2002 MAZDA MODEL 626 audio

6-16
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
•A new CD may have rough edges on its
inner and outer perimeters. If a disc
with rough edges is used, proper
setting will not be possible and the CD
player/changer will not play the CD.
Remove the rough edges in advance by
using a ball-point pen or pencil as
shown below. To remove the rough
edges, rub the side of the pen or pencil
against the inner and outer perimeter of
the CD.
• When driving over uneven surfaces, the
sound will jump.
• The CD player/changer has been
designed to play CDs bearing the
identification logo as shown. No other
discs can be played. •
Be sure never to touch the signal
surface when handling the CDs. Pick
up a CD by grasping the outer edge or
the edge of the hole and the outer edge.
• Do not stick paper or tape on the CD.
Avoid scratching the reverse side (the
side without a label).
• Dust, finger smudges, and dirt can
decrease the amount of light reflected
from the signal surface, thus affecting
sound quality. If the CD should
become soiled, gently wipe it with a
soft cloth from the center of the CD to
the edge.
• Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the CD and must not be used. Anything
that can damage, warp, or fog plastic
should never be used to clean CDs.
• CDs, like traditional audio records, are
made of plastic. To avoid warping,
keep the CDs in their cases and do not
store them where they will be exposed
to direct sunlight.
• The CD player/changer ejects the CD if
the CD is inserted upside down. Also
dirty and/or defective CDs may be
ejected.
• 8 cm (3 in) CDs and CD accessories
(e.g. 8 cm disc adapter) cannot be used
in the CD player/changer.
J94S.book Page 16 Saturday, June 23, 2001 1:04 PM

6-17
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
•Do not insert cleaning discs in the CD
player/changer.
• Do not insert any disc with a peel-off
or seal on it.
J94S.book Page 17 Saturday, June 23, 2001 1:04 PM

6-18
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
J94S.book Page 18 Saturday, June 23, 2001 1:04 PM

6-19
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
Power/Volume/Sound Controls ............................................................................................. 6-20
Clock ..................................................................................................................................... 6-22
Operating the Radio ........................................................................................................... ... 6-24
Operating the Cassette Tape Player ....................................................................................... 6-26
Operating the Mini Disc (MD) Player ................................................................................... 6-28
Operating the Compact Disc (CD) Player ............................................................................. 6-30
Operating the In-Dash CD Changer ...................................................................................... 6-32
Error Indications ............................................................................................................. ....... 6-35
Audio Set
CD PlayerIn-dash CD Changer
Cassette Tape Player Mini Disc (MD) PlayerIllustration is of a representative audio unit.
J94S.book Page 19 Saturday, June 23, 2001 1:04 PM

6-20
Interior Comfort
Audio System
Form No. 8Q50-EA-01G





Power/Volume/Sound Controls
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume knob to turn the
audio system on.
Press the power/volume knob again to
turn the audio system off. Volume adjustmentTo adjust the volume, turn the power/
volume knob.
Turn the power/volume knob to the right
to increase volume, to the left to decrease
it.
Display
Audio control knob
Power/Volume knob
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period when the
engine is not running.
J94S.book Page 20 Saturday, June 23, 2001 1:04 PM

6-21
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
Audio sound adjustment
1. Press the audio control knob to select bass, mid-range, treble, fade or balance
control. The selected function will be
indicated.
*Depending on the model, this function, may not be available.
2. Turn the audio control knob to adjust the selected functions as follows:
Indication Turn Left Turn Right
Decrease bass Increase bass
Decrease
mid-range Increase
mid-range
Decrease treble Increase
treble
Shift the sound
to the front Shift the
sound
to the rear
Shift the sound
to the left Shift the
sound
to the right
NOTE
About 5 seconds after selecting any
mode, the volume function will be
automatically selected. To reset bass,
mid-range, treble, fade, and balance,
press the audio control knob for 2
seconds. The unit will beep and "CL"
will be displayed.
J94S.book Page 21 Saturday, June 23, 2001 1:04 PM

6-22
Interior Comfort
Audio System
Form No. 8Q50-EA-01G





Clock
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock ’s current time will flash.
2. To advance the hours, press the hour set button ( ). To advance the
minutes, press the minute set button
( ) while the time is flashing.
3. Press the clock button ( ) again to start the clock. Exact hour adjustment 1. To set the exact hour, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock ’s current time will flash.
2. Press the clock button ( ) again and the time will be adjusted as
follows:
(Example)
12:01 —12:29→ 12:00
12:30 —12:59→ 1:00
Display Clock button
Hour set
button
Minute set
button
NOTE
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle ’s battery is disconnected), the
clock will need to be reset.
J94S.book Page 22 Saturday, June 23, 2001 1:04 PM

6-23
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
Changing the display mode
The display on the unit can be changed by
pressing the clock button ( ). This
alternates the display between time and
audio. When the clock mode has been
selected, the time will be displayed.
NOTE
If audio operation is selected while the
time mode is on, the selected audio
mode will be displayed for ten
seconds, then the display will revert to
the time mode.
J94S.book Page 23 Saturday, June 23, 2001 1:04 PM