2002 JEEP LIBERTY coolant level

DIAGNOSIS AND TESTING - HEATER
PERFORMANCE
Before performing the following tests, refer to Cool-
ing for the procedures to check the radiator coolant
level, serpentine drive belt tension, radiator air flow
and the radiator fan operation. Also be certain that
the accessory vacuum supply line is connected at the
engine intake manifold.
MAXIMUM HEATER OUTPUT
Engine coolant is delivered to the heater core
through two heater hoses. With the engine idling atnormal operating temperature, set the temperature
control knob in the full hot position, the mode control
switch knob in the floor heat position, and the blower
motor switch knob in the highest speed position.
Using a test thermometer, check the temperature of
the air being discharged at the HVAC housing floor
outlets. Compare the test thermometer reading to the
Temperature Reference chart.
Temperature Reference
Ambient Air Temperature15.5É C
(60É F)21.1É C
(70É F)26.6É C
(80É F)32.2É C
(90É F)
Minimum Air Temperature at
Floor Outlet52.2É C
(126É F)56.1É C
(133É F)59.4É C
(139É F)62.2É C
(144É F)
If the floor outlet air temperature is too low, refer
to Cooling to check the engine coolant temperature
specifications. Both of the heater hoses should be hot
to the touch. The coolant return heater hose should
be slightly cooler than the coolant supply heater
hose. If the return hose is much cooler than the sup-
ply hose, locate and repair the engine coolant flow
obstruction in the cooling system. Refer to Cooling
for the procedures.
OBSTRUCTED COOLANT FLOW Possible loca-
tions or causes of obstructed coolant flow:
²Pinched or kinked heater hoses.
²Improper heater hose routing.
²Plugged heater hoses or supply and return ports
at the cooling system connections.
²A plugged heater core.
If proper coolant flow through the cooling system is
verified, and heater outlet air temperature is still
low, a mechanical problem may exist.
MECHANICAL PROBLEMS Possible locations or
causes of insufficient heat:
²An obstructed cowl air intake.
²Obstructed heater system outlets.
²A blend door not functioning properly.
TEMPERATURE CONTROL
If the heater outlet air temperature cannot be
adjusted with the temperature control knob on theA/C Heater control panel, the following could require
service:
²The A/C Heater control.
²The blend door actuator.
²The blend door.
²Improper engine coolant temperature.
DIAGNOSIS AND TESTING - VACUUM SYSTEM
Vacuum control is used to operate the mode doors
in the heater-only and a/c heater housings. Testing of
the heater-only and A/C Heater mode control switch
operation will determine if the vacuum, electrical,
and mechanical controls are functioning. However, it
is possible that a vacuum control system that oper-
ates perfectly at engine idle (high engine vacuum)
may not function properly at high engine speeds or
loads (low engine vacuum). This can be caused by
leaks in the vacuum system, or a faulty vacuum
check valve.
A vacuum system test will help to identify the
source of poor vacuum system performance or vac-
uum system leaks. Before starting this test, stop the
engine and make certain that the problem is not a
disconnected vacuum supply tube at the engine
intake manifold vacuum tap or at the vacuum reser-
voir.
24 - 6 HEATING & AIR CONDITIONINGKJ
HEATING & AIR CONDITIONING (Continued)

HVAC CONTROL ASSEMBLY WINDOW
DEFOGGER FUNCTION - DIAGNOSIS
AND TESTING, REAR..................8G-9
HVAC HOUSING - ASSEMBLY...........24-34
HVAC HOUSING - DISASSEMBLY........24-34
HVAC HOUSING - INSTALLATION........24-34
HVAC HOUSING - REMOVAL............24-33
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING..........9-19,9-30
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING.............21-79
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS....................21-100
HYDROMETER TEST - STANDARD
PROCEDURE........................8F-11
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-1
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-8
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-35
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-36
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-35
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-36
IDLER SHAFT - INSTALLATION...........9-77
IDLER SHAFT - REMOVAL...............9-77
IGNITION CIRCUIT SENSE -
DESCRIPTION.........................8E-13
IGNITION CIRCUIT SENSE - OPERATION . . 8E-15
IGNITION COIL - DESCRIPTION...........8I-9
IGNITION COIL - INSTALLATION.........8I-10
IGNITION COIL - OPERATION.............8I-9
IGNITION COIL - REMOVAL.............8I-10
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-16
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-16
IGNITION COIL CAPACITOR - OPERATION . . 8I-16
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-16
IGNITION COIL RESISTANCE, 2.4L.........8I-2
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-3
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION CONTROL - OPERATION.........8I-1
IGNITION SWITCH - DESCRIPTION........19-8
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-10
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-8
IGNITION SWITCH - DIAGNOSIS AND
TESTING, KEY-IN.....................19-10
IGNITION SWITCH INSTALLATION,
INSTALLATION........................19-9
IGNITION SWITCH REMOVAL, REMOVAL . . . 19-9
IGNITION SYSTEM - TORQUE............8I-3
IGNITION TIMING - SPECIFICATIONS......8I-2
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-14
ILLUMINATION BULB - INSTALLATION,
COMPASS MINI-TRIP
.................8L-75
ILLUMINATION BULB - INSTALLATION,
HEATER-A/C CONTROL
................8L-78
ILLUMINATION BULB - INSTALLATION,
TRANSMISSION RANGE INDICATOR
......8L-83
ILLUMINATION BULB - REMOVAL,
COMPASS MINI-TRIP
.................8L-74
ILLUMINATION BULB - REMOVAL,
HEATER-A/C CONTROL
................8L-78
ILLUMINATION BULB - REMOVAL,
TRANSMISSION RANGE INDICATOR
......8L-82
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY
........................8E-15
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY
........................8E-18
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY
........................8E-16
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY
........................8E-17
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE
..................8O-43
IMPACT AIRBAG CONTROL MODULE -
INSTALLATION, SIDE
.................8O-45
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE
....................8O-43IMPACT AIRBAG CONTROL MODULE -
REMOVAL, SIDE.....................8O-44
IMPACT SENSOR - DESCRIPTION,
FRONT.............................8O-21
IMPACT SENSOR - INSTALLATION,
FRONT.............................8O-22
IMPACT SENSOR - OPERATION, FRONT . . . 8O-21
IMPACT SENSOR - REMOVAL, FRONT....8O-22
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF............21-125
INDICATOR - DESCRIPTION, ABS........8J-11
INDICATOR - DESCRIPTION, AIRBAG.....8J-12
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-13
INDICATOR - DESCRIPTION, CHARGING . . . 8J-15
INDICATOR - DESCRIPTION, COOLANT
LOW...............................8J-15
INDICATOR - DESCRIPTION, CRUISE.....8J-16
INDICATOR - DESCRIPTION, DOOR AJAR . . 8J-17
INDICATOR - DESCRIPTION, FOUR LOW
MODE.............................8J-29
INDICATOR - DESCRIPTION, FRONT FOG
LAMP..............................8J-19
INDICATOR - DESCRIPTION, FULL TIME . . . 8J-29
INDICATOR - DESCRIPTION, GATE AJAR . . 8J-20
INDICATOR - DESCRIPTION, GLASS
AJAR..............................8J-21
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-22
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, LOW OIL
PRESSURE..........................8J-23
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, PART TIME . . 8J-29
INDICATOR - DESCRIPTION, REAR FOG
LAMP..............................8J-27
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SECURITY . . . 8J-28
INDICATOR - DESCRIPTION, SKIS........8J-31
INDICATOR - DESCRIPTION, TRANS
TEMP..............................8J-33
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-34
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-35
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-37
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-14
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID......................8J-36
INDICATOR - OPERATION, ABS..........8J-11
INDICATOR - OPERATION, AIRBAG.......8J-12
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-13
INDICATOR - OPERATION, CHARGING....8J-15
INDICATOR - OPERATION, COOLANT
LOW...............................8J-16
INDICATOR - OPERATION, CRUISE.......8J-17
INDICATOR - OPERATION, DOOR AJAR . . . 8J-17
INDICATOR - OPERATION, FOUR LOW
MODE.............................8J-30
INDICATOR - OPERATION, FRONT FOG
LAMP..............................8J-19
INDICATOR - OPERATION, FULL TIME....8J-30
INDICATOR - OPERATION, GATE AJAR....8J-20
INDICATOR - OPERATION, GLASS AJAR . . . 8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-22
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, LOW OIL
PRESSURE
..........................8J-23
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, PART TIME
....8J-29
INDICATOR - OPERATION, REAR FOG
LAMP
..............................8J-27
INDICATOR - OPERATION, SEATBELT
.....8J-28
INDICATOR - OPERATION, SECURITY
.....8J-28
INDICATOR - OPERATION, SKIS
.........8J-31
INDICATOR - OPERATION, TRANS TEMP
. . 8J-34
INDICATOR - OPERATION, TURN SIGNAL
. . 8J-34
INDICATOR - OPERATION, WAIT-TO-
START
.............................8J-35
INDICATOR - OPERATION, WASHER
FLUID
..............................8J-36INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-37
INDICATOR ILLUMINATION BULB -
INSTALLATION, TRANSMISSION
RANGE.............................8L-83
INDICATOR ILLUMINATION BULB -
REMOVAL, TRANSMISSION RANGE......8L-82
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-24
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-24
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INFLATION - DIAGNOSIS AND TESTING,
TIRE................................22-7
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-18
INITIALIZATION - STANDARD
PROCEDURE, SKIS....................8Q-8
INJECTION - DESCRIPTION, FUEL........14-29
INJECTOR - DESCRIPTION, FUEL........14-33
INJECTOR - DIAGNOSIS AND TESTING,
FUEL..............................14-33
INJECTOR - OPERATION, FUEL..........14-33
INLET FILTER - INSTALLATION..........14-28
INLET FILTER - REMOVAL..............14-28
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-4
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-138
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-133
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-135
INPUT CLUTCH ASSEMBLY - OPERATION . 21-135
INPUT SPEED SENSOR - DESCRIPTION . . 21-143
INPUT SPEED SENSOR - INSTALLATION . 21-143
INPUT SPEED SENSOR - OPERATION....21-143
INPUT SPEED SENSOR - REMOVAL.....21-143
INSTRUMENT CLUSTER - ASSEMBLY.....8J-10
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-7
INSTRUMENT CLUSTER - DISASSEMBLY . . . 8J-9
INSTRUMENT CLUSTER - INSTALLATION . . 8J-11
INSTRUMENT CLUSTER - OPERATION.....8J-4
INSTRUMENT CLUSTER - REMOVAL......8J-9
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-8
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-7
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION......................23-151
INSTRUMENT PANEL ASSEMBLY -
REMOVAL.........................23-149
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION......................23-154
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL.........................23-154
INSTRUMENT PANEL DRIVER SIDE
BEZELS - INSTALLATION..............23-154
INSTRUMENT PANEL DRIVER SIDE
BEZELS - REMOVAL.................23-153
INSTRUMENT PANEL END CAP -
INSTALLATION
......................23-153
INSTRUMENT PANEL END CAP -
REMOVAL
.........................23-153
INSTRUMENT PANEL PASSENGER SIDE
BEZEL - INSTALLATION
...............23-154
INSTRUMENT PANEL PASSENGER SIDE
BEZEL - REMOVAL
..................23-154
INSTRUMENT PANEL TOP COVER -
INSTALLATION
......................23-153
INSTRUMENT PANEL TOP COVER -
REMOVAL
.........................23-152
INTAKE AIR TEMPERATURE SENSOR -
DESCRIPTION
.......................14-36
INTAKE AIR TEMPERATURE SENSOR -
INSTALLATION
.......................14-38
INTAKE AIR TEMPERATURE SENSOR -
OPERATION
.........................14-36
INTAKE AIR TEMPERATURE SENSOR -
REMOVAL
..........................14-37
INTAKE MANIFOLD - DESCRIPTION
.......9-68
INTAKE MANIFOLD - INSTALLATION
.......9-69
INTAKE MANIFOLD - REMOVAL
..........9-68
KJINDEX 13
Description Group-Page Description Group-Page Description Group-Page

LATCH - ACCESS PANEL - REMOVAL....23-139
LATCH - INSTALLATION . . 23-120,23-124,23-131,
23-137
LATCH - INSTALLATION, FLIP-UP GLASS . 23-136
LATCH - INSTALLATION, FLOOR
CONSOLE LID......................23-158
LATCH - INSTALLATION, GLOVE BOX....23-148
LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT BACK...........23-170
LATCH / LOCK - REMOVAL, FOLDING
REAR SEAT BACK...................23-170
LATCH - REMOVAL......23-120,23-124,23-131,
23-137
LATCH - REMOVAL, FLIP-UP GLASS.....23-136
LATCH - REMOVAL, FLOOR CONSOLE
LID...............................23-158
LATCH - REMOVAL, GLOVE BOX........23-148
LATCH RELEASE CABLE - INSTALLATION . 23-120
LATCH RELEASE CABLE - REMOVAL....23-120
LATCH RELEASE HANDLE -
INSTALLATION......................23-120
LATCH RELEASE HANDLE - REMOVAL . . . 23-120
LATCH STRIKER - INSTALLATION......23-124,
23-132,23-137
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-149
LATCH STRIKER - INSTALLATION, REAR
SEAT BACK........................23-171
LATCH STRIKER - REMOVAL....23-124,23-132,
23-137
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-148
LATCH STRIKER - REMOVAL, REAR
SEAT BACK........................23-170
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID...........21-80
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL..........................9-60
LEAK DETECTION PUMP - DESCRIPTION . . 25-27
LEAK DETECTION PUMP - INSTALLATION . 25-28
LEAK DETECTION PUMP - OPERATION....25-28
LEAK DETECTION PUMP - REMOVAL.....25-28
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-3
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE.......9-8
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-4
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-68
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-61
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-8
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-21
LEFT POWER SEAT SWITCH -
DESCRIPTION.......................8N-16
LEFT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-17
LEFT POWER SEAT SWITCH -
INSTALLATION......................8N-18
LEFT POWER SEAT SWITCH -
OPERATION
.........................8N-17
LEFT POWER SEAT SWITCH - REMOVAL
. . 8N-18
LEFT SIDE - INSTALLATION
.........2-12,2-15
LEFT SIDE - REMOVAL
.............2-11,2-15
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID
........21-125
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-54
LEVEL - STANDARD PROCEDURES,
MASTER CYLINDER FLUID
..............5-26
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
.................21-126
LEVEL SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL
.......................14-9
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
...................14-9
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
.................14-10
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
.....................14-9
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-9LEVEL SWITCH - DESCRIPTION,
WASHER FLUID.....................8R-17
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-18
LEVEL SWITCH - OPERATION, WASHER
FLUID.............................8R-17
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-17
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP.........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LEVER - INSTALLATION................5-31
LEVER - INSTALLATION, SHIFT . . . 21-214,21-249
LEVER - REMOVAL....................5-31
LEVER - REMOVAL, SHIFT......21-213,21-248
LHD - INSTALLATION...............8W-97-6
LHD - REMOVAL....................8W-97-5
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LID LATCH - INSTALLATION, FLOOR
CONSOLE..........................23-158
LID LATCH - REMOVAL, FLOOR
CONSOLE..........................23-158
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITS - DESCRIPTION, HIGH AND LOW . . 25-20
LINE - DESCRIPTION, REFRIGERANT.....24-38
LINE - INSTALLATION, A/C DISCHARGE . . . 24-47
LINE - INSTALLATION, A/C LIQUID.......24-47
LINE - INSTALLATION, A/C SUCTION.....24-49
LINE - REMOVAL, A/C DISCHARGE.......24-46
LINE - REMOVAL, A/C LIQUID...........24-47
LINE - REMOVAL, A/C SUCTION.........24-48
LINE AND HOSES - DIAGNOSIS AND
TESTING, BRAKE.......................5-8
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-144
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-144
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-144
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-144
LINES - DESCRIPTION, BRAKE............5-8
LINES - DESCRIPTION, FUEL...........14-10
LINES - DESCRIPTION, VACUUM........25-33
LINK - INSTALLATION, STABILIZER.......2-14
LINK - REMOVAL, STABILIZER...........2-14
LINK CONNECTOR - DESCRIPTION, DATA . 8E-10
LINK CONNECTOR - OPERATION, DATA . . . 8E-10
LINKAGE - INSTALLATION................6-9
LINKAGE - REMOVAL...................6-8
LINKAGE - STANDARD PROCEDURE,
STEERING..........................19-16
LIQUID LINE - INSTALLATION, A/C.......24-47
LIQUID LINE - REMOVAL, A/C...........24-47
LOAD TEST - STANDARD PROCEDURE....8F-12
LOAD VALUE - DESCRIPTION
...........25-20
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-4
LOCATIONS - SPECIFICATIONS, SEALER
. . 23-87LOCATIONS - SPECIFICATIONS, WELD
AND STRUCTURAL ADHESIVE...........23-9
LOCK - INSTALLATION, FOLDING REAR
SEAT BACK LATCH..................23-170
LOCK - REMOVAL, FOLDING REAR SEAT
BACK LATCH.......................23-170
LOCK / UNLOCK SWITCH -
INSTALLATION, DOOR.................8N-5
LOCK / UNLOCK SWITCH - REMOVAL,
DOOR..............................8N-4
LOCK CYLINDER - INSTALLATION......23-125,
23-138
LOCK CYLINDER - INSTALLATION.......19-11
LOCK CYLINDER - REMOVAL....23-125,23-137
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, DOOR.....8N-5
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-5
LOCK MOTOR - OPERATION, DOOR.......8N-5
LOCK OUT - ADJUSTMENT..............5-30
LOCK RELAY - DESCRIPTION, DOOR......8N-6
LOCK RELAY - DIAGNOSIS AND
TESTING, DOOR......................8N-6
LOCK RELAY - INSTALLATION, DOOR.....8N-7
LOCK RELAY - OPERATION, DOOR........8N-6
LOCK RELAY - REMOVAL, DOOR.........8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8Q-9
LOCK SWITCH - DESCRIPTION,
TAILGATE CYLINDER...................8N-9
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8Q-10
LOCK SWITCH - DIAGNOSIS AND
TESTING, TAILGATE CYLINDER..........8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - INSTALLATION,
TAILGATE CYLINDER..................8N-10
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - OPERATION, TAILGATE
CYLINDER...........................8N-9
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - REMOVAL, TAILGATE
CYLINDER..........................8N-10
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-3
LOCK/UNLOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR..................8N-4
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-38
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-37
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP
.........................8L-40
LOW FUEL INDICATOR - DESCRIPTION
. . . 8J-22
LOW FUEL INDICATOR - OPERATION
.....8J-22
LOW INDICATOR - DESCRIPTION,
COOLANT
...........................8J-15
LOW INDICATOR - OPERATION,
COOLANT
...........................8J-16
LOW LIMITS - DESCRIPTION, HIGH
......25-20
LOW MODE INDICATOR - DESCRIPTION,
FOUR
..............................8J-29
LOW MODE INDICATOR - OPERATION,
FOUR
..............................8J-30
LOW OIL PRESSURE INDICATOR -
DESCRIPTION
.......................8J-23
LOW OIL PRESSURE INDICATOR -
OPERATION
.........................8J-23
LOW PRESSURE SWITCH -
DESCRIPTION, A/C
...................24-18
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C
...................24-19
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-19
KJINDEX 15
Description Group-Page Description Group-Page Description Group-Page

REAR SEAT BACK LATCH STRIKER -
INSTALLATION......................23-171
REAR SEAT BACK LATCH STRIKER -
REMOVAL.........................23-170
REAR SEAT BELT BUCKLE -
INSTALLATION......................8O-35
REAR SEAT BELT BUCKLE - REMOVAL . . . 8O-34
REAR SUSPENSION - DIAGNOSIS AND
TESTING............................2-17
REAR TOW HOOK - INSTALLATION.......13-8
REAR TOW HOOK - REMOVAL...........13-8
REAR VIEW MIRROR - REMOVAL.......23-161
REAR WASHER HOSES/TUBES -
DESCRIPTION.......................8R-35
REAR WASHER HOSES/TUBES -
OPERATION.........................8R-36
REAR WASHER NOZZLE - DESCRIPTION . . 8R-36
REAR WASHER NOZZLE - INSTALLATION . 8R-37
REAR WASHER NOZZLE - OPERATION....8R-36
REAR WASHER NOZZLE - REMOVAL.....8R-36
REAR WHEEL OPENING FLARE
MOLDINGS - INSTALLATION...........23-145
REAR WHEEL OPENING FLARE
MOLDINGS - REMOVAL..............23-145
REAR WHEEL SPEED SENSOR -
INSTALLATION........................5-35
REAR WHEEL SPEED SENSOR -
REMOVAL...........................5-35
REAR WHEELHOUSE SPLASH SHIELD -
INSTALLATION......................23-144
REAR WHEELHOUSE SPLASH SHIELD -
REMOVAL.........................23-144
REAR WINDOW DEFOGGER -
DESCRIPTION........................8G-3
REAR WINDOW DEFOGGER -
OPERATION..........................8G-3
REAR WINDOW DEFOGGER GRID -
DESCRIPTION........................8G-5
REAR WINDOW DEFOGGER GRID -
DIAGNOSIS AND TESTING..............8G-5
REAR WINDOW DEFOGGER GRID -
OPERATION..........................8G-5
REAR WINDOW DEFOGGER RELAY -
DESCRIPTION........................8G-6
REAR WINDOW DEFOGGER RELAY -
DIAGNOSIS AND TESTING..............8G-6
REAR WINDOW DEFOGGER RELAY -
INSTALLATION.......................8G-7
REAR WINDOW DEFOGGER RELAY -
OPERATION..........................8G-6
REAR WINDOW DEFOGGER RELAY -
REMOVAL...........................8G-7
REAR WINDOW DEFOGGER SWITCH -
DESCRIPTION........................8G-8
REAR WINDOW DEFOGGER SWITCH -
DIAGNOSIS AND TESTING..............8G-8
REAR WINDOW DEFOGGER SWITCH -
OPERATION..........................8G-8
REAR WINDOW DEFOGGER SYSTEM -
DIAGNOSIS AND TESTING..............8G-4
REAR WIPER & WASHER SYSTEM -
CLEANING..........................8R-32
REAR WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING.............8R-30
REAR WIPER & WASHER SYSTEM -
INSPECTION........................8R-33
REAR WIPER ARM - DESCRIPTION......8R-37
REAR WIPER ARM - INSTALLATION......8R-38
REAR WIPER ARM - OPERATION........8R-38
REAR WIPER ARM - REMOVAL.........8R-38
REAR WIPER BLADE - DESCRIPTION
.....8R-39
REAR WIPER BLADE - INSTALLATION
....8R-40
REAR WIPER BLADE - OPERATION
......8R-39
REAR WIPER BLADE - REMOVAL
........8R-40
REAR WIPER MOTOR - DESCRIPTION
....8R-41
REAR WIPER MOTOR - INSTALLATION
. . . 8R-42
REAR WIPER MOTOR - OPERATION
......8R-41
REAR WIPER MOTOR - REMOVAL
.......8R-42
REAR WIPERS/WASHERS -
DESCRIPTION
.......................8R-27
REAR WIPERS/WASHERS - OPERATION
. . 8R-29
REAR WIPER/WASHER SWITCH -
DESCRIPTION
.......................8R-43
REAR WIPER/WASHER SWITCH -
OPERATION
.........................8R-43
REARVIEW MIRROR SUPPORT BRACKET
- INSTALLATION
....................23-161RECEIVER LAMP BULB - INSTALLATION,
ASH ...............................8L-71
RECEIVER LAMP BULB - REMOVAL, ASH . . 8L-71
RECEIVER LAMP UNIT - INSTALLATION,
ASH ...............................8L-72
RECEIVER LAMP UNIT - REMOVAL, ASH . . 8L-72
RECIRC DOOR - INSTALLATION.........24-37
RECIRC DOOR - REMOVAL.............24-37
RECIRCULATION DOOR ACTUATOR -
INSTALLATION.......................24-26
RECIRCULATION DOOR ACTUATOR -
REMOVAL..........................24-26
RECLINER - FRONT - INSTALLATION,
SEAT BACK........................23-166
RECLINER - FRONT - REMOVAL, SEAT
BACK.............................23-166
RECOMMENDATIONS - STANDARD
PROCEDURE, HOISTING.................0-4
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT.......................24-41
RECOVERY PRESS CONTAINER -
DESCRIPTION, COOLANT...............7-19
RECOVERY PRESS CONTAINER -
OPERATION, COOLANT.................7-19
REFACING - STANDARD PROCEDURE . . 9-26,9-34
REFERENCES - DESCRIPTION, TORQUE . . Intro.-7
REFILLING COOLING SYSTEM 3.7L
ENGINE - STANDARD PROCEDURE........7-12
REFRIGERANT - DESCRIPTION..........24-53
REFRIGERANT - OPERATION............24-53
REFRIGERANT HOSES/LINES/TUBES
PRECAUTIONS - CAUTION.............24-40
REFRIGERANT LINE - DESCRIPTION......24-38
REFRIGERANT OIL - DESCRIPTION......24-53
REFRIGERANT OIL - OPERATION........24-54
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-54
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-41
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-41
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-41
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-40
REFRIGERANT SYSTEM SERVICE PORT -
DESCRIPTION........................24-2
REFRIGERANT SYSTEM SERVICE PORT -
OPERATION..........................24-2
REGULATOR - DESCRIPTION, FUEL
PRESSURE.........................14-13
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-31
REGULATOR - ELECTRIC -
INSTALLATION, WINDOW.......23-126,23-134
REGULATOR - ELECTRIC - REMOVAL,
WINDOW....................23-126,23-134
REGULATOR - INSTALLATION, FUEL
PRESSURE.........................14-14
REGULATOR - MANUAL - INSTALLATION,
WINDOW....................23-126,23-133
REGULATOR - MANUAL - REMOVAL,
WINDOW....................23-126,23-133
REGULATOR - OPERATION, FUEL
PRESSURE.........................14-14
REGULATOR - OPERATION, VOLTAGE.....8F-31
REGULATOR - REMOVAL, FUEL
PRESSURE.........................14-14
REINFORCEMENT - INSTALLATION,
GRILLE OPENING...................23-142
REINFORCEMENT - REMOVAL, GRILLE
OPENING..........................23-142
RELAY - DESCRIPTION.............8W-97-13
RELAY - DESCRIPTION, A/C
COMPRESSOR CLUTCH...............24-15
RELAY - DESCRIPTION, AMPLIFIER
CHOKE..............................8A-3
RELAY - DESCRIPTION, BLOWER
MOTOR............................24-20
RELAY - DESCRIPTION, CLUTCH SWITCH
OVERRIDE...........................6-10
RELAY - DESCRIPTION, DAYTIME
RUNNING LAMP
.....................8L-20
RELAY - DESCRIPTION, DOOR LOCK
......8N-6
RELAY - DESCRIPTION, FRONT FOG
LAMP
..............................8L-22
RELAY - DESCRIPTION, FUEL PUMP
.....14-34
RELAY - DESCRIPTION, HEADLAMP
HIGH BEAM
.........................8L-33RELAY - DESCRIPTION, HEADLAMP LOW
BEAM..............................8L-39
RELAY - DESCRIPTION, PARK LAMP.....8L-54
RELAY - DESCRIPTION, REAR FOG LAMP . 8L-56
RELAY - DESCRIPTION, REAR WINDOW
DEFOGGER..........................8G-6
RELAY - DESCRIPTION, STARTER
MOTOR............................8F-41
RELAY - DESCRIPTION, TRAILER TOW....8L-61
RELAY - DESCRIPTION, TRANSMISSION
CONTROL.........................21-168
RELAY - DESCRIPTION, WIPER
HIGH/LOW..........................8R-23
RELAY - DESCRIPTION, WIPER ON/OFF . . . 8R-25
RELAY - DIAGNOSIS AND TESTING . . . 8W-97-13
RELAY - DIAGNOSIS AND TESTING,
AMPLIFIER CHOKE....................8A-4
RELAY - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-21
RELAY - DIAGNOSIS AND TESTING,
COMPRESSOR CLUTCH...............24-15
RELAY - DIAGNOSIS AND TESTING,
DOOR LOCK.........................8N-6
RELAY - DIAGNOSIS AND TESTING,
FRONT FOG LAMP....................8L-23
RELAY - DIAGNOSIS AND TESTING,
FUEL PUMP.........................14-34
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP HIGH BEAM...............8L-34
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP LOW BEAM...............8L-40
RELAY - DIAGNOSIS AND TESTING,
HORN..............................8H-3
RELAY - DIAGNOSIS AND TESTING,
PARK LAMP.........................8L-55
RELAY - DIAGNOSIS AND TESTING,
REAR FOG LAMP.....................8L-57
RELAY - DIAGNOSIS AND TESTING,
REAR WINDOW DEFOGGER.............8G-6
RELAY - DIAGNOSIS AND TESTING,
STARTER ...........................8F-42
RELAY - DIAGNOSIS AND TESTING,
TRAILER TOW.......................8L-62
RELAY - DIAGNOSIS AND TESTING,
WIPER HIGH/LOW...................8R-24
RELAY - DIAGNOSIS AND TESTING,
WIPER ON/OFF......................8R-26
RELAY - INSTALLATION............8W-97-14
RELAY - INSTALLATION, A/C
COMPRESSOR CLUTCH...............24-16
RELAY - INSTALLATION, AMPLIFIER
CHOKE..............................8A-4
RELAY - INSTALLATION, BLOWER
MOTOR............................24-22
RELAY - INSTALLATION, CLUTCH
SWITCH OVERRIDE....................6-10
RELAY - INSTALLATION, DAYTIME
RUNNING LAMP.....................8L-21
RELAY - INSTALLATION, DOOR LOCK.....8N-7
RELAY - INSTALLATION, FRONT FOG
LAMP..............................8L-24
RELAY - INSTALLATION, FUEL PUMP.....14-34
RELAY - INSTALLATION, HEADLAMP
HIGH BEAM.........................8L-35
RELAY - INSTALLATION, HEADLAMP
LOW BEAM.........................8L-41
RELAY - INSTALLATION, HORN..........8H-3
RELAY - INSTALLATION, PARK LAMP.....8L-56
RELAY - INSTALLATION, REAR FOG
LAMP..............................8L-58
RELAY - INSTALLATION, REAR WINDOW
DEFOGGER..........................8G-7
RELAY - INSTALLATION, STARTER
MOTOR............................8F-43
RELAY - INSTALLATION, TRAILER TOW . . . 8L-64
RELAY - INSTALLATION, WIPER
HIGH/LOW..........................8R-24
RELAY - INSTALLATION, WIPER ON/OFF . . 8R-26
RELAY - OPERATION...............8W-97-13
RELAY - OPERATION, A/C COMPRESSOR
CLUTCH............................24-15
RELAY - OPERATION, AMPLIFIER CHOKE
. . . 8A-3
RELAY - OPERATION, BLOWER MOTOR
. . . 24-20
RELAY - OPERATION, CLUTCH SWITCH
OVERRIDE
...........................6-10
RELAY - OPERATION, DAYTIME
RUNNING LAMP
.....................8L-20
RELAY - OPERATION, DOOR LOCK
........8N-6
KJINDEX 21
Description Group-Page Description Group-Page Description Group-Page

SEAL - INSTALLATION, REAR OUTPUT
SHAFT............................21-212
SEAL - NV1500 - INSTALLATION,
EXTENSION HOUSING.................21-32
SEAL - NV1500 - REMOVAL, EXTENSION
HOUSING...........................21-32
SEAL - NV3550 - INSTALLATION,
EXTENSION HOUSING.................21-74
SEAL - NV3550 - REMOVAL, EXTENSION
HOUSING...........................21-74
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL.....................9-48
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ................................9-48
SEAL - REMOVAL, ADAPTER HOUSING . . 21-124
SEAL - REMOVAL, A-PILLAR...........23-185
SEAL - REMOVAL, COWL/PLENUM......23-187
SEAL - REMOVAL, COWL/PLENUM
WINDOW BAFFLE...................23-187
SEAL - REMOVAL, FRONT OUTPUT
SHAFT......................21-208,21-246
SEAL - REMOVAL, GLASS PANEL.......23-178
SEAL - REMOVAL, OIL PUMP FRONT....21-152
SEAL - REMOVAL, PINION.....3-102,3-38,3-68
SEAL - REMOVAL, REAR OUTPUT SHAFT . 21-210
SEAL AREA LEAKS - DIAGNOSIS AND
TESTING, REAR.......................9-61
SEALER LOCATIONS - SPECIFICATIONS . . . 23-87
SEALS - DESCRIPTION, VALVE GUIDE . 9-29,9-38
SEALS - INSTALLATION, AXLE SHAFT....3-102,
3-38
SEALS - REMOVAL, AXLE SHAFT....3-101,3-37
SEAT - FRONT - INSTALLATION........23-165
SEAT - FRONT - REMOVAL............23-165
SEAT - REAR - INSTALLATION.........23-168
SEAT - REAR - REMOVAL.............23-168
SEAT BACK - FRONT - INSTALLATION . . . 23-166
SEAT BACK - FRONT - REMOVAL.......23-166
SEAT BACK - REAR - INSTALLATION....23-168
SEAT BACK - REAR - REMOVAL........23-168
SEAT BACK COVER - FRONT -
INSTALLATION......................23-167
SEAT BACK COVER - FRONT - REMOVAL . 23-166
SEAT BACK COVER - REAR -
INSTALLATION......................23-169
SEAT BACK COVER - REAR - REMOVAL . . 23-169
SEAT BACK CUSHION - FRONT -
INSTALLATION......................23-167
SEAT BACK CUSHION - FRONT -
REMOVAL.........................23-167
SEAT BACK CUSHION - REAR -
INSTALLATION......................23-170
SEAT BACK CUSHION - REAR -
REMOVAL.........................23-170
SEAT BACK FRAME - REAR -
INSTALLATION......................23-171
SEAT BACK FRAME - REAR - REMOVAL . . 23-171
SEAT BACK LATCH / LOCK -
INSTALLATION, FOLDING REAR........23-170
SEAT BACK LATCH / LOCK - REMOVAL,
FOLDING REAR.....................23-170
SEAT BACK LATCH STRIKER -
INSTALLATION, REAR................23-171
SEAT BACK LATCH STRIKER - REMOVAL,
REAR.............................23-170
SEAT BACK RECLINER - FRONT -
INSTALLATION......................23-166
SEAT BACK RECLINER - FRONT -
REMOVAL.........................23-166
SEAT BELT & RETRACTOR -
INSTALLATION, FRONT................8O-24
SEAT BELT & RETRACTOR -
INSTALLATION, REAR CENTER..........8O-33
SEAT BELT & RETRACTOR -
INSTALLATION, REAR OUTBOARD.......8O-34
SEAT BELT & RETRACTOR - REMOVAL,
FRONT.............................8O-23
SEAT BELT & RETRACTOR - REMOVAL,
REAR CENTER.......................8O-32
SEAT BELT & RETRACTOR - REMOVAL,
REAR OUTBOARD....................8O-33
SEAT BELT BUCKLE - INSTALLATION,
FRONT
.............................8O-26
SEAT BELT BUCKLE - INSTALLATION,
REAR
..............................8O-35
SEAT BELT BUCKLE - REMOVAL, FRONT
. . 8O-25
SEAT BELT BUCKLE - REMOVAL, REAR
. . . 8O-34
SEAT BELT SWITCH - DESCRIPTION
.....8O-35SEAT BELT SWITCH - OPERATION.......8O-36
SEAT BELT TENSIONER - DESCRIPTION . . . 8O-36
SEAT BELT TENSIONER - OPERATION....8O-36
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-38
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-37
SEAT CUSHION - FRONT -
INSTALLATION......................23-167
SEAT CUSHION - FRONT - REMOVAL....23-167
SEAT CUSHION - REAR - INSTALLATION . 23-171
SEAT CUSHION - REAR - REMOVAL.....23-171
SEAT CUSHION COVER - FRONT -
INSTALLATION......................23-167
SEAT CUSHION COVER - FRONT -
REMOVAL.........................23-167
SEAT CUSHION SIDE SHIELDS -
INSTALLATION......................23-167
SEAT CUSHION SIDE SHIELDS -
REMOVAL.........................23-167
SEAT ELEMENT - DESCRIPTION, HEATED . 8G-13
SEAT ELEMENT - DIAGNOSIS AND
TESTING, HEATED....................8G-13
SEAT ELEMENT - OPERATION, HEATED . . . 8G-13
SEAT HEATER SWITCH - DESCRIPTION,
DRIVER............................8G-11
SEAT HEATER SWITCH - DESCRIPTION,
PASSENGER........................8G-14
SEAT HEATER SWITCH - INSTALLATION,
DRIVER............................8G-13
SEAT HEATER SWITCH - INSTALLATION,
PASSENGER........................8G-15
SEAT HEATER SWITCH - OPERATION,
DRIVER............................8G-12
SEAT HEATER SWITCH - OPERATION,
PASSENGER........................8G-14
SEAT HEATER SWITCH - REMOVAL,
DRIVER............................8G-13
SEAT HEATER SWITCH - REMOVAL,
PASSENGER........................8G-15
SEAT MODULE - DESCRIPTION, HEATED . . 8E-21
SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED....................8E-22
SEAT MODULE - INSTALLATION, HEATED . . 8E-24
SEAT MODULE - OPERATION, HEATED....8E-21
SEAT MODULE - REMOVAL, HEATED.....8E-24
SEAT RISER - INSTALLATION, MANUAL . . 23-168
SEAT RISER - REMOVAL, MANUAL......23-167
SEAT SENSOR - DIAGNOSIS AND
TESTING, HEATED....................8G-14
SEAT SWITCH - DESCRIPTION, LEFT
POWER............................8N-16
SEAT SWITCH - DESCRIPTION, RIGHT
POWER............................8N-19
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED..............8G-12,8G-14
SEAT SWITCH - DIAGNOSIS AND
TESTING, LEFT POWER...............8N-17
SEAT SWITCH - DIAGNOSIS AND
TESTING, RIGHT POWER..............8N-19
SEAT SWITCH - INSTALLATION, LEFT
POWER............................8N-18
SEAT SWITCH - INSTALLATION, RIGHT
POWER............................8N-20
SEAT SWITCH - OPERATION, LEFT
POWER............................8N-17
SEAT SWITCH - OPERATION, RIGHT
POWER............................8N-19
SEAT SWITCH - REMOVAL, LEFT POWER . 8N-18
SEAT SWITCH - REMOVAL, RIGHT
POWER............................8N-20
SEAT SYSTEM - DESCRIPTION, HEATED . . 8G-10
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED
....................8G-11
SEAT SYSTEM - OPERATION, HEATED
....8G-10
SEAT TRACK - DESCRIPTION
...........8N-15
SEAT TRACK - DIAGNOSIS AND TESTING
. 8N-16
SEAT TRACK - INSTALLATION
..........23-168
SEAT TRACK - INSTALLATION
..........8N-16
SEAT TRACK - OPERATION
.............8N-15
SEAT TRACK - REMOVAL
.............23-168
SEAT TRACK - REMOVAL
..............8N-16
SEATBELT INDICATOR - DESCRIPTION
....8J-27
SEATBELT INDICATOR - OPERATION
......8J-28
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES
.....................9-26
SEATS - DESCRIPTION, POWER
.........8N-14SEATS - DIAGNOSIS AND TESTING,
POWER............................8N-15
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES.................9-28,9-36
SEATS - OPERATION, POWER..........8N-15
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .........................9-27,9-35
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT . . 8Q-3
SECURITY INDICATOR - DESCRIPTION....8J-28
SECURITY INDICATOR - OPERATION.....8J-28
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT..............8Q-6
SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL LEVEL.................14-9
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL.............14-9
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL............14-10
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL..........................14-9
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-9
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-13
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-15
SENSE - PCM INPUT - OPERATION, ASD . . . 8I-4
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - DESCRIPTION, AMBIENT
TEMP..............................8M-9
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-24
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-30
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-19
SENSOR - DESCRIPTION, FRONT
IMPACT............................8O-21
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - DESCRIPTION, INPUT SPEED . 21-143
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - DESCRIPTION, KNOCK........8I-11
SENSOR - DESCRIPTION, LINE
PRESSURE (LP)....................21-144
SENSOR - DESCRIPTION, MAP..........14-38
SENSOR - DESCRIPTION, OUTPUT
SPEED............................21-152
SENSOR - DESCRIPTION, OXYGEN.......14-40
SENSOR - DESCRIPTION, POSITION....21-209,
21-247
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-47
SENSOR - DESCRIPTION,
TRANSMISSION RANGE..............21-168
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE........21-170
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE...............8M-9
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-14
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-24
SENSOR - INSTALLATION, CRANKSHAFT
POSITION..........................14-32
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - INSTALLATION, FRONT
IMPACT............................8O-22
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-34
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT......................14-10
SENSOR - INSTALLATION, INPUT SPEED . 21-143
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE
......................14-38
SENSOR - INSTALLATION, KNOCK
........8I-12
SENSOR - INSTALLATION, LINE
PRESSURE (LP)
....................21-144
SENSOR - INSTALLATION, MAP
.........14-40
SENSOR - INSTALLATION, OUTPUT
SPEED
............................21-152
KJINDEX 23
Description Group-Page Description Group-Page Description Group-Page

SENSOR - INSTALLATION, OXYGEN......14-43
SENSOR - INSTALLATION, POSITION....21-210,
21-247
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-35
SENSOR - INSTALLATION, THROTTLE
POSITION..........................14-48
SENSOR - OPERATION, AMBIENT TEMP . . . 8M-9
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-24
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-31
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE...............7-20
SENSOR - OPERATION, FRONT IMPACT . . . 8O-21
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - OPERATION, INPUT SPEED . . . 21-143
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - OPERATION, KNOCK..........8I-11
SENSOR - OPERATION, LINE PRESSURE
(LP)..............................21-144
SENSOR - OPERATION, MAP...........14-38
SENSOR - OPERATION, OUTPUT SPEED . . 21-152
SENSOR - OPERATION, OXYGEN........14-40
SENSOR - OPERATION, POSITION......21-209,
21-247
SENSOR - OPERATION, THROTTLE
POSITION..........................14-47
SENSOR - OPERATION, TRANSMISSION
RANGE............................21-168
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE.....................21-170
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-24
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-31
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-20
SENSOR - REMOVAL, FRONT IMPACT....8O-22
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-34
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - REMOVAL, INPUT SPEED.....21-143
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE......................14-37
SENSOR - REMOVAL, KNOCK...........8I-12
SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-144
SENSOR - REMOVAL, MAP.............14-39
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-152
SENSOR - REMOVAL, OXYGEN..........14-41
SENSOR - REMOVAL, POSITION . . 21-210,21-247
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-35
SENSOR - REMOVAL, THROTTLE
POSITION..........................14-47
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE.......8M-9
SENSOR RETURN - DESCRIPTION.......8E-14
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-65
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE
..........................9-65
SENSOR/SWITCH - OPERATION, OIL
PRESSURE
..........................9-65
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE
..........................9-65
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION
.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION
.......................8E-18
SENTRY KEY IMMOBILIZER MODULE -
OPERATION
.........................8E-16
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL
..........................8E-17
SENTRY KEY TRANSPONDER
PROGRAMMING - STANDARD
PROCEDURE
.........................8Q-8
SERPENTINE DRIVE BELT - DIAGNOSIS
AND TESTING
........................7-15
SERVO - DESCRIPTION
.................8P-4
SERVO - INSTALLATION
................8P-5
SERVO - OPERATION
..................8P-4
SERVO - REMOVAL
....................8P-4SETTING TRANSMITTER CODES -
STANDARD PROCEDURE...............8M-9
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-9
SHAFT - CAUTION, HALF................3-10
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-10
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - FRONT - INSTALLATION,
PROPELLER...........................3-6
SHAFT - FRONT - REMOVAL,
PROPELLER...........................3-6
SHAFT - INSTALLATION, BALANCE........9-74
SHAFT - INSTALLATION, HALF...........3-11
SHAFT - INSTALLATION, IDLER..........9-77
SHAFT - INSTALLATION, INTERMEDIATE . . 19-11
SHAFT - REAR - INSTALLATION,
PROPELLER...........................3-7
SHAFT - REAR - REMOVAL, PROPELLER....3-7
SHAFT - REMOVAL, BALANCE...........9-74
SHAFT - REMOVAL, HALF...............3-10
SHAFT - REMOVAL, IDLER..............9-77
SHAFT - REMOVAL, INTERMEDIATE......19-11
SHAFT ANGLE - STANDARD
PROCEDURES, PROPELLER..............3-3
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT.....................21-208,21-246
SHAFT SEAL - INSTALLATION, REAR
OUTPUT............................21-212
SHAFT SEAL - REMOVAL, FRONT
OUTPUT.....................21-208,21-246
SHAFT SEAL - REMOVAL, REAR OUTPUT . 21-210
SHAFT SEALS - INSTALLATION, AXLE....3-102,
3-38
SHAFT SEALS - REMOVAL, AXLE....3-101,3-37
SHAFT, SPECIFICATIONS - HALF..........3-11
SHAFT, SPECIFICATIONS - PROPELLER.....3-6
SHAFTS - INSTALLATION, AXLE . 3-101,3-37,3-65
SHAFTS - REMOVAL, AXLE.....3-101,3-37,3-65
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH...............23-143
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH...............23-144
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH...............23-143
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH...............23-144
SHIELDS - DESCRIPTION, HEAT..........11-4
SHIELDS - INSTALLATION, SEAT
CUSHION SIDE.....................23-167
SHIELDS - REMOVAL, SEAT CUSHION
SIDE.............................23-167
SHIFT BEZEL - INSTALLATION.........23-158
SHIFT BEZEL - REMOVAL.............23-158
SHIFT BOOT - INSTALLATION, 4WD
FLOOR............................23-156
SHIFT BOOT - REMOVAL, 4WD FLOOR . . . 23-156
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-124
SHIFT INTERLOCK SYSTEM - DIAGNOSIS
AND TESTING, BRAKE TRANSMISSION . . 21-125
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-125
SHIFT LEVER - INSTALLATION . . . 21-214,21-249
SHIFT LEVER - REMOVAL.......21-213,21-248
SHIFT MECHANISM - DESCRIPTION.....21-160
SHIFT MECHANISM - INSTALLATION....21-160
SHIFT MECHANISM - OPERATION
......21-160
SHIFT MECHANISM - REMOVAL
........21-160
SHOCK - INSTALLATION
................2-18
SHOCK - REMOVAL
....................2-18
SHOES - INSTALLATION, DRUM BRAKE
....5-11
SHOES - REMOVAL, DRUM BRAKE
.......5-11
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
...........................8W-01-9
SIDE - INSTALLATION, LEFT
.........2-12,2-15
SIDE - INSTALLATION, RIGHT
........2-12,2-15
SIDE - REMOVAL, LEFT
.............2-11,2-15
SIDE - REMOVAL, RIGHT
...........2-11,2-14
SIDE BEZEL - INSTALLATION,
INSTRUMENT PANEL PASSENGER
......23-154SIDE BEZEL - REMOVAL, INSTRUMENT
PANEL PASSENGER..................23-154
SIDE BEZELS - INSTALLATION,
INSTRUMENT PANEL DRIVER..........23-154
SIDE BEZELS - REMOVAL, INSTRUMENT
PANEL DRIVER.....................23-153
SIDE CURTAIN AIRBAG - DESCRIPTION . . . 8O-38
SIDE CURTAIN AIRBAG - INSTALLATION . . 8O-41
SIDE CURTAIN AIRBAG - OPERATION....8O-39
SIDE CURTAIN AIRBAG - REMOVAL......8O-40
SIDE IMPACT AIRBAG CONTROL
MODULE - DESCRIPTION..............8O-43
SIDE IMPACT AIRBAG CONTROL
MODULE - INSTALLATION.............8O-45
SIDE IMPACT AIRBAG CONTROL
MODULE - OPERATION................8O-43
SIDE IMPACT AIRBAG CONTROL
MODULE - REMOVAL.................8O-44
SIDE MOLDINGS - INSTALLATION, BODY . 23-140
SIDE MOLDINGS - REMOVAL, BODY....23-140
SIDE RAIL WEATHERSTRIP/RETAINER -
INSTALLATION......................23-186
SIDE RAIL WEATHERSTRIP/RETAINER -
REMOVAL.........................23-186
SIDE SHIELDS - INSTALLATION, SEAT
CUSHION..........................23-167
SIDE SHIELDS - REMOVAL, SEAT
CUSHION..........................23-167
SIDE VIEW MIRROR - INSTALLATION....23-145
SIDE VIEW MIRROR - REMOVAL.......23-145
SIDEVIEW MIRROR - REMOVAL..........8N-13
SIGNAL INDICATOR - DESCRIPTION,
TURN..............................8J-34
SIGNAL INDICATOR - OPERATION, TURN . . 8J-34
SILL SCUFF PLATE - INSTALLATION,
DOOR............................23-157
SILL SCUFF PLATE - REMOVAL, DOOR . . . 23-157
SINGLE CARDAN UNIVERSAL JOINTS -
ASSEMBLY...........................3-9
SINGLE CARDAN UNIVERSAL JOINTS -
DISASSEMBLY.........................3-8
SIREN - DESCRIPTION................8Q-16
SIREN - INSTALLATION...............8Q-17
SIREN - OPERATION..................8Q-17
SIREN - REMOVAL...................8Q-17
SKID PLATE - INSTALLATION, FRONT......13-6
SKID PLATE - INSTALLATION, FUEL
TANK ...............................13-9
SKID PLATE - INSTALLATION, TRANSFER
CASE...............................13-7
SKID PLATE - REMOVAL, FRONT.........13-6
SKID PLATE - REMOVAL, FUEL TANK......13-9
SKID PLATE - REMOVAL, TRANSFER
CASE...............................13-7
SKIS INDICATOR - DESCRIPTION........8J-31
SKIS INDICATOR - OPERATION..........8J-31
SKIS INITIALIZATION - STANDARD
PROCEDURE.........................8Q-8
SLEEVE - INSTALLATION, HEADREST....23-164
SLEEVE - REMOVAL, HEADREST.......23-164
SOLENOID - DESCRIPTION, EVAP/PURGE . 25-27
SOLENOID - INSTALLATION, EVAP/
PURGE.............................25-27
SOLENOID - OPERATION, EVAP/PURGE . . . 25-27
SOLENOID - REMOVAL, EVAP/PURGE.....25-27
SOLENOID SWITCH VALVE -
DESCRIPTION......................21-161
SOLENOID SWITCH VALVE - OPERATION . 21-161
SOLENOIDS - DESCRIPTION...........21-161
SOLENOIDS - OPERATION.............21-162
SOLENOID/TRS ASSEMBLY -
DESCRIPTION, TRANSMISSION........21-169
SOLENOID/TRS ASSEMBLY -
INSTALLATION, TRANSMISSION........21-170
SOLENOID/TRS ASSEMBLY -
OPERATION, TRANSMISSION..........21-169
SOLENOID/TRS ASSEMBLY - REMOVAL,
TRANSMISSION.....................21-170
SPACER - INSTALLATION, COLLAPSIBLE . . . 3-70
SPACER - REMOVAL, COLLAPSIBLE.......3-70
SPARE TIRE - INSTALLATION............22-9
SPARE TIRE - REMOVAL
................22-8
SPARE TIRE &TEMPORARY -
DESCRIPTION
........................22-6
SPARK PLUG - CLEANING SPARK
PLUGS
.............................8I-15
SPARK PLUG - DESCRIPTION
...........8I-12
SPARK PLUG - INSTALLATION
...........8I-15
24 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

ADJUSTER (TAPPET) NOISE DIAGNOSIS
- DIAGNOSIS AND TESTING, LASH........9-28
ADJUSTMENT, FRONT FOG LAMP UNIT . . . 8L-25
ADJUSTMENT, HEADLAMP UNIT.........8L-42
AIMING - STANDARD PROCEDURE,
LAMP BAR..........................8L-65
ARM BUSHING - INSTALLATION, LOWER
CONTROL............................2-3
ARM BUSHING - INSTALLATION, LOWER
SUSPENSION..........................2-8
ARM BUSHING - INSTALLATION, UPPER
SUSPENSION..........................2-8
ARM BUSHING - REMOVAL, LOWER
CONTROL............................2-2
ARM BUSHING - REMOVAL, LOWER
SUSPENSION..........................2-7
ARM BUSHING - REMOVAL, UPPER
SUSPENSION..........................2-7
ARM BUSHINGS - INSTALLATION,
UPPER CONTROL......................2-4
ARM BUSHINGS - REMOVAL, UPPER
CONTROL............................2-3
ARMS - INSPECTION, ROCKER...........9-30
ARMS - INSTALLATION, ROCKER.........9-30
ARMS - REMOVAL, ROCKER.............9-29
ASSEMBLY - INSTALLATION, ENGINE......9-12
ASSEMBLY - REMOVAL, ENGINE.........9-12
ASSEMBLY, OIL PUMP.................9-50
BACKUP LAMP SWITCH - DESCRIPTION . . 8L-15
BACKUP LAMP SWITCH - DIAGNOSIS
AND TESTING.........................8L-15
BACKUP LAMP SWITCH - OPERATION....8L-15
BALANCE SHAFT - DESCRIPTION.........9-59
BALANCE SHAFT - OPERATION...........9-59
BALANCE SHAFT - REMOVAL............9-60
BALANCE SHAFT CARRIER -
INSTALLATION........................9-64
BALANCE SHAFT CARRIER - REMOVAL....9-64
BALANCE SHAFT CHAIN - INSTALLATION . . . 9-64
BALANCE SHAFT CHAIN - REMOVAL......9-64
BALANCE SHAFT TIMING, INSTALLATION . . . 9-61
BALL JOINT - INSTALLATION, LOWER......2-5
BALL JOINT - INSTALLATION, UPPER......2-6
BALL JOINT - REMOVAL, LOWER..........2-5
BALL JOINT - REMOVAL, UPPER..........2-6
BAR - DESCRIPTION, LAMP............8L-65
BAR - DIAGNOSIS AND TESTING, LAMP . . 8L-65
BAR - INSTALLATION, LAMP............8L-66
BAR - OPERATION, LAMP..............8L-65
BAR - REMOVAL, LAMP...............8L-65
BAR AIMING - STANDARD PROCEDURE,
LAMP..............................8L-65
BAR SWITCH - DESCRIPTION, LAMP.....8L-67
BAR SWITCH - INSTALLATION, LAMP....8L-67
BAR SWITCH - REMOVAL, LAMP........8L-67
BEAM RELAY - DESCRIPTION,
HEADLAMP HIGH....................8L-33
BEAM RELAY - DESCRIPTION,
HEADLAMP LOW.....................8L-39
BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP HIGH............8L-34
BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP LOW.............8L-40
BEAM RELAY - INSTALLATION,
HEADLAMP HIGH
....................8L-35
BEAM RELAY - INSTALLATION,
HEADLAMP LOW
.....................8L-41
BEAM RELAY - OPERATION, HEADLAMP
HIGH
..............................8L-33
BEAM RELAY - OPERATION, HEADLAMP
LOW
..............................8L-39
BEAM RELAY - REMOVAL, HEADLAMP
HIGH
..............................8L-34
BEAM RELAY - REMOVAL, HEADLAMP
LOW
..............................8L-40
BEARING - FITTING - STANDARD
PROCEDURE, MAIN
....................9-35
BEARING CLEARANCE USING
PLASTIGAGE - STANDARD
PROCEDURE, MEASURING
..............9-11
BELT - INSTALLATION, TIMING
...........9-56
BELT - REMOVAL, TIMING
..............9-55
BELT COVER(S) - INSTALLATION,
TIMING
.............................9-53
BELT COVER(S) - REMOVAL, TIMING
......9-53
BELT DIAGNOSIS - DIAGNOSIS AND
TESTING, SERPENTINE DRIVE
...........7-15BELT TENSIONER & PULLEY -
INSTALLATION, TIMING.................9-59
BELT TENSIONER & PULLEY -
REMOVAL, TIMING....................9-59
BLOCK - DESCRIPTION, ENGINE..........9-30
BLOCK HEATER - 2.4L - DESCRIPTION,
ENGINE.............................7-20
BLOCK HEATER - 2.4L - OPERATION,
ENGINE.............................7-20
BORE FITTING - STANDARD
PROCEDURE, PISTON TO CYLINDER......9-30
BORE HONING - STANDARD
PROCEDURE, CYLINDER................9-31
BRACKET BUSHING - INSTALLATION,
CLEVIS..............................2-4
BRACKET BUSHING - REMOVAL, CLEVIS....2-2
BRAKE LAMP SWITCH - DESCRIPTION . . . 8L-16
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-17
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-18
BRAKE LAMP SWITCH - OPERATION.....8L-16
BRAKE LAMP SWITCH - REMOVAL......8L-17
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP................8L-19
BULB - INSTALLATION, FRONT FOG
LAMP..............................8L-22
BULB - INSTALLATION, FRONT LAMP....8L-27
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-28
BULB - INSTALLATION, HEADLAMP......8L-32
BULB - INSTALLATION, LICENSE PLATE
LAMP..............................8L-45
BULB - INSTALLATION, REAR LAMP.....8L-59
BULB - INSTALLATION, REPEATER LAMP . . 8L-60
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-18
BULB - REMOVAL, FRONT FOG LAMP....8L-21
BULB - REMOVAL, FRONT LAMP........8L-27
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-28
BULB - REMOVAL, HEADLAMP..........8L-30
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-44
BULB - REMOVAL, REAR LAMP.........8L-59
BULB - REMOVAL, REPEATER LAMP.....8L-60
BUSHING - INSTALLATION, CLEVIS
BRACKET.............................2-4
BUSHING - INSTALLATION, LOWER
CONTROL ARM........................2-3
BUSHING - INSTALLATION, LOWER
SUSPENSION ARM.....................2-8
BUSHING - INSTALLATION, UPPER
SUSPENSION ARM.....................2-8
BUSHING - REMOVAL, CLEVIS BRACKET....2-2
BUSHING - REMOVAL, LOWER CONTROL
ARM ................................2-2
BUSHING - REMOVAL, LOWER
SUSPENSION ARM.....................2-7
BUSHING - REMOVAL, UPPER
SUSPENSION ARM.....................2-7
BUSHINGS - INSTALLATION, UPPER
CONTROL ARM........................2-4
BUSHINGS - REMOVAL, UPPER
CONTROL ARM........................2-3
CAMSHAFT END-PLAY - STANDARD
PROCEDURE.........................9-23
CAMSHAFT OIL SEAL(S) - INSTALLATION . . 9-22
CAMSHAFT OIL SEAL(S) - REMOVAL......9-22
CAMSHAFT(S) - CLEANING..............9-24
CAMSHAFT(S) - DESCRIPTION...........9-23
CAMSHAFT(S) - INSPECTION............9-25
CAMSHAFT(S) - INSTALLATION..........9-25
CAMSHAFT(S) - OPERATION.............9-23
CAMSHAFT(S) - REMOVAL..............9-24
CAP - CLEANING, RADIATOR PRESSURE . . . 7-25
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-25
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-25
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-25
CAP - OPERATION, RADIATOR
PRESSURE
..........................7-25
CARRIER - INSTALLATION, BALANCE
SHAFT
..............................9-64
CARRIER - REMOVAL, BALANCE SHAFT
....9-64
CATALYTIC CONVERTER - DESCRIPTION
. . . 11-2
CATALYTIC CONVERTER - INSPECTION
....11-3CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-2
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION................8L-19
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL....................8L-18
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION.................8L-19
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL....................8L-19
CHAIN - INSTALLATION, BALANCE
SHAFT..............................9-64
CHAIN - REMOVAL, BALANCE SHAFT......9-64
CHANGE - STANDARD PROCEDURE,
ENGINE OIL AND FILTER................9-47
CHART - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIAGNOSIS............7-5
CHECK, STANDARD PROCEDURE -
ENGINE OIL LEVEL....................9-47
CHECKING - DIAGNOSIS AND TESTING,
ENGINE OIL PRESSURE................9-46
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-2
CLAMPS - DESCRIPTION, HOSE...........7-1
CLAMPS - OPERATION, HOSE.............7-2
CLEANING, CAMSHAFT(S)...............9-24
CLEANING, CYLINDER HEAD.............9-20
CLEANING, CYLINDER HEAD COVER......9-26
CLEANING, EXHAUST MANIFOLD.........9-53
CLEANING, INTAKE/EXHAUST VALVES &
SEATS................................9-27
CLEANING, OIL PUMP..................9-49
CLEANING, RADIATOR.................7-24
CLEANING, RADIATOR PRESSURE CAP....7-25
CLEANING, REMOVAL..................9-55
CLEANING, STANDARD PROCEDURE......9-31
CLEARANCE USING PLASTIGAGE -
STANDARD PROCEDURE, MEASURING
BEARING............................9-11
CLEVIS BRACKET BUSHING -
INSTALLATION.........................2-4
CLEVIS BRACKET BUSHING - REMOVAL....2-2
COLLAR - INSTALLATION, STRUCTURAL . . . 9-44
COLLAR - REMOVAL, STRUCTURAL.......9-44
COMBINATION FLASHER - DESCRIPTION . . 8L-19
COMBINATION FLASHER - OPERATION . . . 8L-19
COMBUSTION PRESSURE LEAKAGE
TEST - DIAGNOSIS AND TESTING,
CYLINDER............................9-3
COMPRESSION PRESSURE TEST -
DIAGNOSIS AND TESTING, CYLINDER......9-3
CONNECTING ROD - DESCRIPTION,
PISTON.............................9-40
CONNECTING ROD - INSTALLATION,
PISTON.............................9-41
CONNECTING ROD - OPERATION,
PISTON.............................9-40
CONNECTING ROD - REMOVAL, PISTON . . . 9-40
CONNECTING ROD, FITTING.............9-32
CONNECTOR - INSTALLATION, TRAILER
TOW ..............................8L-61
CONNECTOR - REMOVAL, TRAILER TOW . . 8L-61
CONTAINER - DESCRIPTION, COOLANT
RECOVERY PRESS....................7-20
CONTAINER - OPERATION, COOLANT
RECOVERY PRESS....................7-20
CONTROL ARM BUSHING -
INSTALLATION, LOWER.................2-3
CONTROL ARM BUSHING - REMOVAL,
LOWER..............................2-2
CONTROL ARM BUSHINGS -
INSTALLATION, UPPER..................2-4
CONTROL ARM BUSHINGS - REMOVAL,
UPPER...............................2-3
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-2
CONVERTER - INSPECTION, CATALYTIC....11-3
CONVERTER - INSTALLATION, CATALYTIC . . 11-3
CONVERTER - REMOVAL, CATALYTIC......11-2
COOLANT - DESCRIPTION, ENGINE.......7-19
COOLANT - DESCRIPTION, HOAT
.........7-18
COOLANT RECOVERY PRESS
CONTAINER - DESCRIPTION
.............7-20
COOLANT RECOVERY PRESS
CONTAINER - OPERATION
...............7-20
COOLANT TEMPERATURE SENSOR -
DESCRIPTION, ENGINE
.................7-21
COOLANT TEMPERATURE SENSOR -
INSTALLATION, ENGINE
................7-22
KJINDEX 1
Description Group-Page Description Group-Page Description Group-Page

COOLANT TEMPERATURE SENSOR -
OPERATION, ENGINE...................7-21
COOLANT TEMPERATURE SENSOR -
REMOVAL, ENGINE....................7-21
COOLER - DESCRIPTION, TRANS.........7-30
COOLERS AND TUBES - STANDARD
PROCEDURE, FLUSHING................7-30
COOLING, SPECIAL TOOLS..............7-13
COOLING SYSTEM - OPERATION..........7-2
COOLING SYSTEM - REVERSE
FLUSHING - STANDARD PROCEDURE.....7-12
COOLING SYSTEM - STANDARD
PROCEDURE, DRAINING................7-11
COOLING SYSTEM - STANDARD
PROCEDURE, REFILLING................7-11
COOLING SYSTEM 2.4L ENGINE -
DESCRIPTION.........................7-1
COOLING SYSTEM DIAGNOSIS CHART -
DIAGNOSIS AND TESTING...............7-5
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-2
CORE AND OIL GALLERY PLUGS -
STANDARD PROCEDURE, ENGINE.........9-9
COVER - CLEANING, CYLINDER HEAD.....9-26
COVER - INSPECTION, CYLINDER HEAD . . . 9-26
COVER - INSTALLATION, CYLINDER
HEAD...............................9-26
COVER - REMOVAL, CYLINDER HEAD.....9-26
COVER(S) - INSTALLATION, TIMING
BELT ...............................9-53
COVER(S) - REMOVAL, TIMING BELT......9-53
CRANKSHAFT - DESCRIPTION...........9-32
CRANKSHAFT - INSPECTION.............9-34
CRANKSHAFT - INSTALLATION...........9-34
CRANKSHAFT - OPERATION.............9-33
CRANKSHAFT - REMOVAL..............9-33
CRANKSHAFT END PLAY - STANDARD
PROCEDURE.........................9-33
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........................9-37
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL...........................9-37
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........................9-39
CRANKSHAFT OIL SEAL - REAR -
REMOVAL...........................9-38
CRANKSHAFT SPROCKET -
INSTALLATION........................9-56
CRANKSHAFT SPROCKET - REMOVAL.....9-55
CROSS-OVER PIPE - INSTALLATION.......11-4
CROSS-OVER PIPE - REMOVAL..........11-4
CYLINDER BORE FITTING - STANDARD
PROCEDURE, PISTON TO...............9-30
CYLINDER BORE HONING - STANDARD
PROCEDURE.........................9-31
CYLINDER COMBUSTION PRESSURE
LEAKAGE TEST - DIAGNOSIS AND
TESTING.............................9-3
CYLINDER COMPRESSION PRESSURE
TEST - DIAGNOSIS AND TESTING.........9-3
CYLINDER HEAD - CLEANING............9-20
CYLINDER HEAD - DESCRIPTION.........9-19
CYLINDER HEAD - INSPECTION..........9-21
CYLINDER HEAD - INSTALLATION........9-21
CYLINDER HEAD - OPERATION...........9-19
CYLINDER HEAD - REMOVAL............9-20
CYLINDER HEAD COVER - CLEANING......9-26
CYLINDER HEAD COVER - INSPECTION....9-26
CYLINDER HEAD COVER -
INSTALLATION
........................9-26
CYLINDER HEAD COVER - REMOVAL
......9-26
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING
........................9-19
CYLINDER HEAD OFF - INSTALLATION
.....9-28
CYLINDER HEAD OFF - REMOVAL
........9-27
CYLINDER HEAD ON - INSTALLATION
.....9-28
CYLINDER HEAD ON - REMOVAL
.........9-27
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR OF
.......9-9
DAMPER - INSTALLATION, VIBRATION
.....9-43
DAMPER - REMOVAL, VIBRATION
........9-43
DAYTIME RUNNING LAMP RELAY -
DESCRIPTION
.......................8L-20
DAYTIME RUNNING LAMP RELAY -
INSTALLATION
.......................8L-21
DAYTIME RUNNING LAMP RELAY -
OPERATION
.........................8L-20DAYTIME RUNNING LAMP RELAY -
REMOVAL..........................8L-21
DESCRIPTION - OPERATION.............7-20
DESCRIPTION, BACKUP LAMP SWITCH . . . 8L-15
DESCRIPTION, BALANCE SHAFT..........9-59
DESCRIPTION, BRAKE LAMP SWITCH....8L-16
DESCRIPTION, CAMSHAFT(S)............9-23
DESCRIPTION, CATALYTIC CONVERTER....11-2
DESCRIPTION, COMBINATION FLASHER . . . 8L-19
DESCRIPTION, COOLANT RECOVERY
PRESS CONTAINER....................7-20
DESCRIPTION, COOLING SYSTEM 2.4L
ENGINE..............................7-1
DESCRIPTION, CRANKSHAFT............9-32
DESCRIPTION, CYLINDER HEAD..........9-19
DESCRIPTION, DAYTIME RUNNING
LAMP RELAY........................8L-20
DESCRIPTION, ENGINE - 2.4L.............9-3
DESCRIPTION, ENGINE BLOCK...........9-30
DESCRIPTION, ENGINE BLOCK HEATER -
2.4L................................7-20
DESCRIPTION, ENGINE COOLANT.........7-19
DESCRIPTION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
DESCRIPTION, ENGINE MOUNTING.......9-44
DESCRIPTION, EXHAUST MANIFOLD......9-53
DESCRIPTION, EXHAUST SYSTEM........11-1
DESCRIPTION, FRONT FOG LAMP RELAY . . 8L-22
DESCRIPTION, HAZARD SWITCH........8L-28
DESCRIPTION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
DESCRIPTION, HEADLAMP LEVELING
MOTOR............................8L-35
DESCRIPTION, HEADLAMP LEVELING
SWITCH............................8L-37
DESCRIPTION, HEADLAMP LOW BEAM
RELAY.............................8L-39
DESCRIPTION, HEAT SHIELDS...........11-4
DESCRIPTION, HOAT COOLANT..........7-18
DESCRIPTION, HOSE CLAMPS............7-1
DESCRIPTION, INTAKE MANIFOLD........9-51
DESCRIPTION, INTAKE/EXHAUST VALVES
& SEATS ............................9-27
DESCRIPTION, LAMP BAR.............8L-65
DESCRIPTION, LAMP BAR SWITCH......8L-67
DESCRIPTION, LAMPS/LIGHTING -
EXTERIOR...........................8L-2
DESCRIPTION, LUBRICATION............9-46
DESCRIPTION, MUFFLER...............11-4
DESCRIPTION, MULTI-FUNCTION
SWITCH............................8L-46
DESCRIPTION, OIL FILTER..............9-47
DESCRIPTION, OIL PRESSURE
SENSOR/SWITCH.....................9-48
DESCRIPTION, PARK LAMP RELAY.......8L-54
DESCRIPTION, PISTON & CONNECTING
ROD................................9-40
DESCRIPTION, RADIATOR...............7-22
DESCRIPTION, RADIATOR FAN -
ELECTRIC...........................7-26
DESCRIPTION, RADIATOR PRESSURE
CAP ................................7-25
DESCRIPTION, REAR FOG LAMP RELAY . . . 8L-56
DESCRIPTION, TRAILER TOW RELAY.....8L-62
DESCRIPTION, TRAILER TOW WIRING....8L-64
DESCRIPTION, TRANS COOLER..........7-30
DESCRIPTION, WATER PUMP - 2.4L......7-27
DIAGNOSIS - DIAGNOSIS AND TESTING,
LASH ADJUSTER (TAPPET) NOISE........9-28
DIAGNOSIS - DIAGNOSIS AND TESTING,
SERPENTINE DRIVE BELT...............7-15
DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, BACKUP
LAMP SWITCH......................8L-15
DIAGNOSIS AND TESTING, BRAKE LAMP
SWITCH............................8L-17
DIAGNOSIS AND TESTING, COOLING
SYSTEM DIAGNOSIS CHART
..............7-5
DIAGNOSIS AND TESTING, COOLING
SYSTEM LEAKS
........................7-2
DIAGNOSIS AND TESTING, CYLINDER
COMBUSTION PRESSURE LEAKAGE
TEST
................................9-3
DIAGNOSIS AND TESTING, CYLINDER
COMPRESSION PRESSURE TEST
..........9-3
DIAGNOSIS AND TESTING, CYLINDER
HEAD GASKET
........................9-19DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, ENGINE
DIAGNOSIS - PERFORMANCE.............9-5
DIAGNOSIS AND TESTING, ENGINE
MECHANICAL.........................9-7
DIAGNOSIS AND TESTING, ENGINE OIL
LEAK INSPECTION......................9-4
DIAGNOSIS AND TESTING, ENGINE OIL
PRESSURE CHECKING.................9-46
DIAGNOSIS AND TESTING, EXHAUST
SYSTEM............................11-2
DIAGNOSIS AND TESTING, FRONT FOG
LAMP RELAY........................8L-23
DIAGNOSIS AND TESTING, HEADLAMP
HIGH BEAM RELAY...................8L-34
DIAGNOSIS AND TESTING, HEADLAMP
LEVELING SWITCH...................8L-37
DIAGNOSIS AND TESTING, HEADLAMP
LOW BEAM RELAY...................8L-40
DIAGNOSIS AND TESTING, INTAKE
MANIFOLD LEAKS.....................9-51
DIAGNOSIS AND TESTING, LAMP BAR....8L-65
DIAGNOSIS AND TESTING, LAMPS/
LIGHTING - EXTERIOR.................8L-7
DIAGNOSIS AND TESTING, LASH
ADJUSTER (TAPPET) NOISE
DIAGNOSIS..........................9-28
DIAGNOSIS AND TESTING, MULTI-
FUNCTION SWITCH...................8L-50
DIAGNOSIS AND TESTING, ON-BOARD
DIAGNOSTICS (OBD)....................7-2
DIAGNOSIS AND TESTING, PARK LAMP
RELAY.............................8L-55
DIAGNOSIS AND TESTING,
PRELIMINARY CHECKS..................7-2
DIAGNOSIS AND TESTING, RADIATOR
PRESSURE CAP.......................7-25
DIAGNOSIS AND TESTING, REAR FOG
LAMP RELAY........................8L-57
DIAGNOSIS AND TESTING, SERPENTINE
DRIVE BELT DIAGNOSIS................7-15
DIAGNOSIS AND TESTING, TRAILER
TOW RELAY.........................8L-62
DIAGNOSIS CHART - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-5
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-2
DISASSEMBLY, OIL PUMP...............9-49
DRAINING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
DRIVE BELT DIAGNOSIS - DIAGNOSIS
AND TESTING, SERPENTINE.............7-15
ELECTRIC - DESCRIPTION, RADIATOR
FAN ................................7-26
ELECTRIC - INSTALLATION, RADIATOR
FAN ................................7-27
ELECTRIC - OPERATION, RADIATOR FAN . . . 7-26
ELECTRIC - REMOVAL, RADIATOR FAN....7-26
END PLAY - STANDARD PROCEDURE,
CRANKSHAFT........................9-33
END-PLAY - STANDARD PROCEDURE,
CAMSHAFT..........................9-23
ENGINE - 2.4L - DESCRIPTION............9-3
ENGINE - DESCRIPTION, COOLING
SYSTEM 2.4L.........................7-1
ENGINE - DIAGNOSIS AND TESTING.......9-5
ENGINE - INSTALLATION, 2.4L . . 7-14,7-17,7-22,
7-28
ENGINE - REMOVAL, 2.4L . . . 7-14,7-16,7-22,7-27
ENGINE - SPECIFICATIONS, 2.4L.........9-13
ENGINE - STANDARD PROCEDURE,
HYDROSTATIC LOCKED..................9-9
ENGINE ASSEMBLY - INSTALLATION......9-12
ENGINE ASSEMBLY - REMOVAL..........9-12
ENGINE BLOCK - DESCRIPTION..........9-30
ENGINE BLOCK HEATER - 2.4L -
DESCRIPTION........................7-20
ENGINE BLOCK HEATER - 2.4L -
OPERATION..........................7-20
ENGINE COOLANT - DESCRIPTION
........7-19
ENGINE COOLANT TEMPERATURE
SENSOR - DESCRIPTION
...............7-21
ENGINE COOLANT TEMPERATURE
SENSOR - INSTALLATION
...............7-22
ENGINE COOLANT TEMPERATURE
SENSOR - OPERATION
.................7-21
ENGINE COOLANT TEMPERATURE
SENSOR - REMOVAL
...................7-21
2 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page