WHEEL ALIGNMENT
R–9
R
Total Toe-in Adjustment
1. Center the steering wheel and confirm that the vehicle wheels/tires are pointing straight.
2. Loosen the left and right tie-rod end locknuts and turn the tie-rods equally. Both tie rods are right threaded, so
turning the right tie-rod toward the front of the vehicle and the left toward the rear increases toe-in.
Note
•Turning both tie-rods one complete turn changes toe-in by about 6 mm {0.24 in} (0°36').
3. Tighten the tie-rod end locknuts to the specified torque.
Tightening torque
68.6—98.0 N·m {7.00—9.99 kgf·m, 50.6—72.2 ft·lbf}
4. Verify that the boot is not twisted, and install the boot clamp.
End Of Sie
REAR WHEEL ALIGNMENT (WGN)A6E741201016201Specification (Unloaded)*1
2WD
*
1: Engine coolant and engine oil are at specified level. Spare tire, jack and tools are in designated position.
*2: Difference between left and right must not exceed 1°30'.*3: Distance between wheel center and fender brim is 407 mm {16.02 in} (reference value).
4WD
*
1: Engine coolant and engine oil are at specified level. Spare tire, jack and tools are in designated position.
*2: Difference between left and right must not exceed 1°30'.
Note
•Adjust the toe-in after adjusting the camber.
Camber Adjustment
1. Loosen the cam nut on the lower arm.
2. Turn the adjusting cam bolt to provide the correct
camber angles as indicated.
3. Tighten the cam nut.
Tightening torque
86.2—116.6 N·m {8.80—11.88 kgf·m, 63.58—
85.99 ft·lbf}
ItemFuel gauge indication
Empty 1/4 1/2 3/4 Full
Total toe-in(mm {in}) Tire: 2±4 {0.08±0.16}, Rim inner: 1±3 {0.04±0.12}
(degree) 0°11′±0°22′
Camber angle
*2 normal–0°59′±1°–1°00′±1°–1°02′±1°–1°04′±1°–1°06′±1°
elevated
*3–0°52′±1°–0°53′±1°–0°55′±1°–0°56′±1°–0°58′±1°
Thrust angle 0°±0°48′
ItemFuel gauge indication
Empty 1/4 1/2 3/4 Full
Total toe-in(mm {in}) Tire: 2±4 {0.08±0.16}, Rim inner: 1±3 {0.04±0.12}
(degree) 0°11′±0°22′
Camber angle*
2 –0°55′±1°–0°57′±1°–0°59′±1°–1°01′±1°–1°03′±1°
Thrust angle (degree) 0°±0°48′
Left wheel Right wheel
Positive direction ClockwiseCounter-
clockwise
Negative directionCounter-
clockwiseClockwise
LEFT SIDE
(VIEW FROM
FRONT OF THE
VEHICLE)
ADJUSTING
CAM BOLT
A6E7412W003
TD–4
TECHNICAL DATA
ENGINE ELECTRICAL SYSTEMA6E931001001205
*1: Back-up current is the constant flow of current present (for the audio unit, clock, PCM, etc.) when the engine
switch is off and with the key removed.
*
2: Must not be 0 A.
*3: Cold area
End Of Sie
CLUTCHA6E931001024201
End Of Sie
MANUAL TRANSAXLEA6E931001024202
ItemSpecification
Diesel engine
MZR-CD (RF Turbo)
BatteryElectrolyte gravity 1.27—1.29
Back-up current*
1(mA) Max.20
Type
95D31L, 115D31L
*3
Test load chart (A) Battery type95D31L (64) 250
115D31L (70) *3320
Slow-charge (A)Battery type
(5-hour rate)95D31L (64) 6.5—8.0
115D31L (70)
*37.0—8.5
Quick-charge
Battery type
(5-hour rate)95D31L (64) 40
(A/30 min)
115D31L (70)
*345
GeneratorStandard voltage (V)Ignition switch ON TerminalBB+
L Approx. 1
SB+
Idle [20°C {68°F}] TerminalB
14.1—14.7 L
S
Generated current*
2
(reference) (A) Engine speed (rpm)1,000 0—80
2,000 0—90
Starter No load testVoltage (V) 11
Current (A) Below 130
Item Specification
Clutch coverDiaphragm
spring fingersDepth mm {in} 0.6 {0.024}
Misalignment mm {in} 0.6 {0.024}
Maximum clearance of flatness of the
pressure platemm {in} 0.3 {0.012}
Flywheel Run out limit mm {in} 0.3 {0.012}
Item Specification
Manual transaxle typeA65M-R
Transaxle controlFloor-shift
Operation systemCable
Shift assistSynchromesh
Gear ratio1st 3.416
2nd 1.944
3rd 1.258
4th 0.902
5th 0.659
Reverse 3.252
Final gear ratio3.588
Transaxle oilGrade API service GL-4 or GL-5
Viscosity (All-season) SAE 75W-90
Capacity (approximate quantity)
2.30 {2.40, 2.00}
(L {US qt, Imp qt})
