2002 Peugeot 406 Break Owner's Manual

RADIO Notes on radio reception
Car radio receivers are subject to phenomena which do not affect domestic radio sets. Both MW/LW and FM reception are
subject to various forms of interference. This is no reflection on the quality of the equipment, but is due to the nature of the
signals and the way in which they are transmitted.
On MW/LW, interference may be noticed when passing under high voltage power lines or bridges, or in tunnels.
On FM, interference may be the result of increasing distance from the transmitter, deflection of the signals by obstacles
(mountains, hills, buildings etc), or of being in an area which is not covered by a transmitter. Selecting radio mode
Press button B.
Selecting a waveband Briefly press button Bto select the FM1, FM2, Fmast and AM wavebands.
Automatic station search Briefly press button K or Lto search for the station immediately above or below.
By continuing to press the button in the direction selected, you will obtain contin-
uous scrolling of the frequency. The scrolling stops at the first station found as soon as the button is released.
If the TAtraffic programme is selected, only stations broadcasting this type of programme are selected.
Searching for a station occurs first in " LO" sensitivity (selection of the most powerful transmitters) during scanning of the
waveband, then in " DX" sensitivity (selection of the weakest and most distant transmitters).
To make a direct search in " DX" sensitivity, press button Kor Ltwice.
YOUR 406 IN DETAIL
78

Manual station searchPress the "MAN" button.
Briefly press button Kor Lto increase or decrease the frequency displayed.
By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency. The scrolling stops at the first station found as soon as the button is released.Pressing the " MAN" button again returns you to automatic station search.
Manual storing of stations in the memory Select the station required.Press one of the buttons "1" to " 6" for more than two seconds.
The sound stops then becomes audible again, confirming that the station has been stored in the memory. Automatic storing of FM stations in the memory (autostore) Press button B for more than two seconds, to automatically store the 6 stations with the strongest signal in
FM. These stations are stored in the FMast waveband.
-If it is not possible to find 6 stations, the remaining memories are empty.
Recalling stations stored in the memory For each waveband, briefly press buttons " 1" to " 6" to recall the corresponding station.
The list of the 6 stations stored in memory on the waveband is displayed each time one of the buttons " 1" to " 6" is pressed.
YOUR 406 IN DETAIL 79

RDS Using the RDS (Radio Data System) function on FMRadio Data System allows you to continue listening to the same station, whatever frequency it is using for the region you are going through. Briefly press the " RDS" button to switch the function on or off;
the display will show:
-"RDS" if the function is selected.
-"(RDS)" if the function is selected but not available.
RDS station following
The display indicates the name of the station selected. The radio is continually searching for the station which has the best reception and which is transmitting the same programme.
Traffic information programme Press the "TA" button to switch the function on or off.
The display will show:
-" TA " if the function is selected,
-"(TA)" if the function is selected but not available.
Any traffic information flash will be given priority, whatever source you are listening to (radio, cassette or CD changer). If you wish to interrupt a message, press the " TA" button; this switches the function off.
Note: the volume of traffic information announcements is independent of the volume of normal radio listening. You can adjust it using the volume button. The setting will be stored and will be used when the next messages arebroadcast.
YOUR 406 IN DETAIL
80

Regional following modeWhen they are part of a network, certain stations broadcast regional programmes in the various areas they serve. With regional following mode you can keep listening to the same programme. Press the "RDS" button for more than two seconds to switch the function on or off.
PTY function This allows you to listen to stations broadcasting a specific type of programme (news, culture, sport, rock etc.).With FM selected, press the " TA" button for two seconds to switch this function on or off.
To search for a PTYprogramme:
-select the PTYfunction,
-briefly press button Kor Lto scroll down the list of the various types of pro-
grammes offered.
-when the programme of your choice is displayed, keep button Kor Lpressed for two seconds to carry out an automatic
search (after an automatic search the PTYfunction is switched off).
In PTY mode the different types of programmes can be stored in the
memory. To do this, press the preselection buttons " 1" to " 6" for more
than two seconds.
To recall the type of programme stored in the memory, briefly press the corresponding button.
EON system
This connects stations which are part of the same network. It enables the broadcast of traffic information by a station, which is part of the same network as the station to which you are listening.
This service is available when you have selected the TA traffic information programme or the PTYfunction.
YOUR 406 IN DETAIL 81

CASSETTE Selecting cassette modeWhen a cassette is inserted, the cassette player will start automatically. If a cassette is already inserted, press button C.
Ejecting the cassette Press button Eto eject the cassette from the player.
Direction of play
The player will play sides 1 and 2 of the cassette alternately, by automatically reversing the direction of play at the end of a
side. To manually reverse the direction of play, press button C.
Selecting a track on a cassette (blank search)
Press button Kto select the next track.
Press button Lto return to the start of the current track or to select the previous
track.
Fast forward/rewind Fully press button K or Lto fast forward or rewind the cassette. At the end of the fast forward/rewind, the set plays the cur-
rent side. Noise reduction (Dolby B NR system) Press button Cfor more than two seconds to switch the function on or off.
Dolby noise reduction manufactured under licence from Dolby Laboratories Licensing Corporation. Dolby and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. Recommendations concerning the use of cassettes
-Use good quality cassettes.
-Avoid using cassettes which play for longer than 90 minutes.
-Never expose the cassettes to heat or direct sunlight.
-Re-tension the tape if necessary before inseting it into the player.
-Clean the playing heads regularly with a humid type cleaning tape.
YOUR 406 IN DETAIL
82

YOUR 406 IN DETAIL83
CD CHANGER Selecting CD changer mode Press button D.
Selecting a disc Press buttons "1" to " 6" to select the corresponding disc.
Selecting a track Press button Kto select the next track.
Press button Lto return to the start of the current track or to select the previous
track.
Accelerated play Press and hold button Kor Lfor forwards or backwards accelerated play.
Accelerated play stops as soon as the button is released. Shuffle
When the CD changer is selected, keep button " D" pressed for two seconds. The tracks will be played in ran-
dom sequence. Pressing button " D" again for two seconds returns you to normal play.

YOUR 406 IN DETAIL
84
This is located inside the boot on the left hand side. It holds up to 6 discs.
To insert a disc into the changer:
-open sliding panel A,
-press button Bto eject the cartridge C,
-open one of the six compartments of the cartridge by pulling tab D,
-insert the disc with the printed face upwards and close the compartment,
-insert the cartridge into the changer,
-close the sliding panel A.
RM2 CD CHANGER
The use of blank compact discs can cause malfunctions.

406 Saloon AUDIO SYSTEM (RM2) Presentation
Your 406 saloon is fitted with a JBL Audio Hi-Fi system, designed specifically for the passenger compartment. At the heart of the system, a 240 watt multifunction amplifier (1) (located in the boot) independently controls 10 high acoustic definition speakers. These speakers provide optimal reproduction and distribution of the sound in the vehicle, both in the front and the
rear. The speakers are situated:– in the fascia: two Micro Tweeters (3) set into two Mediums (4) for reproduction of the sound in the front.
– in the front doors: two Woofers (2) for reproduction of bass frequencies in the front.
– on the rear parcel shelf: two Tweeters (5) for reproduction of treble (high frequencies) in the rear are set into two ellipti-
cal speakers (6), which are adjusted to reproduce a very wide range of bass and ultra-bass frequencies throughout the
whole of the passenger compartment. You will appreciate the clarity and depth and notice that the sound fills the
whole of the vehicle perfectly.
Adjusting in CD modeThe basic functions remain those of the audio set.
There is no need for any further adjustment. However, in order to take
full advantage of your JBL audio system, you are advised to set theAUDIO functions (BASS, TREB, FAD, BAL) to position "0"(zero) and
the Loudness (LOUD)to the "ON" position.
YOUR 406 IN DETAIL 85