2002 OLDSMOBILE AURORA change time

2-89
The DIC is used to program the personal choices of
two drivers. The drivers are recognized as DRIVER 1
and DRIVER 2. You will let the DIC and the vehicle
know which driver you are by using your remote keyless
entry transmitter or by pressing the appropriate memory
seat button located on the driver's door or choosing
the driver with the DIC. Each remote keyless entry
transmitter was pre
-programmed to belong to
DRIVER 1 or DRIVER 2. The personalization
features may be programmed differently for each driver.
When you press the unlock symbol on the transmitter,
the DIC will automatically change driver numbers
and the vehicle will recall the personal choice settings
that were last made to correspond to your transmitter,
including your radio and comfort control settings.
See ªComfort Controls, Personalizationº in the Index.
If you unlock the vehicle using the door key instead
of the transmitter, the personal choice settings will
correspond to the previous driver of the vehicle as
identified by the transmitter, the memory seat control
or the DIC. If this happens and you were not the last
driver of the vehicle, press the correct driver number
on the door panel for the memory seats, press the
unlock symbol on the transmitter or select the
personalization programming mode and choose
the correct driver number.After you have the correct driver number on the display
use the SELECT down arrow button to scroll through
the following messages and feature options:

DOORS LOCK IN GEAR
-- YES/NO

DOORS UNLOCK
-- YES/NO

ALL DOORS IN PARK
-- YES/NO

ALL DOORS AT KEY OFF
-- YES/NO

DRIVERS DOOR IN PARK
-- YES/NO

DRIVERS DOOR KEY OFF
-- YES/NO

PASS WINDOW LOCKOUT
-- YES/NO

KEY FOB FLASH LIGHTS
-- YES/NO

KEY FOB CHIRP HORN
-- YES/NO

DELAY LOCK OF DOORS
-- YES/NO

PERIMETER LIGHTS
-- YES/NO

EXT LIGHT TIMEOUT
-- 5 to 30 Seconds

DISPLAY DRIVER ID
-- YES/NO

KEY FOB MEMORY SEAT
-- YES/NO

DRIVING POSITION
-- YES

EXIT POSITION
-- YES

TILT MIRROR REVERSE
-- YES/NO
ProCarManuals.com

2-92
Window Lockout Personalization
The number of passenger windows locked out by
the window LOCK switch can be programmed through
the DIC.
Press the SELECT right arrow button to toggle between
your choices and change the settings. Press the SELECT
down arrow button to store your changes in memory and
move on to the next selection.
If you select YES for PASS WINDOW LOCKOUT,
all three passenger window switches will be locked out
when the window LOCK switch is on.
If you select NO for PASS WINDOW LOCKOUT, only
the two rear passenger window switches will be locked
out when the window LOCK switch is on.
For more information on this feature, see ªWindow
Lockº in the Index.
Security Feedback
You can program the security feedback feature to
change to the following modes:
Mode 1: No feedback when locking or unlocking
the vehicle.
Mode 2: Parking lamps and the DRL will flash twice
when unlocking the vehicle and flash once when locking
the vehicle.Mode 3: Horn chirps when all doors are unlocked
(second unlock button press) and when locking
the vehicle.
Mode 4: Parking lamps and the DRL will flash twice
each time the button with the unlock symbol is pressed;
the horn chirps when all doors are unlocked. Parking
lamps and the exterior lamps flash once and the horn
chirps when locking the vehicle.
You can change these modes by different selections
of the following DIC displays:

KEY FOB LIGHTS FLASH
-- YES/NO

KEY FOB HORN CHIRP
-- YES/NO
Press the SELECT right arrow button to toggle between
your choices and change the settings. Press the SELECT
down arrow button to store your changes in memory and
move on to the next selection.
If you would like to program your vehicle to Mode 1,
do the following:
1. Select NO for KEY FOB LIGHTS FLASH.
2. Select NO for KEY FOB HORN CHIRP.
ProCarManuals.com

2-94
The EXT LIGHTS TIMEOUT feature can be changed
to the desired setting by using the SELECT right arrow
button to toggle from 5 to 30 seconds. Each toggle will
increase the time by five seconds. Once the desired
timeout is displayed, press SELECT down arrow to
record your choice and move on to the next personal
choice feature.
For more information on this feature, see ªPerimeter
Lightingº in the Index.
Driver ID
This feature displays the driver ID, as identified by the
DIC. If you choose YES when DISPLAY DRIVER ID
is shown on the DIC, the driver number will be
displayed every time the ignition is turned on. If you
choose NO when DISPLAY DRIVER ID is shown on
the DIC, the driver number can be displayed by pressing
either a button on the remote keyless entry transmitter or
a memory seat button.
Memory Seat Recall (If Equipped)
This feature recalls the position of the driver's seat.
When this feature is active, the memory seat and
mirror positions will be recalled for the identified driver
when the remote keyless entry transmitter is used to
enter the vehicle.You can program this feature to be active by choosing YES
when the KEY FOB MEMORY SEAT choice appears, or
inactive by choosing NO when the KEY FOB MEMORY
SEAT choice appears on the DIC. Make your choices by
pressing the SELECT right arrow button and store them in
memory by pressing the SELECT down arrow button.
You can also program this feature to recall your memory
seat position or the exit seat position. Select YES for
KEY FOB MEMORY SEAT then use the SELECT
right arrow button to toggle between DRIVING
POSITION
- YES and EXIT POSITION - YES.
When the desired position is displayed on the DIC, press
the SELECT down arrow button to save that position in
memory and move on to the next selection.
For more information on this feature, see ªMemory Seat
and Mirrorsº in the Index.
Parallel Park Assist (If Equipped)
The parallel park assist mirror, which tips the passenger
mirror while the vehicle is in REVERSE (R), can be
made active or inactive through the DIC. When TILT
MIRROR REVERSE appears on the display, use the
SELECT right arrow button to toggle the arrow between
YES and NO. When you have made your choice, press
the SELECT down arrow button to record your
selection. For more information on this feature, see
ªMirrorsº in the Index.
ProCarManuals.com

2-95 DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:
EXP (Export ID) Warning Message. . . . . . . . . . . .
1 AIR BAG PROBLEM. . . . . . . . . . . . . . . . . . . . . .
3 CHANGE OIL SOON. . . . . . . . . . . . . . . . . . . . . .
4 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . . . .
5 CHECK OIL LEVEL. . . . . . . . . . . . . . . . . . . . . . .
6 TRANS HOT...IDLE ENG. . . . . . . . . . . . . . . . . . .
7 CONFIRM TIME & DATE. . . . . . . . . . . . . . . . . .
8 DRIVERS DOOR AJAR. . . . . . . . . . . . . . . . . . . .
9 ENGINE HOT...A/C OFF. . . . . . . . . . . . . . . . . . .
10 HOT...REDUCE ENG RPM. . . . . . . . . . . . . . . . .
11 HOT...STOP ENGINE *. . . . . . . . . . . . . . . . . . . .
12 THEFT SYSTEM FAULT. . . . . . . . . . . . . . . . . .
13 LEFT REAR DOOR AJAR. . . . . . . . . . . . . . . . .
14 LOW BRAKE FLUID *. . . . . . . . . . . . . . . . . . . .
15 LOW ENGINE COOLANT. . . . . . . . . . . . . . . . .
16 LOW FUEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 LOW OIL PRESSURE *. . . . . . . . . . . . . . . . . . . 18 LOW TIRE PRESSURE. . . . . . . . . . . . . . . . . . .
19 LOW WASHER FLUID. . . . . . . . . . . . . . . . . . . .
20 PARK BRAKE SET *. . . . . . . . . . . . . . . . . . . . .
21 PASSENGER DOOR AJAR. . . . . . . . . . . . . . . .
22 RIGHT REAR DOOR AJAR. . . . . . . . . . . . . . . .
23 SERVICE VEHICLE SOON. . . . . . . . . . . . . . . .
24 TURN SIGNAL ON?. . . . . . . . . . . . . . . . . . . . . .
25 THEFT ATTEMPTED. . . . . . . . . . . . . . . . . . . . .
26 SERV STABILITY SYS. . . . . . . . . . . . . . . . . . . .
27 HEADLAMPS SUGGESTED. . . . . . . . . . . . . . .
28 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
29 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
32 HOT...IDLE ENGINE. . . . . . . . . . . . . . . . . . . . .
33 STARTING DISABLED *. . . . . . . . . . . . . . . . . .
36 CHECK GAS CAP. . . . . . . . . . . . . . . . . . . . . . . .
42 STABILITY ACTIVE. . . . . . . . . . . . . . . . . . . . .
The EXP codes are used to make translation from
English to other languages easier.
Pressing the RESET button will remove the above
messages or warnings from the DIC display, unless
noted by an asterisk (*).
ProCarManuals.com

3-6 Comfort Controls Personalization
(If Equipped)
This feature enables up to two drivers to store and recall
comfort control settings for temperature, air delivery
mode and fan speed.
The memory buttons (1 or 2) for this feature are located
on the driver's door panel and correspond to the
numbers (1 or 2) found on the back of each remote
keyless entry transmitter.
To recall comfort settings, press the unlock button
on the remote keyless entry transmitter and put the
ignition in ACC (Accessory) or ON. The climate
control setting last chosen by the identified
driver (1 or 2) will be recalled.
To program a personal climate control setting, do
the following:
1. Choose a climate control setting for the driver
and if desired, for the passenger. See ªAutomatic
Electronic Climate Controlº and ªPassenger
Temperature Control (Option)º earlier in this section.
2. Adjust the direction of the airflow.3. Locate the memory buttons on the driver's
door panel.
4. Press a memory button (1 or 2) until you hear two
beeps. The beeps confirm that your selection has
been saved and can now be recalled.
Follow these steps each time you want to change the
stored settings. For more information on the memory
feature, see ªMemory Seat and Mirrorsº in the Index.
Air Conditioning
The air conditioner cools and dehumidifies the air inside
of the vehicle.
The air conditioning compressor is enabled in all
modes unless the air conditioning button is not selected
(the indicator light will not be illuminated). However,
the air conditioning compressor will not operate when
the outside temperature is below 34
F (1
C). When the
air conditioner is on, you may sometimes notice slight
changes in your vehicle's engine speed and power. This
is normal, because the system is designed to cycle the
compressor on and off to maintain the desired
temperature and to help with fuel economy.
ProCarManuals.com

3-17
SEEK : Press the right or left arrow to search for
the next or previous selection on the tape. Your tape
must have at least three seconds of silence between each
selection for seek to work. You can skip nine selections
forward or backward on the tape. Choose how many
selections you want to skip. Press the right or left SEEK
arrows that many times. The number of selections to be
skipped will appear on the display.
SCAN : Press and hold either arrow for more than
two seconds until you hear a beep and SCAN appears on
the display. The tape will go to the next selection, play
for a few seconds, then go on to the next selection. Press
this button again to stop scanning.
BAND: Press this button to listen to the radio when a
cassette tape is playing. The tape will stop but remain in
the player.
TP CD (TAPE): Press this button to play to play a
cassette tape or a CD when listening to the radio. Press
TP CD to switch between the tape and compact disc if
both are loaded. The inactive tape or CD will remain
safely inside the radio for future listening. The display
will show the TAPE and CD symbols.If you have the optional CD changer and it is loaded,
the TP CD button will activate the changer and a symbol
will be lit on the display.
(Eject): Press this button, located next to the
cassette tape slot, to eject a tape. Eject may be activated
with either the ignition or radio off. Cassettes may be
loaded with the radio and ignition off if this button is
pressed first.
Cassette Tape Messages
If an error occurs while trying to play a cassette tape,
it could be for one of the following reasons:
TIGHT TAPE: When this message is displayed, the
tape is tight and the player can't turn the tape hubs.
Remove the tape. Hold the tape with the open end down
and try to turn the right hub counterclockwise with a
pencil. Turn the tape over and repeat. If the hubs do not
turn easily, your tape may be damaged and should not be
used in the player. Try a new tape to make sure your
player is working properly.
BROKEN TAPE: If this message is displayed, the tape
is broken. Try a new tape.
ProCarManuals.com

3-19
SEEK : Press the left arrow to go to the start of the
current track if more than eight seconds have played.
Press the right arrow to go to the next track. If you hold
this button or press it more than once, the player will
continue moving backward or forward through the disc.
SCAN : Press and hold either arrow for more than
two seconds until you hear a beep and SCAN appears on
the display. The disc will go to the next track, play for a
few seconds, then go on to the next track. Press this
button again to stop scanning. The sound will mute
while scanning. SCAN and the track number will appear
on the display.
RCL (Recall): Press this knob to see how long the
current track has been playing. To change what is
normally shown on the display (track or elapsed time),
press the knob until you see the display you want, then
hold the knob until the display flashes. While elapsed
time is showing, EL TM will appear on the display.BAND: Press this button to listen to the radio when
a CD is playing.
TP CD (Tape): Press this button to play to play a
cassette tape or a CD when listening to the radio. Press
TP CD to switch between the tape and compact disc if
both are loaded. The inactive tape or CD will remain
safely inside the radio for future listening. The display
will show the TAPE and CD symbols.
If you have the optional CD changer and the CD
changer is loaded, the TP CD button will activate the
changer and a symbol will be lit in the display.
(Eject): Press this button to eject a CD. Eject
may be activated with either the ignition or radio off.
CDs may be loaded with the radio and ignition off if
this button is pressed first.
ProCarManuals.com

3-23
All of the CD functions are controlled by the radio
pushbuttons except for ejecting the magazine. Whenever
a CD magazine with discs is loaded in the changer, the
compact disc symbol will appear on the radio display. If
the CD changer is checking the magazine for CDs, the
compact disc symbol will flash on the display until the
changer is ready to play. If CD changer mode is entered
during initialization, LOADING will appear on the
display. When a CD begins playing, a disc and track
number will be displayed. The disc numbers are listed
on the front of the magazine.
Playing a Compact Disc
If an error appears on the display, see ªCompact Disc
Messagesº later in this section.
1 REV (Reverse): Press and hold this pushbutton to
quickly reverse within a track. As the CD reverses,
elapsed time will be displayed with a flashing arrow to
help you find the correct passage.
2 FWD (Forward): Press and hold this pushbutton to
quickly advance within a track. As the CD advances,
elapsed time will be displayed with a flashing arrow to
help you find the correct passage.4 RDM (Random): Press this pushbutton to play the
tracks on the discs in random, rather than sequential
order. If you press SEEK while in the random mode,
discs and tracks will be scanned randomly. Press this
button again to turn off the random feature and return to
normal operation.
5 SIDE: Press this pushbutton to select the next disc in
the magazine. Each time you press SIDE, the disc
number will be displayed.
RCL (Recall): Press this knob to see what track is
currently playing. Press RCL again within five seconds
to see how long the track has been playing. EL TM will
appear on the display when in elapsed time mode. When
a new track starts to play, the track number will also
appear. Press RCL a third time and the time of day will
be displayed.
SEEK : Press the right or left arrow to go to the
next or previous tracks on the disc.
ProCarManuals.com