2002 Peugeot 307 SW Dag Owner's Manual

Only use products appro-
ved by Automobiles
PEUGEOT.
To ensure best perfor- mance from components
as important as the power stee-ring and the braking system, PEUGEOT selects and offersquite specific products.
CHECKS Battery
At the start of winter, have your bat-
tery checked by a PEUGEOT dealer. Air filter and pollen filter Have the filter elements replaced
regularly. If you drive in dusty
conditions, change them twice asoften. Brake pads Brake pad wear depends on the style of driving, in particular for vehicleswhich are used in town, over shortdistances. It may be necessary tocheck the thickness of the pads,even between services. Handbrake Where the handbrake travel is too great or there is a reduction in theperformance of the system, thehandbrake should be adjusted, evenbetween services. Have the system checked by a
PEUGEOT dealer. Manual gearbox This does not need an oil change. Check the level, according to themanufacturer's servicing schedule. Automatic gearbox This does not need an oil change. Have the level checked by a
PEUGEOT dealer, according to themanufacturer's servicing schedule. Oil filter
Change the filter regularly, in accor- dance with the servicing schedule.
RUNNING OUT OF FUEL (DIESEL) If you should run out of fuel, it is necessary to re-prime the circuit:
- fill the fuel tank with at least five
litres of diesel,
- operate the manual re-priming pump, until you feel resistance during the manoeuvre,
- operate the starter until the engine starts.
PRACTICAL INFORMATION
106

CHANGING A WHEEL
Tools The following tools are located:
Ð in the right-hand trim of the boot,1 - Wheelbrace.
2 - Removable towing eye.
3 - Socket for anti-theft bolts.
Ð in the holder in the centre of the spare wheel, 4 - Jack with handle.
5 - Bolt "covers" tools.
6 - Centralising tool.
7 - Removable chock. Parking the vehicle
As far as possible, park the vehicle on level, stable and non-slippery ground.
Apply the handbrake, engagefirst or reverse gear (position P
for the automatic gearbox) and
switch off the ignition. Access to the spare wheel
Open the boot.
Open the flap using the lug to release the winch and gainaccess to its control nut.
Unscrew the nut fully, using thewheelbrace 1, to unroll the winch
cable.
PRACTICAL INFORMATION 107

Place the jack 4in contact with
one of the four locating points A
on the sub-frame, the one which is closest to the wheel to bechanged.
Extend the jack 4until its base is
in contact with the ground.Ensure that the centre line of thebase of the jack is straight abovethe locating point A.
Raise the vehicle
Remove one bolt and install thecentralising tool 5in its place.
Unscrew the other bolts andremove the wheel.
PRACTICAL INFORMATION
108

Detach the wheel/holder assem- bly from the rear of the vehicle.
Take out the notched hook torelease the wheel, as shown inthe illustration.
Removing the wheel Slide the holder cover to gain access to the tools.
Place the chock 7under the
wheel diagonally opposite to theone to be changed.
Remove the trim, using thewheelbrace 1, pulling at the
valve passage hole (for vehiclesfitted with steel wheels).
Loosen the wheel bolts (see ¤"Special features of alloywheels" for vehicles fitted withalloy wheels). Note: you can use the other end
of the tool 6to unscrew the
wheel bolts.

PRACTICAL INFORMATION109
For your safety, always change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- with first or reverse gear enga- ged (position Pfor the automatic
gearbox),
- with the vehicle chocked. Never go underneath a vehicle that is supported only by a jack(use a ramp) Never refit the holder under the vehicle without the spare wheel. After changing the wheel:
- have the correct positioning of the punctured wheel, the tighte- ning of the bolts and the tyrepressure checked by a PEUGEOT dealer as soon aspossible.
- have the punctured tyre repai- red and refit it to the vehicle assoon as possible.
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.

Store the rest of the tools in theright-hand trim of the boot.
Fitting a wheel
Position the wheel using the cen- tralising tool 5to assist you.
Tighten the bolts by hand andremove the centralising tool 5.
Partly tighten the bolts using thewheelbrace 1.
Fold the jack 4and remove it.
Fully tighten the bolts using thewheelbrace 1.
Replace the wheel trim, startingby placing the wheel trim notchopposite the valve, and press iton using the palm of the hand.
Put the corresponding tools in the
holder and secure its cover.
Place the holder on the groundand align the spare wheel on it.
Pass the notched hook into the
holder cover.
Refit the wheel under the vehicletightening the winch control nutusing the wheelbrace 1.
Fully tighten and check that the
wheel is horizontally flush
against the rear floor.
Close the flap using the lug tolock the winch.

Special features of alloy wheels Bolt coversAlloy wheel bolts are covered by chrome trims. Use tool 6to remove the trims befo-
re slackening the bolts. Fitting the spare wheel If your vehicle is fitted with a steel spare wheel, when fitting it, it is normal
, when tightening the bolts, to
notice that the washers do not come
into contact with the rim. The sparewheel is secured by the cone shapeof each bolt. Fitting snow tyres If you fit snow tyres mounted on steel wheels, it is essential to use special
bolts available from your PEUGEOT
dealer. Anti-theft bolts* If your wheels are fitted with an anti- theft bolt (one per wheel), the chro-me trim and then the plastic covermust be removed using tool
6, befo-
re unscrewing the bolt using one ofthe two anti-theft sockets (whichwere given to you on delivery of yourvehicle along with the duplicate keysand the confidential card) and thewheel brace 1.
Note : make a careful note of the
code number engraved on the head
of the anti-theft socket. This willenable you to obtain duplicate anti-
theft sockets from a PEUGEOT dealer.
* According to model and country
PRACTICAL INFORMATION
110

CHANGING A BULB Front lights Note: on the right side, remove the style cover, fixed with
two plastic screws, to access the bulbs. Handle the bulbs with a dry cloth.
1 - Dipped beam headlamps: (H7-55W),
2 - Main beam headlamps: (H1-55W),
3 - Front fog lamps (H1-55 W). Turn the protective cover corresponding to the faulty bulb a quarter of a turn and remove it.
Disconnect the connector.
Press the end of the securing clip to free it. Changethe bulb. When fitting the new bulb, ensure that the direction notches are positioned correctly and the securing clip
is fixed properly.
Reconnect the connector.
Refit the protective cover, positioning it with the arrowupwards, then turn it a quarter of a turn to the right. The headlamps are fitted with polycarbonate glass with aprotective coating.
Do not clean them with a dry or
abrasive cloth, nor with a detergent or solvent pro-duct. Use a sponge and soapy water.
4 - Side lights: (W 5 W). Pull the socket rearwards, remove the bulb and change it.
5 - Direction indicators: (PY 21 W amber). Turn the bulb holder a quarter of a turn and remove it.
Change the bulb.
Note: In certain climatic conditions (low temperature,
humidity), condensation inside the headlamp glass is
normal ; it disappears a few minutes after the lights are
switched on.
PRACTICAL INFORMATION 111

Direction indicator repeaters:
(WY 5W amber). Push the repeater forwards and
release the assembly.
Hold the connector and turn thelens a quarter turn.
Change the bulb.
PRACTICAL INFORMATION
112
Amber coloured bulbs (direction indicators andside repeaters), must bechanged for bulbs ofidentical specification and
colour.

PRACTICAL INFORMATION113
Third brake light: 4 W 5 W bulbs. Remove the tailgate upper trim carefully by unclipping it on eitherside, perpendicular to its direc-tion of engagement.
Insert a screwdriver into the twoouter holes Bto press on the two
tabs C.
Push the light unit outwards whilemaintaining the pressure on thetabs.
Pull the light unit outwards whiletilting it.
Change the faulty bulb.
When refitting, ensure that thelight unit tabs are engaged cor-rectly and that the tailgate uppertrim has been put back in place
correctly.

Remove the bulb holder pressingon the tabs A,
Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts. When refitting, take care to position
the bulb holder and the light correctly.
Number plate lights (W 5 W) Insert a thin screwdriver into one of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Change the faulty bulb.
Rear lights
1 - Brake lights (P 21 W).
2 - Side lights (R 5 W).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W), right
side.
Fog lamp (P 21 W), left side.
These 5 bulbs are changed by remo- ving the light: Remove the corresponding boot side trim to access the light,
Remove the light fixing nut insidethe boot,
Remove the light fixing nut outsidethe boot,
Remove the light,
Unclip the harness,