2002 Peugeot 607 Dag light

INSTRUMENTS AND CONTROLS39
Automatic gearbox selector lever position indicator ligh
ts
'Park' indicator lights
'Reverse' indicator lights
'Neutral' indicator lights
'Drive' indicator lights
Note: the letter Sand the symbol
linked to the above indicator lights correspond respectively to t he Sport and Snow oper
ating programmes.
'Manual' indicator lights
These indicator lights correspond to the four manually operated gears.

Trip recorder
zero reset
With the ignition on, press
the button.
Manual operation
With the headlamps on, press button
B to increase the brightness of the
instrument panel lighting or button A
to reduce it.
As soon as the lighting reaches the
required level of brightness, release
the button.
INSTRUMENTS AND CONTROLS 41
Illumination
buttons
Automatic operation
The degree of illumination of the
instrument panel automatically
adapts to the external brightness.
By day , the setting cannot be altered.
At night, the brightness can be
increased by means of button B.
A Peugeot dealer is able to cancel
automatic operation if you prefer
manual operation.

Changing the colours
Select the desired colour, then confirm.
If required, select 'automatic
day/night' , then confirm and record
the changes.
Note: this function allows the system
to change automatically to 'Night'
colour when the vehicle lights are on.
Changing the brightness
Select the 'Brightness' function,
then confirm:
– turn the dial clockwise to increase,
– turn the dial anticlockwise to decrease.
Record the modifications.
Note: this function allows only limit
ed adjustment of the brightness,
since the screen lighting is depen
dent on the sunshine/brightness sen
sor in the vehicle.
YOUR 607 IN DETAIL 45
Insert the software CDRom into the
drive in place of the map CDRom.
After a few moments, the mesage
"Warning Reprogramming Sequence"
then the message "Navigation applica
tion Processing" apears, together with
a progress bar.
When the message "Software Loading
End Eject CD" appears, eject the
software CDRom and insert the map
CDRom into the drive.
Check that the CDRom has loaded
correctly (see paragraph "Voice syn
thesis adjustment" in the chapter enti
tled "The satellite navigation system
with colour screen").

YOUR 607 IN DETAIL59
CASSETTE: Audio RM2
Selecting cassette mode When a cassette is inserted, the cassette player will start auto matically.
If a cassette is already inserted, press button C.
Ejecting the cassette Press button Eto eject the cassette from the drive.
Direction of play
The player will play sides 1 and 2 of the cassette alternate ly, automatically reversing the direction of play at the end of the side.To manually reverse the direction of play of the cassette, press b utton C.
Selecting a cassette track (blank search) Press button Mto select the next track.
Press button Lto return to the start of the current track or to select the previ ous track.
Fast forward and rewind
Fully press button Mor Lto fast forward or rewind the tape. At the end of the fast forward/rewind, the current side is played.
Noise reduction (Dolby B NR system) Press button Cfor more than 2 seconds to switch the function on or off.
Dolby noise reduction is manufactured under licence by Dolby Lab oratories Licensing Corporation.
'Dolby' and the double D symbol are brand marks of Dolby Labora tories Licensing Corporation.
Recommendations concerning the use of cassettes
– Use good quality cassettes.
– Avoid the use of cassettes which play for more than 90 minute s.
– Never expose cassettes to heat or sunlight.
– Retension the tape if necessary before inserting the cassette into the player.
– Regularly clean the playing heads with a damptype cleanin g cassette.

TELEPHONE: Audio/Telephone RT2
This function is a GSM 900 MHZ telephone incorporated in the audio system.
It possesses a 'hands free'function, provided by a microphone located in the front courte sy light and a steering column
remote control which allows access to most of the functions.
It also possesses a 'confidential' function, provided by the instrument panel located in the u pper casing of the centre front
armrest.
Note: An echo may be heard for a few seconds at the beginning of t he call.
The principal "mobile"type functions are shown on the display incorporated in the a udio system; the menu lists can be
referrred to on the multifunction display.
This function is active when the ignition key is in the accessories position (1st notch), the ignition is switched on (2nd notch),
the engine is running or the vehicle is being driven.
Note: when the ignition key is in the accessories position (1st notch) or the ignition is switched on (2nd notch), this function
will be interrupted after thirty minutes, when the message 'Economy mode active'appears on the multifunction display. If
you are using the telephone at that time, you will be ab le to finish your call.
General information about the display (Audio/Telephone R T2 display)
In telephone mode, the display shows the following informa tion, where applicable.
1. Network signal indicator (3 levels).
2. Service indicator not available.
3. Indicates a communication in progress.
4. Indicator showing connection to an outside network.
5. Indicates:
– when continuously lit: presence of an unread message or message s.
– when flashing: the message tape is full.
6. Display zone (10 symbols x 2 lines).
YOUR 607 IN DETAIL
62

The CDROM drive
This is located on the left hand side of the boot. Open the
panel to access it.
1. Ejection button of the CDROM.
2. CDROM housing.
3. The CD indicator light shows the presence of a CDROM
in the drive.
72
YOUR 607 IN DETAILThe last voice message and route change recall
control.
A brief press on the button on
the end of the lights stalk
repeats the last voice infor
mation.
Press for more than two sec
onds to make a route change.
The CD–ROM This contains all the map
data.
It must be inserted in the
drive, printed face upwards.
With the colour screen, you have a second CDROM (soft
ware) containing the voice synthesis software and lan
guages.
The use of blank compact discs may cause
malfunctions.

YOUR 607 IN DETAIL
90
1 Driver's side
adjustment
2 Passenger's side adjustment
The required value is
displayed (from 15 to
30: comfort value = 22).
 Press the corresponding top and
bottom arrows to adjust.
3 Driver comfortprogramme
4 Passenger comfort
programme
 Press the 'AUTO'button(s).
The system adjusts automatically to
the required value .
It also controls the air distribution,
flow and intake so that there is suffi
cient air circulation in the passenger
compartment.
The air flow (fan) symbol and the
'AUTO' symbols are displayed.
Note: when programme 5or function
11 (following pages) are being used,
the 'AUTO' passenger button does
not operate; it causes temporary
flashing of button 5or 11 indicator
light.
AUTOMATIC AIR CONDITIONING
Located on the centre console, the control panel is between
the multifunction
display and the audio system.
The driver and front passenger can each adjust the temperature a nd the air dis
tribution, to suit their requirements.
Do not cover the sunshine / brightness sensor located i n the centre of the
fascia. It helps to regulate the air conditioning, automati c switching on of
the lights and the automatic adjustment of the instrument pane l bright
ness.

YOUR 607 IN DETAIL91
Manual adjustment Y
ou may, if you wish, make a differ
ent selection from the one offered by
the system, by manually modifying a
setting.
 Pressing the 'AUTO'driver or
passenger button enables you to
return to the corresponding auto
matic operation.
6 Adjustment ofthe driver's air
distribution
7 Adjustment of the passenger's
air distribution
 Pressing the dri
ver's or passenger's
button several times in
succession allows you to position the
air flow on the driver's or passen
ger's side, towards:
– the windscreen and the feet,
– the feet,
– the centre vent, the side ventand the feet,
– the centre vent and the side vent,
– the windscreen. Note:
when programme 5(following
page) is being used, button 7does
not operate; it causes temporary
flashing of the button 5indicator
light.
8 Air conditioning (A/C) on/off
 Press this button
once to stop the air
conditioning.
The symbol 'A/C'goes out.
 Press this button again to return to
automatic air conditioning.
The symbol 'A/C' comes on.
5 Visibility
programme
In certain cases, the
comfort programme
may prove inadequate
to demist or deice the
windows (humidity,
many passengers, ice).
 In this situation, select the visibili
ty programme for rapid clearing of
the windows.
It manages the air conditioning and
the air flow and intake and distrib
utes the ventilation towards the
windscreen and the side windows.
The symbols 'A/C', 'AUTO' and air
flow (fan) are displayed.
Note: for your comfort, between two
starting operations the settings are
retained if the temperature of the
passenger compartment has not var
ied a great deal. If it has, automatic
mode is used.