2002 JEEP LIBERTY Timing cover gasket

INSPECTION
(1) Inspect camshaft bearing journals for damage
and binding (Fig. 19). If journals are binding, check
the cylinder head for damage. Also check cylinder
head oil holes for clogging.
(2) Check the cam lobe and bearing surfaces for
abnormal wear and damage. Replace camshaft if
defective.
NOTE: If camshaft is replaced due to lobe wear or
damage, always replace the rocker arms.
(3) Measure the lobe actual wear (unworn area -
wear zone = actual wear) (Fig. 19) and replace cam-
shaft if out of limit. Standard value is 0.0254 mm
(0.001 in.), wearlimitis 0.254 mm (0.010 in.).
INSTALLATION
CAUTION: Ensure that NONE of the pistons are at
top dead center when installing the camshafts.
(1) Lubricate all camshaft bearing journals, rocker
arms and camshaft lobes.
(2) Install all rocker arms in original positions, if
reused.
(3) Position camshafts on cylinder head bearing
journals. Install right and left camshaft bearing caps
No.2±5andright No. 6. Tighten M6 fasteners to 12
N´m (105 in. lbs.) in sequence shown in (Fig. 20).
(4) Apply MopartGasket Maker to No. 1 and No.
6 bearing caps (Fig. 21). Install bearing caps and
tighten M8 fasteners to 28 N´m (250 in. lbs.).NOTE: Bearing end caps must be installed before
seals can be installed.
(5) Install camshaft oil seals. (Refer to 9 -
ENGINE/CYLINDER HEAD/CAMSHAFT OIL
SEAL(S) - INSTALLATION)
(6) Install camshaft target magnet and camshaft
position sensor.
(7) Install cylinder head cover. (Refer to 9 -
ENGINE/CYLINDER HEAD/CYLINDER HEAD
COVER(S) - INSTALLATION)
(8) Install timing belt rear cover and camshaft
sprocket. (Refer to 9 - ENGINE/VALVE TIMING/
TIMING BELT / CHAIN COVER(S) - INSTALLA-
TION)
(9) Install timing belt. (Refer to 9 - ENGINE/
VALVE TIMING/TIMING BELT/CHAIN AND
SPROCKETS - INSTALLATION)
Fig. 19 Checking Camshaft(s) for Wear
1 - UNWORN AREA
2 - ACTUAL WEAR
3 - BEARING JOURNAL
4 - LOBE
5 - WEAR ZONE
Fig. 20 Camshaft Bearing Cap Tightening Sequence
Fig. 21 Camshaft Bearing Cap Sealing
1 - 1.5 mm (.060 in.) DIAMETER BEAD OF MOPAR GASKET
MAKER
KJENGINE9s-25
CAMSHAFT(S) (Continued)

CYLINDER HEAD COVER
REMOVAL
(1) Remove intake manifold. (Refer to 9 -
ENGINE/MANIFOLDS/INTAKE MANIFOLD -
REMOVAL)
(2) Remove ignition coil and spark plug wires.
(3) Disconnect PCV and make-up air hoses from
cylinder head cover.
(4) Remove cylinder head cover bolts.
(5) Remove cylinder head cover from cylinder
head.
CLEANING
Clean cylinder head and cover mating surfaces
using a suitable solvent.
INSPECTION
Inspect cover rails for flatness.
INSTALLATION
NOTE: Replace spark plug well seals and bolt
assemblies when installing a new cylinder head
cover gasket.
(1) Install new cylinder head cover gaskets and
spark plug well seals (Fig. 22).
(2) Replace cylinder head cover bolt assemblies
(Fig. 23).
CAUTION: Do not allow oil or solvents to contact
the timing belt as they can deteriorate the rubber
and cause tooth skipping.(3) Apply MopartEngine RTV GEN II at the
camshaft cap corners and at the top edges of the 1/2
round seal (Fig. 24).
Fig. 22 Spark Plug Well Seals
Fig. 23 Cylinder Head Cover Bolt Assembly
Fig. 24 Sealer Locations - Typical
1 ± SEALER LOCATION
9s - 26 ENGINEKJ

instrument panel on either a CCD or PCI bus circuit
(depending on vehicle line) to operate the oil pressure
gauge and the check gauges lamp. Ground for the
sensor is provided by the PCM through a low-noise
sensor return.
OIL PUMP
REMOVAL
(1) Disconnect negative cable from battery.
(2) Remove timing belt. (Refer to 9 - ENGINE/
VALVE TIMING/TIMING BELT/CHAIN AND
SPROCKETS - REMOVAL)
(3) Remove timing belt rear cover. (Refer to 9 -
ENGINE/VALVE TIMING/TIMING BELT / CHAIN
COVER(S) - REMOVAL)
(4) Remove oil pan. (Refer to 9 - ENGINE/LUBRI-
CATION/OIL PAN - REMOVAL)
(5) Remove crankshaft sprocket using Special
Tools 6793 and C-4685-C2 (Fig. 81).
(6) Remove crankshaft key (Fig. 82).
(7) Remove oil pick-up tube.
(8) Remove oil pump (Fig. 83) and front crankshaft
seal.
DISASSEMBLY
(1) To remove the relief valve, proceed as follows:
(a) Remove the threaded plug and gasket from
the oil pump.
(b) Remove spring and relief valve.
(2) Remove oil pump cover fasteners, and lift off
cover.
(3) Remove pump rotors.
(4) Wash all parts in a suitable solvent and
inspect carefully for damage or wear.
CLEANING
(1) Clean all parts thoroughly in a suitable sol-
vent.
Fig. 81 Crankshaft Sprocket - Removal
1 - SPECIAL TOOL 6793
2 - SPECIAL TOOL C-4685±C2
3 - CRANKSHAFT SPROCKET
Fig. 82 Crankshaft Key
1 - CRANKSHAFT KEY
Fig. 83 2.4L OIL PUMP
1 - BOLTS
2 - BOLTS
KJENGINE9s-49
OIL PRESSURE SENSOR/SWITCH (Continued)

INSPECTION
(1) Inspect the mating surface of the oil pump.
Surface should be smooth. Replace pump cover if
scratched or grooved.
(2) Lay a straightedge across the pump cover sur-
face (Fig. 84). If a 0.025 mm (0.001 in.) feeler gauge
can be inserted between cover and straight edge,
cover should be replaced.
(3) Measure thickness and diameter of outer rotor.
If outer rotor thickness measures 9.40 mm (0.370 in.)
or less (Fig. 85), or if the diameter is 79.95 mm
(3.148 in.) or less, replace outer rotor.
(4) If inner rotor measures 9.40 mm (0.370 in.) or
less replace inner rotor (Fig. 86).
ASSEMBLY
(1) Assemble pump, using new parts as required.
Install the inner rotor with chamfer facing the
cast iron oil pump cover.
(2) Prime oil pump before installation by filling
rotor cavity with engine oil.
(3) Install cover and tighten fasteners to 12 N´m
(105 in. lbs.).
CAUTION: Oil pump pressure relief valve must be
installed correctly or serious engine damage may
occur.
(4) Install relief valve, spring, gasket and cap.
Tighten cap to 41 N´m (30 ft. lbs.).
INSTALLATION
(1) Make sure all surfaces are clean and free of oil
and dirt.
(2) Apply MopartGasket Maker to oil pump as
shown in (Fig. 87). Install O-ring into oil pump body
discharge passage.
(3) Prime oil pump with engine oil before installa-
tion.
(4) Align oil pump rotor flats with flats on crank-
shaft. Install the oil pump to the block.
CAUTION: To align, the front crankshaft seal MUST
be out of pump, or damage may result.
(5) Install new front crankshaft seal using Special
Tool 6780 (Fig. 88).
(6) Install crankshaft key (Fig. 82).
CAUTION: The crankshaft sprocket is set to a pre-
determined depth from the factory for correct tim-
ing belt tracking. If removed, use of Special Tool
6792 is required to set the sprocket to original
installation depth. An incorrectly installed sprocket
will result in timing belt and engine damage.
Fig. 84 Checking Oil Pump Cover Flatness
1 - STRAIGHT EDGE
2 - FEELER GAUGE
3 - OIL PUMP COVER
Fig. 85 Measuring Outer Rotor Thickness
Fig. 86 Measuring Inner Rotor Thickness
9s - 50 ENGINEKJ
OIL PUMP (Continued)

EXHAUST MANIFOLD
DESCRIPTION
The exhaust manifold is made of Hi-Silicone Moly
nodular cast iron for strength and high tempera-
tures. The manifold attaches to the cylinder head.
OPERATION
The exhaust manifold collects the exhaust gasses
exiting the combustion chambers. Then it channels
the exhaust gasses to the exhaust pipe attached to
the manifold.
REMOVAL
(1) Raise vehicle and disconnect exhaust pipe from
the exhaust manifold.
(2) Lower the vehicle.
(3) Disconnect upstream oxygen sensor connector
at the rear of exhaust manifold.
(4) Remove the air cleaner bracket (Fig. 91).
(5) Remove the heat shield.
(6) Remove the bolts attaching the manifold to the
cylinder head.
(7) Remove exhaust manifold.
(8) Inspect the manifold. (Refer to 9 - ENGINE/
MANIFOLDS/EXHAUST MANIFOLD - INSPEC-
TION)
CLEANING
(1) Discard gasket (if equipped) and clean all sur-
faces of manifold and cylinder head.
INSPECTION
(1) Inspect manifold gasket surfaces for flatness
with straight edge. Surface must be flat within 0.15
mm per 300 mm (0.006 in. per foot) of manifold
length.
(2) Inspect manifolds for cracks or distortion.
Replace manifold as necessary.
INSTALLATION
(1) Clean the manifold mating surfaces.
(2) Install exhaust manifold with a new gasket.
Tighten attaching nuts to 20 N´m (175 in. lbs.).
(3) Attach exhaust pipe to exhaust manifold and
tighten fasteners to 37 N´m (27 ft. lbs.).
(4) Install and connect the oxygen sensor. (Refer to
14 - FUEL SYSTEM/FUEL INJECTION/O2 SENSOR
- COMPONENT LOCATION)
(5) Install the heat shield.
(6) Install the air cleaner bracket.
TIMING BELT COVER(S)
REMOVAL
FRONT COVER
(1) Remove crankshaft vibration damper. (Refer to
9 - ENGINE/ENGINE BLOCK/VIBRATION
DAMPER - REMOVAL)
(2) Remove generator drive belt tensioner assem-
bly. (Refer to 7 - COOLING/ACCESSORY DRIVE/
BELT TENSIONERS - REMOVAL)
(3) Remove timing belt front cover bolts, and
remove covers.
REAR COVER
(1) Remove front covers.
(2) Remove timing belt. (Refer to 9 - ENGINE/
VALVE TIMING/TIMING BELT/CHAIN AND
SPROCKETS - REMOVAL)
(3) Hold camshaft sprocket with Special Tool 6847
while removing center bolt.
(4) Remove timing belt idler pulley.
(5) Remove rear cover fasteners and remove cover
from engine.
INSTALLATION
REAR COVER
(1) Install timing belt rear cover and bolts (Fig.
92). Torque bolts to 12 N´m (105 in. lbs).
Fig. 91 AIR CLEANER BRACKET
1 - AIR CLEANER BRACKET
2 - BOLT (2)
KJENGINE9s-53

COVER - REMOVAL, COWL TRIM.......23-157
COVER - REMOVAL, INSTRUMENT
PANEL TOP........................23-152
COVER - REMOVAL, STRUCTURAL........9-55
COVER(S) - DESCRIPTION, CYLINDER
HEAD...............................9-25
COVER(S) - INSTALLATION, CYLINDER
HEAD...........................9-26,9-34
COVER(S) - INSTALLATION, TIMING
BELT / CHAIN........................9-76
COVER(S) - REMOVAL, CYLINDER HEAD . . 9-25,
9-34
COVER(S) - REMOVAL, TIMING BELT /
CHAIN..............................9-74
COWL GRILLE - INSTALLATION........23-140
COWL GRILLE - REMOVAL............23-140
COWL TRIM COVER - INSTALLATION....23-157
COWL TRIM COVER - REMOVAL.......23-157
COWL WEATHERSTRIP - INSTALLATION . 23-185
COWL WEATHERSTRIP - REMOVAL.....23-185
COWL/PLENUM SEAL - INSTALLATION . . . 23-187
COWL/PLENUM SEAL - REMOVAL......23-187
COWL/PLENUM WINDOW BAFFLE SEAL -
INSTALLATION......................23-187
COWL/PLENUM WINDOW BAFFLE SEAL -
REMOVAL.........................23-187
CRADLE CROSSMEMBER -
INSTALLATION, ENGINE................13-6
CRADLE CROSSMEMBER - REMOVAL,
ENGINE.............................13-6
CRANKSHAFT - DESCRIPTION...........9-42
CRANKSHAFT - INSPECTION.............9-43
CRANKSHAFT - INSTALLATION...........9-43
CRANKSHAFT - REMOVAL..............9-43
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........................9-47
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL...........................9-46
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........................9-48
CRANKSHAFT OIL SEAL - REAR -
REMOVAL...........................9-48
CRANKSHAFT POSITION SENSOR -
DESCRIPTION.......................14-30
CRANKSHAFT POSITION SENSOR -
INSTALLATION.......................14-32
CRANKSHAFT POSITION SENSOR -
OPERATION.........................14-31
CRANKSHAFT POSITION SENSOR -
REMOVAL..........................14-31
CROSSMEMBER - INSTALLATION,
ENGINE CRADLE......................13-6
CROSSMEMBER - INSTALLATION,
RADIATOR.........................23-146
CROSSMEMBER - INSTALLATION, REAR . . . 13-7
CROSSMEMBER - REMOVAL, ENGINE
CRADLE.............................13-6
CROSSMEMBER - REMOVAL, RADIATOR . 23-146
CROSSMEMBER - REMOVAL, REAR.......13-7
CROSS-OVER PIPE - INSTALLATION.......11-3
CROSS-OVER PIPE - REMOVAL..........11-3
CRUISE INDICATOR - DESCRIPTION......8J-16
CRUISE INDICATOR - OPERATION.......8J-17
CURTAIN AIRBAG - DESCRIPTION, SIDE . . 8O-38
CURTAIN AIRBAG - INSTALLATION, SIDE . . 8O-41
CURTAIN AIRBAG - OPERATION, SIDE....8O-39
CURTAIN AIRBAG - REMOVAL, SIDE.....8O-40
CUSHION - FRONT - INSTALLATION,
SEAT .............................23-167
CUSHION - FRONT - INSTALLATION,
SEAT BACK........................23-167
CUSHION - FRONT - REMOVAL, SEAT . . . 23-167
CUSHION - FRONT - REMOVAL, SEAT
BACK.............................23-167
CUSHION - REAR - INSTALLATION, SEAT . 23-171
CUSHION - REAR - INSTALLATION, SEAT
BACK.............................23-170
CUSHION - REAR - REMOVAL, SEAT....23-171
CUSHION - REAR - REMOVAL, SEAT
BACK
.............................23-170
CUSHION COVER - FRONT -
INSTALLATION, SEAT
.................23-167
CUSHION COVER - FRONT - REMOVAL,
SEAT
.............................23-167
CUSHION SIDE SHIELDS -
INSTALLATION, SEAT
.................23-167
CUSHION SIDE SHIELDS - REMOVAL,
SEAT
.............................23-167CUSTOMER PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-8
CV JOINT/BOOT-INNER - INSTALLATION . . . 3-17
CV JOINT/BOOT-INNER - REMOVAL.......3-15
CV JOINT/BOOT-OUTER - INSTALLATION . . . 3-13
CV JOINT/BOOT-OUTER - REMOVAL.......3-12
CYLINDER - DESCRIPTION, MASTER......5-24
CYLINDER - INSPECTION, MASTER........6-9
CYLINDER - INSTALLATION, FLIP-UP
GLASS SUPPORT...................23-139
CYLINDER - INSTALLATION, LOCK......23-125,
23-138
CYLINDER - INSTALLATION, LOCK.......19-11
CYLINDER - INSTALLATION, MASTER.....5-25
CYLINDER - INSTALLATION, SUPPORT . . . 23-120
CYLINDER - OPERATION, MASTER........5-24
CYLINDER - REMOVAL, FLIP-UP GLASS
SUPPORT.........................23-139
CYLINDER - REMOVAL, LOCK....23-125,23-137
CYLINDER - REMOVAL, LOCK...........19-10
CYLINDER - REMOVAL, MASTER.........5-25
CYLINDER - REMOVAL, SUPPORT......23-120
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-24
CYLINDER BORE HONING - STANDARD
PROCEDURE.........................9-39
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING......9-8
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING...............9-8
CYLINDER FLUID LEVEL - STANDARD
PROCEDURES, MASTER................5-26
CYLINDER HEAD - DESCRIPTION.........9-30
CYLINDER HEAD COVER(S) -
DESCRIPTION........................9-25
CYLINDER HEAD COVER(S) -
INSTALLATION....................9-26,9-34
CYLINDER HEAD COVER(S) - REMOVAL . . . 9-25,
9-34
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING....................9-19,9-30
CYLINDER LOCK SWITCH -
DESCRIPTION, DOOR..................8Q-9
CYLINDER LOCK SWITCH -
DESCRIPTION, TAILGATE...............8N-9
CYLINDER LOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR.................8Q-10
CYLINDER LOCK SWITCH - DIAGNOSIS
AND TESTING, TAILGATE...............8N-9
CYLINDER LOCK SWITCH -
INSTALLATION, DOOR.................8Q-10
CYLINDER LOCK SWITCH -
INSTALLATION, TAILGATE..............8N-10
CYLINDER LOCK SWITCH - OPERATION,
DOOR.............................8Q-10
CYLINDER LOCK SWITCH - OPERATION,
TAILGATE...........................8N-9
CYLINDER LOCK SWITCH - REMOVAL,
DOOR.............................8Q-10
CYLINDER LOCK SWITCH - REMOVAL,
TAILGATE..........................8N-10
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER . . 5-21,5-24
CYLINDERS - ASSEMBLY, WHEEL.........5-29
CYLINDERS - CLEANING, WHEEL.........5-28
CYLINDERS - DISASSEMBLY, WHEEL......5-28
CYLINDERS - INSPECTION, WHEEL.......5-29
CYLINDERS - INSTALLATION, WHEEL
.....5-29
CYLINDERS - REMOVAL, WHEEL
.........5-28
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR
.........9-9
DAMPER - INSTALLATION, VIBRATION
.....9-55
DAMPER - REMOVAL, VIBRATION
........9-54
DATA LINK CONNECTOR - DESCRIPTION
. . 8E-10
DATA LINK CONNECTOR - OPERATION
....8E-10
DAYTIME RUNNING LAMP RELAY -
DESCRIPTION
.......................8L-20
DAYTIME RUNNING LAMP RELAY -
INSTALLATION
.......................8L-21
DAYTIME RUNNING LAMP RELAY -
OPERATION
.........................8L-20
DAYTIME RUNNING LAMP RELAY -
REMOVAL
..........................8L-21
DECOUPLER - DIAGNOSIS AND
TESTING, GENERATOR
................8F-27
DECOUPLER PULLEY - DESCRIPTION,
GENERATOR
........................8F-26DECOUPLER PULLEY - INSTALLATION,
GENERATOR........................8F-30
DECOUPLER PULLEY - OPERATION,
GENERATOR........................8F-27
DECOUPLER PULLEY - REMOVAL,
GENERATOR........................8F-27
DEFINITION - DESCRIPTION, TRIP.......25-19
DEFLECTOR - INSTALLATION, WIND.....23-180
DEFLECTOR - REMOVAL, WIND........23-180
DEFOGGER - DESCRIPTION, REAR
WINDOW............................8G-3
DEFOGGER - OPERATION, REAR
WINDOW............................8G-3
DEFOGGER FUNCTION - DIAGNOSIS AND
TESTING, REAR HVAC CONTROL
ASSEMBLY WINDOW..................8G-9
DEFOGGER GRID - DESCRIPTION, REAR
WINDOW............................8G-5
DEFOGGER GRID - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-5
DEFOGGER GRID - OPERATION, REAR
WINDOW............................8G-5
DEFOGGER RELAY - DESCRIPTION,
REAR WINDOW.......................8G-6
DEFOGGER RELAY - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-6
DEFOGGER RELAY - INSTALLATION,
REAR WINDOW.......................8G-7
DEFOGGER RELAY - OPERATION, REAR
WINDOW............................8G-6
DEFOGGER RELAY - REMOVAL, REAR
WINDOW............................8G-7
DEFOGGER SWITCH - DESCRIPTION,
REAR WINDOW.......................8G-8
DEFOGGER SWITCH - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-8
DEFOGGER SWITCH - OPERATION, REAR
WINDOW............................8G-8
DEFOGGER SYSTEM - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-4
DEFROST DOO - INSTALLATION, FLOOR . . 24-37
DEFROST DOOR - REMOVAL...........24-35
DEFROST DOOR - REMOVAL, FLOOR.....24-36
DEFROST DOOR ACTUATOR -
INSTALLATION, FLOOR................24-25
DEFROST DOOR ACTUATOR - REMOVAL,
FLOOR.............................24-24
DEFROST DUCT/DEMISTER ADAPTOR -
REMOVAL..........................24-32
DEFROST/DEMISTER DUCT -
INSTALLATION.......................24-32
DELIVERY - DESCRIPTION, FUEL.........14-2
DELIVERY - OPERATION, FUEL...........14-3
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS...............8M-2
DEMISTER OUTLETS - DESCRIPTION.....24-29
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL RESTRAINT............8O-6
DETECTION PUMP - DESCRIPTION, LEAK . 25-27
DETECTION PUMP - INSTALLATION,
LEAK..............................25-28
DETECTION PUMP - OPERATION, LEAK . . . 25-28
DETECTION PUMP - REMOVAL, LEAK....25-28
DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE........................8W-01-8
DIAGNOSIS CHART - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-6
DIAGNOSIS, DIAGNOSIS AND TESTING -
WATER DRAINAGE AND WIND NOISE . . . 23-176
DIAGNOSTIC PROCEDURES, DIAGNOSIS
AND TESTING......................23-176
DIAGNOSTIC TROUBLE CODES -
DESCRIPTION........................25-2
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-3
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING......................8W-01-1
DIAGRAMS - HYDRAULIC SCHEMATICS,
SCHEMATICS.......................21-100
DIESEL - TORQUE, EXCEPT.............8F-23
DIFFERENTIAL - ASSEMBLY
........3-105,3-41
DIFFERENTIAL - DISASSEMBLY
.....3-105,3-41
DIFFERENTIAL - INSTALLATION
. 3-105,3-42,3-73
DIFFERENTIAL - REMOVAL
.....3-104,3-40,3-71
DIFFERENTIAL - TRAC-LOK - ASSEMBLY
. . 3-109,
3-77
KJINDEX 7
Description Group-Page Description Group-Page Description Group-Page

SPARK PLUG - OPERATION.............8I-12
SPARK PLUG - REMOVAL..............8I-15
SPARK PLUG CABLE RESISTANCE, 2.4L....8I-3
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-13
SPARK PLUGS, SPARK PLUG -
CLEANING..........................8I-15
SPARK PLUGS, SPECIFICATIONS..........8I-3
SPEAKER - DESCRIPTION..............8A-13
SPEAKER - INSTALLATION.............8A-15
SPEAKER - OPERATION...............8A-14
SPEAKER - REMOVAL.................8A-14
SPECIAL TOOLS - 3.7L ENGINE..........9-15
SPECIAL TOOLS - 8 1/4 AXLE...........3-98
SPECIAL TOOLS - BASE BRAKES..........5-7
SPECIAL TOOLS - BODY................23-5
SPECIAL TOOLS - COOLING.............7-14
SPECIAL TOOLS - FRONT AXLE..........3-34
SPECIAL TOOLS - FRONT SUSPENSION.....2-8
SPECIAL TOOLS - FUEL SYSTEM.........14-6
SPECIAL TOOLS - OUTER TIE ROD END
REMOVAL TOOL.....................19-15
SPECIAL TOOLS - POWER
DISTRIBUTION SYSTEMS............8W-97-2
SPECIAL TOOLS - POWER STEERING
PUMP.............................19-20
SPECIAL TOOLS - REAR AXLE...........3-63
SPECIAL TOOLS - RFE TRANSMISSION....21-120
SPECIAL TOOLS - STEERING COLUMN....19-8
SPECIAL TOOLS - WIRING/TERMINAL . 8W-01-10
SPECIAL TOOLS, BATTERY SYSTEM.......8F-7
SPECIFICATIONS, BATTERY SYSTEM......8F-6
SPECIFICATIONS, BRAKES - ABS.........5-33
SPECIFICATIONS, CHARGE CAPACITY.....24-42
SPECIFICATIONS, CLUTCH...............6-5
SPECIFICATIONS, DIAGNOSIS AND
TESTING............................22-8
SPECIFICATIONS, FLUID CAPACITIES.......0-4
SPECIFICATIONS, FRAME DIMENSIONS....13-3
SPECIFICATIONS, FRONT AXLE...........3-33
SPECIFICATIONS, GAP AND FLUSH.....23-116
SPECIFICATIONS, IGNITION TIMING.......8I-2
SPECIFICATIONS, LAMPS/LIGHTING -
EXTERIOR..........................8L-15
SPECIFICATIONS, LAMPS/LIGHTING -
INTERIOR..........................8L-71
SPECIFICATIONS, NV1500..............21-30
SPECIFICATIONS, OPENING DIMENSIONS . 23-111
SPECIFICATIONS, PAINT CODES........23-162
SPECIFICATIONS, REAR AXLE............3-62
SPECIFICATIONS, REMOTE KEYLESS
ENTRY TRANSMITTER.................8N-9
SPECIFICATIONS, SEALER LOCATIONS....23-87
SPECIFICATIONS, SPECIFICATIONS.......24-10
SPECIFICATIONS, STANDARD
PROCEDURE.........................23-4
SPECIFICATIONS, TORQUE..............13-6
SPECIFICATIONS, WELD AND
STRUCTURAL ADHESIVE LOCATIONS......23-9
SPEED CONTROL - DESCRIPTION........8P-1
SPEED CONTROL - OPERATION..........8P-1
SPEED CONTROL - TORQUE.............8P-2
SPEED SENSOR - DESCRIPTION, INPUT . 21-143
SPEED SENSOR - DESCRIPTION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, FRONT
WHEEL.............................5-34
SPEED SENSOR - INSTALLATION, INPUT . 21-143
SPEED SENSOR - INSTALLATION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, REAR
WHEEL.............................5-35
SPEED SENSOR - OPERATION, INPUT . . . 21-143
SPEED SENSOR - OPERATION, OUTPUT . . 21-152
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-34
SPEED SENSOR - REMOVAL, INPUT.....21-143
SPEED SENSOR - REMOVAL, OUTPUT . . . 21-152
SPEED SENSOR - REMOVAL, REAR
WHEEL.............................5-35
SPEEDOMETER - DESCRIPTION
.........8J-32
SPEEDOMETER - OPERATION
...........8J-32
SPLASH SHIELD - INSTALLATION,
FRONT WHEELHOUSE
................23-143
SPLASH SHIELD - INSTALLATION, REAR
WHEELHOUSE
......................23-144
SPLASH SHIELD - REMOVAL, FRONT
WHEELHOUSE
......................23-143SPLASH SHIELD - REMOVAL, REAR
WHEELHOUSE......................23-144
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-7
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-14
SPRING - INSTALLATION...........2-13,2-18
SPRING - REMOVAL...............2-13,2-18
SPRINGS - DESCRIPTION, VALVE.....9-29,9-38
SPRINGS - INSTALLATION, VALVE....9-29,9-38
SPRINGS - REMOVAL, VALVE........9-29,9-38
STABILIZER BAR - INSTALLATION....2-14,2-19
STABILIZER BAR - REMOVAL........2-14,2-19
STABILIZER BAR BUSHINGS -
INSTALLATION.........................2-9
STABILIZER BAR BUSHINGS - REMOVAL....2-9
STABILIZER LINK - INSTALLATION........2-14
STABILIZER LINK - REMOVAL............2-14
STAKING - STANDARD PROCEDURE,
HEAT ...............................23-3
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-39
STARTER MOTOR - INSTALLATION.......8F-41
STARTER MOTOR - REMOVAL..........8F-39
STARTER MOTOR, GAS POWERED.......8F-39
STARTER MOTOR RELAY - DESCRIPTION . 8F-41
STARTER MOTOR RELAY -
INSTALLATION.......................8F-43
STARTER MOTOR RELAY - OPERATION.....8F-42
STARTER MOTOR RELAY - REMOVAL.....8F-43
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-42
STARTING PROCEDURE - STANDARD
PROCEDURE, JUMP....................0-5
STARTING SYSTEM - DESCRIPTION......8F-32
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-33
STARTING SYSTEM - INSPECTION.......8F-37
STARTING SYSTEM - OPERATION........8F-32
STATE DISPLAY TEST MODE -
DESCRIPTION........................25-2
STEERING - DESCRIPTION..............19-1
STEERING - OPERATION................19-1
STEERING COLUMN, SPECIAL TOOLS.....19-8
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER.......19-3
STEERING LINKAGE - STANDARD
PROCEDURE........................19-16
STEERING PRESSURE SWITCH -
DESCRIPTION, POWER................19-22
STEERING PRESSURE SWITCH -
INSTALLATION, POWER...............19-22
STEERING PRESSURE SWITCH -
OPERATION, POWER..................19-22
STEERING PRESSURE SWITCH -
REMOVAL, POWER...................19-22
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-18
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-20
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-1
STEERING SYSTEM - DIAGNOSIS AND
TESTING, SUSPENSION.................2-1
STEERING WHEEL - INSTALLATION......19-12
STEERING WHEEL - REMOVAL..........19-12
STOP LAMP BULB - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP BULB - REMOVAL, CENTER
HIGH MOUNTED.....................8L-18
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-19
STRAP - DESCRIPTION, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRAP - INSTALLATION, CHECK . 23-121,23-128,
23-135
STRAP - INSTALLATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-11
STRAP - OPERATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRAP - REMOVAL, CHECK
.....23-121,23-128,
23-135
STRAP - REMOVAL, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRIKER - INSTALLATION, GLOVE BOX
LATCH
............................23-149STRIKER - INSTALLATION, HOOD AJAR
SWITCH............................8Q-14
STRIKER - INSTALLATION, LATCH......23-124,
23-132,23-137
STRIKER - INSTALLATION, REAR SEAT
BACK LATCH.......................23-171
STRIKER - REMOVAL, GLOVE BOX
LATCH ............................23-148
STRIKER - REMOVAL, HOOD AJAR
SWITCH............................8Q-13
STRIKER - REMOVAL, LATCH . . . 23-124,23-132,
23-137
STRIKER - REMOVAL, REAR SEAT BACK
LATCH ............................23-170
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS, WELD................23-9
STRUCTURAL COVER - DESCRIPTION.....9-55
STRUCTURAL COVER - INSTALLATION.....9-55
STRUCTURAL COVER - OPERATION.......9-55
STRUCTURAL COVER - REMOVAL........9-55
STUDS - INSTALLATION...............22-11
STUDS - REMOVAL...................22-11
SUCTION LINE - INSTALLATION, A/C.....24-49
SUCTION LINE - REMOVAL, A/C.........24-48
SUN VISOR - INSTALLATION..........23-160
SUN VISOR - REMOVAL..............23-160
SUN VISOR SUPPORT - INSTALLATION . . 23-160
SUN VISOR SUPPORT - REMOVAL......23-160
SUNROOF - DESCRIPTION............23-175
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-178
SUNSHADE - INSTALLATION...........23-179
SUNSHADE - REMOVAL..............23-179
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A.........8O-6
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING..............8O-6
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLIES - DESCRIPTION, 5 VOLT......8E-13
SUPPLIES - OPERATION, 5 VOLT........8E-15
SUPPORT - INSTALLATION, REAR
FASCIA..............................13-3
SUPPORT - INSTALLATION, SUN VISOR . . 23-160
SUPPORT - REMOVAL, REAR FASCIA......13-3
SUPPORT - REMOVAL, SUN VISOR.....23-160
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR.................23-161
SUPPORT CYLINDER - INSTALLATION . . . 23-120
SUPPORT CYLINDER - INSTALLATION,
FLIP-UP GLASS.....................23-139
SUPPORT CYLINDER - REMOVAL.......23-120
SUPPORT CYLINDER - REMOVAL,
FLIP-UP GLASS.....................23-139
SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO NOISE............8A-9
SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO NOISE...........8A-11
SUPPRESSION GROUND STRAP -
OPERATION, RADIO NOISE.............8A-10
SUPPRESSION GROUND STRAP -
REMOVAL, RADIO NOISE..............8A-10
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET............9-9
SUSPENSION - DIAGNOSIS AND
TESTING, REAR.......................2-17
SUSPENSION AND STEERING SYSTEM -
DIAGNOSIS AND TESTING...............2-1
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - DESCRIPTION, UPPER......2-20
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - OPERATION, UPPER........2-20
SUSPENSION, SPECIAL TOOLS - FRONT....2-8
SWING GATE - INSTALLATION.........23-138
SWING GATE - REMOVAL.............23-138
SWING GATE BELTLINE WEATHERSTRIP
- INSTALLATION....................23-186
SWING GATE BELTLINE WEATHERSTRIP
- REMOVAL
........................23-186
SWING GATE OPENING WEATHERSTRIP
- INSTALLATION
....................23-186
SWING GATE OPENING WEATHERSTRIP
- REMOVAL
........................23-186
SWITCH - DESCRIPTION
................8P-5
SWITCH - DESCRIPTION, A/C HIGH
PRESSURE
.........................24-17
KJINDEX 25
Description Group-Page Description Group-Page Description Group-Page

COOLANT TEMPERATURE SENSOR -
OPERATION, ENGINE...................7-21
COOLANT TEMPERATURE SENSOR -
REMOVAL, ENGINE....................7-21
COOLER - DESCRIPTION, TRANS.........7-30
COOLERS AND TUBES - STANDARD
PROCEDURE, FLUSHING................7-30
COOLING, SPECIAL TOOLS..............7-13
COOLING SYSTEM - OPERATION..........7-2
COOLING SYSTEM - REVERSE
FLUSHING - STANDARD PROCEDURE.....7-12
COOLING SYSTEM - STANDARD
PROCEDURE, DRAINING................7-11
COOLING SYSTEM - STANDARD
PROCEDURE, REFILLING................7-11
COOLING SYSTEM 2.4L ENGINE -
DESCRIPTION.........................7-1
COOLING SYSTEM DIAGNOSIS CHART -
DIAGNOSIS AND TESTING...............7-5
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-2
CORE AND OIL GALLERY PLUGS -
STANDARD PROCEDURE, ENGINE.........9-9
COVER - CLEANING, CYLINDER HEAD.....9-26
COVER - INSPECTION, CYLINDER HEAD . . . 9-26
COVER - INSTALLATION, CYLINDER
HEAD...............................9-26
COVER - REMOVAL, CYLINDER HEAD.....9-26
COVER(S) - INSTALLATION, TIMING
BELT ...............................9-53
COVER(S) - REMOVAL, TIMING BELT......9-53
CRANKSHAFT - DESCRIPTION...........9-32
CRANKSHAFT - INSPECTION.............9-34
CRANKSHAFT - INSTALLATION...........9-34
CRANKSHAFT - OPERATION.............9-33
CRANKSHAFT - REMOVAL..............9-33
CRANKSHAFT END PLAY - STANDARD
PROCEDURE.........................9-33
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........................9-37
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL...........................9-37
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........................9-39
CRANKSHAFT OIL SEAL - REAR -
REMOVAL...........................9-38
CRANKSHAFT SPROCKET -
INSTALLATION........................9-56
CRANKSHAFT SPROCKET - REMOVAL.....9-55
CROSS-OVER PIPE - INSTALLATION.......11-4
CROSS-OVER PIPE - REMOVAL..........11-4
CYLINDER BORE FITTING - STANDARD
PROCEDURE, PISTON TO...............9-30
CYLINDER BORE HONING - STANDARD
PROCEDURE.........................9-31
CYLINDER COMBUSTION PRESSURE
LEAKAGE TEST - DIAGNOSIS AND
TESTING.............................9-3
CYLINDER COMPRESSION PRESSURE
TEST - DIAGNOSIS AND TESTING.........9-3
CYLINDER HEAD - CLEANING............9-20
CYLINDER HEAD - DESCRIPTION.........9-19
CYLINDER HEAD - INSPECTION..........9-21
CYLINDER HEAD - INSTALLATION........9-21
CYLINDER HEAD - OPERATION...........9-19
CYLINDER HEAD - REMOVAL............9-20
CYLINDER HEAD COVER - CLEANING......9-26
CYLINDER HEAD COVER - INSPECTION....9-26
CYLINDER HEAD COVER -
INSTALLATION
........................9-26
CYLINDER HEAD COVER - REMOVAL
......9-26
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING
........................9-19
CYLINDER HEAD OFF - INSTALLATION
.....9-28
CYLINDER HEAD OFF - REMOVAL
........9-27
CYLINDER HEAD ON - INSTALLATION
.....9-28
CYLINDER HEAD ON - REMOVAL
.........9-27
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR OF
.......9-9
DAMPER - INSTALLATION, VIBRATION
.....9-43
DAMPER - REMOVAL, VIBRATION
........9-43
DAYTIME RUNNING LAMP RELAY -
DESCRIPTION
.......................8L-20
DAYTIME RUNNING LAMP RELAY -
INSTALLATION
.......................8L-21
DAYTIME RUNNING LAMP RELAY -
OPERATION
.........................8L-20DAYTIME RUNNING LAMP RELAY -
REMOVAL..........................8L-21
DESCRIPTION - OPERATION.............7-20
DESCRIPTION, BACKUP LAMP SWITCH . . . 8L-15
DESCRIPTION, BALANCE SHAFT..........9-59
DESCRIPTION, BRAKE LAMP SWITCH....8L-16
DESCRIPTION, CAMSHAFT(S)............9-23
DESCRIPTION, CATALYTIC CONVERTER....11-2
DESCRIPTION, COMBINATION FLASHER . . . 8L-19
DESCRIPTION, COOLANT RECOVERY
PRESS CONTAINER....................7-20
DESCRIPTION, COOLING SYSTEM 2.4L
ENGINE..............................7-1
DESCRIPTION, CRANKSHAFT............9-32
DESCRIPTION, CYLINDER HEAD..........9-19
DESCRIPTION, DAYTIME RUNNING
LAMP RELAY........................8L-20
DESCRIPTION, ENGINE - 2.4L.............9-3
DESCRIPTION, ENGINE BLOCK...........9-30
DESCRIPTION, ENGINE BLOCK HEATER -
2.4L................................7-20
DESCRIPTION, ENGINE COOLANT.........7-19
DESCRIPTION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
DESCRIPTION, ENGINE MOUNTING.......9-44
DESCRIPTION, EXHAUST MANIFOLD......9-53
DESCRIPTION, EXHAUST SYSTEM........11-1
DESCRIPTION, FRONT FOG LAMP RELAY . . 8L-22
DESCRIPTION, HAZARD SWITCH........8L-28
DESCRIPTION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
DESCRIPTION, HEADLAMP LEVELING
MOTOR............................8L-35
DESCRIPTION, HEADLAMP LEVELING
SWITCH............................8L-37
DESCRIPTION, HEADLAMP LOW BEAM
RELAY.............................8L-39
DESCRIPTION, HEAT SHIELDS...........11-4
DESCRIPTION, HOAT COOLANT..........7-18
DESCRIPTION, HOSE CLAMPS............7-1
DESCRIPTION, INTAKE MANIFOLD........9-51
DESCRIPTION, INTAKE/EXHAUST VALVES
& SEATS ............................9-27
DESCRIPTION, LAMP BAR.............8L-65
DESCRIPTION, LAMP BAR SWITCH......8L-67
DESCRIPTION, LAMPS/LIGHTING -
EXTERIOR...........................8L-2
DESCRIPTION, LUBRICATION............9-46
DESCRIPTION, MUFFLER...............11-4
DESCRIPTION, MULTI-FUNCTION
SWITCH............................8L-46
DESCRIPTION, OIL FILTER..............9-47
DESCRIPTION, OIL PRESSURE
SENSOR/SWITCH.....................9-48
DESCRIPTION, PARK LAMP RELAY.......8L-54
DESCRIPTION, PISTON & CONNECTING
ROD................................9-40
DESCRIPTION, RADIATOR...............7-22
DESCRIPTION, RADIATOR FAN -
ELECTRIC...........................7-26
DESCRIPTION, RADIATOR PRESSURE
CAP ................................7-25
DESCRIPTION, REAR FOG LAMP RELAY . . . 8L-56
DESCRIPTION, TRAILER TOW RELAY.....8L-62
DESCRIPTION, TRAILER TOW WIRING....8L-64
DESCRIPTION, TRANS COOLER..........7-30
DESCRIPTION, WATER PUMP - 2.4L......7-27
DIAGNOSIS - DIAGNOSIS AND TESTING,
LASH ADJUSTER (TAPPET) NOISE........9-28
DIAGNOSIS - DIAGNOSIS AND TESTING,
SERPENTINE DRIVE BELT...............7-15
DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, BACKUP
LAMP SWITCH......................8L-15
DIAGNOSIS AND TESTING, BRAKE LAMP
SWITCH............................8L-17
DIAGNOSIS AND TESTING, COOLING
SYSTEM DIAGNOSIS CHART
..............7-5
DIAGNOSIS AND TESTING, COOLING
SYSTEM LEAKS
........................7-2
DIAGNOSIS AND TESTING, CYLINDER
COMBUSTION PRESSURE LEAKAGE
TEST
................................9-3
DIAGNOSIS AND TESTING, CYLINDER
COMPRESSION PRESSURE TEST
..........9-3
DIAGNOSIS AND TESTING, CYLINDER
HEAD GASKET
........................9-19DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, ENGINE
DIAGNOSIS - PERFORMANCE.............9-5
DIAGNOSIS AND TESTING, ENGINE
MECHANICAL.........................9-7
DIAGNOSIS AND TESTING, ENGINE OIL
LEAK INSPECTION......................9-4
DIAGNOSIS AND TESTING, ENGINE OIL
PRESSURE CHECKING.................9-46
DIAGNOSIS AND TESTING, EXHAUST
SYSTEM............................11-2
DIAGNOSIS AND TESTING, FRONT FOG
LAMP RELAY........................8L-23
DIAGNOSIS AND TESTING, HEADLAMP
HIGH BEAM RELAY...................8L-34
DIAGNOSIS AND TESTING, HEADLAMP
LEVELING SWITCH...................8L-37
DIAGNOSIS AND TESTING, HEADLAMP
LOW BEAM RELAY...................8L-40
DIAGNOSIS AND TESTING, INTAKE
MANIFOLD LEAKS.....................9-51
DIAGNOSIS AND TESTING, LAMP BAR....8L-65
DIAGNOSIS AND TESTING, LAMPS/
LIGHTING - EXTERIOR.................8L-7
DIAGNOSIS AND TESTING, LASH
ADJUSTER (TAPPET) NOISE
DIAGNOSIS..........................9-28
DIAGNOSIS AND TESTING, MULTI-
FUNCTION SWITCH...................8L-50
DIAGNOSIS AND TESTING, ON-BOARD
DIAGNOSTICS (OBD)....................7-2
DIAGNOSIS AND TESTING, PARK LAMP
RELAY.............................8L-55
DIAGNOSIS AND TESTING,
PRELIMINARY CHECKS..................7-2
DIAGNOSIS AND TESTING, RADIATOR
PRESSURE CAP.......................7-25
DIAGNOSIS AND TESTING, REAR FOG
LAMP RELAY........................8L-57
DIAGNOSIS AND TESTING, SERPENTINE
DRIVE BELT DIAGNOSIS................7-15
DIAGNOSIS AND TESTING, TRAILER
TOW RELAY.........................8L-62
DIAGNOSIS CHART - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-5
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-2
DISASSEMBLY, OIL PUMP...............9-49
DRAINING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
DRIVE BELT DIAGNOSIS - DIAGNOSIS
AND TESTING, SERPENTINE.............7-15
ELECTRIC - DESCRIPTION, RADIATOR
FAN ................................7-26
ELECTRIC - INSTALLATION, RADIATOR
FAN ................................7-27
ELECTRIC - OPERATION, RADIATOR FAN . . . 7-26
ELECTRIC - REMOVAL, RADIATOR FAN....7-26
END PLAY - STANDARD PROCEDURE,
CRANKSHAFT........................9-33
END-PLAY - STANDARD PROCEDURE,
CAMSHAFT..........................9-23
ENGINE - 2.4L - DESCRIPTION............9-3
ENGINE - DESCRIPTION, COOLING
SYSTEM 2.4L.........................7-1
ENGINE - DIAGNOSIS AND TESTING.......9-5
ENGINE - INSTALLATION, 2.4L . . 7-14,7-17,7-22,
7-28
ENGINE - REMOVAL, 2.4L . . . 7-14,7-16,7-22,7-27
ENGINE - SPECIFICATIONS, 2.4L.........9-13
ENGINE - STANDARD PROCEDURE,
HYDROSTATIC LOCKED..................9-9
ENGINE ASSEMBLY - INSTALLATION......9-12
ENGINE ASSEMBLY - REMOVAL..........9-12
ENGINE BLOCK - DESCRIPTION..........9-30
ENGINE BLOCK HEATER - 2.4L -
DESCRIPTION........................7-20
ENGINE BLOCK HEATER - 2.4L -
OPERATION..........................7-20
ENGINE COOLANT - DESCRIPTION
........7-19
ENGINE COOLANT TEMPERATURE
SENSOR - DESCRIPTION
...............7-21
ENGINE COOLANT TEMPERATURE
SENSOR - INSTALLATION
...............7-22
ENGINE COOLANT TEMPERATURE
SENSOR - OPERATION
.................7-21
ENGINE COOLANT TEMPERATURE
SENSOR - REMOVAL
...................7-21
2 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page