2002 PEUGEOT 807 warning

YOUR 807 IN DETAIL109
T
ailgate release
This enables the tailgate to be
unlocked in the event of a central
locking fault.  Fold back a 2 nd
row rear seat,
 Fold back a 3 rd
row rear seat or
the bench seat to gain access to
the lock from inside the boot,
 Insert a small screwdriver into
hole Ain the lock and push it
towards the left to unlock the
tailgate .
TAILGATE
Simultaneous locking or unlock
ing of the tailgate and the doors
The tailgate is locked or unlocked by
the remote control or the driver's
door or passenger door lock.
To open, operate the handle
Aand
lift the tailgate.
Note: The tailgate locks automatical
ly when the vehicle is being driven at
more than 6 mph (10 km/h) and
unlocks when one of the doors is
opened.
"Tailgate open" warning
When the engine is running or the
vehicle is being driven, you are
warned if the tailgate is not closed
correctly by a diagram on the
multi–function display, accompanied
by an audible signal. Partially opening rear
windows
To partially open the rear windows,
tilt the lever
Aand push it fully to
lock the windows in the open posi
tion.
18-11-2002

YOUR 807 IN DETAIL
110
SUNROOFS You have three sunroofs each with
an independent control.
However, the front passengers' con
trol can also operate the two rear
sunroofs simultaneously.
•partially open the roof: press and
hold part Aof the switch.
•to open the roof completely:
press part Aof the switch briefly.
•to close it completely: press part
B of the switch briefly, then keep it
pressed.
•safety autoreverse
When the sunroof is sliding closed
and meets an obstacle, it stops then
opens again.
Note: in the presence of ice, if the
sunroof does not close, press the
control until the roof is fully open,
then close the roof. Note:
following reconnection of the
battery, if the sunroof does not close,
release the control and press it sev
eral times until the roof is fully
closed. Continue to press the control
for approximately five seconds after
closing.
Disarming of the 2 nd
and 3 rd
row
controls:
– press the rear electrical functions disarming switch.
Note: the sunroof shutter is manual.
To open it, lift the handle and slide it
rearwards.
To close it, slide it forwards until the
handle locks. OPENING THE BONNET
From inside:
– lift the cover at the left foot of the
passenger seat.
– pull the control upwards.
From outside: lift the catch and
raise the bonnet.
Bonnet strut
Secure the strut to hold the bonnet open.Before closing the bonnet, replace
the strut in its housing.
To close
Lower the bonnet and release it at
the end of its travel. Check that the
bonnet is properly locked.
"Bonnet open" warning
This warning is linked to the alarm
option only.
With the engine running or the
vehicle moving, a diagram on the
multifunction display, accompanied
by an audible signal, warns you that
the bonnet is not properly closed.
18-11-2002

YOUR 807 IN DETAIL111
FILLING
THE
FUEL TANK
Low fuel level
When the tank's minimum
level is reached, this warn
ing light comes on, accom
panied by the message
"Fuel level low" on the
multi–function display.
You have enough fuel left to cover
approximately 30 miles (50 km).
If the warning light flashes, this
indicates a fuel gauge malfunction.
Contact a PEUGEOT dealer.
If the warning light flashes, accom
panied by the message "Fuel circuit
disarmed" , this indicates that the
fuel supply has been cut off.
Restore the supply (refer to the
corresponding section). The tank must be filled with fuel with
the engine off
.
 Open the fuel filler flap.
 Insert the key then turn it to the
left.
 Remove the cap and attach it to
the clip located on the inside of
the flap.
A label on the inside of the flap indi
cates which type of fuel to use.
If you fill your tank, do not continue
after the third cutoff of the pump
nozzle. This could result in vehicle
malfunctions.
The capacity of the tank is approx
imately 18 gallons (80 litres).  After filling the tank, lock the cap
and close the flap.
When the fuel filler flap isopen, a system limits theopening of the rear left
sliding side door. The keycannot be removed from
the capÕs lock until the cap is refit-ted on the tank.
18-11-2002

YOUR 807 IN DETAIL
116
TRIP COMPUTER
Each time the button on the end of the
wiper stalk is pressed, the following
sequence of data is displayed:
Monochrome screen CT
– the "vehicle" tab with:
• range, current consumption and the distance still to be driven,
– tab '1' (route '1') with:
• the distance driven and the aver age speed calculated over route
'1'
– tab '2' (route '2') with the same fea
tures.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
Monochrome screen B
the remaining range
the distance travelled
the average consumption
the current consumption
the average speed
In addition, it allows access to the
warning log information and to the
Excess speed warning function.
Zero reset
Press the stalk for more than two
seconds.
Colour screen DT
– the "Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
– 'Route 1' with:
• the distance travelled,
• the average coonsumption,
• the average speed,
– 'Route 2' with the same features.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
18-11-2002

Distance remaining to be
travelled
This is the distance remaining to the
destination. It can either be calculat
ed by the navigation if guidance is
activated, or entered by the user,
minus the distance covered since
the distance was entered.
Note:if digits are missing, dashes
are displayed in their place.
Average speed
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The warnings log
This summarises the active warning
messages by displaying them on the
multifunction display.
The excess speed warning
function *
This monitors the maximum speed
required. In the event that the pro
grammed speed is exceeded, the
message ''Speed too high'' appears
on the multifunction display, accom
panied by an audible signal.
Programming
Accelerate to the desired speed.
Keep pressing the control to store in
memory.
* During the year.
YOUR 807 IN DETAIL 117
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
Note:
this figure may increase if there
is a change in the style of driving or
the road surface, producing a signifi
cant drop in current consumption.
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.
Current consumption
This is the average quantity of fuel
consumed during the last few sec
onds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
This is the average fuel consumption
since the computer was last set to
zero.
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero. Activation
Keep pressing the control until the
display indicates
''Excess speed
ON'' .
Switching off
Keep pressing the control until the
display indicates ''Excess speed
OFF'' .
The routes
The routes "1" and ''2''are indepen
dent but have identical application.
Route "1"for example allows you to
make daily calculations and route
"2" monthly calculations.
18-11-2002

YOUR 807 IN DETAIL
116
TRIP COMPUTER
Each time the button on the end of the
wiper stalk is pressed, the following
sequence of data is displayed:
Monochrome screen CT
– the "vehicle" tab with:
• range, current consumption and the distance still to be driven,
– tab '1' (route '1') with:
• the distance driven and the aver age speed calculated over route
'1'
– tab '2' (route '2') with the same fea
tures.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
Monochrome screen B
the remaining range
the distance travelled
the average consumption
the current consumption
the average speed
In addition, it allows access to the
warning log information and to the
Excess speed warning function.
Zero reset
Press the stalk for more than two
seconds.
Colour screen DT
– the "Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
– 'Route 1' with:
• the distance travelled,
• the average coonsumption,
• the average speed,
– 'Route 2' with the same features.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
18-11-2002

Distance remaining to be
travelled
This is the distance remaining to the
destination. It can either be calculat
ed by the navigation if guidance is
activated, or entered by the user,
minus the distance covered since
the distance was entered.
Note:if digits are missing, dashes
are displayed in their place.
Average speed
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The warnings log
This summarises the active warning
messages by displaying them on the
multifunction display.
The excess speed warning
function *
This monitors the maximum speed
required. In the event that the pro
grammed speed is exceeded, the
message ''Speed too high'' appears
on the multifunction display, accom
panied by an audible signal.
Programming
Accelerate to the desired speed.
Keep pressing the control to store in
memory.
* During the year.
YOUR 807 IN DETAIL 117
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
Note:
this figure may increase if there
is a change in the style of driving or
the road surface, producing a signifi
cant drop in current consumption.
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.
Current consumption
This is the average quantity of fuel
consumed during the last few sec
onds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
This is the average fuel consumption
since the computer was last set to
zero.
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero. Activation
Keep pressing the control until the
display indicates
''Excess speed
ON'' .
Switching off
Keep pressing the control until the
display indicates ''Excess speed
OFF'' .
The routes
The routes "1" and ''2''are indepen
dent but have identical application.
Route "1"for example allows you to
make daily calculations and route
"2" monthly calculations.
18-11-2002

YOUR 807 IN DETAIL
118
Trip computer configuration
This function allows inputting of the
distance to the destination (when
guidance is not activated; otherwise
the information is given by the navi
gation) and also changing of the
units (°C or °F, km and litres or miles
and gallons).
Diagnostics
This function tells you the warnings,
the quantity of emergency fuel and
the GPS cover present at the time
consulted.
Note:
these warnings have previous
ly been displayed in the form of mes
sages and/or warning lights on the
control unit.
There are 6 categories of diagnostics :
engine diagnostics (warnings linked to the engine, gearbox
etc....),
brake diagnostics,
suspension diagnostics (warnings linked to the suspension, ESP
etc....),
wheel diagnostics (warnings linked to tyres),
door and window diagnostics,
passenger compartment diagnos tics. Distance to destination
When guidance is not activated, this
enables an approximate value to be
entered to make all the trip computer
calculations possible.
Specific features of the
monochrome screen CT and
the colour screen DT
General menu
Press the
"MENU"button to access
the general menu.
Select the icon ''Trip computer''
using the dial, then validate to
access the ''Trip computer'' menu.
The ''trip computer'' menu offers var
ious choices:
Trip computer configuration,
Diagnostics.
'Trip computer' context menu
The context menu associated with
the "Trip Computer" application
appears as a superimposed display
when the Trip Computer is the appli
cation currently being used in the
main screen window.
Briefly press the continuous applica
tion 'Trip computer' button to select
one of the following functions:
Warnings log,
Distance to destination.
18-11-2002