2002 LAND ROVER DISCOVERY Clutch plate

CONTENTS
12 CONTENTS
Operation ........................................................................................................................................ 41-19
ADJUSTMENTS
Cable - high/low selector ................................................................................................................ 41-21
REPAIRS
Bottom cover - transfer box ......................................................................................................... 41-23
Transfer box - Diesel ...................................................................................................................... 41-24
Transfer box - V8 ............................................................................................................................ 41-27
Gasket - rear cover plate ................................................................................................................ 41-30
Switch - differential lock - Up to 03 MY ........................................................................................... 41-30
Cable - high/low selector ................................................................................................................ 41-31
Oil seal - input shaft ...................................................................................................................... 41-32
Seal - front output shaft .................................................................................................................. 41-33
Seal - rear output shaft ................................................................................................................... 41-34
Gasket - rear output shaft housing ................................................................................................. 41-35
Solenoid - interlock - Up to 03 MY .................................................................................................. 41-36
Sensor - neutral ........................................................................................................................... 41-36
Sensor - oil temperature ................................................................................................................ 41-37
Switch - high low - warning ........................................................................................................... 41-37
OVERHAUL
Intermediate gear assembly ......................................................................................................... 41-39
Differential assembly ................................................................................................................... 41-42
Dog clutch - differential lock .......................................................................................................... 41-57
Input gear/bearing .......................................................................................................................... 41-60
Low gear - differential ................................................................................................................... 41-62
AUTOMATIC GEARBOX - ZF4HP22 - 24 ................................................ 44-1
DESCRIPTION AND OPERATION
Automatic gearbox component layout ............................................................................................ 44-1
Control schematic ........................................................................................................................... 44-2
Description ...................................................................................................................................... 44-4
Operation ........................................................................................................................................ 44-17
ADJUSTMENTS
Cable - selector ............................................................................................................................. 44-21
Stall test .......................................................................................................................................... 44-21
REPAIRS
Cable and lever assembly - selector .............................................................................................. 44-23
Selector indicator .......................................................................................................................... 44-24
Switch - starter inhibitor ................................................................................................................. 44-24
Seal - selector shaft ........................................................................................................................ 44-25
Gearbox - convertor and transfer gearbox - Diesel ....................................................................... 44-26
Gearbox - convertor and transfer gearbox - V8 ............................................................................ 44-30
Torque converter and oil seal ......................................................................................................... 44-34
Housing - torque converter ............................................................................................................ 44-35
Gasket - intermediate plate ............................................................................................................ 44-37
Intermediate plate .......................................................................................................................... 44-38
Pump - fluid .................................................................................................................................... 44-40
Seal - rear extension housing ......................................................................................................... 44-41
Gasket - rear extension housing. .................................................................................................. 44-42
Parking pawl assembly. ................................................................................................................ 44-43
Gasket - oil sump ........................................................................................................................... 44-44
Filter - oil ........................................................................................................................................ 44-45
Cooler - fluid - Td5 .......................................................................................................................... 44-45

GENERAL DATA
04-10
Cooling system - V8
Clutch - Td5
Type Pressurised, spill return, thermostatically controlled water and
antifreeze mixture. Vertical flow radiator with remote header tank
and pump assisted
Cooling fans 9 blade axial flow on viscous coupling and 11 blade axial flow
electric
Electric cooling fan switching points:
For A/C system:

On When vehicle speed is 50 mph (80 km/h) or less and ambient
temperature is 28 °C (82 °F) or more

Off When vehicle speed increases to (62.5 mph (100 km/h) or
ambient temperature decreases to 25 °C (77 °F)
For engine cooling during normal running:

On 100 °C (212 °F)

Off 94.5 °C (202 °F)
For engine cooling at ignition off (to counteract heat
soak):

On If, within 10 seconds of ignition off, intake air temperature is 60 °C
(140 °F) or more and engine coolant temperature is 110 °C (230
°F) or more

Off After 10 minutes or if engine coolant temperature decreases to
100 °C (212 °F)
Coolant pump Centrifugal impeller, belt driven from crankshaft
Coolant pump drive ratio 1.293 : 1
Coolant pump output at 1000 rev/min 10 litres/min (2.64 US galls/min) at 0.7 bar (10 lbf.in
2)
Thermostat Waxstat with pressure relief valve
Thermostat operating temperature:

Initial opening 82 °C (179 °F)

Fully open 96 °C (204 °F)
Expansion tank cap relief valve - system operating
pressure1.4 bar (20 lbf.in
2)
Type Diaphragm spring, hydraulically operated with self-centering,
preloaded release bearing
Drive plate diameter 267 mm (10.5118 in)
Pressure plate diameter 267 mm (10.5118 in)
Clutch plate friction material Verto F202
Diaphragm finger height when clamped on a 8.5 mm
(0.33 in) thick gauge plate42.5 to 48.5 mm (1.673 to 1.904 in)
Diaphragm finger clearance (service limit) 1.00 mm (0.040 in)
Clutch plate thickness under 6500 N (1461 lb) axial
load:

New 8.2 to 8.8 mm (0.33 to 0.34 in)

Service limit 7.0 mm (0.27 in)

GENERAL DATA
04-11
Clutch - V8
Type Diaphragm spring, hydraulically operated with self-centering,
preloaded release bearing
Clutch plate friction material APTEC 385
Drive plate diameter 267 mm (10.5118 in)
Pressure plate diameter 268 mm (10.5512 in)
Clutch plate thickness (clamped state)

New 8.4-8.9 mm (0.33-0.35 in)

Service limit 7.1 mm (0.28 in)
Rivet depth:

New 1.73 mm (0.07 in)

Service limit 0.25 mm (0.01 in)
Clutch plate runout:

New 0.5 mm (0.02 in)

Service limit 0.5 mm (0.02 in)

TORQUE WRENCH SETTINGS
06-8
Manual gearbox - R380
Transfer box - LT230SE
Note: † New Patchlok nut must be fitted.
TORQUE DESCRIPTION METRIC IMPERIAL
Bias plate bolts25 Nm (18 lbf.ft)
Gearbox to engine bolts 45 Nm (33 lbf.ft)
Coolant pipe housing bolts 25 Nm (18 lbf.ft)
Breather pipe banjo bolt 15 Nm (11 lbf.ft)
Gear lever extension clamp bolt 25 Nm (18 lbf.ft)
Gearbox mounting bolts 85 Nm (63 lbf.ft)
Gearbox mounting nuts 48 Nm (37 lbf.ft)
Seal housing bolts 18 Nm (13 lbf.ft)
Bearing sleeve bolts 25 Nm (18 lbf.ft)
Fork bolt7 Nm (5.2 lbf.ft)
Reverse light switch 24 Nm (18 lbf.ft)
Extension housing bolts 25 Nm (18 lbf.ft)
Gear selector housing bolts 25 Nm (18 lbf.ft)
Oil pump to housing Torx screws 6 Nm (4.4 lbf.ft)
Gear change lever yoke Allen screw 25 Nm (18 lbf.ft)
5th gear stake nut 350 Nm (258 lbf.ft)
Spool retainer bolts 8 Nm (6 lbf.ft)
Centre plate detent spring and ball Torx screw 25 Nm (18 lbf.ft)
Selector lever to housing bolts 25 Nm (18 lbf.ft)
Clutch Bell housing bolts 73 Nm (54 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
High/low selector cable 30 Nm (22 lbf.ft)
Bottom plate bolts 25 Nm (18 lbf.ft)
Transfer box to gearbox 45 Nm (33 lbf.ft)
Rear cover plate25 Nm (18 lbf.ft)
Differential lock warning lamp switch locknut - Up to 03 MY
11 Nm(8 lbf.ft)
Differential lock warning lamp switches - 03 MY onwards
25 Nm (18 lbf.ft)
Drive flange nut148 Nm (109 lbf.ft)
Output shaft housing 45 Nm (33 lbf.ft)
Oil temperature sensor 42 Nm (31 lbf.ft)
Inhibitor switch to transfer box 26 Nm (19 lbf.ft)
Intermediate shaft nut †88 Nm (65 lbf.ft)
Side cover bolts25 Nm (18 lbf.ft)
Bearing retaining nut 72 Nm (53 lbf.ft)
Output flange nut 162 Nm (119 lbf.ft)
Selector housing bolts 25 Nm (18 lbf.ft)
Bearing housing/cover bolts 25 Nm (18 lbf.ft)

ENGINE - TD5
DESCRIPTION AND OPERATION 12-1-3
1Oil dipstick tube
2Screw – oil dipstick tube to camshaft carrier
3Oil dipstick
42nd piston ring
5Piston
6Small-end bush
7Connecting rod
8Big-end bearing cap
9Connecting rod bolt (2 off per connecting rod)
10Top piston ring
11Oil control ring
12Circlips (2 off per gudgeon pin)
13Gudgeon pin
14Big-end bearing shells
15Dowels – cylinder head (2 off)
16Clutch housing shim plate
17 Crankshaft rear oil seal and housing
18Screws – crankshaft seal housing to engine
block (5 off)
19Bolts – clutch housing shim plate to engine
block (2 off)
20Main oil gallery plug (rear)
21Oil filter adaptor gasket
22Oil filter adaptor thermostat
23Oil filter adaptor assembly
24Oil filter adaptor insert25Oil filter adaptor to cylinder block bolts (3 off)
26Oil filter
27Oil pressure switch
28Oil cooler banjo bolts (2 off)
29O-rings – oil cooler banjo bolts (2 off)
30Oil cooler to cylinder block bolts (7 off)
31Centrifuge assembly
32Centrifuge to cylinder block bolts (3 off)
33Centrifuge oil drain pipe
34Oil drain pipe to sump gasket
35Centrifuge to oil drain pipe gasket
36Oil cooler plugs (3 off)
37Oil cooler assembly
38Oil cooler matrix 'O-rings' (2 off)
39Oil cooler matrix
40Oil cooler gasket
41Coolant and PAS pump assembly bracket
42Bracket bolts (5 off + 1 stud/nut)
43Cylinder block
44Dowels to timing block cover (2 off)
45Oil gallery delivery plug
46Cross drilling plug
47Coolant jacket plug
48Core plugs (3 off)

ENGINE - TD5
12-1-56 REPAIRS
Flywheel
$% 12.53.07
Remove
1.Remove clutch assembly.

+ CLUTCH - Td5, REPAIRS, Clutch
assembly.
2.Remove and discard 8 bolts securing flywheel
to crankshaft and remove flywheel.
Refit
1.Clean flywheel and mating face.
2.Position flywheel to crankshaft, fit new bolts
and working in a diagonal sequence tighten to
40 Nm (30 lbf.ft), then a further 90
°.
CAUTION: Do not carry out stages 1 and 2 in
one operation.
3.Fit clutch assembly.

+ CLUTCH - Td5, REPAIRS, Clutch
assembly.
Plate - drive - automatic
$% 12.53.13
Remove
1.Remove gearbox.

+ AUTOMATIC GEARBOX - ZF4HP22
- 24, REPAIRS, Gearbox - convertor and
transfer gearbox - Diesel.
2.Remove and discard 8 bolts and remove
converter drive plate, spacer and starter ring
gear.
Refit
1.Clean drive plate, spacer and starter ring gear.
2.Fit starter ring gear, spacer and drive plate to
crankshaft, fit new bolts and working in a
diagonal sequence tighten to 40 Nm (30 lbf.ft),
then a further 90
°.
CAUTION: Do not carry out stages 1 and 2 in
one operation.
3.Refit gearbox.

+ AUTOMATIC GEARBOX - ZF4HP22
- 24, REPAIRS, Gearbox - convertor and
transfer gearbox - Diesel.

ENGINE - V8
REPAIRS 12-2-31
Flywheel
$% 12.53.07
Remove
1.Remove gearbox

+ MANUAL GEARBOX - R380,
REPAIRS, Gearbox - V8.
2.Restrain flywheel.
3.Working in sequence, progressively slacken 6
bolts securing clutch cover to flywheel.
Remove bolts.
4.Remove clutch cover.
5.Remove clutch plate.
6.Release crankshaft sensor multiplug from
bracket.
7.Remove 2 bolts securing crankshaft sensor
cover. 8.Remove crankshaft sensor cover.
9.Remove 2 nuts securing crankshaft sensor.
10.Remove crankshaft sensor.
11.Remove 6 bolts securing flywheel.
12.Remove flywheel.
On early engines, balance weights are on
engine side of flywheel; replacement flywheels
will have balance weights on clutch side of
flywheel.
Refit
1.Clean mating faces of flywheel and crankshaft,
dowel and dowel hole.
2.Fit flywheel to crankshaft and tighten bolts to
78 Nm (58 lbf.ft).
3.Clean crankshaft sensor and mating face.
4.Fit crankshaft sensor and tighten nuts to 6 Nm
(4.4 lbf.ft).
5.Fit crankshaft sensor cover and tighten bolts to
6 Nm (5 lbf.ft).
6.Fit crankshaft sensor multiplug to bracket.
7.Clean clutch cover, drive plate and spigot bush
in end of crankshaft. Renew worn components
as necessary.
8.If refitting existing drive plate, apply 'Molycote
FB 180' to splines.

ENGINE - V8
12-2-32 REPAIRS
9.Fit alignment tool LRT-12-001 to spigot
bearing in crankshaft.
10.Fit drive plate onto tool LRT-12-001 ensure
side marked 'flywheel side' is towards flywheel.
11.Fit clutch cover and locate on dowels.
12.Fit clutch cover bolts and tighten in diagonal
sequence to 40 Nm (30 lbf.ft).
13.Fit gearbox assembly.

+ MANUAL GEARBOX - R380,
REPAIRS, Gearbox - V8.
Plate - drive - automatic
$% 12.53.13
Remove
1.Remove automatic gearbox.

+ AUTOMATIC GEARBOX - ZF4HP22
- 24, REPAIRS, Gearbox - convertor and
transfer gearbox - V8.
2.Remove 2 bolts securing CKP sensor cover.
3.Remove CKP sensor cover.
4.Remove 2 nuts securing CKP sensor.
5.Remove CKP sensor.