2002 PEUGEOT 807 fog light

YOUR 807 AT A GLANCE10STEERING WHEEL STALKS
LIGHTING
Front and rear lights (ring A)Lights off.
Side lights on.Dipped / main
beam headlamps
on.
Automatic
switching on of
lights. Automatic switching on of
lights
To activate or disarm this func
tion, place the key in the acces
sories position, the lighting stalk
in position
0 and press for more
than two seconds on the end of
the stalk.
Front fog lamps and rear fog
lamps (ring B)
Front fog lamps (1 st
rota
tion of the ring forwards).
Front fog lamps
and rear fog
lamps (2 nd
rotation
of the ring for
wards).
To switch off: rotate the push ring
B rearwards. WINDSCREEN WIPERS
Front
2 Rapid wipe
1 Normal wipe
l Intermittent wipe
or
AUTO Automatic wipe
0 Stop
Single wipe
Washwipe: pull the stalk towards you.
Automatic wipe
In the AUTO position, a
rain sensor controls the
automatic operation of
the wipers. The wipers
adapt their speed to
the intensity of the
rainfall.
Rear
Stop Intermittent W ash
wipe wipe
11 2
11 4
18-11-2002

26
PETROL / DIESEL CONTROL MODULE
1 Dipped beam headlamps indi
cator light.
2 Main beam headlamps indicator
light.
3 Lefthand direction indicator.
4 Service indicator, oil level
indicator, automatic gearbox
indicator* and total distance
recorder.
5 Front fog lamps indicator light. 6
Righthand direction indicator.
7 Dynamic stability control
ASR/ESP indicator light.
8 Rear fog lamps indicator light.
9 ABS system warning light.
10 Engine diagnostics warning
light.
11 Cruise control indicator light.
12 Lighting rheostat. 13
Handbrake, brake fluid level
and electronic brake force
distribution warning light.
14 Engine oil pressure warning
light.
15 Central (STOP) warning light.
16 Battery charge warning light.
17 Diesel engine preheating
indicator light.
18 Trip recorder zero reset.
19 Driver's seat belt warning light.
20 Passenger air bag disarming
indicator light.
21 Front, side and curtain air bags
warning light.
* According to specification.
INSTRUMENTS AND CONTROLS
18-11-2002

Direction indicators
(flashers)Left:downwards.
Right: upwards.
YOUR 807 IN DETAIL
112
LIGHTING CONTROL
Front and rear lights
Selection is by turning ring
A.
Lights off
Side lights on Dipped beam/Main
beam
Automatic switching
on of lights Dipped beam/main beam change
Pull the stalk fully towards you.
Lightson buzzer
When the ignition is switched off,
when the driver's door or front pas
senger door is opened, a buzzer
sounds, accompanied by the mes
sage
"Side lights on" on the
multi–function display if you have left
your lights on.
Front and rear fog lights
Rotate ring Bforwards to switch on
and rearwards to switch off. The sta
tus is confirmed by the light on the
instrument panel.
Front fog lights (1 st
rotation
of the ring forwards)
These operate with the side lights
and the dipped beam headlamps. Front and rear fog
lights (2nd
rotation of
the ring forwards) These operate with the side lights
and the dipped beam headlamps.
Note:
to switch off the front and rear
fog lights, turn the ring rearwards
twice in succession.
In clear weather or in
rain, both day and night,
rear fog lights dazzle and
are prohibited.
Do not forget to switch
them off when they are no longer
needed.
Automatic switching on of the
lights switches off the rear fog
lamps, but the front fog lamps
remain on.
18-11-2002

AUTOMATIC SWITCHING ON
OF LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off when the light
becomes bright enough or the wind
screen wipers stop.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. As a consequence, the lights
will not come on automatically.
This function is active when the
vehicle is supplied to the customer.
To disarm or activate the function :  Start with the key in the acces
sories position (1st notch),
 Place the lights stalk in position 0,
 Press the end of the stalk for more
than two seconds.
Note: after the ignition is switched off
and depending on the brightness,
the lights remain on for approximate
ly 45 seconds or until the vehicle is
locked.
Do not cover the brightness sen
sor located in the centre of the
fascia. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting
active" on the multi–function dis
play .
Disarming
Disarming of the function is accom
panied by an audible signal.
Note: the function is disarmed
temporarily when the driver uses the
manual lighting controls.
YOUR 807 IN DETAIL 113
18-11-2002

PRACTICAL INFORMATION
144
CHANGING A BULB
Front lights
Note:
handle the bulbs with a dry cloth.
1 Dipped beam headlamps: H755W or xenon bulb.
2 Main beam headlamps: H755W or xenon bulb.
3 Fog lamps: H155W.
Note : make access on the righthand side easier by remo
ving the fuse box cover.
Turn the protective cover corresponding to the faul
ty bulb a quarter of a turn and remove it.
 Disconnect the connector.
 Press the end of the securing clip to free it. Change
the bulb. When fitting the new bulb, ensure that the
direction notches are positioned correctly and the
securing clip is fixed properly.
 Reconnect the connector.
 Refit the protective cover, then turn it a quarter of a
turn to the right. The headlamps are fitted with polycarbonate glass with a
protective coating.
Do not clean them with a dry or abra
sive cloth, nor with a detergent or solvent product. Use
a sponge and soapy water.
4 Side lights: W 5 W.
 Push the light from the inside towards the outside of
the bumper.
 Pull the light forwards.
 Turn the bulb holder a quarter turn to the left and
remove it.
 Turn the bulb a quarter turn to the left, remove it and
change it.
When refitting, engage the light towards the outsi
de and move it towards the inside of the bumper.
5 Direction indicators: PY 21 W (amber).F
 Turn the bulb holder a quarter of a turn to the left
and remove it.
 Change the bulb.
Note: In certain climatic conditions (low temperature,
humidity), condensation inside the headlamp glass is
normal ; it disappears a few minutes after the lights are
switched on.
WARNING: RISK OF ELECTROCUTION
Xenon bulbs must be changed by a PEUGEOT dealer.
18-11-2002

Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
 Hold the connector and turn the
bulb holder a quarter turn to the
left.
 Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle:  open the tailgate,
 remove the air extraction grille on
the side concerned,
 unclip the light harness,
 unscrew the two interior nuts and
remove the light,
 unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
 unscrew the faulty bulb an eighth
turn to the left and change it. When refitting: 
take care to position the bulb cor
rectly and press on it to engage it,
 take care to position the bulb hol
der correctly and press on it to
engage it,
 take care to position and secure
the light correctly.
Number plate lights:
W 5 W  Remove the lens.
 Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs.  Remove the tailgate upper trim by
unclipping it on either side.
 Squeeze the two tabs 1to release
the bulb holder.
 Change the faulty bulb.
 When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002

Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
 Hold the connector and turn the
bulb holder a quarter turn to the
left.
 Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle:  open the tailgate,
 remove the air extraction grille on
the side concerned,
 unclip the light harness,
 unscrew the two interior nuts and
remove the light,
 unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
 unscrew the faulty bulb an eighth
turn to the left and change it. When refitting: 
take care to position the bulb cor
rectly and press on it to engage it,
 take care to position the bulb hol
der correctly and press on it to
engage it,
 take care to position and secure
the light correctly.
Number plate lights:
W 5 W  Remove the lens.
 Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs.  Remove the tailgate upper trim by
unclipping it on either side.
 Squeeze the two tabs 1to release
the bulb holder.
 Change the faulty bulb.
 When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002

PRACTICAL INFORMATION
146
Fuse n
o
. Rating Functions
1 10 A Rear fog lamp.
2 15 A Rear screen wiper.
4 15 A Supply to functions via the builtin systems interface.
5 10 A Left brake light.
7 20 A Map readers Lighter Passenger lower glove box
lighting Electrochrome interior mirror .
Fascia panel fuses
 Unscrew the bolt a quarter of a
turn with a coin, then pull the
handle to open the cover and
access the fuses.CHANGING A FUSE
The fuse boxes are located under
the fascia (driver's side), in the batte
ry compartment (floor, driver's side)
and in the engine compartment.
The spare fuses and special pliers A
are fixed to the inside of the lid of the
instrument panel fuse box.
Removing and changing a
fuse
Before changing a fuse you must
establish the cause of the fault and
have it corrected. The fuse numbers
are indicated on the fuse box.
 Use the special pliers A.
Always change a faulty fuse for
one of the same rating.
Correct Incorrect
Pliers A
18-11-2002