2002 PEUGEOT 807 engine

INSTRUMENTS AND CONTROLS
32
In zoneA,the temperature is correct.
In zone B, the temperature is too high. The central STOPwarning light and the
maximum coolant temperature warning light 1come on, accompanied by an
audible signal and the message "Coolant temp. too high"on the multifunction
display.
You must stop immediately.
Warning : wait for the engine to cool before topping up the le vel.
The cooling system is pressurised.
In the event of a breakdown and in order to avoid any risk of scalding, unscrew
the cap two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Instrument panel with
monochrome screen
Instrument panel with colour
screen
Coolant temperature indicator light
18-11-2002

Maximum
Minimum
Check the level with
the dipstick and top it
up.
The figure shown is
only correct if the vehicle has been
on stable, level ground, with the
engine stopped, for 10 minutes.
No oil
The message "Top
up the oil" appears
on the multifunction
display, accompa
nied by an audible signal.
It is essential to top up the oil to the
correct level, otherwise the engine
may be damaged.
Oil gauge fault
Flashing of the seg
ments indicates a
fault.
Check the level
using the dipstick.
Consult a PEUGEOT dealer. Control module display
After switching on the ignition, three
functions are shown in succession:
– service indicator (see correspond ing section),
– engine oil level indicator,
– total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for thirty seconds, when
the ignition is switched off, on open
ing the driver's door as well as on
locking and unlocking the vehicle.
It also displays the automatic gear
box positions and programmes
selected (see corresponding sec
tion).
Engine oil level
When the ignition is switched on, the
engine oil level is indicated for
approximately 10 seconds, after the
service information. Lighting rheostat
With the lights on,
press the button to
vary the intensity of
the lighting of the
control module, the
instrument panel, the
air conditioning dis
play and the multi–function display.
When the lighting reaches the mini
mum (or maximum) setting, release
it then press again to increase (or
reduce) the brightness.
As soon as the lighting is of the
brightness required, release the
button.
Trip recorder
zero reset
With the ignition on,
press the button.
INSTRUMENTS AND CONTROLS
34
18-11-2002

To make the setting on the passenger
side the same as that on the driver's
side :
– air conditioning with "MONO" but ton, press button A.
– air conditioning with "REAR" button, press button 2 or 3for more
than two seconds.
4 Adjustment of the airdistribution
 Pressing the correspond
ing button(s) 4directs the
flow of air to:
– the windscreen,
– the side vents and the central vents,
– the side vents, the central vents and the feet,
– the windscreen and the feet,
– the feet.
The indicator light corresponding to
the required direction 4comes on.
5 Adjustment of the rear ventilation
To enable the rear passengers to
YOUR 807 IN DETAIL 87
8 Demisting the rear
screen
 Press button 8, with the engine
running, to demist the rear screen
and the mirrors.
The demisting indicator light 8
comes on.
It switches off automatically after
approximately twelve minutes.  Pressing the button again switch
es it on again. If the engine is
switched off before the twelve
minutes have elapsed, demisting
will resume when the engine is
switched on again.
Note: it is possible to switch off the
demisting before it is switched off
automatically by pressing this button
again.
9 Comfort programme
This is the normal air condi
tioning system operating
mode.
 Press the "AUTO"button.
The system adjusts automatically to
the required value by switching on
the air conditioning.
It also controls the air distribution,
flow and intake so that there is suffi
cient air circulation in the passenger
compartment.
The "AUTO" symbol is displayed.
adjust the rear ventilation, press button
B
.
The rear ventilation symbol 5is
displayed.
The air flow adjustment controls 5for
the 2 nd
row side vents are operational.
To disarm the rear ventilation
controls, press button Bagain.
The rear ventilation symbol Bgoes
out.
6 Adjustment of the air flow
 Turn the adjument con
trol 6respectively to the
right or to the left to
increase or reduce the
flow of air.
The air flow symbol 6is filled in
according to the required value.
7 Air recirculation
Press this button to
recirculate the interior air.
The air recirculation symbol and
indicator light 7are displayed.
The recirculation isolates the passenger com
partment from outside smells and smoke.
Avoid prolonged operation in interior air
reciculation mode (risk of condensation
and deterioration of the air quality).  Pressing this button again returns the
system to automatic control of the air
intake.
18-11-2002

YOUR 807 IN DETAIL89
THE SEATS
Front seats with manual adjustment
1 Forwards/backwards adjustment
Lift the bar and slide the seat forwards or backwards.
2 Seat back angle adjustment Pull the lever upwards.
3 Driver's seat height adjustment Manoeuvre the handle upwards or downwards until the
desired position is reached.
4 Driver's seat lumbar adjustment Move the lever up or down to obtain the required posi
tion.
5 Head restraint height and angle adjustment To raise or lower the restraint, push it forwards, at the
same time sliding it.
The adjustment is correct when the upper edge
of the head restraint is level with the top of the
head.
To remove it, set it in the high position, lift the tab using
a coin and pull upwards and forwards at the same time.
To reinstall, engage the head restraint rods in the
holes, making sure they are aligned with the seat back.
Never drive with the head restraints removed; they
must be in place and correctly adjusted.
6 Rotating of seats Place the seat back in the upright position and move
the steering wheel forward. Place the seat in the middle position on the runner and at maximum height.
On the driver's side, apply the handbrake, then release,
pulling on the end.
Pull the control upwards and rotate the seat inwards.
This rotating operation must be carried out with the
engine switched off.
The passenger must not be facing the rear when the
vehicle is being driven.
18-11-2002

YOUR 807 IN DETAIL91
Memorising using the buttons M,
1 and 2
T
o memorise using the buttons located
on the side of the seat: Place the ignition key in the 'running'
position (2 nd
notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running Keep button 1 or 2pressed down
until the end of setting of the cor
responding memorised position.
Memorising seat and mirror
positions
Four driving positions can be memo
rised:
– two, using
two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front heated seat controls
The front seats can be heated sepa
rately.
Use the adjustment controls located
on the side of each seat to select the
level of heating required :
0:
Off.
1: Low.
2: Medium.
3: High.
The seat temperature is controlled
automatically.
Note: the heated seats only operate
with the engine running.
18-11-2002

YOUR 807 IN DETAIL
90
Front seats with electrical adjustment A Forwardsbackward
s adjustment
Push the control forwards or backwards to slide the seat.
B Driver's seat height adjustment Push the rear part of the control upwards or downwards to
obtain the required height.
C Seat back angle adjustment Tilt the control to the front or the rear to obtain the co rrect
angle.
D Driver's seat lumbar adjustment (mechanical) Raise or lower the lever to obtain the correct position.
E Head restraint height and angle adjustment To raise or lower the head restraint, pull forwards, at the
same time sliding it.
The setting is correct when the upper edge of the
head restraint is level with the top of the head.
To remove the head restraint, place it in the high position , lift
the tab using a coin and pull upwards and
forwards at the same time.
To reinstall, engage the head restraint rods in the holes,
making sure they are aligned with the seat back.
Never drive with the head restraints removed; they must be
in place and correctly adjusted.
F Rotating of seats (mechanical) Place the seat back in the upright position and move the
steering wheel forward.
Place the seat in the middle position on the runner andat maximum height.
On the driver's side, apply the handbrake, then release,
pulling on the end.
Pull the control upwards and rotate the seat inwards.
This rotating operation must be carried out with the engine
switched off.The passenger must not be facing the rear when the vehicle
is being driven.
Note: the electrical functions of the seats are cancelled one
minute after the ignition has been switched off.
18-11-2002

YOUR 807 IN DETAIL91
Memorising using the buttons M,
1 and 2
T
o memorise using the buttons located
on the side of the seat: Place the ignition key in the 'running'
position (2 nd
notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running Keep button 1 or 2pressed down
until the end of setting of the cor
responding memorised position.
Memorising seat and mirror
positions
Four driving positions can be memo
rised:
– two, using
two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front heated seat controls
The front seats can be heated sepa
rately.
Use the adjustment controls located
on the side of each seat to select the
level of heating required :
0:
Off.
1: Low.
2: Medium.
3: High.
The seat temperature is controlled
automatically.
Note: the heated seats only operate
with the engine running.
18-11-2002

Removing a seat
Fold the corresponding seat.
Grasp the two bars Gunder the seat
and tighten them securely.
The front anchorages unlock.
Lift the seat and carry it using the
carrying handle H.
Refitting a seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat.
Locate the front anchorages in the
slides (if necessary tighten the two
bars Gsecurely).
Tilt the folded seat towards the rear.
The rear anchorages lock.
Lift the seat back (for the centre seat,
move control E) Turning a seat round
The rear seats can be placed in the
'rearwards facing' position.
For this, after the seat has been fold
ed, carry out the removal and replac
ing operations for the seat and turn it
round.
YOUR 807 IN DETAIL
94
Table position of the centre seat
Place the head restraint in the low
position.
Push control Eupwards.
Tilt the seat back forwards.
You now have a table with two cup
holders.
Folding the centre seat
Place the seat in the table position.
Lift control F
Place the seat in the closed position. This turning operation
must be carried out with
the engine switched off.
It is prohibited to sit facing
the rear when the vehicle
is being driven.
Never use the adjusting straps to
remove, refit or transport a seat.
When the vehicle is being driven,
it is prohibited to place a side seat
in the closed position, when a
passenger is sitting in the 3rd row.
18-11-2002