2002 MAZDA MODEL MX-5 MIATA lock

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q42-EA-01F

Schedule 2
I
: Inspect: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R: Replace
L :Lubricate
*: According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance
services be performed at the recommended time or kilometrage (mileage) period to ensure long-term
reliability.
Maintenance Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first
Months 4 8 12 16 20 24 28 32 36 40 44 48
× 1000 Km 8 1624324048566472808896
(× 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Engine valve clearance I
Engine timing belt Replace every 96,000km (60,000miles)
Drive belts (tension) II
Engine oil Puerto Rico Replace every 5,000km (3,000miles) or 3 months
others RRRRRRRRRRRR
Engine oil filter RRRRRRRRRRRR
Cooling system II
Engine coolant Replace at first 72,000km (45,000miles) or 36 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant level IIIIIIIIIIII
Idle speed II
Air filter I
*R
I *R
Fuel lines and hoses*II
Hoses and tubes for emission*I
Spark plugs RR
Function of all lights IIIIIIIIIIII
Brake lines, hoses and connections II
Brake and clutch fluid level IIIIIIIIIIII
Disc brakes IIII
Tire inflation pressure and tire wear IIIIIIIIIIII
Steering operation and linkages II
Power steering fluid level IIIIIIIIIIII
Manual transmission oil RR
Rear differential oil RR
Front suspension ball joints II
Driveshaft dust boots II
Bolts and nuts on chassis and body IIII
Exhaust system heat shields II
All locks and hinges LLLLLLLLLLLL
Washer fluid level IIIIIIIIIIII
J07L(02MY).book Page 5 Monday, June 11, 2001 4:52 PM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F
Engine Compartment Overview
Fuse blockEngine oil-filler cap Cooling system cap Power steering fluid filler cap/dipstick Air filterClutch fluid reservoir
(Only for manual
transmission model)
Automatic transmission fluid-level dipstick
(Only for automatic transmission model)
Engine oil dipstickBrake fluid reservoir
Washer fluid reservoir
(TypeA)
The battery is in the trunk
ngine coolant
eservoir Washer fluid reservoir (TypeB)
J07L(02MY).book Page 12 Monday, June 11, 2001 4:52 PM

8-16
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F
If it’s at or near LOW, add enough coolant
to the coolant reservoir to provide
freezing and corrosion protection and to
bring the level to FULL.
Do not overfill.
If new coolant is required frequently,
consult an Authorized Mazda Dealer.

Changing Coolant
Change coolant according to Scheduled
Maintenance (page 8-3). For mixture percentage:
To change coolant
Radiator coolant will damage paint.
Rinse it off quickly.
•
Use only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant
’s effectiveness.
• Don
’t add only water. Always add a
proper coolant mixture.
• The engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
• DO NOT USE alcohol or methanol
antifreeze. DO NOT MIX alcohol
or methanol with the coolant. This
could damage the cooling system.
• Don
’t use a solution that contains
more than 60 % antifreeze.
This would reduce effectiveness.
CAUTION
CAUTION
Protection Volume
Antifreeze solution Wa t e r
Above −
16° C (3° F) 35% 65%
Above −
26° C (−
15° F) 45 55
Above −
40° C (−
40° F) 55 45
Removing the Cooling System Cap:
Removing the cooling system cap or
drain plug while the engine is
running or hot is dangerous. This
might lead to cooling system and
engine damage and could result in
serious injury from escaping hot
coolant or steam. Turn off the engine
and wait until it ’s cool. Even then, be
very careful when removing the cap
or drain plug. Wrap a thick cloth
around it and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you ’re sure all the pressure is
gone, press down on the cap — still
using a cloth — turn the cap, and
remove it.
WARNING
J07L(02MY).book Page 16 Monday, June 11, 2001 4:52 PM

8-23
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the engine hood’s secondary
latch keeps the hood from opening when
the primary latch is released. A viscous paper air filter fits inside the air
cleaner housing, as shown. It
’s been
specially treated and should not be
cleaned and reused. Replace it when
necessary.

Replacing the Air Filter
1. Unfasten the clamps.
Body LubricationAir Filter
Don
’t drive without an air filter. This
could result in excessive engine wear.
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than recommended intervals.
CAUTION
Clamp
J07L(02MY).book Page 23 Monday, June 11, 2001 4:52 PM

8-25
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F

Replacing Windshield Wiper
Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm. 2. Hold the end of the rubber and pull
until the tabs are free of the metal
support.
3. Remove the metal stiffeners from the blade rubber and install them in new
blades.
To prevent damage to the wiper arms
and other components, don
’t move the
wipers by hand.
To prevent damage to the windshield,
don ’t let the wiper arm fall on it.
CAUTION
Push
Plastic locking clip
CAUTION
Pull out
Ta b Metal support
Stiffeners
J07L(02MY).book Page 25 Monday, June 11, 2001 4:52 PM

8-32
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F
Your Mazda’s headlights have replaceable
halogen bulbs.
Replacing a Headlight Bulb
1. Make sure the headlight switch is off.
2. Lift the hood and find the bulb in the
rear of the headlight body.
3. Turn the socket and bulb assembly counterclockwise and remove it while
holding the rubber socket cover in
place. Carefully remove the headlight
bulb from its socket in the reflector by
gently pulling it straight backward out
of the socket.
4. Remove the bulb from the electrical connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
5. Install the new bulb in the reverse order of removal.
Handling Halogen Bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
WARNING
Do not touch the glass surface
Ta b
Low beam bulb
High beam bulb
Ta b
J07L(02MY).book Page 32 Monday, June 11, 2001 4:52 PM

8-38
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F
If the headlights or other electrical
components don’t work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
6. Turn off the ignition switch and all other switches.
7. Remove the fuse block cover.
8. If a fuse is blown, replace it with a new one of the same rating. When replacing the 100A fuse:
1. Turn off the ignition switch.
2. Remove the negative battery terminal.
3. Remove the A nuts.
4. Lift the fuse block and remove the B
bolts.
5. Replace the fuse with a new one of the
same rating.
6. Install in the reverse order of removal.
Fuse block cover
Ta b
NormalBlown
100A fuse
A B
A
B
J07L(02MY).book Page 38 Monday, June 11, 2001 4:52 PM

8-39
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F

Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE RATING
PROTECTED COMPONENT
1 HEAD 40A Headlights, Rear defroster, Auto antenna
2 FUEL INJ 30A Fuel injection
3 MAIN 100A For protection of all circuits
4 IG KEY 60A All ignition related circuits
5 BLOWER 30A Blower motor
6 FAN 30A Cooling fan, Additional fan (air conditioner)
7 BTN 1 30A Taillights, Dashboard illumination
8 BTN 2 20A Audio amp, Turn signal lights
9 ABS 20A Antilock brake system
10 STOP 15A Brake lights, Horn, Shift lock
J07L(02MY).book Page 39 Monday, June 11, 2001 4:52 PM