2002 JEEP LIBERTY sunroof

(5) Connect wire harness.
(6) Install the headliner. (Refer to 23 - BODY/IN-
TERIOR/HEADLINER - INSTALLATION)
(7) Install the opening trim lace. (Refer to 23 -
BODY/SUNROOF/OPENING TRIM LACE - INSTAL-
LATION)
(8) Connect battery negative cable.
(9) Test sunroof operation, adjust as necessary.
(Refer to 23 - BODY/SUNROOF/GLASS PANEL -
ADJUSTMENTS)
DRIVE MOTOR
REMOVAL
(1) Remove headliner. (Refer to 23 - BODY/INTE-
RIOR/HEADLINER - REMOVAL)
(2) Cut wire retaining tape being careful not to cut
wires.
(3) Disconnect the electrical connector (Fig. 11).
(4) Remove three motor assembly attaching screws
from bottom side of motor assembly and remove
motor assembly from the motor bracket.
INSTALLATION
(1) Place motor into position and install screws
attaching motor to bracket.
NOTE: Hold electronics module to motor bracket
when inserting motor shaft to avoid disengaging
drive cables.
(2) Connect electrical connector.
(3) Tape wires to drive cables to prevent rattles.
Fig. 9 WIRE HARNESS
1 - CLIPS
2 - ELECTRICAL CONNECTOR
3 - WIRE HARNESS
Fig. 10 MODULE ASSEMBLY
1 - U-NUTS
2 - DRIVE MOTOR
3 - BOLTS
4 - GLASS OPENING
5 - MODULE ASSEMBLY
Fig. 11 DRIVE MOTOR ASSEMBLY
1 - CONTROL MODULE
2 - SCREWS
3 - DRIVE MOTOR
4 - SCREW
5 - ELECTRICAL CONNECTOR
23 - 182 SUNROOFKJ
MODULE ASSEMBLY (Continued)

(4) Test sunroof operation, adjust as necessary.
(5) Install headliner. (Refer to 23 - BODY/INTERI-
OR/HEADLINER - INSTALLATION)
CONTROL MODULE
REMOVAL
(1) Remove the module assembly. (Refer to 23 -
BODY/SUNROOF/MODULE ASSEMBLY -
REMOVAL)
(2) Remove three motor assembly retaining screws
from bottom side of motor, and remove motor assem-
bly (Fig. 11).
(3) From top side of module assembly, remove one
attaching screw from electronics module. (Fig. 12)
(4) Remove old timing module.
INSTALLATION
(1) Check glass assembly position. Adjust to full
closed position. Insert pin into holes in lift arm
assembly to check position (Fig. 13).
(2) Set new electronic module in position on top
side of motor mounting bracket engaging drive cables
with pinion gear in electronics module.
(3) Install one screw to attach electronics module
to motor bracket. Tighten screw to 3 N´m (27 in. lbs.)
torque.
(4) Install motor assembly to motor bracket and
electronics module with three screws. Tighten screw
to 1.75 N´m (15.5 in. lbs.) torque.
(5) Remove the new module's timing pin and dis-
card. (Fig. 14)(6) Connect electrical connector to module assem-
bly wire harness. Secure any loose wires.
(7) Install module assembly. (Refer to 23 - BODY/
SUNROOF/MODULE ASSEMBLY - INSTALLA-
TION)
(8) Test operation, adjust as necessary. (Refer to 23
- BODY/SUNROOF/GLASS PANEL - ADJUST-
MENTS)
(9) Install opening trim lace. (Refer to 23 - BODY/
SUNROOF/OPENING TRIM LACE - INSTALLA-
TION)
Fig. 12 CONTROL MODULE
1 - MOTOR BRACKET
2 - CABLES
3 - SCREW
4 - CONTROL MODULE
Fig. 13 LIFT ARM POSITIONING
1 - GLASS BRACKET
2 - LIFT ARM
3 - ALIGNMENT PIN
Fig. 14 MODULE TIMING PIN
1 - CONTROL MODULE
2 - TIMING PIN
KJSUNROOF 23 - 183
DRIVE MOTOR (Continued)

CONTROL SWITCH
DESCRIPTION
Vehicles equipped with a power sunroof utilize an
sunroof control switch. On this model, the sunroof
control switch is located in the overhead console, in
between the two reading lamps. The switch is
mounted in the overhead console with four plastic
retaining tabs, molded into the switch housing.
This switch incorporates four selections of opera-
tion open, auto open, close and vent. The individual
switches in the sunroof control switch unit cannot be
repaired. If one switch is damaged or faulty, the
entire sunroof control switch unit must be replaced.
OPERATION
With the operation of the sunroof control switch,
voltage is directed to the sunroof motor, through the
switch contacts or control module. If the control
switch is depressed and held depressed the voltage
signal is controlled manually through the switch con-
tacts, so when the switch is released the sunroof
stops.
Refer to the owners manual for more information
on the operation of the sunroof switch and system.
DIAGNOSIS AND TESTING
The following test will determine if the sunroof
control switch is operating properly.
(1) Remove the overhead console from the head-
liner (Refer to 8 - ELECTRICAL/OVERHEAD CON-
SOLE - REMOVAL).
(2) Remove the sunroof control switch from the
overhead console (Refer to 23 - BODY/SUNROOF/
CONTROL SWITCH - REMOVAL).
(3) Using an ohmmeter, test the switch terminals
for proper continuity using the table below. If any ofthe terminals do not show proper continuity, replace
the sunroof control switch.
SWITCH POSITION
(DEPRESSED)CONTINUITY BETWEEN
TERMINALS
VENT (V) 3, 4
OPEN (AUTO) 1, 4
CLOSE 2, 4
REMOVAL
(1) Disconnect and isolate the negative battery
cable.
(2) Remove the overhead console from the head-
liner (Refer to 8 - ELECTRICAL/OVERHEAD CON-
SOLE - REMOVAL).
(3) Disconnect the sunroof control switch electrical
connector. Depress the connector retaining tab and
pull the connector straight out.
(4) To remove the switch from the overhead con-
sole, push on the back of the switch until it comes
free from the overhead console.
INSTALLATION
(1) Install the switch in the overhead console
assembly. Be certain the switch is securely snapped
in place.
(2) Connect the sunroof control switch electrical
connector. Be certain the switch connector is securely
snapped in place.
(3) Install the overhead console (Refer to 8 -
ELECTRICAL/OVERHEAD CONSOLE - INSTALLA-
TION).
(4) Connect the negative battery cable.
23 - 184 SUNROOFKJ

ABS - DESCRIPTION, BRAKES...........5-32
ABS - OPERATION, BRAKES.............5-32
ABS - SPECIFICATIONS, BRAKES.........5-33
ABS BRAKE BLEEDING - STANDARD
PROCEDURE.........................5-33
ABS INDICATOR - DESCRIPTION.........8J-11
ABS INDICATOR - OPERATION..........8J-11
A/C APPLICATION TABLE,
SPECIFICATIONS......................24-9
A/C COMPRESSOR CLUTCH -
INSPECTION........................24-14
A/C COMPRESSOR CLUTCH -
INSTALLATION.......................24-14
A/C COMPRESSOR CLUTCH - REMOVAL . . 24-13
A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-12
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-12
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-15
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-16
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-15
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-16
A/C COMPRESSOR NOISE - DIAGNOSIS
AND TESTING.......................24-42
A/C CONDENSER - DESCRIPTION........24-45
A/C CONDENSER - INSTALLATION.......24-46
A/C CONDENSER - OPERATION...........24-45
A/C CONDENSER - REMOVAL...........24-45
A/C DISCHARGE LINE - INSTALLATION . . . 24-47
A/C DISCHARGE LINE - REMOVAL.......24-46
A/C EVAPORATOR - DESCRIPTION.......24-49
A/C EVAPORATOR - INSTALLATION......24-49
A/C EVAPORATOR - OPERATION.........24-49
A/C EVAPORATOR - REMOVAL..........24-49
A/C HEATER CONTROL - DESCRIPTION . . . 24-16
A/C HEATER CONTROL - INSTALLATION . . . 24-17
A/C HEATER CONTROL - REMOVAL......24-17
A/C HIGH PRESSURE SWITCH -
DESCRIPTION.......................24-17
A/C HIGH PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-18
A/C HIGH PRESSURE SWITCH -
INSTALLATION.......................24-18
A/C HIGH PRESSURE SWITCH -
OPERATION.........................24-18
A/C HIGH PRESSURE SWITCH -
REMOVAL..........................24-18
A/C LIQUID LINE - INSTALLATION.......24-47
A/C LIQUID LINE - REMOVAL...........24-47
A/C LOW PRESSURE SWITCH -
DESCRIPTION.......................24-18
A/C LOW PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-19
A/C LOW PRESSURE SWITCH -
INSTALLATION.......................24-19
A/C LOW PRESSURE SWITCH -
OPERATION.........................24-18
A/C LOW PRESSURE SWITCH -
REMOVAL..........................24-19
A/C ORIFICE TUBE - DESCRIPTION.......24-50
A/C ORIFICE TUBE - INSTALLATION......24-50
A/C ORIFICE TUBE - OPERATION........24-50
A/C ORIFICE TUBE - REMOVAL..........24-50
A/C PERFORMANCE - DIAGNOSIS AND
TESTING............................24-2
A/C SUCTION LINE - INSTALLATION......24-49
A/C SUCTION LINE - REMOVAL.........24-48
ACCELERATOR PEDAL - INSTALLATION . . . 14-30
ACCELERATOR PEDAL - REMOVAL.......14-29
ACCESS PANEL - DESCRIPTION, LATCH . . 23-139
ACCESS PANEL - INSTALLATION, LATCH . 23-139
ACCESS PANEL - REMOVAL, LATCH.....23-139
ACCUMULATOR - DESCRIPTION.........24-51
ACCUMULATOR - INSTALLATION........24-51
ACCUMULATOR - OPERATION..........24-51
ACCUMULATOR - REMOVAL
............24-51
ACTUATION TEST MODE - DESCRIPTION,
CIRCUIT
.............................25-2
ACTUATOR - INSTALLATION, BLEND
DOOR
.............................24-20
ACTUATOR - INSTALLATION, FLOOR -
DEFROST DOOR
.....................24-25
ACTUATOR - INSTALLATION, PANEL
DOOR
.............................24-25ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-26
ACTUATOR - REMOVAL, BLEND DOOR....24-20
ACTUATOR - REMOVAL, FLOOR -
DEFROST DOOR.....................24-24
ACTUATOR - REMOVAL, PANEL DOOR....24-24
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-26
ADAPTER - INSTALLATION, DISC BRAKE
CALIPER............................5-18
ADAPTER - REMOVAL, DISC BRAKE
CALIPER............................5-18
ADAPTER HOUSING SEAL -
INSTALLATION......................21-124
ADAPTER HOUSING SEAL - REMOVAL . . . 21-124
ADAPTOR - REMOVAL, DEFROST
DUCT/DEMISTER.....................24-32
ADHESIVE LOCATIONS -
SPECIFICATIONS, WELD AND
STRUCTURAL........................23-9
ADJUSTER - DIAGNOSIS AND TESTING,
HYDRAULIC LASH.................9-19,9-30
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-38
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-37
ADJUSTMENT - STANDARD
PROCEDURE, CAMBER AND CASTER.......2-5
ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER AND
TOE .................................2-5
ADJUSTMENT - STANDARD
PROCEDURE, COMPASS VARIATION......8M-3
ADJUSTMENT - STANDARD
PROCEDURE, TOE......................2-5
ADJUSTMENT, ADJUSTMENTS . . . 23-119,23-124,
23-131
ADJUSTMENT, ADJUSTMENTS...........3-55
ADJUSTMENT, ADJUSTMENTS -
SUNROOF GLASS PANEL.............23-178
ADJUSTMENT, FRONT FOG LAMP UNIT . . . 8L-25
ADJUSTMENT, HEADLAMP UNIT.........8L-42
ADJUSTMENT, LOCK OUT...............5-30
ADJUSTMENT, REAR DRUM BRAKE.......5-12
ADJUSTMENTS - ADJUSTMENT . . 23-119,23-124,
23-131
ADJUSTMENTS - ADJUSTMENT..........3-55
ADJUSTMENTS - SUNROOF GLASS
PANEL ADJUSTMENT................23-178
ADJUSTMENTS, FRONT AXLE - 186FIA....3-25
ADJUSTMENTS, GEARSHIFT CABLE.....21-130
ADJUSTMENTS, PARK-INTERLOCK
CABLE............................21-154
ADJUSTMENTS, REAR AXLE - 8 1/4 .......3-92
AFTER A SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE.................8O-6
AIR CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING...........................21-80
AIR CONDITIONER - DESCRIPTION,
HEATER .............................24-1
AIR CONDITIONER - OPERATION,
HEATER .............................24-2
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-35
AIR CONTROL MOTOR - INSTALLATION,
IDLE...............................14-36
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-35
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-36
AIR TEMPERATURE SENSOR -
DESCRIPTION, INTAKE................14-36
AIR TEMPERATURE SENSOR -
INSTALLATION, INTAKE................14-38
AIR TEMPERATURE SENSOR -
OPERATION, INTAKE..................14-36
AIR TEMPERATURE SENSOR -
REMOVAL, INTAKE...................14-37
AIRBAG - DESCRIPTION, DRIVER........8O-17
AIRBAG - DESCRIPTION, PASSENGER....8O-27
AIRBAG - DESCRIPTION, SIDE CURTAIN . . 8O-38
AIRBAG - INSTALLATION, DRIVER.......8O-20
AIRBAG - INSTALLATION, PASSENGER
. . . 8O-29
AIRBAG - INSTALLATION, SIDE CURTAIN
. . 8O-41
AIRBAG - OPERATION, DRIVER
.........8O-18
AIRBAG - OPERATION, PASSENGER
......8O-27
AIRBAG - OPERATION, SIDE CURTAIN
....8O-39AIRBAG - REMOVAL, DRIVER...........8O-19
AIRBAG - REMOVAL, PASSENGER.......8O-28
AIRBAG - REMOVAL, SIDE CURTAIN.....8O-40
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-9
AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE IMPACT...........8O-43
AIRBAG CONTROL MODULE -
INSTALLATION......................8O-12
AIRBAG CONTROL MODULE -
INSTALLATION, SIDE IMPACT...........8O-45
AIRBAG CONTROL MODULE -
OPERATION.........................8O-10
AIRBAG CONTROL MODULE -
OPERATION, SIDE IMPACT.............8O-43
AIRBAG CONTROL MODULE - REMOVAL . . 8O-11
AIRBAG CONTROL MODULE - REMOVAL,
SIDE IMPACT.......................8O-44
AIRBAG DOOR - INSTALLATION,
PASSENGER........................8O-30
AIRBAG DOOR - REMOVAL, PASSENGER . . 8O-29
AIRBAG INDICATOR - DESCRIPTION......8J-12
AIRBAG INDICATOR - OPERATION.......8J-12
AIRBAG MOUNTING BRACKET -
INSTALLATION, PASSENGER...........8O-31
AIRBAG MOUNTING BRACKET -
REMOVAL, PASSENGER...............8O-31
AJAR INDICATOR - DESCRIPTION, DOOR . . 8J-17
AJAR INDICATOR - DESCRIPTION, GATE . . 8J-20
AJAR INDICATOR - DESCRIPTION,
GLASS..............................8J-21
AJAR INDICATOR - OPERATION, DOOR . . . 8J-17
AJAR INDICATOR - OPERATION, GATE....8J-20
AJAR INDICATOR - OPERATION, GLASS . . . 8J-21
AJAR SWITCH - DESCRIPTION, DOOR....8L-77
AJAR SWITCH - DESCRIPTION, FLIP-UP
GLASS.............................8L-77
AJAR SWITCH - DESCRIPTION, HOOD....8Q-11
AJAR SWITCH - DESCRIPTION,
TAILGATE...........................8L-82
AJAR SWITCH - DIAGNOSIS AND
TESTING, HOOD.....................8Q-12
AJAR SWITCH - INSTALLATION, HOOD . . . 8Q-12
AJAR SWITCH - OPERATION, DOOR......8L-77
AJAR SWITCH - OPERATION, FLIP-UP
GLASS.............................8L-77
AJAR SWITCH - OPERATION, HOOD.....8Q-12
AJAR SWITCH - OPERATION, TAILGATE . . . 8L-82
AJAR SWITCH - REMOVAL, HOOD.......8Q-12
AJAR SWITCH BRACKET -
INSTALLATION, HOOD.................8Q-13
AJAR SWITCH BRACKET - REMOVAL,
HOOD.............................8Q-13
AJAR SWITCH STRIKER -
INSTALLATION, HOOD.................8Q-14
AJAR SWITCH STRIKER - REMOVAL,
HOOD.............................8Q-13
ALIGNMENT - DESCRIPTION, WHEEL.......2-3
ALIGNMENT - OPERATION, WHEEL........2-3
ALIGNMENT, SPECIFICATIONS............2-6
ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE...............21-81
AMBIENT TEMP SENSOR - DESCRIPTION . . 8M-9
AMBIENT TEMP SENSOR - OPERATION . . . 8M-9
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING..............8M-9
AMBIENT TEMPERATURE SENSOR
CIRCUIT - DIAGNOSIS AND TESTING.....8M-9
AMPERAGE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP.................14-16
AMPLIFIER CHOKE AND RELAY -
DESCRIPTION........................8A-3
AMPLIFIER CHOKE AND RELAY -
DIAGNOSIS AND TESTING..............8A-4
AMPLIFIER CHOKE AND RELAY -
INSTALLATION.......................8A-4
AMPLIFIER CHOKE AND RELAY -
OPERATION..........................8A-3
AMPLIFIER CHOKE AND RELAY -
REMOVAL...........................8A-4
ANCHOR - DESCRIPTION, CHILD TETHER
. 8O-13
ANCHOR - OPERATION, CHILD TETHER
. . . 8O-13
ANGLE - STANDARD PROCEDURES,
PROPELLER SHAFT
.....................3-3
ANTENNA BODY & CABLE -
DESCRIPTION
........................8A-4
ANTENNA BODY & CABLE -
INSTALLATION
.......................8A-6
KJINDEX 1
Description Group-Page Description Group-Page Description Group-Page

FUEL PRESSURE REGULATOR -
DESCRIPTION.......................14-13
FUEL PRESSURE REGULATOR -
INSTALLATION.......................14-14
FUEL PRESSURE REGULATOR -
OPERATION.........................14-14
FUEL PRESSURE REGULATOR -
REMOVAL..........................14-14
FUEL PUMP - DESCRIPTION............14-15
FUEL PUMP - OPERATION.............14-15
FUEL PUMP AMPERAGE TEST -
DIAGNOSIS AND TESTING.............14-16
FUEL PUMP CAPACITY TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP MODULE - DESCRIPTION....14-18
FUEL PUMP MODULE - INSTALLATION . . . 14-19
FUEL PUMP MODULE - OPERATION......14-18
FUEL PUMP MODULE - REMOVAL.......14-18
FUEL PUMP PRESSURE TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP RELAY - DESCRIPTION......14-34
FUEL PUMP RELAY - DIAGNOSIS AND
TESTING...........................14-34
FUEL PUMP RELAY - INSTALLATION.....14-34
FUEL PUMP RELAY - OPERATION........14-34
FUEL PUMP RELAY - REMOVAL.........14-34
FUEL PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD........................8I-4
FUEL RAIL - DESCRIPTION.............14-21
FUEL RAIL - INSTALLATION..............14-24
FUEL RAIL - OPERATION...............14-21
FUEL RAIL - REMOVAL................14-22
FUEL SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE................14-4
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-5
FUEL SYSTEM, SPECIAL TOOLS..........14-6
FUEL TANK - DESCRIPTION............14-24
FUEL TANK - INSTALLATION............14-27
FUEL TANK - OPERATION..............14-24
FUEL TANK - REMOVAL...............14-25
FUEL TANK CHECK VALVE -
DESCRIPTION.......................14-28
FUEL TANK CHECK VALVE -
INSTALLATION.......................14-28
FUEL TANK CHECK VALVE - OPERATION . . 14-28
FUEL TANK CHECK VALVE - REMOVAL....14-28
FUEL TANK SKID PLATE - INSTALLATION . . . 13-9
FUEL TANK SKID PLATE - REMOVAL......13-9
FULL TIME INDICATOR - DESCRIPTION . . . 8J-29
FULL TIME INDICATOR - OPERATION.....8J-30
FUNCTION - DIAGNOSIS AND TESTING,
REAR HVAC CONTROL ASSEMBLY
WINDOW DEFOGGER..................8G-9
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-3
FUSE - INSTALLATION, IOD..........8W-97-3
FUSE - OPERATION, IOD.............8W-97-3
FUSE - REMOVAL, IOD..............8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.......8W-01-9
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL.....9-10
GAP AND FLUSH - SPECIFICATIONS.....23-116
GAS ENGINES - GENERATOR RATINGS....8F-23
GAS POWERED - STARTER MOTOR......8F-39
GAS POWERED - TORQUE
.............8F-38
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD
..................9-19,9-30
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE
.........9-9
GATE - INSTALLATION, SWING
.........23-138
GATE - REMOVAL, SWING
............23-138
GATE AJAR INDICATOR - DESCRIPTION
. . . 8J-20
GATE AJAR INDICATOR - OPERATION
.....8J-20
GATE BELTLINE WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE BELTLINE WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GATE OPENING WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE OPENING WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE
......................8J-18
GAUGE - DESCRIPTION, FUEL
...........8J-19GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-18
GAUGE - OPERATION, FUEL............8J-20
GEAR - DESCRIPTION.................19-13
GEAR - INSTALLATION, PINION
GEAR/RING..........................3-46
GEAR - OPERATION...................19-13
GEAR - REMOVAL, PINION GEAR/RING....3-44
GEAR/RING GEAR - INSTALLATION,
PINION.............................3-46
GEAR/RING GEAR - REMOVAL, PINION....3-44
GEAR/RING GEAR/TONE RING -
INSTALLATION, PINION............3-112,3-82
GEAR/RING GEAR/TONE RING -
REMOVAL, PINION...............3-110,3-79
GEARSHIFT CABLE - ADJUSTMENTS....21-130
GEARSHIFT CABLE - DIAGNOSIS AND
TESTING..........................21-128
GEARSHIFT CABLE - INSTALLATION.....21-129
GEARSHIFT CABLE - REMOVAL........21-128
GEAR/TONE RING - INSTALLATION,
PINION GEAR/RING...............3-112,3-82
GEAR/TONE RING - REMOVAL, PINION
GEAR/RING.....................3-110,3-79
GEARTRAIN - ASSEMBLY, PLANETARY . . . 21-160
GEARTRAIN - CLEANING, PLANETARY . . . 21-159
GEARTRAIN - DESCRIPTION,
PLANETARY........................21-157
GEARTRAIN - DISASSEMBLY,
PLANETARY........................21-159
GEARTRAIN - INSPECTION, PLANETARY . 21-159
GEARTRAIN - OPERATION, PLANETARY . . 21-157
GENERAL - WARNINGS.............8W-01-7
GENERATOR - DESCRIPTION...........8F-25
GENERATOR - INSTALLATION...........8F-26
GENERATOR - OPERATION.............8F-25
GENERATOR - REMOVAL...............8F-25
GENERATOR DECOUPLER - DIAGNOSIS
AND TESTING.......................8F-27
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-26
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-30
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-27
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-27
GENERATOR RATINGS, GAS ENGINES....8F-23
GLASS - INSTALLATION, DOOR . . 23-122,23-129,
23-172
GLASS - INSTALLATION, FLIP-UP.......23-136
GLASS - REMOVAL, DOOR......23-122,23-129,
23-172
GLASS - REMOVAL, FLIP-UP..........23-136
GLASS AJAR INDICATOR - DESCRIPTION . . 8J-21
GLASS AJAR INDICATOR - OPERATION . . . 8J-21
GLASS AJAR SWITCH - DESCRIPTION,
FLIP-UP............................8L-77
GLASS AJAR SWITCH - OPERATION,
FLIP-UP............................8L-77
GLASS HEATING GRID REPAIR -
STANDARD PROCEDURE, REAR..........8G-4
GLASS LATCH - INSTALLATION, FLIP-UP . 23-136
GLASS LATCH - REMOVAL, FLIP-UP.....23-136
GLASS PANEL - INSTALLATION........23-178
GLASS PANEL - REMOVAL............23-178
GLASS PANEL ADJUSTMENT,
ADJUSTMENTS - SUNROOF...........23-178
GLASS PANEL SEAL - INSTALLATION
....23-178
GLASS PANEL SEAL - REMOVAL
.......23-178
GLASS RELEASE SWITCH - DIAGNOSIS
AND TESTING, FLIP-UP
................8N-5
GLASS RUN CHANNEL - INSTALLATION
. 23-123,
23-130
GLASS RUN CHANNEL - REMOVAL
.....23-123,
23-130
GLASS SUPPORT CYLINDER -
INSTALLATION, FLIP-UP
..............23-139
GLASS SUPPORT CYLINDER -
REMOVAL, FLIP-UP
..................23-139
GLOVE BOX - INSTALLATION
..........23-148
GLOVE BOX - REMOVAL
..............23-148
GLOVE BOX LATCH - INSTALLATION
....23-148
GLOVE BOX LATCH - REMOVAL
........23-148
GLOVE BOX LATCH STRIKER -
INSTALLATION
......................23-149
GLOVE BOX LATCH STRIKER - REMOVAL
. 23-148GRAB HANDLE - INSTALLATION,
A-PILLAR TRIM.....................23-156
GRAB HANDLE - REMOVAL, A-PILLAR
TRIM.............................23-156
GRID - DESCRIPTION, REAR WINDOW
DEFOGGER..........................8G-5
GRID - DIAGNOSIS AND TESTING, REAR
WINDOW DEFOGGER..................8G-5
GRID - OPERATION, REAR WINDOW
DEFOGGER..........................8G-5
GRID REPAIR - STANDARD PROCEDURE,
REAR GLASS HEATING.................8G-4
GRILLE - INSTALLATION..............23-142
GRILLE - INSTALLATION, COWL........23-140
GRILLE - REMOVAL..................23-142
GRILLE - REMOVAL, COWL...........23-140
GRILLE OPENING REINFORCEMENT -
INSTALLATION......................23-142
GRILLE OPENING REINFORCEMENT -
REMOVAL.........................23-142
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO..............................8W-01-9
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-9
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-11
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION.................8A-10
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION.................8A-10
GROUNDS - DESCRIPTION, POWER......8E-13
GUARD - DESCRIPTION, THERMAL......8F-20
GUARD - INSTALLATION, THERMAL......8F-20
GUARD - OPERATION, THERMAL........8F-20
GUARD - REMOVAL, THERMAL..........8F-20
GUIDE ASSEMBLY - INSTALLATION.....23-179
GUIDE ASSEMBLY - REMOVAL.........23-179
GUIDE SEALS - DESCRIPTION, VALVE . 9-29,9-38
GUIDES - DESCRIPTION, VALVE......9-19,9-30
HALF SHAFT - CAUTION................3-10
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-10
HALF SHAFT - INSTALLATION............3-11
HALF SHAFT - REMOVAL...............3-10
HALF SHAFT, SPECIFICATIONS...........3-11
HANDLE - INSTALLATION, A-PILLAR
TRIM AND GRAB....................23-156
HANDLE - INSTALLATION, ASSIST......23-157
HANDLE - INSTALLATION, EXTERIOR . . . 23-123,
23-130,23-136
HANDLE - INSTALLATION, LATCH
RELEASE..........................23-120
HANDLE - REMOVAL, A-PILLAR TRIM
AND GRAB.........................23-156
HANDLE - REMOVAL, ASSIST..........23-157
HANDLE - REMOVAL, EXTERIOR . 23-123,23-130,
23-136
HANDLE - REMOVAL, LATCH RELEASE . . 23-120
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-7
HAZARD SWITCH - DESCRIPTION
.......8L-29
HAZARD SWITCH - INSTALLATION
.......8L-30
HAZARD SWITCH - OPERATION
.........8L-29
HAZARD SWITCH - REMOVAL
..........8L-30
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION
........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION
........................5-36
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION
..........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL
...........................5-36
HEAD - DESCRIPTION, CYLINDER
........9-30
HEAD COVER(S) - DESCRIPTION,
CYLINDER
...........................9-25
HEAD COVER(S) - INSTALLATION,
CYLINDER
.......................9-26,9-34
HEAD COVER(S) - REMOVAL, CYLINDER
. . 9-25,
9-34
KJINDEX 11
Description Group-Page Description Group-Page Description Group-Page

OPERATION - DESCRIPTION, MODES OF . . 8E-11
OPERATION - DIAGNOSIS AND TESTING,
AIR CHECKING TRANSMISSION
CLUTCH............................21-80
ORDER, 2.4L 4-CYLINDER - ENGINE
FIRING..............................8I-2
ORDER, 3.7L V-6 - ENGINE FIRING........8I-2
ORIFICE TUBE - DESCRIPTION, A/C......24-50
ORIFICE TUBE - INSTALLATION, A/C......24-50
ORIFICE TUBE - OPERATION, A/C........24-50
ORIFICE TUBE - REMOVAL, A/C.........24-50
ORVR - DESCRIPTION.................25-29
ORVR - OPERATION..................25-29
OUT - ADJUSTMENT, LOCK..............5-30
OUTBOARD SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-34
OUTBOARD SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-33
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-186
OUTER BELT MOLDING - INSTALLATION,
REAR DOOR.......................23-186
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-186
OUTER BELT MOLDING - REMOVAL,
REAR DOOR.......................23-186
OUTER TIE ROD END REMOVAL TOOL,
SPECIAL TOOLS.....................19-15
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-11
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER.........................8W-97-11
OUTLET - INSTALLATION, POWER....8W-97-13
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER......8W-97-11
OUTLET - REMOVAL, POWER........8W-97-12
OUTLET BARRELS - INSTALLATION,
PANEL.............................24-29
OUTLET BARRELS - REMOVAL, PANEL . . . 24-29
OUTLETS - DESCRIPTION, DEMISTER....24-29
OUTPUT - DESCRIPTION, PCM...........8I-4
OUTPUT - OPERATION, PCM............14-33
OUTPUT - OPERATION, PCM.............8I-4
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - INSTALLATION,
REAR.............................21-212
OUTPUT SHAFT SEAL - REMOVAL,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - REMOVAL, REAR . 21-210
OUTPUT SPEED SENSOR - DESCRIPTION . 21-152
OUTPUT SPEED SENSOR -
INSTALLATION......................21-152
OUTPUT SPEED SENSOR - OPERATION . . 21-152
OUTPUT SPEED SENSOR - REMOVAL . . . 21-152
OVERDRIVE OFF INDICATOR -
DESCRIPTION.......................8J-26
OVERDRIVE OFF INDICATOR -
OPERATION.........................8J-26
OVERDRIVE SWITCH - DESCRIPTION....21-153
OVERDRIVE SWITCH - OPERATION.....21-153
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE, REMOVAL........8M-4
OVERRIDE RELAY - DESCRIPTION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - INSTALLATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - OPERATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - REMOVAL, CLUTCH
SWITCH.............................6-10
OXYGEN SENSOR - DESCRIPTION.......14-40
OXYGEN SENSOR - INSTALLATION.......14-43
OXYGEN SENSOR - OPERATION.........14-40
OXYGEN SENSOR - REMOVAL..........14-41
PADS - INSTALLATION, FRONT BRAKE.....5-11
PADS - REMOVAL, FRONT BRAKE........5-11
PAINT CODE - DESCRIPTION..........23-162
PAINT CODES - SPECIFICATIONS.......23-162
PAINT TOUCH-UP - DESCRIPTION
......23-163
PAN - CLEANING, OIL
..................9-63
PAN - DESCRIPTION, OIL
...............9-63
PAN - INSPECTION, OIL
................9-63
PAN - INSTALLATION, OIL
...............9-64PAN - REMOVAL, OIL..................9-63
PANEL - DESCRIPTION, LATCH - ACCESS . 23-139
PANEL - INSTALLATION, GLASS........23-178
PANEL - INSTALLATION, LATCH -
ACCESS...........................23-139
PANEL - INSTALLATION, QUARTER TRIM . 23-159
PANEL - INSTALLATION, TRIM . . . 23-126,23-132,
23-138
PANEL - REMOVAL, GLASS............23-178
PANEL - REMOVAL, LATCH - ACCESS . . . 23-139
PANEL - REMOVAL, QUARTER TRIM....23-159
PANEL - REMOVAL, TRIM . 23-125,23-132,23-138
PANEL ADJUSTMENT, ADJUSTMENTS -
SUNROOF GLASS...................23-178
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-8
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT......................23-151
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT......................23-149
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT......................23-154
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT......................23-154
PANEL DOOR - INSTALLATION..........24-36
PANEL DOOR ACTUATOR -
INSTALLATION.......................24-25
PANEL DOOR ACTUATOR - REMOVAL....24-24
PANEL DRIVER SIDE BEZELS -
INSTALLATION, INSTRUMENT..........23-154
PANEL DRIVER SIDE BEZELS -
REMOVAL, INSTRUMENT.............23-153
PANEL END CAP - INSTALLATION,
INSTRUMENT......................23-153
PANEL END CAP - REMOVAL,
INSTRUMENT......................23-153
PANEL OUTLET BARRELS -
INSTALLATION.......................24-29
PANEL OUTLET BARRELS - REMOVAL....24-29
PANEL PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT..........23-154
PANEL PASSENGER SIDE BEZEL -
REMOVAL, INSTRUMENT.............23-154
PANEL SEAL - INSTALLATION, GLASS . . . 23-178
PANEL SEAL - REMOVAL, GLASS.......23-178
PANEL TOP COVER - INSTALLATION,
INSTRUMENT......................23-153
PANEL TOP COVER - REMOVAL,
INSTRUMENT......................23-152
PARK - INTERLOCK CABLE -
INSTALLATION......................21-153
PARK - INTERLOCK CABLE - REMOVAL . . 21-153
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PARK RAMP - INSTALLATION, WIPER
ARM ..............................8R-43
PARK RAMP - REMOVAL, WIPER ARM . . . 8R-43
PARKING BRAKE - DESCRIPTION.........5-29
PARKING BRAKE - OPERATION...........5-29
PARK-INTERLOCK CABLE -
ADJUSTMENTS.....................21-154
PART TIME INDICATOR - DESCRIPTION . . . 8J-29
PART TIME INDICATOR - OPERATION.....8J-29
PASSENGER AIRBAG - DESCRIPTION....8O-27
PASSENGER AIRBAG - INSTALLATION....8O-29
PASSENGER AIRBAG - OPERATION......8O-27
PASSENGER AIRBAG - REMOVAL........8O-28
PASSENGER AIRBAG DOOR -
INSTALLATION......................8O-30
PASSENGER AIRBAG DOOR - REMOVAL . . 8O-29
PASSENGER AIRBAG MOUNTING
BRACKET - INSTALLATION.............8O-31
PASSENGER AIRBAG MOUNTING
BRACKET - REMOVAL
.................8O-31
PASSENGER SEAT HEATER SWITCH -
DESCRIPTION
.......................8G-14
PASSENGER SEAT HEATER SWITCH -
INSTALLATION
......................8G-15
PASSENGER SEAT HEATER SWITCH -
OPERATION
.........................8G-14
PASSENGER SEAT HEATER SWITCH -
REMOVAL
..........................8G-15PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT PANEL....23-154
PASSENGER SIDE BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION..................8E-11
PCM - OPERATION...................8E-14
PCM INPUT - OPERATION, ASD SENSE.....8I-4
PCM OUTPUT - DESCRIPTION............8I-4
PCM OUTPUT - OPERATION............14-33
PCM OUTPUT - OPERATION.............8I-4
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE.........................8E-1
PCV VALVE - DESCRIPTION............25-29
PCV VALVE - DIAGNOSIS AND TESTING . . . 25-31
PCV VALVE - INSTALLATION............25-32
PCV VALVE - OPERATION..............25-31
PCV VALVE - REMOVAL...............25-32
PEDAL - DESCRIPTION.................5-20
PEDAL - INSTALLATION................5-20
PEDAL - INSTALLATION, ACCELERATOR . . . 14-30
PEDAL - INSTALLATION, CLUTCH.........6-10
PEDAL - OPERATION...................5-20
PEDAL - REMOVAL....................5-20
PEDAL - REMOVAL, ACCELERATOR......14-29
PEDAL - REMOVAL, CLUTCH............6-10
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-11
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-11
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-11
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION..........6-8
PILOT BEARING - REMOVAL..............6-8
PINION GEAR/RING GEAR -
INSTALLATION........................3-46
PINION GEAR/RING GEAR - REMOVAL.....3-44
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION...................3-112,3-82
PINION GEAR/RING GEAR/TONE RING -
REMOVAL......................3-110,3-79
PINION SEAL - INSTALLATION . . 3-103,3-39,3-68
PINION SEAL - REMOVAL......3-102,3-38,3-68
PIPE - INSTALLATION, CROSS-OVER......11-3
PIPE - REMOVAL, CROSS-OVER..........11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-49
PISTON FITTING - STANDARD
PROCEDURE.........................9-50
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-52
PISTONS - DESCRIPTION.............21-155
PISTONS - OPERATION...............21-155
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-160
PLANETARY GEARTRAIN - CLEANING....21-159
PLANETARY GEARTRAIN - DESCRIPTION . 21-157
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-159
PLANETARY GEARTRAIN - INSPECTION . . 21-159
PLANETARY GEARTRAIN - OPERATION . . 21-157
PLATE - INSTALLATION, DOOR SILL
SCUFF............................23-157
PLATE - INSTALLATION, FLEX............9-49
PLATE - INSTALLATION, FRONT SKID......13-6
PLATE - INSTALLATION, FUEL TANK
SKID...............................13-9
PLATE - INSTALLATION, REAR DOOR
SCUFF............................23-160
PLATE - INSTALLATION, TRANSFER
CASE SKID..........................13-7
PLATE - REMOVAL, DOOR SILL SCUFF . . . 23-157
PLATE - REMOVAL, FLEX...............9-49
PLATE - REMOVAL, FRONT SKID.........13-6
PLATE - REMOVAL, FUEL TANK SKID
......13-9
PLATE - REMOVAL, REAR DOOR SCUFF
. . 23-160
PLATE - REMOVAL, TRANSFER CASE
SKID
...............................13-7
PLATE LAMP BULB - INSTALLATION,
LICENSE
...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE
...........................8L-44
18 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

SPARK PLUG - OPERATION.............8I-12
SPARK PLUG - REMOVAL..............8I-15
SPARK PLUG CABLE RESISTANCE, 2.4L....8I-3
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-13
SPARK PLUGS, SPARK PLUG -
CLEANING..........................8I-15
SPARK PLUGS, SPECIFICATIONS..........8I-3
SPEAKER - DESCRIPTION..............8A-13
SPEAKER - INSTALLATION.............8A-15
SPEAKER - OPERATION...............8A-14
SPEAKER - REMOVAL.................8A-14
SPECIAL TOOLS - 3.7L ENGINE..........9-15
SPECIAL TOOLS - 8 1/4 AXLE...........3-98
SPECIAL TOOLS - BASE BRAKES..........5-7
SPECIAL TOOLS - BODY................23-5
SPECIAL TOOLS - COOLING.............7-14
SPECIAL TOOLS - FRONT AXLE..........3-34
SPECIAL TOOLS - FRONT SUSPENSION.....2-8
SPECIAL TOOLS - FUEL SYSTEM.........14-6
SPECIAL TOOLS - OUTER TIE ROD END
REMOVAL TOOL.....................19-15
SPECIAL TOOLS - POWER
DISTRIBUTION SYSTEMS............8W-97-2
SPECIAL TOOLS - POWER STEERING
PUMP.............................19-20
SPECIAL TOOLS - REAR AXLE...........3-63
SPECIAL TOOLS - RFE TRANSMISSION....21-120
SPECIAL TOOLS - STEERING COLUMN....19-8
SPECIAL TOOLS - WIRING/TERMINAL . 8W-01-10
SPECIAL TOOLS, BATTERY SYSTEM.......8F-7
SPECIFICATIONS, BATTERY SYSTEM......8F-6
SPECIFICATIONS, BRAKES - ABS.........5-33
SPECIFICATIONS, CHARGE CAPACITY.....24-42
SPECIFICATIONS, CLUTCH...............6-5
SPECIFICATIONS, DIAGNOSIS AND
TESTING............................22-8
SPECIFICATIONS, FLUID CAPACITIES.......0-4
SPECIFICATIONS, FRAME DIMENSIONS....13-3
SPECIFICATIONS, FRONT AXLE...........3-33
SPECIFICATIONS, GAP AND FLUSH.....23-116
SPECIFICATIONS, IGNITION TIMING.......8I-2
SPECIFICATIONS, LAMPS/LIGHTING -
EXTERIOR..........................8L-15
SPECIFICATIONS, LAMPS/LIGHTING -
INTERIOR..........................8L-71
SPECIFICATIONS, NV1500..............21-30
SPECIFICATIONS, OPENING DIMENSIONS . 23-111
SPECIFICATIONS, PAINT CODES........23-162
SPECIFICATIONS, REAR AXLE............3-62
SPECIFICATIONS, REMOTE KEYLESS
ENTRY TRANSMITTER.................8N-9
SPECIFICATIONS, SEALER LOCATIONS....23-87
SPECIFICATIONS, SPECIFICATIONS.......24-10
SPECIFICATIONS, STANDARD
PROCEDURE.........................23-4
SPECIFICATIONS, TORQUE..............13-6
SPECIFICATIONS, WELD AND
STRUCTURAL ADHESIVE LOCATIONS......23-9
SPEED CONTROL - DESCRIPTION........8P-1
SPEED CONTROL - OPERATION..........8P-1
SPEED CONTROL - TORQUE.............8P-2
SPEED SENSOR - DESCRIPTION, INPUT . 21-143
SPEED SENSOR - DESCRIPTION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, FRONT
WHEEL.............................5-34
SPEED SENSOR - INSTALLATION, INPUT . 21-143
SPEED SENSOR - INSTALLATION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, REAR
WHEEL.............................5-35
SPEED SENSOR - OPERATION, INPUT . . . 21-143
SPEED SENSOR - OPERATION, OUTPUT . . 21-152
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-34
SPEED SENSOR - REMOVAL, INPUT.....21-143
SPEED SENSOR - REMOVAL, OUTPUT . . . 21-152
SPEED SENSOR - REMOVAL, REAR
WHEEL.............................5-35
SPEEDOMETER - DESCRIPTION
.........8J-32
SPEEDOMETER - OPERATION
...........8J-32
SPLASH SHIELD - INSTALLATION,
FRONT WHEELHOUSE
................23-143
SPLASH SHIELD - INSTALLATION, REAR
WHEELHOUSE
......................23-144
SPLASH SHIELD - REMOVAL, FRONT
WHEELHOUSE
......................23-143SPLASH SHIELD - REMOVAL, REAR
WHEELHOUSE......................23-144
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-7
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-14
SPRING - INSTALLATION...........2-13,2-18
SPRING - REMOVAL...............2-13,2-18
SPRINGS - DESCRIPTION, VALVE.....9-29,9-38
SPRINGS - INSTALLATION, VALVE....9-29,9-38
SPRINGS - REMOVAL, VALVE........9-29,9-38
STABILIZER BAR - INSTALLATION....2-14,2-19
STABILIZER BAR - REMOVAL........2-14,2-19
STABILIZER BAR BUSHINGS -
INSTALLATION.........................2-9
STABILIZER BAR BUSHINGS - REMOVAL....2-9
STABILIZER LINK - INSTALLATION........2-14
STABILIZER LINK - REMOVAL............2-14
STAKING - STANDARD PROCEDURE,
HEAT ...............................23-3
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-39
STARTER MOTOR - INSTALLATION.......8F-41
STARTER MOTOR - REMOVAL..........8F-39
STARTER MOTOR, GAS POWERED.......8F-39
STARTER MOTOR RELAY - DESCRIPTION . 8F-41
STARTER MOTOR RELAY -
INSTALLATION.......................8F-43
STARTER MOTOR RELAY - OPERATION.....8F-42
STARTER MOTOR RELAY - REMOVAL.....8F-43
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-42
STARTING PROCEDURE - STANDARD
PROCEDURE, JUMP....................0-5
STARTING SYSTEM - DESCRIPTION......8F-32
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-33
STARTING SYSTEM - INSPECTION.......8F-37
STARTING SYSTEM - OPERATION........8F-32
STATE DISPLAY TEST MODE -
DESCRIPTION........................25-2
STEERING - DESCRIPTION..............19-1
STEERING - OPERATION................19-1
STEERING COLUMN, SPECIAL TOOLS.....19-8
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER.......19-3
STEERING LINKAGE - STANDARD
PROCEDURE........................19-16
STEERING PRESSURE SWITCH -
DESCRIPTION, POWER................19-22
STEERING PRESSURE SWITCH -
INSTALLATION, POWER...............19-22
STEERING PRESSURE SWITCH -
OPERATION, POWER..................19-22
STEERING PRESSURE SWITCH -
REMOVAL, POWER...................19-22
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-18
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-20
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-1
STEERING SYSTEM - DIAGNOSIS AND
TESTING, SUSPENSION.................2-1
STEERING WHEEL - INSTALLATION......19-12
STEERING WHEEL - REMOVAL..........19-12
STOP LAMP BULB - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP BULB - REMOVAL, CENTER
HIGH MOUNTED.....................8L-18
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-19
STRAP - DESCRIPTION, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRAP - INSTALLATION, CHECK . 23-121,23-128,
23-135
STRAP - INSTALLATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-11
STRAP - OPERATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRAP - REMOVAL, CHECK
.....23-121,23-128,
23-135
STRAP - REMOVAL, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRIKER - INSTALLATION, GLOVE BOX
LATCH
............................23-149STRIKER - INSTALLATION, HOOD AJAR
SWITCH............................8Q-14
STRIKER - INSTALLATION, LATCH......23-124,
23-132,23-137
STRIKER - INSTALLATION, REAR SEAT
BACK LATCH.......................23-171
STRIKER - REMOVAL, GLOVE BOX
LATCH ............................23-148
STRIKER - REMOVAL, HOOD AJAR
SWITCH............................8Q-13
STRIKER - REMOVAL, LATCH . . . 23-124,23-132,
23-137
STRIKER - REMOVAL, REAR SEAT BACK
LATCH ............................23-170
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS, WELD................23-9
STRUCTURAL COVER - DESCRIPTION.....9-55
STRUCTURAL COVER - INSTALLATION.....9-55
STRUCTURAL COVER - OPERATION.......9-55
STRUCTURAL COVER - REMOVAL........9-55
STUDS - INSTALLATION...............22-11
STUDS - REMOVAL...................22-11
SUCTION LINE - INSTALLATION, A/C.....24-49
SUCTION LINE - REMOVAL, A/C.........24-48
SUN VISOR - INSTALLATION..........23-160
SUN VISOR - REMOVAL..............23-160
SUN VISOR SUPPORT - INSTALLATION . . 23-160
SUN VISOR SUPPORT - REMOVAL......23-160
SUNROOF - DESCRIPTION............23-175
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-178
SUNSHADE - INSTALLATION...........23-179
SUNSHADE - REMOVAL..............23-179
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A.........8O-6
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING..............8O-6
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLIES - DESCRIPTION, 5 VOLT......8E-13
SUPPLIES - OPERATION, 5 VOLT........8E-15
SUPPORT - INSTALLATION, REAR
FASCIA..............................13-3
SUPPORT - INSTALLATION, SUN VISOR . . 23-160
SUPPORT - REMOVAL, REAR FASCIA......13-3
SUPPORT - REMOVAL, SUN VISOR.....23-160
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR.................23-161
SUPPORT CYLINDER - INSTALLATION . . . 23-120
SUPPORT CYLINDER - INSTALLATION,
FLIP-UP GLASS.....................23-139
SUPPORT CYLINDER - REMOVAL.......23-120
SUPPORT CYLINDER - REMOVAL,
FLIP-UP GLASS.....................23-139
SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO NOISE............8A-9
SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO NOISE...........8A-11
SUPPRESSION GROUND STRAP -
OPERATION, RADIO NOISE.............8A-10
SUPPRESSION GROUND STRAP -
REMOVAL, RADIO NOISE..............8A-10
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET............9-9
SUSPENSION - DIAGNOSIS AND
TESTING, REAR.......................2-17
SUSPENSION AND STEERING SYSTEM -
DIAGNOSIS AND TESTING...............2-1
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - DESCRIPTION, UPPER......2-20
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - OPERATION, UPPER........2-20
SUSPENSION, SPECIAL TOOLS - FRONT....2-8
SWING GATE - INSTALLATION.........23-138
SWING GATE - REMOVAL.............23-138
SWING GATE BELTLINE WEATHERSTRIP
- INSTALLATION....................23-186
SWING GATE BELTLINE WEATHERSTRIP
- REMOVAL
........................23-186
SWING GATE OPENING WEATHERSTRIP
- INSTALLATION
....................23-186
SWING GATE OPENING WEATHERSTRIP
- REMOVAL
........................23-186
SWITCH - DESCRIPTION
................8P-5
SWITCH - DESCRIPTION, A/C HIGH
PRESSURE
.........................24-17
KJINDEX 25
Description Group-Page Description Group-Page Description Group-Page

JEEP LIBERTY 2002
4'M"anuaIWindows R 55360036AA #.3 66.70L 55360027AA #.3 66.70#WlDoor Glass RemovedPower Windows1! R 55360034AA #.3 46.35L 55360035AA #.3 46.351]Additional Paris &/or Dealer Col'ltact RequiredMotor, Window Ail N.A #.3 0.00#R&R One Side Complete, w/D'~or Glass RemovedHandle, Window R/L FW80WI_5 6.95
~5
~
REAR DOOR Cont'd
Refinish UpperHinge-~~ .Refinish Lower Hinge R&I Outside Handle Assy #/ncludes R&I Trim PanelR/L .3R/L .3AiL #.5
2
1
11
..PUse Procedure Explanations 17 and 28 with the following tex/.3004-09564~
SHEET METAL121 Console, Overheadw/Sunroofw/o SunroofModule, Consolew/Garage Door Opener2 Lamp, Consolew/Sunroof Switchw/o Sunroof Switch3 Lens, LampI 4 Wiring Console5 Bulb, 'Console (2)Switch, SunroofSwitch, Reading Lamp
WA951L2AA5O14271AA
4760145BF
WA901L2AAPB83TL2AB55196755AA4760644LOOOO1925GM78TL2AA4685445
.4 00.45.4 189.00
315.00
.3 66.35.3 78.20.1 6.50.3 20.85.1 1.9575.105.00
3.5
1.0~7
e-d r
10~
9-d
Refinish RoofOulside Add 10 R&R Roof Panel
To Drill for & Install Luggage Rack5
~12 3
~"
3
ROOF LUGGAGE RACK
4004-09561R&I Luggage RackAssy .5R&R Luggage Rack Complete (Includes R&I) 8
NOTE: All Parts in this section are included in R&R LuggageRack Complete unless noted otherwise.
#.3 5O.35l#.3 45:75-#.3 81.75 1 Panel Roof#.3 81.75 w/Sunroof 55176995AB #16.5 215.00.2 875 wlo Sunroof 55176994AB #15.5 155.002.75 #Does Not Inc/l~de R&R Quslter Glass2'95 2 Panel, Front Header 55177022AA 1.0 22.952.95 3 Bow, No.1 Roof15.70 wlo Sunroof 553602E:1AA 1.0 18.102:85 4 Bow, No.2 Roof 5517699:~AA 1.0 18.101AA 1.0 18.102.8510.00 EXTERIOR TRIM~
I ~-
T ~;:../ 4~~b -8 11--dJ'~~:;;f~~::::::=~- 3 6
12 '
004-09559
1 Latch, DoorManual Locks R 55177046ABL 55177047ABPower Locks R 55177044ABL 55177045AB#Wrrrim Panel Removed2 Striker, Latch AiL 4780607AA3 Spacer, Striker AiL 45202894 Rod, Inside Lock R 5072360AAL 5O72361AACover, Latch AiL 5014395AA5 Rod, Inside Handle R 5072356AAL 5072357AA6 Rod, Lock Knob R 55360464AAL 55360465AA7 Handle, Outside R 55360334AB #.2 36.00 IL 55360335AB #.2 36.00#Wrrrim Panel Removed8 Hinge, Upper AiL 55177030AA #.2 26.259 Hinge, Lower AiL 55177030AA #.2 26.25#W/Door & Upper Center Trim Panel Removed10 Check, Door AiL 55177036AB #.2 26.50#Wrrrim Panel Removed11 Seal, Lower Door AiL 55235930AA .2 9.0012 Weatherstrip, Door1] AiL 5GU15WL5AA .6 57.201]Addilional Paris &/or Dealer Contact Required
"--"~~~~-~,'" -~$ --.""",," _,,;-r-:>"'-~,,--'"~~ -s:",,- -~-'"",," 6"",-""~-/-. '- /,'--=, I'
1
'"'.."
.4 90.25
13.1013.1012.4512.45
#.3 59.50#.3 59.50
0.000.00
0.000.00
.8 409.00
#.3 59.50
#.3 59.50
GLASS & PARTS1 Moulding, Roofw/Roof~ack
wiD Roof Rack
.5.5.5.5
54.2054.2066.20166.20
1-{12
R 553601i'4AAL 553601i'5AAR 553601i'6AAL 553601i7AA
9
p
R&I Headliner.2.8v
,~,17=~'7~
t'...'"004-09932 ""',Ii;-
1 Rail, Luggage Rack AIL 55360419ABCover, luggage RackFront R 55360424AAL 55360425AA3 Rear R 55360426AAIL 55360427AA4 Rail, Luggage Rack CrossFront 55360526AARear 55156586AA#R&R Both .4I 5 Cap, Screw Cover (2iSidelAIL 55156591AA6 Cap, Cross Rail End (2JSide Ail 55156597AA7 Cover, Cross RailFront SJA18ZSPAARear SJA19ZSPAA8 Carrier Assy, CargoRenegade Model 5HZ66ZSPAB9 Rail, Front Cross~Renegade Model 55360526AB10 Rail, Rear Cross1\Renegade Model 55156586AB~fncfuded w/Cargo Carrier Assy#R&R Both.411 Isolator, Cargo Carrierw/Sunroof
WiD Sunroof
3
2, ,
~
6
R 55156592ABL 55156593ABR 55156594ABL 55156595AB
9.709.709.709.70.J/004-09563
LIGHT BAR004-09930
1 Glass, Rear DoorChrysler-Tinted R 55360378ABL 55360379ABNAGSGreen R/L DDO9986-7GTYPrivacy R/L DD10064-3YPY2 Glass/Channel, GlassChrysler-TintedGreen R 55235876ABL 55235877ABPrivacy R 55360172ABL 55360173ABNAGSGreen R/L DVO9993-4GTNPrivacy R/L DV10Q65-6YPY#W/Door Glass Removed3 Weatherstrip, Frt Pillar R/L 55235860AA4 Weatherstrip, Outer Belt R 55235872AAL 55235873AA5 Weatherstrip, Inner Belt R 55235886ABL 55235887AB
1.0 195.001.0 210.00
1.0 403.651.0 411.85
2
3~45
~~6
004-09933
1 Cover, Light Bar2 lamPILight Bar (4)3 Bulb 4l4 Cover, ens5 Bar, Support6 Harness, Light Bar
5HZO1ZSPAB52112063ABLOOO90065HZO7RXFAB5083967 AA52112062AA
1 Headliner1l Iw/Sunroolw/Side Air Bag OY911 L2AA 2.8 627.00'wlo Side Air Bag UY731L2AA 2.8 800.00wlo Sunroofw/Side Air Bag UY87TL2AA 2.8 627.00wlo Side Air Bag' UY71TL2AA 2.8 735.001]Additional Parts &/or Dealer Contact Required2 Handle, Grab R UY681L2AA .1 0.00L UY691L2AA .1 0.00#.3 139.00'Lamp, Cargo 5FT10TL2 43.50#.3 139.00 Lens, ~argo Lamp. 55196755AA 6.50#.3 145.00 Moulding, Rear Intenor#.3 145.00 Slate Gray 5GP80WL5AC 11.50Taupe 5GP80XDVAC 11.50#.3 0.00 Clip, Mldg Retainer (!9) 6506311 AA .45#.3 737.10
.2 13.95.2 24.751R&I Overhead Console .2.2 24.7520.25 NOTE: All Parts in this section are included in R&R Overhead20.25 Console unless noted otherwise.
Labor Times Shown are for Replacement with New OEM Undamaged Parts on New Undamaged Vehicles.Comments or suggestions? Need assistance? Call 1-800-854-7030 or 8581578-6550, Ext 8220. Fax 1-888-256-7969 or 8581549-0629.574
165.00143.0010.000.00160.0040.35
2,