2002 MAZDA MODEL 626 brake

8-16
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Adding Brake/Clutch Fluid
If the fluid level is low, add fluid until it
reaches MAX.
Before adding fluid, thoroughly clean the
area around the cap.
Spilled Brake Fluid:Spilled brake fluid is dangerous. If it
gets in your eyes, they could be
seriously injured. If this happens,
immediately flush your eyes with
water and get medical attention.
Brake fluid spilled on a hot engine
could cause a fire. Be careful not to
spill brake fluid on yourself or on the
engine.
Low Brake/Clutch Fluid Levels:
Low brake/clutch fluid levels are
dangerous. Low levels could signal
brake lining wear or a brake system
leak. Your brakes could fail and cause
an accident. If you find a low fluid
level, have the brakes and clutch
inspected.
WARNING• Brake and clutch fluid will damage
painted surfaces. If brake or clutch
fluid does get on a painted surface,
wipe it off immediately.
• Using nonspecified brake and clutch
fluids (page 10-4) will damage the
systems. Mixing different fluids
will also damage them.
If the brake/clutch system
frequently requires new fluid,
consult an Authorized Mazda
Dealer.
CAUTION
J94S.book Page 16 Saturday, June 23, 2001 1:04 PM

8-17
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Inspecting Power Steering Fluid
Level
Inspect the fluid level at each engine oil
change. Add fluid if necessary; it does not
require periodic changing.
The level must be kept between the HIGH
and LOW marks.
Visually examine the lines and hoses for
leaks and damage.
1. Park on a level surface, well off the
right-of-way, and set the parking brake
firmly.
2. Turn off the engine and allow it to cool. 3. Remove the filler cap and attached
dipstick.
4. Wipe them clean and put them back.
5. Remove again and inspect the level.
6. It must be between HIGH and LOW. Add fluid if necessary.
Don ’t overfill.
If new fluid is required frequently, consult
an Authorized Mazda Dealer.
Power Steering Fluid
To avoid damage to the power steering
pump, don’ t operate the vehicle for
long periods when the power steering
fluid level is low.
NOTE
Use specified power steering fluid
(page 10-4).
CAUTION
High
Low OK
J94S.book Page 17 Saturday, June 23, 2001 1:04 PM

8-18
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Inspecting Automatic transaxle
Fluid Level
The automatic transaxle fluid level should
be inspected regularly. Measure it as
described below.
The volume of fluid changes with the
temperature. Fluid must be checked at idle
without driving at normal operating
temperature.
1. Park on a level surface and set the
parking brake firmly.
2. Idle the engine about two minutes. Push down on the brake pedal.
3. Move the shift lever through all ranges and set it at P. 4. With the engine still idling, pull out the
dipstick, wipe it clean, and put it back.
5. Pull it out again. The proper fluid level is marked on the
dipstick as follows.
2.0-liter engine
Scale A
When the engine has been running and the
fluid is at normal operating temperature,
about 65 °C (150 °F) to 77 °C (170 °F), the
level must be within the crosshatched area
on the dipstick.
Automatic Transaxle Fluid
(ATF)
• Low fluid level causes transaxle
slippage. Overfilling can cause
foaming, loss of fluid, and transaxle
malfunction.
• Use specified fluid (page 10-4). A
nonspecified fluid could result in
transaxle malfunction and failure.
CAUTION
Sudden Vehicle Movement:Shifting the shift lever without first
depressing the brake pedal is
dangerous. The vehicle could move
suddenly and cause an accident.
Make sure the brake pedal is applied
before shifting the shift lever.
WARNING
A
B
J94S.book Page 18 Saturday, June 23, 2001 1:04 PM

8-29
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Light Bulbs
Headlights
Interior light
Courtesy lights
Front-turn signal lights/Parking lights
License plate lights
High-mount brake lightTrunk light
Rear-turn signal lights
Reverse lights
Brake lights/Taillights
J94S.book Page 29 Saturday, June 23, 2001 1:04 PM

8-33
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Replacing a Bulb (Rear)
Rear bulb access
To replace the turn-signal light, brake
light/taillight or reverse light bulb, pull the
center section of the plastic retainer and
remove the retainers and trunk end trim.
J94S.book Page 33 Saturday, June 23, 2001 1:04 PM

8-34
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
License plate lights
Rear-turn signal lights
Brake lights/Taillights
Reverse lights
Trunk light
High-mount brake light
J94S.book Page 34 Saturday, June 23, 2001 1:04 PM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
1EGI INJ 30A Fuel injection
system
2 DEFOG 40A Rear window
defroster
3 —— —
4 MAIN 100A For protection of
all circuits
5 IG KEY 30A RADIO,
SUNROOF,
TURN, METER, ENGINE,
POWER
WINDOW,
WIPER fuses,
Ignition system
6 HEATER 40A Heater, Air
conditionerDESCRIPTION FUSE
RATING PROTECTED
COMPONENT
7 BTN 40A TAIL, STOP,
ROOM, DOOR LOCK,
HAZARD,
POWER SEAT fuses
8 COOLING
FA N 30A Cooling fan
9 AD FAN 30A Additional fan
10 (ABS) 60A Antilock brake
system
11 TAIL 15A Taillights,
Parking lights, Dashboard
illumination,
License plate
lights, Switches illumination
12 HORN 15A Horn
J94S.book Page 37 Saturday, June 23, 2001 1:04 PM

8-38
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
DESCRIPTIONFUSE
RATING PROTECTED
COMPONENT
13 (ABS) 20A Antilock brake
system
14 —— —
15 —— —
16 H/L-L 15A Headlight (Left)
17 H/L-R 15A Headlight
(Right)
18 (ABS) 20A Antilock brake
system
J94S.book Page 38 Saturday, June 23, 2001 1:04 PM