2002 PEUGEOT 807 tow

YOUR 807 IN DETAIL83
This mode permits:
displaying of the vehicle on the map with the route proposed by
the navigation if the guidance is
active,
zooming in on the map in accor dance with the eleven preset
levels,
displaying of the "Navigation
Guidance" contextual menu.
"Vehicle following on map" mode
From the
general menu , the main
"Map" menu offers various options
for guidance management:
switching to "Selection Movement on map" mode**,
direction of the map towards the North or in the direction of the
vehicle,
recentering of the map around the vehicle when it has disappeared **,
opening of the services selection window visible on the map,
displaying of the window for enter ing the description for recording
the current position of the vehicle
in a directory file.
Map*The contextual menu associated
with the
"Map"application and with
the "Selection Movement on
map" mode appears as a superim
posed display, when these are in use
in the main screen window.
This menu is limited to the following
functions:
displaying of the information on the location selected on the map,
selection of a location on the map as a destination,
storing of the location selected (postal address if available or, if it
is not, GPS coordinates, so that
they can be recorded in a directory
file),
switching to "Vehicle following on map" mode.
* DT colour screen only.
** During the year.
"Map" contextual menu**
18-11-2002

YOUR 807 IN DETAIL
92
4 12V socket
You have a 12V accessory socket at
the foot of the driver's seat, which is
accessible to passengers in the
2
nd
row.
5 Front and rear armrests
To place the armrest in its rest
position:
– Lift the armrest until it is is aligned with the seat back.
To place the armrest in the position
in which it is used:
– Push it towards the rear.
– Fold it down completely.
– Raise it slowly to the required position.
– If you lift it past the required position, restart the above operations.
To remove it occasionally:
– Lift the armrest, going past the idle position.
– press its securing pin firmly and tilt it fully.
– Pull towards you to remove it from its fixing.
To put it back in place:
– place it in its removal position.
– Push as far as the fixing allows.
FRONT SEAT LAYOUT
1 Storage drawers
There is a storage drawer under
each front seat.
– To open it, lift and pull.
– To take it out, open it to its full
extent, press the ends of the slides
and lift it, then remove it complete
ly.
Note: under the seat on the passen
ger side, if the vehicle has an ampli
fier, it will not be possible to use the
storage drawer. 2 Retaining elastic straps
There is an elastic retaining strap on
each front seat, on the centre side.
– In the side position (elastic strap
on your own seat), this can be
used as a magazine holder.
– In the transverse position (elastic straps hooked between the two
seats), it can hold a bag.
3 'Aviation' type table
You have an 'aviation' type table fitted
with a can holder, fitted to each front
seat.
Do not forget to fold this before
pivoting the seat.
Note: each front seat also has a
pocket for money on the seat back
18-11-2002

YOUR 807 IN DETAIL93
THE REAR SEATS
Forwards/backwards
adjustment
Lift bar Aand slide the seat towards
the front or the rear.
From the third row you can pull on
strap B and slide the seat towards
the front.
This makes it easier for passengers
to exit the 3rd row of seats, when
folding down the second row seat.
Adjusting the angle of the seat
back
Push lever Cupwards and adjust the
angle as required.
Release the lever to lock.
Folding a side seat
Access to the third row:
Place the head restraint in the low
position.
Push control Cupwards as far as
possible.
Tilt the seat back towards the front
until the rear anchorages are
unlocked.
Fold the seat back onto the seat
cushion.
Place the seat in the closed position.
Exiting the third row:
Place the head restraint in the low
position.
Push control Dupwards as far as
possible.
Tilt the seat back towards the front
until the rear anchorages are
unlocked.
Fold the seat back onto the seat cushion.
Place the seat in the closed position. Table position of a side seat
Fold the corresponding seat.
Tilt the fold seat rearwards, until the
rear anchorages lock.
You now have a shelf with two cup
holders.
Folding a side seat from the table
position
Lift the seat back.
Fold as described opposite.
18-11-2002

Removing a seat
Fold the corresponding seat.
Grasp the two bars Gunder the seat
and tighten them securely.
The front anchorages unlock.
Lift the seat and carry it using the
carrying handle H.
Refitting a seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat.
Locate the front anchorages in the
slides (if necessary tighten the two
bars Gsecurely).
Tilt the folded seat towards the rear.
The rear anchorages lock.
Lift the seat back (for the centre seat,
move control E) Turning a seat round
The rear seats can be placed in the
'rearwards facing' position.
For this, after the seat has been fold
ed, carry out the removal and replac
ing operations for the seat and turn it
round.
YOUR 807 IN DETAIL
94
Table position of the centre seat
Place the head restraint in the low
position.
Push control Eupwards.
Tilt the seat back forwards.
You now have a table with two cup
holders.
Folding the centre seat
Place the seat in the table position.
Lift control F
Place the seat in the closed position. This turning operation
must be carried out with
the engine switched off.
It is prohibited to sit facing
the rear when the vehicle
is being driven.
Never use the adjusting straps to
remove, refit or transport a seat.
When the vehicle is being driven,
it is prohibited to place a side seat
in the closed position, when a
passenger is sitting in the 3rd row.
18-11-2002

THE REAR SEAT
Forwards/backwards
adjustment
Lift bar Aand slide the seat towards
the front or the rear.
Note: to make it easier to load the
vehicle through the tailgate, you can
pull on strap B and slide the seat for
wards. Rear parcel shelf position
Place the head restraints in the low
position.
Push control
Cupwards, from the
tailgate.
Tilt the seat back on the seat
cushion.
Folding the seat
Place the head restraints in the low
position.
Push control Cupwards, from the
tailgate.
Fold the seat back onto the seat
cushion.
Pull on strap Dto unlock the rear
anchorages.
Place the seat in the closed position.
When driving, attach the retaining
straps to the handles. Removing the seat
Fold down the seat.
Grasp the two bars
Eunderneath the
seat.
The front anchorages unlock.
Note: for removal and refitting, pass
the rear seat, in the "folded" position,
through the sliding side doors.
Refitting the seat
Check that there is nothing block
ing the runners which could pre
vet corrrect locking of the seat
anchorages.
Position the front anchorages at the
front stop of the runners.
Tilt the folded seat rearwards.
The rear anchorages then lock.
Unlock the seat back using control C
and pull it up using the strap.
YOUR 807 IN DETAIL 95
Never use the adjustment
straps to remove, refit or
transport the seat.
18-11-2002

YOUR 807 IN DETAIL109
T
ailgate release
This enables the tailgate to be
unlocked in the event of a central
locking fault.  Fold back a 2 nd
row rear seat,
 Fold back a 3 rd
row rear seat or
the bench seat to gain access to
the lock from inside the boot,
 Insert a small screwdriver into
hole Ain the lock and push it
towards the left to unlock the
tailgate .
TAILGATE
Simultaneous locking or unlock
ing of the tailgate and the doors
The tailgate is locked or unlocked by
the remote control or the driver's
door or passenger door lock.
To open, operate the handle
Aand
lift the tailgate.
Note: The tailgate locks automatical
ly when the vehicle is being driven at
more than 6 mph (10 km/h) and
unlocks when one of the doors is
opened.
"Tailgate open" warning
When the engine is running or the
vehicle is being driven, you are
warned if the tailgate is not closed
correctly by a diagram on the
multi–function display, accompanied
by an audible signal. Partially opening rear
windows
To partially open the rear windows,
tilt the lever
Aand push it fully to
lock the windows in the open posi
tion.
18-11-2002

Direction indicators
(flashers)Left:downwards.
Right: upwards.
YOUR 807 IN DETAIL
112
LIGHTING CONTROL
Front and rear lights
Selection is by turning ring
A.
Lights off
Side lights on Dipped beam/Main
beam
Automatic switching
on of lights Dipped beam/main beam change
Pull the stalk fully towards you.
Lightson buzzer
When the ignition is switched off,
when the driver's door or front pas
senger door is opened, a buzzer
sounds, accompanied by the mes
sage
"Side lights on" on the
multi–function display if you have left
your lights on.
Front and rear fog lights
Rotate ring Bforwards to switch on
and rearwards to switch off. The sta
tus is confirmed by the light on the
instrument panel.
Front fog lights (1 st
rotation
of the ring forwards)
These operate with the side lights
and the dipped beam headlamps. Front and rear fog
lights (2nd
rotation of
the ring forwards) These operate with the side lights
and the dipped beam headlamps.
Note:
to switch off the front and rear
fog lights, turn the ring rearwards
twice in succession.
In clear weather or in
rain, both day and night,
rear fog lights dazzle and
are prohibited.
Do not forget to switch
them off when they are no longer
needed.
Automatic switching on of the
lights switches off the rear fog
lamps, but the front fog lamps
remain on.
18-11-2002

YOUR 807 IN DETAIL
114
WINDSCREEN WIPER STALK
Front windscreen wiper stalk with
intermittent wipe
2 Fast wipe
(heavy rain).
1 Normal wipe
(moderate rain).
l Intermittent wipe.
0 Off.
Single wipe
(press downwards). Front windscreen wiper stalk with
automatic wipe
2 Fast wipe
(heavy rain).
1 Normal wipe
(moderate rain).
AUTO Automatic wipe.
0 Off.
Single wipe
(press downwards). Operation
In position
1or 2, when the vehicle
stops, the windscreen wiper
changes to a lower wiping speed,
then resumes its initial speed when
the vehicle starts again.
In the Intermittent position, the wip
ing speed is proportional to the
speed of the vehicle.
In the AUTOposition, the wiping
speed is proportional to the heavi
ness of the rain.
When the ignition has been
switched off for more than one
minute with the stalk in the wipe
position, it is necesary to reacti
vate this function. To do this, move
the stalk to any position, then move
it back to the required position.
Windscreen and headlamp wash
Pull the windscreen wiper stalk
towards you.
The windscreen wash then the wind
screen wipers operate for a fixed
period.
The windscreen wash and headlamp
wash operate simultaneously for a
few seconds, only if the dipped
beam or main beam headlamps
are on.
18-11-2002