2002 MAZDA 6 trunk

TRIM
S–23
S
TRUNK END TRIM REMOVAL/INSTALLATIONA6E774468890201WGN
1. Pull the trunk end trim upward, then disengage
clips A and pins B from the body.
2. Remove the trunk end trim.
3. Install in the reverse order of removal.
End Of Sie
LIFTGATE UPPER TRIM REMOVAL/INSTALLATIONA6E774468930201WGN
Without rear spoiler
Caution
•Removing the liftgate upper trim by pulling on the middle section of the trim could damage the
high-mount brake light. When removing the trim, be sure to pull on the side edges of the trim only.
1. Pull the liftgate upper trim on the side edges
towards you, then disengage pins A from the
body.
2. Pull the middle section of the trim towards you
and disengage clips B and pin C from the body.
3. Remove the liftgate upper trim.
4. Install in the reverse order of removal.
With rear spoiler
1. Pull the liftgate upper trim toward you, then
disengage the pin A, C and clip B from the body.
2. Remove the liftgate upper trim.
3. Install in the reverse order of removal.
End Of Sie
AB
A
A
B
A
A
A B
TRUNK END TRIM
PIN B
CLIP A
A6A7744W108
AC B
AB
CLIP B
PIN A LIFTGATE UPPER TRIM
PIN C
A6A7744W109
ABAB
C
CLIP BPIN C LIFTGATE UPPER TRIM
PIN A
A6A7744W110

TRIM
S–25
S
TONNEAU COVER ANCHOR REMOVAL/INSTALLATIONA6E7744683202011. Remove the trunk side upper trim.
2. Remove the screws.
3. Remove the tonneau cover anchor.
4. Install in the reverse order of removal.
End Of Sie
SCREWTONNEAU COVER ANCHOR
A6A7744W114

SEAT
S–29
S
REAR SEAT REMOVAL/INSTALLATIONA6E7752572002014WD (WGN)
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
.
Remote wire removal note
1. Turn over the trunk floor mat.
2. Remove the case.
3. Remove the remote wire.
End Of Sie
SEAT
3
2
1
1
A: 36.3—53.9 N·m
{3.71—5.49 kgf·m, 26.8—39.7 ft·lbf}
B: 38.3—78.4 N·m
{3.91—7.99 kgf·m, 28.3—57.8 ft·lbf}
A
A
B
B
A6E77521102
1 Remote wire
(See S–29 Remote wire removal note)2 Rear seat cushion
3 Rear seat back
CASE
REMOTE WIRE
A6E7752W014

T–26
WIPER AND WASHER
13. Remove rear washer hose No.3 from clip C.
14. Remove rear washer hose No.3 and joint pipe D.
15. Remove the headliner. (See S–26 HEADLINER
REMOVAL/INSTALLATION)
16. Remove the tape from rear washer hose No.4.
17. Install in the reverse order of removal.
End Of SieINTERMITTENT REAR WIPER RELAY REMOVAL/INSTALLATIONA6E8116668102011. Disconnect the negative battery cable.
2. Remove the trunk side trim. (See S–21 TRUNK SIDE TRIM REMOVAL/INSTALLATION)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
JOINT
PIPE D
REAR WASHER
HOSE NO.3CLIP C
a
A6E81161150
a
REAR WASHER
HOSE NO.4 TAPE
TAPE
A6E81161151
1Bolt
2 Intermittent rear wiper relay
3 Connector
1
23
A6J81161015