2002 OLDSMOBILE AURORA display

1-5
3. Press and hold the memory button (1 or 2)
corresponding with your DRIVER # displayed on
the DIC for longer than three seconds. You will
hear two beeps confirming that the seat and mirror
positions have been entered into memory.
To set the seat and mirror positions for a second driver,
follow the previous steps, but start by pressing the
button with the unlock symbol on the transmitter that
displays the other DRIVER # on the DIC. Be sure to
use the memory button (1 or 2) which corresponds to
the DRIVER # identified by the second transmitter.
To recall your memory positions, your vehicle must
be in PARK (P). Push and release the memory button
(1 or 2) corresponding to the desired driving position.
The seat and mirrors will move to the position previously
stored for the identified driver. You will hear one beep.
To store the exit position for an easy exit, use the
following procedure:
1. First identify the DRIVER # on the DIC by pressing
the memory button (1 or 2) or by pressing the button
with the unlock symbol on the transmitter.
2. Adjust the driver's seat to the desired exit position.
3. Press and hold the EXIT button for longer than three
seconds. You will hear two beeps confirming that the
seat exit position has been entered into memory.To set the exit position for a second driver, follow the
previous steps, but start by pressing the button with the
unlock symbol on the transmitter that displays the other
DRIVER # on the DIC. Be sure to use the memory
button (1 or 2) which corresponds to the DRIVER #
identified by the other transmitter.
To recall the exit position, your vehicle must be in
PARK (P). Push and release the EXIT button and
the seat will move to the exit position previously stored
for the current identified driver. You will hear one beep.
If an exit position has not been stored for the current
identified driver, the seat will move all the way back.
To stop recall movement of the seat at any time, press
the driver's power seat control located on the outboard
side of the front seat.
Mirror and lumbar positions will not be stored or
recalled for the exit position.
If you would like your stored driving or exit position
to be recalled when unlocking your vehicle with the
transmitter, see ªDIC Personalization Programmingº
in the Index.
ProCarManuals.com

2-7 Central Door Unlocking System
If the key is held in the outside key cylinder unlock
position for more than two seconds, all doors will
unlock. All doors will also unlock if the key is turned to
the unlock position twice within three seconds.
Power Door Locks
With power door locks,
you can lock or unlock all
the doors on your vehicle
using the driver's or the
front passenger's door
lock switch.
Door Ajar Reminder
If a door is not fully closed when the transaxle is in
gear, a chime will sound and the DIC will display one
of these messages:

DRIVERS DOOR AJAR

PASSENGER DOOR AJAR

LEFT REAR DOOR AJAR

RIGHT REAR DOOR AJAR
Programmable Automatic Door Locks
This is a personalization feature that programs your door
locks to automatically lock or unlock your vehicle.
This feature also allows you to program the vehicle to
lock all doors when shifting out of PARK (P). Also, you
can program the door locks to do one of the following:

Unlock just the driver's door when shifting back
into PARK (P),

unlock all doors when shifting back into PARK (P),

unlock just the driver's door when turning the
ignition to OFF,

unlock all doors when turning the ignition to OFF, or

no automatic door unlock when shifting into
PARK (P) or turning the ignition to OFF.
ProCarManuals.com

2-23
ACC (Accessory): This position lets you use your
electrical accessories such as power windows, power
sunroof (option), radio and the windshield wipers.
ON: This is the position the switch returns to after
you start your engine and release the switch. This is the
position for normal driving. Even when the engine is not
running, you can use ON to operate your electrical
accessories and to display some instrument panel
warning lights.
START: This position starts your engine. When the
engine starts, release the key. The ignition switch will
return to ON for normal driving.Key Reminder Warning
If you leave your key in the OFF ignition position,
you will hear a warning chime when you open the
driver's door.
Always leave your key in OFF. If you leave it in any
other position, you will drain the battery power.
Retained Accessory Power (RAP)
After you turn the ignition off and remove the key, you
will still have power to accessories such as the power
windows, audio steering wheel controls, clock, sunroof
(option), accessory power outlet and the radio for up to
10 minutes. The instrument panel cluster lights will stay
on for a few seconds, then go out. Once you open a
door, the power will shut off.
ProCarManuals.com

2-36
As you signal a turn or a lane change, if the arrows flash
very fast, a bulb may be burned out and other drivers
won't see your turn signal.
If a bulb is burned out, replace it to help avoid
an accident.
If the arrows don't go on at all when you signal a turn,
check the fuse (see ªFuses and Circuit Breakersº in
the Index) and check for burned
-out bulbs.
Turn Signal On Chime
If your turn signal is left on for more than 0.8 miles
(1.3 km), a chime will sound at each flash of the turn
signal and the DIC will display the TURN SIGNAL
ON? reminder message. To turn off the chime and
message, move the turn signal lever to the off position.
To turn off the DIC message while the turn signal is
still active, press any button on the DIC. See
ªDriver Information Center (DIC)º in the
Index for more information.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high, push
the lever away from you until you hear a click. Then
release it.
When the high beams
are on, this light on the
instrument panel cluster
will also be on.
If the fog lamps are on when you turn on the
high
-beam headlamps, the fog lamps will turn off.
The fog lamps will turn back on when you turn
off the high
-beam headlamps.
ProCarManuals.com

2-45
With your headlamp control in AUTO when it is
dark enough outside, your low
-beam headlamps will
automatically come on. The other lamps that turn on
with your headlamps will also turn on. When it is bright
enough outside, the regular lamps will go off, and your
high
-beam headlamps change to the reduced brightness
of DRL.
To turn off all exterior lighting at night when you
are parked, turn the exterior lamps control all the way
toward OFF. The DRL will turn on automatically and
the HEADLAMPS SUGGESTED message will be
displayed on the DIC when you move the transaxle
out of PARK (P).
If the exterior lamps control is in the parking lamps
position at night, only the parking lamps will be on.
If the transaxle is out of PARK (P), only the
parking lamps will be active and the HEADLAMPS
SUGGESTED message will be displayed on the DIC.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Automatic Headlamps
The automatic headlamps will keep your headlamps on
when it is dark outside and the ignition is in ON.
It's possible that your headlamps may go out if you
drive from a dark area into a bright area like a lighted
parking lot. If this happens, turn on your headlamps
with the exterior lamps control.
Light Sensor
Your automatic headlamps and DRL work with the light
sensor on top of the instrument panel. Don't cover it up.
If you do it will read ªdarkº and the automatic headlamp
lighting will turn on.
ProCarManuals.com

2-47
Interior Lamps
Instrument Panel Brightness Knob
This feature controls the brightness of the instrument
panel lights.
The knob for this feature is
located on the driver's side
of the instrument panel.
Turn the knob clockwise to brighten the instrument
panel cluster lights and displays. Turn the knob
counterclockwise to dim the instrument panel cluster
lights and displays.
If it is day and your parking lamps are on, the instrument
panel cluster lights and displays will come on at full
intensity and will not be adjustable. If it is dark enough
outside and your parking lamps are on, the instrument
panel cluster lights and displays and the backlighting for
the door switches will come on, and can also be adjusted.
Courtesy Lamps
If it is dark enough outside and the front reading lamp
slider lever, located on the overhead console, is in the
AUTO position, when any door is opened all of the
vehicles courtesy lamps will come on. See ªReading
Lampsº in the Index. They make it easier for you to
enter and leave the vehicle. The courtesy lamps will
remain on for about 25 seconds after all doors have
been closed. They will then theater dim to off.
Move the front reading lamp slider lever to ON to turn
on the interior courtesy lamps. When the control is
moved back to either OFF or AUTO, the courtesy
lamps will immediately turn off.
If the control is OFF when the doors are opened, only
the lower instrument panel courtesy lamps will come on.
Also, if the control is OFF when illuminated entry or
delayed exit lighting are active, only the lower
instrument panel courtesy lamps will be on.
If a door is left ajar, your interior lamps will turn
off after 10 minutes to save your battery.
ProCarManuals.com

2-49 Parade Dimming
To activate the instrument panel backlighting during the
day, turn the exterior lamps control to the parking lamp
position. Dimming of the instrument panel display is not
possible during daylight hours. The instrument panel
display can only be adjusted when the parking lamps are
on and it is dark outside.
Perimeter Lighting
When the unlock symbol on the remote keyless entry
transmitter is pressed, the DRL headlamps, parking
lamps and back
-up lamps will turn on for approximately
25 seconds if it is dark enough outside.
This feature can be programmed to be on or off for each
transmitter. You can also program how long the exterior
lamps will stay on after unlocking the vehicle.
You must program this feature through the DIC. See
ªDIC Personalization Programmingº in the Index.
Front Reading Lamps
These lamps and the interior courtesy lamps will come
on when you open a door. They will turn off when you
turn on the ignition. If a door is left open, they will turn
off after about 10 minutes.
To turn on the reading lamps when the doors are closed,
press the button under the lamp you want on. Press it
again to turn the lamp off.
These lamps work even when the ignition is off. To avoid
draining your vehicle's battery, be sure to turn off all
front and rear reading lamps when leaving your vehicle.
ProCarManuals.com

2-50 Rear Reading Lamps
These lamps will come on when you open the doors.
You can also turn them on by pressing the button on the
side of the lamp. Press it again to turn them off.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle's battery
against drainage from the interior lamps, trunk lamp,
glove box lamp or cigarette lighters. When the ignition
is turned off, the power to these features will
automatically turn off after 10 minutes. Power will be
restored for an additional 10 minutes if any door is
opened, the trunk is opened or the courtesy lamp control
is turned on. To restore power to the cigarette lighters,
the ignition must be turned back to ON.
Battery Load Management
The battery load management feature is designed to
monitor the vehicle's electrical load and determine when
the battery is in a heavy discharge condition. During
times of high electrical loading, the engine may idle at a
higher rpm setting than normal to make sure the battery
charges. High electrical loads may occur when several
of the following are on: headlamps, high beams, fog
lamps, rear window defogger, blower fan, heated seats
and engine cooling fans.
If your vehicle's battery remains in a heavy discharge
condition for a long period of time, the fan, rear
defogger, heated seats and heated mirrors will be
disabled and the DIC will display BATTERY SAVER
ACTIVE. This can happen either under long periods of
idling or low speed driving with high electrical loading,
or in the event of a charging system fault.
ProCarManuals.com