2002 JEEP LIBERTY vehicle speed sensor

(M)Malfunction Indicator Lamp (MIL) illuminated during engine operation if this DTC was recorded
(depending if required by CARB and/or EPA). MIL is displayed as an engine icon on instrument panel.
(G)Generator lamp illuminated
Generic Scan
Tool P-CodeDRB Scan Tool Display Brief Description of DTC
P0712 (M) Trans Temp Sensor Voltage Too Low Voltage less than 1.55 volts (4-speed auto. trans. only).
P0713 Trans Temp Sensor Voltage Too
HighTransmission fluid temperature sensor input above
acceptable voltage. Was MIL code 37.
P0713 (M) Trans Temp Sensor Voltage Too
HighVoltage greater than 3.76 volts (4-speed auto. trans.
only).
P0720 (M) Low Output SPD Sensor RPM,
Above 15 MPHThe relationship between the Output Shaft Speed Sensor
and vehicle speed is not within acceptable limits.
P0720 (M) Low Output Spd Sensor RPM Above
15 mphOutput shaft speed is less than 60 rpm with vehicle speed
above 15 mph (4-speed auto. trans. only).
P0740 (M) Torq Con Clu, No RPM Drop at
LockupRelationship between engine and vehicle speeds
indicated failure of torque convertor clutch lock-up system
(TCC/PTU solenoid)
P0743 (M) Torque Converter Clutch Solenoid/
Trans Relay CircuitsAn open or shorted condition detected in the torque
converter clutch (part throttle unlock) solenoid control
circuit. Shift solenoid C electrical fault - Aisin transmission
P0743 (M) Torque Converter Clutch Solenoid/
Trans Relay CircuitsAn open or shorted condition detected in the torque
converter part throttle unlock solenoid control circuit (3 or
4-speed auto. trans. only).
P0748 (M) Governor Pressur Sol Control/Trans
Relay CircuitsAn open or shorted condition detected in the Governor
Pressure Solenoid circuit or Trans Relay Circuit in JTEC
RE transmissions.
P0748 (M) Governor Pressure Sol Control/Trans
Relay CircuitsAn open or shorted condition detected in the governor
pressure solenoid or relay circuits (4-speed auto. trans.
only).
P0751 (M) O/D Switch Pressed (Lo) More Than
5 MinutesOverdrive override switch input is in a prolonged
depressed state.
P0751 (M) O/D Switch Pressed (LO) More Than
5 MinOverdrive Off switch input too low for more than 5
minutes (4-speed auto. trans. only).
P0753 (M) Trans 3-4 Shift Sol/Trans Relay
CircuitsAn open or shorted condition detected in the overdrive
solenoid control circuit or Trans Relay Circuit in JTEC RE
transmissions. Was MIL code 45.
P0753 (M) Trans 3-4 Shift Sol/Trans Relay
CircuitsAn open or shorted condition detected in the transmission
2-4 shift solenoid circuit (4-speed auto. trans. only).
P0756 AW4 Shift Sol B (2-3) Functional
FailureShift solenoid B (2-3) functional fault - Aisin transmission
P0783 (M) 3-4 Shift Sol, No RPM Drop at
LockupThe overdrive solenoid is unable to engage the gear
change from 3rd gear to the overdrive gear.
P0801 Reverse Gear Lockout Circuit Open
or ShortAn open or shorted condition detected in the transmission
reverse gear lock-out solenoid control circuit.
P0830 Clutch Depressed Switch Circuit Problem detected in clutch switch circuit.
P0833 Clutch Released Switch Circuit Problem detected in clutch switch circuit.
P0836 4WD Mux Switch Circuit
P0837 4WD Mux Switch Performance
25 - 10 EMISSIONS CONTROLKJ
EMISSIONS CONTROL (Continued)

LEAK DETECTION PUMP MONITOR (IF EQUIPPED)
The leak detection assembly incorporates two pri-
mary functions: it must detect a leak in the evapora-
tive system and seal the evaporative system so the
leak detection test can be run.
The primary components within the assembly are:
A three port solenoid that activates both of the func-
tions listed above; a pump which contains a switch,
two check valves and a spring/diaphragm, a canister
vent valve (CVV) seal which contains a spring loaded
vent seal valve.
Immediately after a cold start, between predeter-
mined temperature thresholds limits, the three port
solenoid is briefly energized. This initializes the
pump by drawing air into the pump cavity and also
closes the vent seal. During non test conditions the
vent seal is held open by the pump diaphragm
assembly which pushes it open at the full travel posi-
tion. The vent seal will remain closed while the
pump is cycling due to the reed switch triggering of
the three port solenoid that prevents the diaphragm
assembly from reaching full travel. After the brief
initialization period, the solenoid is de-energized
allowing atmospheric pressure to enter the pump
cavity, thus permitting the spring to drive the dia-
phragm which forces air out of the pump cavity and
into the vent system. When the solenoid is energized
and de energized, the cycle is repeated creating flow
in typical diaphragm pump fashion. The pump is con-
trolled in 2 modes:
Pump Mode:The pump is cycled at a fixed rate to
achieve a rapid pressure build in order to shorten the
overall test length.
Test Mode:The solenoid is energized with a fixed
duration pulse. Subsequent fixed pulses occur when
the diaphragm reaches the Switch closure point.
The spring in the pump is set so that the system
will achieve an equalized pressure of about 7.5º
water. The cycle rate of pump strokes is quite rapid
as the system begins to pump up to this pressure. As
the pressure increases, the cycle rate starts to drop
off. If there is no leak in the system, the pump would
eventually stop pumping at the equalized pressure. If
there is a leak, it will continue to pump at a rate rep-
resentative of the flow characteristic of the size of the
leak. From this information we can determine if the
leak is larger than the required detection limit (cur-
rently set at .040º orifice by CARB). If a leak is
revealed during the leak test portion of the test, the
test is terminated at the end of the test mode and no
further system checks will be performed.
After passing the leak detection phase of the test,
system pressure is maintained by turning on the
LDP's solenoid until the purge system is activated.
Purge activation in effect creates a leak. The cycle
rate is again interrogated and when it increases dueto the flow through the purge system, the leak check
portion of the diagnostic is complete.
The canister vent valve will unseal the system
after completion of the test sequence as the pump
diaphragm assembly moves to the full travel position.
Evaporative system functionality will be verified by
using the stricter evap purge flow monitor. At an
appropriate warm idle the LDP will be energized to
seal the canister vent. The purge flow will be clocked
up from some small value in an attempt to see a
shift in the 02 control system. If fuel vapor, indicated
by a shift in the 02 control, is present the test is
passed. If not, it is assumed that the purge system is
not functioning in some respect. The LDP is again
turned off and the test is ended.
MISFIRE MONITOR
Excessive engine misfire results in increased cata-
lyst temperature and causes an increase in HC emis-
sions. Severe misfires could cause catalyst damage.
To prevent catalytic convertor damage, the PCM
monitors engine misfire.
The Powertrain Control Module (PCM) monitors
for misfire during most engine operating conditions
(positive torque) by looking at changes in the crank-
shaft speed. If a misfire occurs the speed of the
crankshaft will vary more than normal.
FUEL SYSTEM MONITOR
To comply with clean air regulations, vehicles are
equipped with catalytic converters. These converters
reduce the emission of hydrocarbons, oxides of nitro-
gen and carbon monoxide. The catalyst works best
when the Air Fuel (A/F) ratio is at or near the opti-
mum of 14.7 to 1.
The PCM is programmed to maintain the optimum
air/fuel ratio of 14.7 to 1. This is done by making
short term corrections in the fuel injector pulse width
based on the O2S sensor output. The programmed
memory acts as a self calibration tool that the engine
controller uses to compensate for variations in engine
specifications, sensor tolerances and engine fatigue
over the life span of the engine. By monitoring the
actual fuel-air ratio with the O2S sensor (short term)
and multiplying that with the program long-term
(adaptive) memory and comparing that to the limit,
it can be determined whether it will pass an emis-
sions test. If a malfunction occurs such that the PCM
cannot maintain the optimum A/F ratio, then the
MIL will be illuminated.
CATALYST MONITOR
To comply with clean air regulations, vehicles are
equipped with catalytic converters. These converters
reduce the emission of hydrocarbons, oxides of nitro-
gen and carbon monoxide.
25 - 18 EMISSIONS CONTROLKJ
EMISSIONS CONTROL (Continued)

COMPASS CALIBRATION - STANDARD
PROCEDURE.........................8M-2
COMPASS DEMAGNETIZING -
STANDARD PROCEDURE...............8M-2
COMPASS MINI-TRIP COMPUTER -
DIAGNOSIS AND TESTING..............8M-6
COMPASS MINI-TRIP ILLUMINATION
BULB - INSTALLATION................8L-75
COMPASS MINI-TRIP ILLUMINATION
BULB - REMOVAL....................8L-74
COMPASS VARIATION ADJUSTMENT -
STANDARD PROCEDURE...............8M-3
COMPASS/MINI-TRIP COMPUTER -
DESCRIPTION........................8M-4
COMPASS/MINI-TRIP COMPUTER -
INSTALLATION.......................8M-8
COMPASS/MINI-TRIP COMPUTER -
OPERATION.........................8M-5
COMPASS/MINI-TRIP COMPUTER -
REMOVAL...........................8M-7
COMPRESSION PRESSURE - DIAGNOSIS
AND TESTING, CYLINDER................9-8
COMPRESSOR CLUTCH - INSPECTION,
A/C................................24-14
COMPRESSOR CLUTCH - INSTALLATION,
A/C................................24-14
COMPRESSOR CLUTCH - REMOVAL, A/C . . 24-13
COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE, A/C...........24-12
COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING, A/C..........24-12
COMPRESSOR CLUTCH RELAY -
DESCRIPTION, A/C...................24-15
COMPRESSOR CLUTCH RELAY -
DIAGNOSIS AND TESTING.............24-15
COMPRESSOR CLUTCH RELAY -
INSTALLATION, A/C...................24-16
COMPRESSOR CLUTCH RELAY -
OPERATION, A/C.....................24-15
COMPRESSOR CLUTCH RELAY -
REMOVAL, A/C......................24-16
COMPRESSOR NOISE - DIAGNOSIS AND
TESTING, A/C.......................24-42
COMPUTER - DESCRIPTION, COMPASS/
MINI-TRIP..........................8M-4
COMPUTER - DIAGNOSIS AND TESTING,
COMPASS MINI-TRIP..................8M-6
COMPUTER - INSTALLATION, COMPASS/
MINI-TRIP..........................8M-8
COMPUTER - OPERATION, COMPASS/
MINI-TRIP..........................8M-5
COMPUTER - REMOVAL, COMPASS/
MINI-TRIP..........................8M-7
CONDENSER - DESCRIPTION, A/C.......24-45
CONDENSER - INSTALLATION, A/C.......24-46
CONDENSER - OPERATION, A/C.........24-45
CONDENSER - REMOVAL, A/C..........24-45
CONDITIONER - DESCRIPTION, HEATER
AND AIR ............................24-1
CONDITIONER - OPERATION, HEATER
AND AIR ............................24-2
CONDITIONS - DIAGNOSIS AND
TESTING, SPARK PLUG................8I-13
CONNECT FITTING - DESCRIPTION,
QUICK.............................14-10
CONNECTING ROD - DESCRIPTION,
PISTON.............................9-49
CONNECTING ROD BEARING - FITTING -
STANDARD PROCEDURE................9-40
CONNECTING ROD BEARING, FITTING.....9-49
CONNECTOR - DESCRIPTION, DATA LINK . 8E-10
CONNECTOR - INSTALLATION
.......8W-01-11
CONNECTOR - INSTALLATION, TRAILER
TOW
..............................8L-61
CONNECTOR - OPERATION, DATA LINK
. . . 8E-10
CONNECTOR - REMOVAL
...........8W-01-11
CONNECTOR - REMOVAL, TRAILER TOW
. . 8L-61
CONNECTOR, GROUND AND SPLICE
INFORMATION - DESCRIPTION
........8W-01-7
CONNECTOR/GROUND/SPLICE LOCATION
- DESCRIPTION
....................8W-91-1
CONSOLE - DESCRIPTION, OVERHEAD
....8M-1
CONSOLE - INSTALLATION, FLOOR
.....23-158
CONSOLE - OPERATION, OVERHEAD
......8M-2
CONSOLE - REMOVAL, FLOOR
.........23-158
CONSOLE DUCT - INSTALLATION, FLOOR
. 24-31
CONSOLE DUCT - REMOVAL, FLOOR
.....24-31CONSOLE LID LATCH - INSTALLATION,
FLOOR............................23-158
CONSOLE LID LATCH - REMOVAL,
FLOOR............................23-158
CONSOLE, REMOVAL - OVERHEAD.......8M-4
CONTAINER - DESCRIPTION, COOLANT
RECOVERY PRESS....................7-19
CONTAINER - OPERATION, COOLANT
RECOVERY PRESS....................7-19
CONTAMINATION - DIAGNOSIS AND
TESTING, BRAKE FLUID................5-26
CONTAMINATION - DIAGNOSIS AND
TESTING, FLUID....................21-125
CONTINUITY - STANDARD PROCEDURE,
TESTING.........................8W-01-9
CONTROL - DESCRIPTION, A/C HEATER . . . 24-16
CONTROL - DESCRIPTION, IGNITION......8I-1
CONTROL - DESCRIPTION, SPEED........8P-1
CONTROL - INSTALLATION, A/C HEATER . . 24-17
CONTROL - OPERATION, IGNITION........8I-1
CONTROL - OPERATION, SPEED..........8P-1
CONTROL - REMOVAL, A/C HEATER......24-17
CONTROL - TORQUE, SPEED............8P-2
CONTROL ARM - DESCRIPTION, LOWER . . . 2-21
CONTROL ARM - INSTALLATION, LOWER . . 2-10,
2-21
CONTROL ARM - INSTALLATION, UPPER . . . 2-21
CONTROL ARM - OPERATION, LOWER.....2-21
CONTROL ARM - REMOVAL, LOWER . . 2-10,2-21
CONTROL ARM - REMOVAL, UPPER......2-20
CONTROL ASSEMBLY WINDOW
DEFOGGER FUNCTION - DIAGNOSIS
AND TESTING, REAR HVAC.............8G-9
CONTROL CABLE - INSTALLATION,
THROTTLE..........................14-46
CONTROL CABLE - REMOVAL,
THROTTLE..........................14-45
CONTROL ILLUMINATION BULB -
INSTALLATION, HEATER-A/C............8L-78
CONTROL ILLUMINATION BULB -
REMOVAL, HEATER-A/C...............8L-78
CONTROL INFORMATION (VECI) LABEL -
DESCRIPTION, VEHICLE EMISSION.....Intro.-8
CONTROL MODULE - DESCRIPTION,
AIRBAG.............................8O-9
CONTROL MODULE - DESCRIPTION,
BODY...............................8E-2
CONTROL MODULE - DESCRIPTION,
SIDE IMPACT AIRBAG.................8O-43
CONTROL MODULE - DESCRIPTION,
TRANSMISSION......................8E-18
CONTROL MODULE - DIAGNOSIS AND
TESTING, BODY.......................8E-7
CONTROL MODULE - INSTALLATION....23-183
CONTROL MODULE - INSTALLATION,
AIRBAG............................8O-12
CONTROL MODULE - INSTALLATION,
BODY...............................8E-7
CONTROL MODULE - INSTALLATION,
SIDE IMPACT AIRBAG.................8O-45
CONTROL MODULE - OPERATION,
AIRBAG............................8O-10
CONTROL MODULE - OPERATION, BODY . . . 8E-5
CONTROL MODULE - OPERATION, SIDE
IMPACT AIRBAG.....................8O-43
CONTROL MODULE - OPERATION,
TRANSMISSION......................8E-18
CONTROL MODULE - REMOVAL........23-183
CONTROL MODULE - REMOVAL, AIRBAG . 8O-11
CONTROL MODULE - REMOVAL, BODY....8E-7
CONTROL MODULE - REMOVAL, SIDE
IMPACT AIRBAG.....................8O-44
CONTROL MOTOR - DESCRIPTION, IDLE
AIR ...............................14-35
CONTROL MOTOR - INSTALLATION, IDLE
AIR ...............................14-36
CONTROL MOTOR - OPERATION, IDLE
AIR ...............................14-35
CONTROL MOTOR - REMOVAL, IDLE AIR . . 14-36
CONTROL RELAY - DESCRIPTION,
TRANSMISSION.....................21-168
CONTROL RELAY - OPERATION,
TRANSMISSION
.....................21-168
CONTROL SWITCH - DESCRIPTION
.....23-184
CONTROL SWITCH - DIAGNOSIS AND
TESTING
..........................23-184
CONTROL SWITCH - INSTALLATION
.....23-184
CONTROL SWITCH - OPERATION
.......23-184CONTROL SWITCH - REMOVAL........23-184
CONTROL SYSTEM - DESCRIPTION,
EMISSION...........................25-1
CONTROL SYSTEM - DESCRIPTION,
EVAPORATION.......................25-24
CONTROLLER ANTILOCK BRAKE -
INSTALLATION.......................8E-10
CONTROLLER ANTILOCK BRAKE -
REMOVAL..........................8E-10
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-2
CONVERTER - DESCRIPTION, TORQUE . . . 21-162
CONVERTER - INSPECTION, CATALYTIC....11-3
CONVERTER - INSTALLATION, CATALYTIC . . 11-3
CONVERTER - INSTALLATION, TORQUE . . 21-167
CONVERTER - OPERATION, TORQUE....21-166
CONVERTER - REMOVAL, CATALYTIC......11-2
CONVERTER - REMOVAL, TORQUE......21-167
CONVERTER HOUSING FLUID LEAK -
DIAGNOSIS AND TESTING.............21-80
COOLANT - DESCRIPTION, ENGINE........0-3
COOLANT LOW INDICATOR -
DESCRIPTION.......................8J-15
COOLANT LOW INDICATOR - OPERATION . 8J-16
COOLANT RECOVERY PRESS
CONTAINER - DESCRIPTION.............7-19
COOLANT RECOVERY PRESS
CONTAINER - OPERATION...............7-19
COOLANT TEMPERATURE SENSOR -
DESCRIPTION, ENGINE.................7-19
COOLANT TEMPERATURE SENSOR -
INSTALLATION, ENGINE................7-21
COOLANT TEMPERATURE SENSOR -
OPERATION, ENGINE...................7-20
COOLANT TEMPERATURE SENSOR -
REMOVAL, ENGINE....................7-20
COOLANT THERMOSTAT - OPERATION,
ENGINE.............................7-21
COOLER - DESCRIPTION, FLUID.........19-20
COOLER - DESCRIPTION, TRANS.........7-32
COOLER - INSTALLATION, FLUID........19-20
COOLER - OPERATION, FLUID..........19-20
COOLER - REMOVAL, FLUID............19-20
COOLING, SPECIAL TOOLS..............7-14
COOLING SYSTEM - OPERATION..........7-2
COOLING SYSTEM - REVERSE
FLUSHING - STANDARD PROCEDURE.....7-12
COOLING SYSTEM 3.7L ENGINE -
DESCRIPTION.........................7-1
COOLING SYSTEM 3.7L ENGINE -
STANDARD PROCEDURE, DRAINING......7-12
COOLING SYSTEM 3.7L ENGINE -
STANDARD PROCEDURE, REFILLING......7-12
COOLING SYSTEM DIAGNOSIS CHART -
DIAGNOSIS AND TESTING...............7-6
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-4
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION........................24-1
COOLING SYSTEM ROUTING 3.7L
ENGINE - DESCRIPTION.................7-2
CORE - DESCRIPTION, HEATER.........24-52
CORE - INSTALLATION, HEATER.........24-53
CORE - OPERATION, HEATER...........24-52
CORE - REMOVAL, HEATER............24-52
CORE AND OIL GALLERY PLUGS -
STANDARD PROCEDURE, ENGINE........9-10
COURTESY LAMP BULB - INSTALLATION . . 8L-76
COURTESY LAMP BULB - REMOVAL.....8L-75
COURTESY LAMP REPLACEMENT -
STANDARD PROCEDURE...............8M-2
COURTESY LAMP UNIT - INSTALLATION . . 8L-77
COURTESY LAMP UNIT - REMOVAL......8L-76
COVER - DESCRIPTION, STRUCTURAL.....9-55
COVER - FRONT - INSTALLATION, SEAT
BACK.............................23-167
COVER - FRONT - INSTALLATION, SEAT
CUSHION..........................23-167
COVER - FRONT - REMOVAL, SEAT BACK . 23-166
COVER - FRONT - REMOVAL, SEAT
CUSHION..........................23-167
COVER - INSTALLATION, COWL TRIM . . . 23-157
COVER - INSTALLATION, INSTRUMENT
PANEL TOP
........................23-153
COVER - INSTALLATION, STRUCTURAL
....9-55
COVER - OPERATION, STRUCTURAL
......9-55
COVER - REAR - INSTALLATION, SEAT
BACK
.............................23-169
COVER - REAR - REMOVAL, SEAT BACK
. 23-169
6 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

HVAC CONTROL ASSEMBLY WINDOW
DEFOGGER FUNCTION - DIAGNOSIS
AND TESTING, REAR..................8G-9
HVAC HOUSING - ASSEMBLY...........24-34
HVAC HOUSING - DISASSEMBLY........24-34
HVAC HOUSING - INSTALLATION........24-34
HVAC HOUSING - REMOVAL............24-33
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING..........9-19,9-30
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING.............21-79
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS....................21-100
HYDROMETER TEST - STANDARD
PROCEDURE........................8F-11
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-1
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-8
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-35
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-36
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-35
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-36
IDLER SHAFT - INSTALLATION...........9-77
IDLER SHAFT - REMOVAL...............9-77
IGNITION CIRCUIT SENSE -
DESCRIPTION.........................8E-13
IGNITION CIRCUIT SENSE - OPERATION . . 8E-15
IGNITION COIL - DESCRIPTION...........8I-9
IGNITION COIL - INSTALLATION.........8I-10
IGNITION COIL - OPERATION.............8I-9
IGNITION COIL - REMOVAL.............8I-10
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-16
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-16
IGNITION COIL CAPACITOR - OPERATION . . 8I-16
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-16
IGNITION COIL RESISTANCE, 2.4L.........8I-2
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-3
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION CONTROL - OPERATION.........8I-1
IGNITION SWITCH - DESCRIPTION........19-8
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-10
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-8
IGNITION SWITCH - DIAGNOSIS AND
TESTING, KEY-IN.....................19-10
IGNITION SWITCH INSTALLATION,
INSTALLATION........................19-9
IGNITION SWITCH REMOVAL, REMOVAL . . . 19-9
IGNITION SYSTEM - TORQUE............8I-3
IGNITION TIMING - SPECIFICATIONS......8I-2
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-14
ILLUMINATION BULB - INSTALLATION,
COMPASS MINI-TRIP
.................8L-75
ILLUMINATION BULB - INSTALLATION,
HEATER-A/C CONTROL
................8L-78
ILLUMINATION BULB - INSTALLATION,
TRANSMISSION RANGE INDICATOR
......8L-83
ILLUMINATION BULB - REMOVAL,
COMPASS MINI-TRIP
.................8L-74
ILLUMINATION BULB - REMOVAL,
HEATER-A/C CONTROL
................8L-78
ILLUMINATION BULB - REMOVAL,
TRANSMISSION RANGE INDICATOR
......8L-82
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY
........................8E-15
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY
........................8E-18
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY
........................8E-16
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY
........................8E-17
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE
..................8O-43
IMPACT AIRBAG CONTROL MODULE -
INSTALLATION, SIDE
.................8O-45
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE
....................8O-43IMPACT AIRBAG CONTROL MODULE -
REMOVAL, SIDE.....................8O-44
IMPACT SENSOR - DESCRIPTION,
FRONT.............................8O-21
IMPACT SENSOR - INSTALLATION,
FRONT.............................8O-22
IMPACT SENSOR - OPERATION, FRONT . . . 8O-21
IMPACT SENSOR - REMOVAL, FRONT....8O-22
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF............21-125
INDICATOR - DESCRIPTION, ABS........8J-11
INDICATOR - DESCRIPTION, AIRBAG.....8J-12
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-13
INDICATOR - DESCRIPTION, CHARGING . . . 8J-15
INDICATOR - DESCRIPTION, COOLANT
LOW...............................8J-15
INDICATOR - DESCRIPTION, CRUISE.....8J-16
INDICATOR - DESCRIPTION, DOOR AJAR . . 8J-17
INDICATOR - DESCRIPTION, FOUR LOW
MODE.............................8J-29
INDICATOR - DESCRIPTION, FRONT FOG
LAMP..............................8J-19
INDICATOR - DESCRIPTION, FULL TIME . . . 8J-29
INDICATOR - DESCRIPTION, GATE AJAR . . 8J-20
INDICATOR - DESCRIPTION, GLASS
AJAR..............................8J-21
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-22
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, LOW OIL
PRESSURE..........................8J-23
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, PART TIME . . 8J-29
INDICATOR - DESCRIPTION, REAR FOG
LAMP..............................8J-27
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SECURITY . . . 8J-28
INDICATOR - DESCRIPTION, SKIS........8J-31
INDICATOR - DESCRIPTION, TRANS
TEMP..............................8J-33
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-34
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-35
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-37
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-14
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID......................8J-36
INDICATOR - OPERATION, ABS..........8J-11
INDICATOR - OPERATION, AIRBAG.......8J-12
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-13
INDICATOR - OPERATION, CHARGING....8J-15
INDICATOR - OPERATION, COOLANT
LOW...............................8J-16
INDICATOR - OPERATION, CRUISE.......8J-17
INDICATOR - OPERATION, DOOR AJAR . . . 8J-17
INDICATOR - OPERATION, FOUR LOW
MODE.............................8J-30
INDICATOR - OPERATION, FRONT FOG
LAMP..............................8J-19
INDICATOR - OPERATION, FULL TIME....8J-30
INDICATOR - OPERATION, GATE AJAR....8J-20
INDICATOR - OPERATION, GLASS AJAR . . . 8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-22
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, LOW OIL
PRESSURE
..........................8J-23
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, PART TIME
....8J-29
INDICATOR - OPERATION, REAR FOG
LAMP
..............................8J-27
INDICATOR - OPERATION, SEATBELT
.....8J-28
INDICATOR - OPERATION, SECURITY
.....8J-28
INDICATOR - OPERATION, SKIS
.........8J-31
INDICATOR - OPERATION, TRANS TEMP
. . 8J-34
INDICATOR - OPERATION, TURN SIGNAL
. . 8J-34
INDICATOR - OPERATION, WAIT-TO-
START
.............................8J-35
INDICATOR - OPERATION, WASHER
FLUID
..............................8J-36INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-37
INDICATOR ILLUMINATION BULB -
INSTALLATION, TRANSMISSION
RANGE.............................8L-83
INDICATOR ILLUMINATION BULB -
REMOVAL, TRANSMISSION RANGE......8L-82
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-24
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-24
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INFLATION - DIAGNOSIS AND TESTING,
TIRE................................22-7
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-18
INITIALIZATION - STANDARD
PROCEDURE, SKIS....................8Q-8
INJECTION - DESCRIPTION, FUEL........14-29
INJECTOR - DESCRIPTION, FUEL........14-33
INJECTOR - DIAGNOSIS AND TESTING,
FUEL..............................14-33
INJECTOR - OPERATION, FUEL..........14-33
INLET FILTER - INSTALLATION..........14-28
INLET FILTER - REMOVAL..............14-28
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-4
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-138
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-133
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-135
INPUT CLUTCH ASSEMBLY - OPERATION . 21-135
INPUT SPEED SENSOR - DESCRIPTION . . 21-143
INPUT SPEED SENSOR - INSTALLATION . 21-143
INPUT SPEED SENSOR - OPERATION....21-143
INPUT SPEED SENSOR - REMOVAL.....21-143
INSTRUMENT CLUSTER - ASSEMBLY.....8J-10
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-7
INSTRUMENT CLUSTER - DISASSEMBLY . . . 8J-9
INSTRUMENT CLUSTER - INSTALLATION . . 8J-11
INSTRUMENT CLUSTER - OPERATION.....8J-4
INSTRUMENT CLUSTER - REMOVAL......8J-9
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-8
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-7
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION......................23-151
INSTRUMENT PANEL ASSEMBLY -
REMOVAL.........................23-149
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION......................23-154
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL.........................23-154
INSTRUMENT PANEL DRIVER SIDE
BEZELS - INSTALLATION..............23-154
INSTRUMENT PANEL DRIVER SIDE
BEZELS - REMOVAL.................23-153
INSTRUMENT PANEL END CAP -
INSTALLATION
......................23-153
INSTRUMENT PANEL END CAP -
REMOVAL
.........................23-153
INSTRUMENT PANEL PASSENGER SIDE
BEZEL - INSTALLATION
...............23-154
INSTRUMENT PANEL PASSENGER SIDE
BEZEL - REMOVAL
..................23-154
INSTRUMENT PANEL TOP COVER -
INSTALLATION
......................23-153
INSTRUMENT PANEL TOP COVER -
REMOVAL
.........................23-152
INTAKE AIR TEMPERATURE SENSOR -
DESCRIPTION
.......................14-36
INTAKE AIR TEMPERATURE SENSOR -
INSTALLATION
.......................14-38
INTAKE AIR TEMPERATURE SENSOR -
OPERATION
.........................14-36
INTAKE AIR TEMPERATURE SENSOR -
REMOVAL
..........................14-37
INTAKE MANIFOLD - DESCRIPTION
.......9-68
INTAKE MANIFOLD - INSTALLATION
.......9-69
INTAKE MANIFOLD - REMOVAL
..........9-68
KJINDEX 13
Description Group-Page Description Group-Page Description Group-Page

SEAL - INSTALLATION, REAR OUTPUT
SHAFT............................21-212
SEAL - NV1500 - INSTALLATION,
EXTENSION HOUSING.................21-32
SEAL - NV1500 - REMOVAL, EXTENSION
HOUSING...........................21-32
SEAL - NV3550 - INSTALLATION,
EXTENSION HOUSING.................21-74
SEAL - NV3550 - REMOVAL, EXTENSION
HOUSING...........................21-74
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL.....................9-48
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ................................9-48
SEAL - REMOVAL, ADAPTER HOUSING . . 21-124
SEAL - REMOVAL, A-PILLAR...........23-185
SEAL - REMOVAL, COWL/PLENUM......23-187
SEAL - REMOVAL, COWL/PLENUM
WINDOW BAFFLE...................23-187
SEAL - REMOVAL, FRONT OUTPUT
SHAFT......................21-208,21-246
SEAL - REMOVAL, GLASS PANEL.......23-178
SEAL - REMOVAL, OIL PUMP FRONT....21-152
SEAL - REMOVAL, PINION.....3-102,3-38,3-68
SEAL - REMOVAL, REAR OUTPUT SHAFT . 21-210
SEAL AREA LEAKS - DIAGNOSIS AND
TESTING, REAR.......................9-61
SEALER LOCATIONS - SPECIFICATIONS . . . 23-87
SEALS - DESCRIPTION, VALVE GUIDE . 9-29,9-38
SEALS - INSTALLATION, AXLE SHAFT....3-102,
3-38
SEALS - REMOVAL, AXLE SHAFT....3-101,3-37
SEAT - FRONT - INSTALLATION........23-165
SEAT - FRONT - REMOVAL............23-165
SEAT - REAR - INSTALLATION.........23-168
SEAT - REAR - REMOVAL.............23-168
SEAT BACK - FRONT - INSTALLATION . . . 23-166
SEAT BACK - FRONT - REMOVAL.......23-166
SEAT BACK - REAR - INSTALLATION....23-168
SEAT BACK - REAR - REMOVAL........23-168
SEAT BACK COVER - FRONT -
INSTALLATION......................23-167
SEAT BACK COVER - FRONT - REMOVAL . 23-166
SEAT BACK COVER - REAR -
INSTALLATION......................23-169
SEAT BACK COVER - REAR - REMOVAL . . 23-169
SEAT BACK CUSHION - FRONT -
INSTALLATION......................23-167
SEAT BACK CUSHION - FRONT -
REMOVAL.........................23-167
SEAT BACK CUSHION - REAR -
INSTALLATION......................23-170
SEAT BACK CUSHION - REAR -
REMOVAL.........................23-170
SEAT BACK FRAME - REAR -
INSTALLATION......................23-171
SEAT BACK FRAME - REAR - REMOVAL . . 23-171
SEAT BACK LATCH / LOCK -
INSTALLATION, FOLDING REAR........23-170
SEAT BACK LATCH / LOCK - REMOVAL,
FOLDING REAR.....................23-170
SEAT BACK LATCH STRIKER -
INSTALLATION, REAR................23-171
SEAT BACK LATCH STRIKER - REMOVAL,
REAR.............................23-170
SEAT BACK RECLINER - FRONT -
INSTALLATION......................23-166
SEAT BACK RECLINER - FRONT -
REMOVAL.........................23-166
SEAT BELT & RETRACTOR -
INSTALLATION, FRONT................8O-24
SEAT BELT & RETRACTOR -
INSTALLATION, REAR CENTER..........8O-33
SEAT BELT & RETRACTOR -
INSTALLATION, REAR OUTBOARD.......8O-34
SEAT BELT & RETRACTOR - REMOVAL,
FRONT.............................8O-23
SEAT BELT & RETRACTOR - REMOVAL,
REAR CENTER.......................8O-32
SEAT BELT & RETRACTOR - REMOVAL,
REAR OUTBOARD....................8O-33
SEAT BELT BUCKLE - INSTALLATION,
FRONT
.............................8O-26
SEAT BELT BUCKLE - INSTALLATION,
REAR
..............................8O-35
SEAT BELT BUCKLE - REMOVAL, FRONT
. . 8O-25
SEAT BELT BUCKLE - REMOVAL, REAR
. . . 8O-34
SEAT BELT SWITCH - DESCRIPTION
.....8O-35SEAT BELT SWITCH - OPERATION.......8O-36
SEAT BELT TENSIONER - DESCRIPTION . . . 8O-36
SEAT BELT TENSIONER - OPERATION....8O-36
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-38
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-37
SEAT CUSHION - FRONT -
INSTALLATION......................23-167
SEAT CUSHION - FRONT - REMOVAL....23-167
SEAT CUSHION - REAR - INSTALLATION . 23-171
SEAT CUSHION - REAR - REMOVAL.....23-171
SEAT CUSHION COVER - FRONT -
INSTALLATION......................23-167
SEAT CUSHION COVER - FRONT -
REMOVAL.........................23-167
SEAT CUSHION SIDE SHIELDS -
INSTALLATION......................23-167
SEAT CUSHION SIDE SHIELDS -
REMOVAL.........................23-167
SEAT ELEMENT - DESCRIPTION, HEATED . 8G-13
SEAT ELEMENT - DIAGNOSIS AND
TESTING, HEATED....................8G-13
SEAT ELEMENT - OPERATION, HEATED . . . 8G-13
SEAT HEATER SWITCH - DESCRIPTION,
DRIVER............................8G-11
SEAT HEATER SWITCH - DESCRIPTION,
PASSENGER........................8G-14
SEAT HEATER SWITCH - INSTALLATION,
DRIVER............................8G-13
SEAT HEATER SWITCH - INSTALLATION,
PASSENGER........................8G-15
SEAT HEATER SWITCH - OPERATION,
DRIVER............................8G-12
SEAT HEATER SWITCH - OPERATION,
PASSENGER........................8G-14
SEAT HEATER SWITCH - REMOVAL,
DRIVER............................8G-13
SEAT HEATER SWITCH - REMOVAL,
PASSENGER........................8G-15
SEAT MODULE - DESCRIPTION, HEATED . . 8E-21
SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED....................8E-22
SEAT MODULE - INSTALLATION, HEATED . . 8E-24
SEAT MODULE - OPERATION, HEATED....8E-21
SEAT MODULE - REMOVAL, HEATED.....8E-24
SEAT RISER - INSTALLATION, MANUAL . . 23-168
SEAT RISER - REMOVAL, MANUAL......23-167
SEAT SENSOR - DIAGNOSIS AND
TESTING, HEATED....................8G-14
SEAT SWITCH - DESCRIPTION, LEFT
POWER............................8N-16
SEAT SWITCH - DESCRIPTION, RIGHT
POWER............................8N-19
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED..............8G-12,8G-14
SEAT SWITCH - DIAGNOSIS AND
TESTING, LEFT POWER...............8N-17
SEAT SWITCH - DIAGNOSIS AND
TESTING, RIGHT POWER..............8N-19
SEAT SWITCH - INSTALLATION, LEFT
POWER............................8N-18
SEAT SWITCH - INSTALLATION, RIGHT
POWER............................8N-20
SEAT SWITCH - OPERATION, LEFT
POWER............................8N-17
SEAT SWITCH - OPERATION, RIGHT
POWER............................8N-19
SEAT SWITCH - REMOVAL, LEFT POWER . 8N-18
SEAT SWITCH - REMOVAL, RIGHT
POWER............................8N-20
SEAT SYSTEM - DESCRIPTION, HEATED . . 8G-10
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED
....................8G-11
SEAT SYSTEM - OPERATION, HEATED
....8G-10
SEAT TRACK - DESCRIPTION
...........8N-15
SEAT TRACK - DIAGNOSIS AND TESTING
. 8N-16
SEAT TRACK - INSTALLATION
..........23-168
SEAT TRACK - INSTALLATION
..........8N-16
SEAT TRACK - OPERATION
.............8N-15
SEAT TRACK - REMOVAL
.............23-168
SEAT TRACK - REMOVAL
..............8N-16
SEATBELT INDICATOR - DESCRIPTION
....8J-27
SEATBELT INDICATOR - OPERATION
......8J-28
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES
.....................9-26
SEATS - DESCRIPTION, POWER
.........8N-14SEATS - DIAGNOSIS AND TESTING,
POWER............................8N-15
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES.................9-28,9-36
SEATS - OPERATION, POWER..........8N-15
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .........................9-27,9-35
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT . . 8Q-3
SECURITY INDICATOR - DESCRIPTION....8J-28
SECURITY INDICATOR - OPERATION.....8J-28
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT..............8Q-6
SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL LEVEL.................14-9
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL.............14-9
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL............14-10
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL..........................14-9
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-9
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-13
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-15
SENSE - PCM INPUT - OPERATION, ASD . . . 8I-4
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - DESCRIPTION, AMBIENT
TEMP..............................8M-9
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-24
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-30
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-19
SENSOR - DESCRIPTION, FRONT
IMPACT............................8O-21
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - DESCRIPTION, INPUT SPEED . 21-143
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - DESCRIPTION, KNOCK........8I-11
SENSOR - DESCRIPTION, LINE
PRESSURE (LP)....................21-144
SENSOR - DESCRIPTION, MAP..........14-38
SENSOR - DESCRIPTION, OUTPUT
SPEED............................21-152
SENSOR - DESCRIPTION, OXYGEN.......14-40
SENSOR - DESCRIPTION, POSITION....21-209,
21-247
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-47
SENSOR - DESCRIPTION,
TRANSMISSION RANGE..............21-168
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE........21-170
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE...............8M-9
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-14
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-24
SENSOR - INSTALLATION, CRANKSHAFT
POSITION..........................14-32
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - INSTALLATION, FRONT
IMPACT............................8O-22
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-34
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT......................14-10
SENSOR - INSTALLATION, INPUT SPEED . 21-143
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE
......................14-38
SENSOR - INSTALLATION, KNOCK
........8I-12
SENSOR - INSTALLATION, LINE
PRESSURE (LP)
....................21-144
SENSOR - INSTALLATION, MAP
.........14-40
SENSOR - INSTALLATION, OUTPUT
SPEED
............................21-152
KJINDEX 23
Description Group-Page Description Group-Page Description Group-Page

TANK - REMOVAL, FUEL...............14-25
TANK CHECK VALVE - DESCRIPTION,
FUEL..............................14-28
TANK CHECK VALVE - INSTALLATION,
FUEL..............................14-28
TANK CHECK VALVE - OPERATION, FUEL . . 14-28
TANK CHECK VALVE - REMOVAL, FUEL . . . 14-28
TANK SKID PLATE - INSTALLATION,
FUEL...............................13-9
TANK SKID PLATE - REMOVAL, FUEL......13-9
TASK MANAGER - DESCRIPTION........25-17
TASK MANAGER - OPERATION..........25-21
TCM QUICK LEARN - STANDARD
PROCEDURE........................8E-21
TEMP INDICATOR - DESCRIPTION,
TRANS.............................8J-33
TEMP INDICATOR - OPERATION, TRANS . . 8J-34
TEMP SENSOR - DESCRIPTION,
AMBIENT...........................8M-9
TEMP SENSOR - OPERATION, AMBIENT . . . 8M-9
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-18
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-18
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-24
TEMPERATURE SENSOR - DESCRIPTION,
ENGINE COOLANT.....................7-19
TEMPERATURE SENSOR - DESCRIPTION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION.....................21-170
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT...............8M-9
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-24
TEMPERATURE SENSOR -
INSTALLATION, ENGINE COOLANT........7-21
TEMPERATURE SENSOR -
INSTALLATION, INTAKE AIR............14-38
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-24
TEMPERATURE SENSOR - OPERATION,
ENGINE COOLANT.....................7-20
TEMPERATURE SENSOR - OPERATION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION.....................21-170
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-24
TEMPERATURE SENSOR - REMOVAL,
ENGINE COOLANT.....................7-20
TEMPERATURE SENSOR - REMOVAL,
INTAKE AIR .........................14-37
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT.....8M-9
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-36
TENSIONER - OPERATION, SEAT BELT....8O-36
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN................14-3
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE....................14-16
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY.....................14-15
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE....................14-15
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE...............21-79
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-2
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-10
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-11
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-14
TEST - STANDARD PROCEDURE, LOAD . . . 8F-12
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE
...............8F-12
TEST - STANDARD PROCEDURE,
VERIFICATION
........................8O-8
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION
..........................25-2
TEST MODE - DESCRIPTION, STATE
DISPLAY
............................25-2
TESTER - STANDARD PROCEDURE,
USING MIDTRONICS ELECTRICAL
.......8F-15TETHER ANCHOR - DESCRIPTION, CHILD . 8O-13
TETHER ANCHOR - OPERATION, CHILD . . . 8O-13
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-3
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-6
THERMAL GUARD - DESCRIPTION.......8F-20
THERMAL GUARD - INSTALLATION......8F-20
THERMAL GUARD - OPERATION.........8F-20
THERMAL GUARD - REMOVAL..........8F-20
THERMOSTAT - DIAGNOSIS AND
TESTING............................7-21
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-21
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM..............21-81
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-4
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN............9-9
THROTTLE BODY - DESCRIPTION........14-43
THROTTLE BODY - INSTALLATION.......14-44
THROTTLE BODY - OPERATION.........14-43
THROTTLE BODY - REMOVAL...........14-43
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-46
THROTTLE CONTROL CABLE - REMOVAL . . 14-45
THROTTLE POSITION SENSOR -
DESCRIPTION.........................14-47
THROTTLE POSITION SENSOR -
INSTALLATION.......................14-48
THROTTLE POSITION SENSOR -
OPERATION.........................14-47
THROTTLE POSITION SENSOR -
REMOVAL..........................14-47
TIE ROD END - INSTALLATION..........19-16
TIE ROD END - REMOVAL..............19-16
TIE ROD END REMOVAL TOOL, SPECIAL
TOOLS - OUTER.....................19-15
TIME INDICATOR - DESCRIPTION, FULL . . . 8J-29
TIME INDICATOR - DESCRIPTION, PART . . 8J-29
TIME INDICATOR - OPERATION, FULL....8J-30
TIME INDICATOR - OPERATION, PART....8J-29
TIMING - DESCRIPTION, VALVE..........9-71
TIMING - OPERATION, VALVE............9-71
TIMING - SPECIFICATIONS, IGNITION......8I-2
TIMING BELT / CHAIN COVER(S) -
INSTALLATION........................9-76
TIMING BELT / CHAIN COVER(S) -
REMOVAL...........................9-74
TIMING CHAIN WEAR, STANDARD
PROCEDURE - MEASURING.............9-71
TIRE - INSTALLATION, SPARE...........22-9
TIRE - REMOVAL, SPARE...............22-8
TIRE INFLATION - DIAGNOSIS AND
TESTING............................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE ROTATION - STANDARD
PROCEDURE.........................22-2
TIRE &TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-6
TIRES - DESCRIPTION, RADIAL-PLY.......22-6
TIRES - DESCRIPTION, REPLACEMENT....22-7
TIRES AND WHEEL RUNOUT -
DIAGNOSIS AND TESTING..............22-1
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . . 8W-01-9
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-5
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER..........2-5
TOOL, SPECIAL TOOLS - OUTER TIE
ROD END REMOVAL..................19-15
TOOLS - 3.7L ENGINE, SPECIAL
..........9-15
TOOLS - 8 1/4 AXLE, SPECIAL
...........3-98
TOOLS - BASE BRAKES, SPECIAL
.........5-7
TOOLS - BODY, SPECIAL
................23-5
TOOLS - COOLING, SPECIAL
.............7-14TOOLS - FRONT AXLE, SPECIAL..........3-34
TOOLS - FRONT SUSPENSION, SPECIAL....2-8
TOOLS - FUEL SYSTEM, SPECIAL........14-6
TOOLS - OUTER TIE ROD END REMOVAL
TOOL, SPECIAL......................19-15
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-20
TOOLS - REAR AXLE, SPECIAL...........3-63
TOOLS - RFE TRANSMISSION, SPECIAL . . 21-120
TOOLS - STEERING COLUMN, SPECIAL....19-8
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, BATTERY SYSTEM - SPECIAL.....8F-7
TOOLS, SPECIFICATIONS - SPECIAL....3-12,3-6
TOOLS, SPECIFICATIONS - SPECIAL......8F-24
TOP COVER - INSTALLATION,
INSTRUMENT PANEL.................23-153
TOP COVER - REMOVAL, INSTRUMENT
PANEL............................23-152
TORQUE - SPECIFICATIONS.............13-6
TORQUE CHART, SPECIFICATIONS . . 19-15,19-19,
19-8
TORQUE CHART, SPECIFICATIONS.....2-17,2-8
TORQUE CONVERTER - DESCRIPTION . . . 21-162
TORQUE CONVERTER - INSTALLATION . . . 21-167
TORQUE CONVERTER - OPERATION.....21-166
TORQUE CONVERTER - REMOVAL......21-167
TORQUE, EXCEPT DIESEL..............8F-23
TORQUE, GAS POWERED..............8F-38
TORQUE, IGNITION SYSTEM.............8I-3
TORQUE REFERENCES - DESCRIPTION . . Intro.-7
TORQUE, SPECIFICATIONS...............5-7
TORQUE, SPECIFICATIONS..............7-13
TORQUE, SPECIFICATIONS.............25-26
TORQUE, SPECIFICATIONS..............9-12
TORQUE, SPECIFICATIONS..............14-5
TORQUE, SPEED CONTROL.............8P-2
TOUCH-UP - DESCRIPTION, PAINT......23-163
TOW CONNECTOR - INSTALLATION,
TRAILER...........................8L-61
TOW CONNECTOR - REMOVAL, TRAILER . . 8L-61
TOW HOOK - INSTALLATION, FRONT......13-8
TOW HOOK - INSTALLATION, REAR.......13-8
TOW HOOK - REMOVAL, FRONT..........13-8
TOW HOOK - REMOVAL, REAR...........13-8
TOW RELAY - DESCRIPTION, TRAILER....8L-61
TOW RELAY - DIAGNOSIS AND TESTING,
TRAILER...........................8L-62
TOW RELAY - INSTALLATION, TRAILER . . . 8L-64
TOW RELAY - OPERATION, TRAILER.....8L-62
TOW RELAY - REMOVAL, TRAILER.......8L-63
TOW WIRING - DESCRIPTION, TRAILER . . 8L-64
TOWING - STANDARD PROCEDURE........0-6
TRACK - DESCRIPTION, SEAT..........8N-15
TRACK - DIAGNOSIS AND TESTING,
SEAT ..............................8N-16
TRACK - INSTALLATION, SEAT.........23-168
TRACK - INSTALLATION, SEAT..........8N-16
TRACK - OPERATION, SEAT............8N-15
TRACK - REMOVAL, SEAT.............23-168
TRACK - REMOVAL, SEAT..............8N-16
TRAC-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-109,
3-77
TRAC-LOK - CLEANING, DIFFERENTIAL . . . 3-109,
3-77
TRAC-LOK - DISASSEMBLY,
DIFFERENTIAL...................3-107,3-75
TRAC-LOK - INSPECTION, DIFFERENTIAL . 3-109,
3-77
TRAC-LOKT- DIAGNOSIS AND TESTING . . 3-106,
3-74
TRAILER HITCH - INSTALLATION.........13-9
TRAILER HITCH - REMOVAL.............13-9
TRAILER TOW CONNECTOR -
INSTALLATION.......................8L-61
TRAILER TOW CONNECTOR - REMOVAL . . 8L-61
TRAILER TOW RELAY - DESCRIPTION....8L-61
TRAILER TOW RELAY - DIAGNOSIS AND
TESTING...........................8L-62
TRAILER TOW RELAY - INSTALLATION . . . 8L-64
TRAILER TOW RELAY - OPERATION......8L-62
TRAILER TOW RELAY - REMOVAL
.......8L-63
TRAILER TOW WIRING - DESCRIPTION
. . . 8L-64
TRANS COOLER - DESCRIPTION
.........7-32
TRANS TEMP INDICATOR -
DESCRIPTION
.......................8J-33
TRANS TEMP INDICATOR - OPERATION
. . . 8J-34
KJINDEX 27
Description Group-Page Description Group-Page Description Group-Page

VALVE - INSTALLATION, FLOW
MANAGEMENT.......................14-7
VALVE - INSTALLATION, FRONT CHECK....8R-9
VALVE - INSTALLATION, FUEL TANK
CHECK.............................14-28
VALVE - INSTALLATION, PCV...........25-32
VALVE - INSTALLATION, REAR CHECK....8R-35
VALVE - INSTALLATION, VACUUM CHECK . 24-28
VALVE - OPERATION, FLOW
MANAGEMENT.......................14-6
VALVE - OPERATION, FRONT CHECK......8R-9
VALVE - OPERATION, FUEL TANK CHECK . . 14-28
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - OPERATION, PCV..............25-31
VALVE - OPERATION, REAR CHECK......8R-34
VALVE - OPERATION, SOLENOID SWITCH . 21-161
VALVE - OPERATION, VACUUM CHECK....24-28
VALVE - REMOVAL, FLOW
MANAGEMENT.......................14-6
VALVE - REMOVAL, FRONT CHECK.......8R-9
VALVE - REMOVAL, FUEL TANK CHECK . . . 14-28
VALVE - REMOVAL, PCV...............25-32
VALVE - REMOVAL, REAR CHECK.......8R-34
VALVE - REMOVAL, VACUUM CHECK.....24-28
VALVE BODY - ASSEMBLY............21-176
VALVE BODY - CLEANING.............21-175
VALVE BODY - DESCRIPTION............21-171
VALVE BODY - DISASSEMBLY..........21-173
VALVE BODY - INSPECTION...........21-175
VALVE BODY - INSTALLATION..........21-177
VALVE BODY - OPERATION............21-171
VALVE BODY - REMOVAL.............21-172
VALVE GUIDE SEALS - DESCRIPTION . . 9-29,9-38
VALVE GUIDES - DESCRIPTION......9-19,9-30
VALVE SPRINGS - DESCRIPTION.....9-29,9-38
VALVE SPRINGS - INSTALLATION.....9-29,9-38
VALVE SPRINGS - REMOVAL........9-29,9-38
VALVE TIMING - DESCRIPTION...........9-71
VALVE TIMING - OPERATION............9-71
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST.................9-28,9-36
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST.................9-27,9-35
VANITY LAMP BULB - INSTALLATION.....8L-84
VANITY LAMP BULB - REMOVAL........8L-83
VAPOR CANISTER - DESCRIPTION.......25-33
VAPOR CANISTER - INSTALLATION......25-33
VAPOR CANISTER - OPERATION.........25-33
VAPOR CANISTER - REMOVAL..........25-33
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-3
VEHICLE EMISSION CONTROL
INFORMATION (VECI) LABEL -
DESCRIPTION......................Intro.-8
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-8
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION.....................Intro.-9
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-3
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-6
VERIFICATION TEST - STANDARD
PROCEDURE.........................8O-8
VIBRATION - DIAGNOSIS AND TESTING,
TIRE NOISE OR.......................22-8
VIBRATION DAMPER - INSTALLATION.....9-55
VIBRATION DAMPER - REMOVAL.........9-54
VIEW MIRROR - INSTALLATION, SIDE . . . 23-145
VIEW MIRROR - REMOVAL, REAR......23-161
VIEW MIRROR - REMOVAL, SIDE.......23-145
VISCOUS - CLEANING, RADIATOR - FAN . . . 7-29
VISCOUS - DESCRIPTION, RADIATOR -
FAN ................................7-27
VISCOUS - INSPECTION, RADIATOR -
FAN ................................7-29
VISCOUS - INSTALLATION, RADIATOR -
FAN
................................7-29
VISCOUS - OPERATION, RADIATOR -
FAN
................................7-27
VISCOUS - REMOVAL, RADIATOR - FAN
....7-28
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING
............................7-28
VISOR - INSTALLATION, SUN
..........23-160VISOR - REMOVAL, SUN..............23-160
VISOR SUPPORT - INSTALLATION, SUN . . 23-160
VISOR SUPPORT - REMOVAL, SUN.....23-160
VOLT SUPPLIES - DESCRIPTION, 5......8E-13
VOLT SUPPLIES - OPERATION, 5........8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION....8F-31
VOLTAGE REGULATOR - OPERATION.....8F-31
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-12
VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-148
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-35
WAIT-TO-START INDICATOR -
OPERATION.........................8J-35
WARNING - INSTALLATION............23-173
WARNING - REMOVAL...............23-173
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-39
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-173
WARNING, BRAKES - BASE..............5-2
WARNING, CLUTCH.....................6-2
WARNING, FRONT......................2-7
WARNING, REAR......................2-16
WARNING, RESTRAINT SYSTEM.........8O-5
WARNING SYSTEM - DESCRIPTION,
CHIME..............................8B-1
WARNING SYSTEM - DIAGNOSIS AND
TESTING, CHIME......................8B-6
WARNING SYSTEM - OPERATION,
CHIME..............................8B-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-39
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-35
WASHER FLUID INDICATOR -
DIAGNOSIS AND TESTING..............8J-36
WASHER FLUID INDICATOR -
OPERATION.........................8J-36
WASHER FLUID LEVEL SWITCH -
DESCRIPTION.......................8R-17
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-18
WASHER FLUID LEVEL SWITCH -
OPERATION.........................8R-17
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-17
WASHER HOSES/TUBES - DESCRIPTION,
FRONT.............................8R-10
WASHER HOSES/TUBES - DESCRIPTION,
REAR..............................8R-35
WASHER HOSES/TUBES - OPERATION,
FRONT.............................8R-10
WASHER HOSES/TUBES - OPERATION,
REAR..............................8R-36
WASHER NOZZLE - DESCRIPTION,
FRONT.............................8R-11
WASHER NOZZLE - DESCRIPTION, REAR . 8R-36
WASHER NOZZLE - INSTALLATION,
FRONT.............................8R-11
WASHER NOZZLE - INSTALLATION,
REAR..............................8R-37
WASHER NOZZLE - OPERATION, FRONT . . 8R-11
WASHER NOZZLE - OPERATION, REAR . . . 8R-36
WASHER NOZZLE - REMOVAL, FRONT....8R-11
WASHER NOZZLE - REMOVAL, REAR....8R-36
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-18
WASHER PUMP/MOTOR - INSTALLATION . 8R-20
WASHER PUMP/MOTOR - OPERATION . . . 8R-19
WASHER PUMP/MOTOR - REMOVAL.....8R-19
WASHER RESERVOIR - DESCRIPTION....8R-21
WASHER RESERVOIR - INSTALLATION . . . 8R-22
WASHER RESERVOIR - OPERATION
......8R-21
WASHER RESERVOIR - REMOVAL
.......8R-21
WASHER SYSTEM - CLEANING, FRONT
WIPER
..............................8R-7
WASHER SYSTEM - CLEANING, REAR
WIPER
.............................8R-32
WASHER SYSTEM - DIAGNOSIS AND
TESTING, FRONT WIPER
...............8R-6WASHER SYSTEM - DIAGNOSIS AND
TESTING, REAR WIPER...............8R-30
WASHER SYSTEM - INSPECTION, FRONT
WIPER..............................8R-7
WASHER SYSTEM - INSPECTION, REAR
WIPER.............................8R-33
WATER DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING . . 23-176
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - DESCRIPTION...........7-29
WATER PUMP - OPERATION.............7-30
WATERDAM - INSTALLATION....23-126,23-133
WATERDAM - REMOVAL........23-126,23-133
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-37
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-37
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-8
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-71
WEATHERSTRIP - INSTALLATION, COWL . 23-185
WEATHERSTRIP - INSTALLATION, DOOR
LOWER...........................23-186
WEATHERSTRIP - INSTALLATION, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - INSTALLATION,
SWING GATE BELTLINE...............23-186
WEATHERSTRIP - INSTALLATION,
SWING GATE OPENING...............23-186
WEATHERSTRIP - REMOVAL, COWL.....23-185
WEATHERSTRIP - REMOVAL, DOOR
LOWER...........................23-186
WEATHERSTRIP - REMOVAL, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - REMOVAL, SWING
GATE BELTLINE.....................23-186
WEATHERSTRIP - REMOVAL, SWING
GATE OPENING.....................23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE RAIL............23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, WINDSHIELD A-PILLAR . . 23-187
WEATHERSTRIP/RETAINER - REMOVAL,
SIDE RAIL.........................23-186
WEATHERSTRIP/RETAINER - REMOVAL,
WINDSHIELD A-PILLAR...............23-186
WELD AND STRUCTURAL ADHESIVE
LOCATIONS - SPECIFICATIONS...........23-9
WHEEL - INSTALLATION, STEERING......19-12
WHEEL - REMOVAL, STEERING.........19-12
WHEEL ALIGNMENT - DESCRIPTION.......2-3
WHEEL ALIGNMENT - OPERATION.........2-3
WHEEL BALANCING - STANDARD
PROCEDURE.........................22-4
WHEEL CYLINDERS - ASSEMBLY.........5-29
WHEEL CYLINDERS - CLEANING.........5-28
WHEEL CYLINDERS - DISASSEMBLY......5-28
WHEEL CYLINDERS - INSPECTION........5-29
WHEEL CYLINDERS - INSTALLATION......5-29
WHEEL CYLINDERS - REMOVAL..........5-28
WHEEL MOUNTING - STANDARD
PROCEDURE........................22-10
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, FRONT...............23-145
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, REAR................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, FRONT...................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, REAR....................23-145
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-10
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRES......................22-1
WHEEL SPEED SENSOR -
INSTALLATION, FRONT
.................5-34
WHEEL SPEED SENSOR -
INSTALLATION, REAR
..................5-35
WHEEL SPEED SENSOR - REMOVAL,
FRONT
..............................5-34
WHEEL SPEED SENSOR - REMOVAL,
REAR
...............................5-35
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT
...............23-143
KJINDEX 29
Description Group-Page Description Group-Page Description Group-Page