switch
is turned to the “OFF”. However, if the battery cables are discon-
nected, the temperature will be set to 77 °F (25 °C) automatically.
Set desired temperature by turning the temperature control dial; turn
the dial clockwise to raise the temperature setting and turn it counter-clockwise to lower it.
The temperature can be set in increments of 1 °F within a range of 65
– 85 °F for US models and in increments of 0.5 °C within a range of 18
– 32 °C for Canadian models.
Even when quick cooling or warming is necessary, you do not have to
change the temperature setting. The Automatic Climate Control sys-
tem operates at maximum performance until the air in the passenger
compartment reaches to the specified temperature.

Audio5-11
–
CONTINUED –
Press the “SCAN” button again to cancel the SCAN mode and to stop
on any displayed frequency.
When the “SCAN” button is pressed for automatic tuning, stations are
scanned in the direction of low frequencies to high frequencies only.
Automatic tuning may not function properly if the station reception is
weakened by distance from the station or proximity to tall buildingsand hills. Selecting preset stations
Presetting a station with a “preset button ”
5 allows you to select that
station in a single operation. Up to six WB (if equipped), AM, FM1 and
FM2 stations each may be preset. How to preset stations
1. Press the “BAND” button 3 to select FM1, FM2, AM or WB (if
equipped) reception.
2. Press the “SCAN” button or tune the radio manually until the
desired station frequency is displayed.
3. Press one of the preset buttons for more than 2 seconds to store
the frequency. At this time, there will momentarily be no sound from
the radio. If the button is pressed for less than 2 seconds, the preced-
ing selection will remain in memory.
NOTE If the connection between the radio and battery is broken for any
reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.