2002 JEEP LIBERTY Vacuum

OPERATION
The PCV system operates by engine intake mani-
fold vacuum. Filtered air is routed into the crankcase
through the air cleaner hose and crankcase breath-
er(s) (if used). The metered air, along with crankcase
vapors, are drawn through the PCV valve and into a
passage in the intake manifold. The PCV system
manages crankcase pressure and meters blow-by
gases to the intake system, reducing engine sludge
formation.
The PCV valve contains a spring loaded plunger.
This plunger meters the amount of crankcase vapors
routed into the combustion chamber based on intake
manifold vacuum.
TYPICALPCV valves are shown in (Fig. 9), (Fig.
10) and (Fig. 11).
When the engine is not operating, or during an
engine pop-back, the spring forces the plunger back
against the seat (Fig. 9). This will prevent vapors
from flowing through the valve.
During periods of high manifold vacuum, such as
idle or cruising speeds, vacuum is sufficient to com-
pletely compress spring. It will then pull the plunger
to the top of the valve (Fig. 10). In this position there
is minimal vapor flow through the valve.
During periods of moderate manifold vacuum, the
plunger is only pulled part way back from inlet. This
results in maximum vapor flow through the valve
(Fig. 11).
DIAGNOSIS AND TESTING - PCV VALVE
3.7L
(1) Disconnect PCV line/hose (Fig. 7) by discon-
necting rubber connecting hose at PCV valve fitting.
(2) Remove PCV valve at oil filler tube by rotating
PCV valve downward until locating tabs have been
freed at cam lock (Fig. 7). After tabs have cleared,
pull valve straight out from filler tube.To prevent
damage to PCV valve locating tabs, valve must
be pointed downward for removal. Do not force
valve from oil filler tube.
(3) After valve is removed, check condition of valve
o-ring (Fig. 7). Also, PCV valve should rattle when
shaken.
(4) Reconnect PCV valve to its connecting line/
hose.
(5) Start engine and bring to idle speed.
(6) If valve is not plugged, a hissing noise will be
heard as air passes through valve. Also, a strong vac-
uum should be felt with a finger placed at valve
inlet.
(7) If vacuum is not felt at valve inlet, check line/
hose for kinks or for obstruction. If necessary, clean
out intake manifold fitting at rear of manifold. Do
this by turning a 1/4 inch drill (by hand) through the
fitting to dislodge any solid particles. Blow out the
fitting with shop air. If necessary, use a smaller drill
to avoid removing any metal from the fitting.
(8)Do not attempt to clean the old PCV valve.
(9) Return PCV valve back to oil filler tube by
placing valve locating tabs (Fig. 7) into cam lock.
Press PCV valve in and rotate valve upward. A slight
click will be felt when tabs have engaged cam lock.
Valve should be pointed towards rear of vehicle.
(10) Connect PCV line/hose and connecting rubber
hose to PCV valve.
(11) Disconnect rubber hose from fresh air fitting
at air cleaner resonator box. Start engine and bring
to idle speed. Hold a piece of stiff paper (such as a
parts tag) loosely over the opening of the discon-
nected rubber hose.
(12) The paper should be drawn against the hose
opening with noticeable force. This will be after
allowing approximately one minute for crankcase
pressure to reduce.
Fig. 9 Engine Off or Engine Pop-BackÐNo Vapor
Flow
Fig. 10 High Intake Manifold VacuumÐMinimal
Vapor Flow
Fig. 11 Moderate Intake Manifold VacuumÐ
Maximum Vapor Flow
KJEVAPORATIVE EMISSIONS 25 - 31
PCV VALVE (Continued)

(13) If vacuum is not present, disconnect each PCV
system hose at top of each crankcase breather (Fig.
8). Check for obstructions or restrictions.
(14) If vacuum is still not present, remove each
PCV system crankcase breather (Fig. 8) from each
cylinder head. Check for obstructions or restrictions.
If plugged, replace breather. Tighten breather to 12
N´m (106 in. lbs.) torque. Do not attempt to clean
breather
(15) If vacuum is still not present, disconnect each
PCV system hose at each fitting and check for
obstructions or restrictions.
REMOVAL
2.4L
The PCV valve is attached to the left/front side of
the valve cover (Fig. 5). It is secured with 1 bolt. An
o-ring is used to seal valve to valve cover (Fig. 6).
(1) Remove hose from valve (Fig. 5). Check condi-
tion of hose.
(2) Remove 1 bolt.
(3) Remove PCV valve from valve cover.
(4) Check condition of valve o-ring.
3.7L
The PCV valve is located on the oil filler tube (Fig.
12). Two locating tabs are located on the side of the
valve (Fig. 12). These 2 tabs fit into a cam lock in the
oil filler tube. An o-ring seals the valve to the filler
tube.
(1) Disconnect PCV line/hose (Fig. 12) by discon-
necting rubber hose at PCV valve fitting.
(2) Remove PCV valve at oil filler tube by rotating
PCV valve downward (counter-clockwise) until locat-
ing tabs have been freed at cam lock (Fig. 12). After
tabs have cleared, pull valve straight out from filler
tube.To prevent damage to PCV valve locating
tabs, valve must be pointed downward for
removal. Do not force valve from oil filler tube.
(3) After valve is removed, check condition of valve
o-ring (Fig. 12).
INSTALLATION
2.4L
(1) Check condition of PCV valve o-ring.
(2) Install PCV valve into valve cover.
(3) Install PCV valve mounting bolt.
(4) Install hose to valve.3.7L
The PCV valve is located on the oil filler tube. Two
locating tabs are located on the side of the valve.
These 2 tabs fit into a cam lock in the oil filler tube.
An o-ring seals the valve to the filler tube.
(1) Return PCV valve back to oil filler tube by
placing valve locating tabs into cam lock. Press PCV
valve in and rotate valve upward. A slight click will
be felt when tabs have engaged cam lock. Valve
should be pointed towards rear of vehicle.
(2) Connect PCV line/hose and rubber hose to PCV
valve.
Fig. 12 PCV Valve/Oil Filler Tube Location
1 - O-RING
2 - LOCATING TABS
3 - CAM LOCK
4 - OIL FILLER TUBE
5 - PCV LINE/HOSE
6 - P C V VA LV E
25 - 32 EVAPORATIVE EMISSIONSKJ
PCV VALVE (Continued)

VACUUM LINES
DESCRIPTION
A vacuum schematic for emission related items can
be found on the VECI label. Refer to Vehicle Emis-
sion Control Information (VECI) Label for label loca-
tion.
VAPOR CANISTER
DESCRIPTION
A maintenance free, EVAP canister is used on all
gasoline powered models. The EVAP canister is
located near the left/front corner of the fuel tank.
OPERATION
The EVAP canister is filled with granules of an
activated carbon mixture. Fuel vapors entering the
EVAP canister are absorbed by the charcoal granules.
The canister serves two functions: as a temporary
fuel vapor storage point while refueling the vehicle
for the ORVR system, as a temporary vapor storage
point while the engine is running.
Fuel tank pressure vents into the EVAP canister.
Fuel vapors are temporarily held in the canister until
they can be drawn into the intake manifold. The duty
cycle EVAP canister purge solenoid allows the EVAP
canister to be purged at predetermined times and at
certain engine operating conditions.
Refer to ORVR for additional information.
REMOVAL
The EVAP canister is located near front of fuel
tank and next to left/rear spring. (Fig. 13).
(1) Raise vehicle.
(2) Disconnect vacuum hoses/lines at EVAP canis-
ter. Note location of lines before removal.
(3) Remove EVAP canister and mounting bracket
assembly from body (2 bolts).
(4) Remove canister-to-mounting bracket bolt.
(5) Slide 2 canister mounting pins from mounting
bracket (Fig. 14).
INSTALLATION
(1) Slide 2 canister mounting pins into mounting
bracket (Fig. 14).
(2) Install canister-to-mounting bracket bolt.
(3) Position canister and bracket assembly to body.
(4) Install 2 mounting bracket bolts. Tighten to 47
N´m (35 ft. lbs.) torque.
(5) Connect vacuum hoses/lines at EVAP canister.
(6) Lower vehicle.
Fig. 13 EVAP CANISTER LOCATION
1 - LEFT/REAR SPRING
2 - EVAP CANISTER
3 - MOUNTING BRACKET
4 - BRACKET BOLTS
5 - VACUUM LINES
Fig. 14 EVAP CANISTER MOUNTING PINS
1 - MOUNTING PINS
2 - MOUNTING BRACKET
3 - EVAP CANISTER
KJEVAPORATIVE EMISSIONS 25 - 33

CASE BEARINGS - REMOVAL,
DIFFERENTIAL...............3-110,3-43,3-79
CASE, NV231 - TRANSFER............21-206
CASE, NV242 - TRANSFER............21-244
CASE SKID PLATE - INSTALLATION,
TRANSFER...........................13-7
CASE SKID PLATE - REMOVAL,
TRANSFER...........................13-7
CASE, SPECIFICATIONS - NV242
TRANSFER.........................21-244
CASTER ADJUSTMENT - STANDARD
PROCEDURE, CAMBER..................2-5
CASTER AND TOE ADJUSTMENT -
STANDARD PROCEDURE, CAMBER........2-5
CATALYTIC CONVERTER - DESCRIPTION . . . 11-2
CATALYTIC CONVERTER - INSPECTION....11-3
CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-2
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING......................21-125
CAUTION - SERVICE CAUTIONS.........24-39
CAUTION, HALF SHAFT.................3-10
CAUTION, REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS.................24-40
CAUTIONS, CAUTION - SERVICE.........24-39
CD CHANGER - DESCRIPTION...........8A-7
CD CHANGER - INSTALLATION...........8A-7
CD CHANGER - OPERATION.............8A-7
CD CHANGER - REMOVAL..............8A-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-6
CENTER - OPERATION, POWER
DISTRIBUTION....................8W-97-7
CENTER - REMOVAL, POWER
DISTRIBUTION....................8W-97-7
CENTER ASSEMBLY, ASSEMBLY -
POWER DISTRIBUTION.............8W-97-10
CENTER BEZEL - INSTALLATION,
INSTRUMENT PANEL.................23-154
CENTER BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
CENTER DISASSEMBLY, DISASSEMBLY -
POWER DISTRIBUTION..............8W-97-7
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION................8L-19
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL....................8L-18
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION.................8L-19
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL....................8L-19
CENTER SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-33
CENTER SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-32
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-14
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY...................Intro.-9
CHAIN COVER(S) - INSTALLATION,
TIMING BELT.........................9-76
CHAIN COVER(S) - REMOVAL, TIMING
BELT ...............................9-74
CHAIN WEAR, STANDARD PROCEDURE -
MEASURING TIMING...................9-71
CHANGER - DESCRIPTION, CD...........8A-7
CHANGER - INSTALLATION, CD..........8A-7
CHANGER - OPERATION, CD.............8A-7
CHANGER - REMOVAL, CD..............8A-7
CHANNEL - INSTALLATION, GLASS RUN . 23-123,
23-130
CHANNEL - REMOVAL, GLASS RUN....23-123,
23-130
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-41
CHARGE CAPACITY - SPECIFICATIONS....24-42
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-8
CHARGING INDICATOR - DESCRIPTION . . . 8J-15
CHARGING INDICATOR - OPERATION.....8J-15
CHARGING SYSTEM - DESCRIPTION
.....8F-22
CHARGING SYSTEM - DIAGNOSIS AND
TESTING
...........................8F-22
CHARGING SYSTEM - OPERATION
.......8F-22
CHART - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIAGNOSIS
............7-6
CHART, SPECIFICATIONS - TORQUE
.....19-15,
19-19,19-8CHART, SPECIFICATIONS - TORQUE....2-17,2-8
CHECK - STANDARD PROCEDURE, FLUID
LEVEL............................21-126
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME.....................21-148
CHECK STRAP - INSTALLATION . . 23-121,23-128,
23-135
CHECK STRAP - REMOVAL.....23-121,23-128,
23-135
CHECK VALVE - DESCRIPTION, FRONT....8R-8
CHECK VALVE - DESCRIPTION, FUEL
TANK ..............................14-28
CHECK VALVE - DESCRIPTION, REAR....8R-34
CHECK VALVE - DESCRIPTION, VACUUM . . 24-28
CHECK VALVE - INSTALLATION, FRONT....8R-9
CHECK VALVE - INSTALLATION, FUEL
TANK ..............................14-28
CHECK VALVE - INSTALLATION, REAR....8R-35
CHECK VALVE - INSTALLATION, VACUUM . 24-28
CHECK VALVE - OPERATION, FRONT......8R-9
CHECK VALVE - OPERATION, FUEL TANK . . 14-28
CHECK VALVE - OPERATION, REAR......8R-34
CHECK VALVE - OPERATION, VACUUM....24-28
CHECK VALVE - REMOVAL, FRONT.......8R-9
CHECK VALVE - REMOVAL, FUEL TANK . . . 14-28
CHECK VALVE - REMOVAL, REAR.......8R-34
CHECK VALVE - REMOVAL, VACUUM.....24-28
CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING, AIR.......................21-80
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-3
CHILD TETHER ANCHOR - DESCRIPTION . . 8O-13
CHILD TETHER ANCHOR - OPERATION . . . 8O-13
CHIME WARNING SYSTEM -
DESCRIPTION........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-6
CHIME WARNING SYSTEM - OPERATION . . . 8B-2
CHOKE AND RELAY - DESCRIPTION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - DIAGNOSIS AND
TESTING, AMPLIFIER..................8A-4
CHOKE AND RELAY - INSTALLATION,
AMPLIFIER..........................8A-4
CHOKE AND RELAY - OPERATION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - REMOVAL,
AMPLIFIER..........................8A-4
CIGAR LIGHTER OUTLET -
DESCRIPTION.....................8W-97-2
CIGAR LIGHTER OUTLET - DIAGNOSIS
AND TESTING.....................8W-97-2
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CLEVIS BRACKET - INSTALLATION........2-13
CLEVIS BRACKET - REMOVAL...........2-13
CLOCKSPRING - DESCRIPTION.........8O-13
CLOCKSPRING - INSTALLATION.........8O-16
CLOCKSPRING - OPERATION...........8O-14
CLOCKSPRING - REMOVAL............8O-15
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-14
CLUSTER - ASSEMBLY, INSTRUMENT....8J-10
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-7
CLUSTER - DISASSEMBLY, INSTRUMENT . . . 8J-9
CLUSTER - INSTALLATION, INSTRUMENT . 8J-11
CLUSTER - OPERATION, INSTRUMENT.....8J-4
CLUSTER - REMOVAL, INSTRUMENT......8J-9
CLUSTER BEZEL - INSTALLATION.......23-147
CLUSTER BEZEL - REMOVAL..........23-147
CLUTCH - ASSEMBLY, LOW/REVERSE
. . . 21-146
CLUTCH - CLEANING, LOW/REVERSE
....21-146
CLUTCH - DESCRIPTION
.................6-1
CLUTCH - DIAGNOSIS AND TESTING
.......6-2
CLUTCH - DISASSEMBLY, LOW/REVERSE
. 21-145
CLUTCH - INSPECTION, A/C
COMPRESSOR
.......................24-14
CLUTCH - INSPECTION, LOW/REVERSE
. . 21-146
CLUTCH - INSTALLATION, A/C
COMPRESSOR
.......................24-14
CLUTCH - OPERATION
..................6-1
CLUTCH - REMOVAL, A/C COMPRESSOR
. . 24-13
CLUTCH - SPECIFICATIONS
...............6-5
CLUTCH - WARNING
....................6-2
CLUTCH ASSEMBLY - ASSEMBLY, INPUT
. 21-138CLUTCH ASSEMBLY - DESCRIPTION,
INPUT............................21-133
CLUTCH ASSEMBLY - DISASSEMBLY,
INPUT............................21-135
CLUTCH ASSEMBLY - OPERATION,
INPUT............................21-135
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR........24-12
CLUTCH COIL - DIAGNOSIS AND
TESTING, A/C COMPRESSOR...........24-12
CLUTCH DISC - INSTALLATION............6-6
CLUTCH DISC - REMOVAL...............6-6
CLUTCH OPERATION - DIAGNOSIS AND
TESTING, AIR CHECKING
TRANSMISSION......................21-80
CLUTCH PEDAL - INSTALLATION.........6-10
CLUTCH PEDAL - REMOVAL.............6-10
CLUTCH PEDAL POSITION SWITCH -
DESCRIPTION........................6-11
CLUTCH PEDAL POSITION SWITCH -
DIAGNOSIS AND TESTING..............6-11
CLUTCH PEDAL POSITION SWITCH -
OPERATION..........................6-11
CLUTCH RELAY - DESCRIPTION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-15
CLUTCH RELAY - INSTALLATION, A/C
COMPRESSOR.......................24-16
CLUTCH RELAY - OPERATION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - REMOVAL, A/C
COMPRESSOR........................24-16
CLUTCH RELEASE BEARING -
INSTALLATION.........................6-6
CLUTCH RELEASE BEARING - REMOVAL....6-6
CLUTCH SWITCH OVERRIDE RELAY -
DESCRIPTION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
INSTALLATION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
OPERATION..........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
REMOVAL...........................6-10
CLUTCHES - DESCRIPTION, HOLDING . . . 21-131
CLUTCHES - OPERATION, HOLDING.....21-132
CMTC LAMP REPLACEMENT -
STANDARD PROCEDURE...............8M-2
COAT FINISH - DESCRIPTION, BASE
COAT/CLEAR.......................23-162
COAT/CLEAR COAT FINISH -
DESCRIPTION, BASE.................23-162
CODE - DESCRIPTION, PAINT..........23-162
CODES - DESCRIPTION, DIAGNOSTIC
TROUBLE............................25-2
CODES - SPECIFICATIONS, PAINT.......23-162
CODES - STANDARD PROCEDURE,
ERASING TRANSMITTER...............8M-8
CODES - STANDARD PROCEDURE,
SETTING TRANSMITTER...............8M-9
COIL - DESCRIPTION, IGNITION..........8I-9
COIL - DIAGNOSIS AND TESTING, A/C
COMPRESSOR CLUTCH...............24-12
COIL - INSTALLATION, IGNITION.........8I-10
COIL - OPERATION, IGNITION............8I-9
COIL - REMOVAL, IGNITION............8I-10
COIL CAPACITOR - DESCRIPTION,
IGNITION...........................8I-16
COIL CAPACITOR - INSTALLATION,
IGNITION...........................8I-16
COIL CAPACITOR - OPERATION,
IGNITION...........................8I-16
COIL CAPACITOR - REMOVAL, IGNITION . . . 8I-16
COIL RESISTANCE, 2.4L - IGNITION
.......8I-2
COIL RESISTANCE, 3.7L V-6 - IGNITION
....8I-3
COLLAPSIBLE SPACER - INSTALLATION
....3-70
COLLAPSIBLE SPACER - REMOVAL
.......3-70
COLUMN - DESCRIPTION
...............19-5
COLUMN - INSTALLATION
...............19-7
COLUMN - REMOVAL
..................19-5
COLUMN, SPECIAL TOOLS - STEERING
....19-8
COMBINATION FLASHER - DESCRIPTION
. . 8L-19
COMBINATION FLASHER - OPERATION
. . . 8L-19
COMBUSTION PRESSURE LEAKAGE -
DIAGNOSIS AND TESTING, CYLINDER
......9-8
COMMUNICATION - DESCRIPTION
........8E-8
COMMUNICATION - OPERATION
..........8E-8
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page

LATCH - ACCESS PANEL - REMOVAL....23-139
LATCH - INSTALLATION . . 23-120,23-124,23-131,
23-137
LATCH - INSTALLATION, FLIP-UP GLASS . 23-136
LATCH - INSTALLATION, FLOOR
CONSOLE LID......................23-158
LATCH - INSTALLATION, GLOVE BOX....23-148
LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT BACK...........23-170
LATCH / LOCK - REMOVAL, FOLDING
REAR SEAT BACK...................23-170
LATCH - REMOVAL......23-120,23-124,23-131,
23-137
LATCH - REMOVAL, FLIP-UP GLASS.....23-136
LATCH - REMOVAL, FLOOR CONSOLE
LID...............................23-158
LATCH - REMOVAL, GLOVE BOX........23-148
LATCH RELEASE CABLE - INSTALLATION . 23-120
LATCH RELEASE CABLE - REMOVAL....23-120
LATCH RELEASE HANDLE -
INSTALLATION......................23-120
LATCH RELEASE HANDLE - REMOVAL . . . 23-120
LATCH STRIKER - INSTALLATION......23-124,
23-132,23-137
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-149
LATCH STRIKER - INSTALLATION, REAR
SEAT BACK........................23-171
LATCH STRIKER - REMOVAL....23-124,23-132,
23-137
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-148
LATCH STRIKER - REMOVAL, REAR
SEAT BACK........................23-170
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID...........21-80
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL..........................9-60
LEAK DETECTION PUMP - DESCRIPTION . . 25-27
LEAK DETECTION PUMP - INSTALLATION . 25-28
LEAK DETECTION PUMP - OPERATION....25-28
LEAK DETECTION PUMP - REMOVAL.....25-28
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-3
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE.......9-8
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-4
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-68
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-61
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-8
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-21
LEFT POWER SEAT SWITCH -
DESCRIPTION.......................8N-16
LEFT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-17
LEFT POWER SEAT SWITCH -
INSTALLATION......................8N-18
LEFT POWER SEAT SWITCH -
OPERATION
.........................8N-17
LEFT POWER SEAT SWITCH - REMOVAL
. . 8N-18
LEFT SIDE - INSTALLATION
.........2-12,2-15
LEFT SIDE - REMOVAL
.............2-11,2-15
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID
........21-125
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-54
LEVEL - STANDARD PROCEDURES,
MASTER CYLINDER FLUID
..............5-26
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
.................21-126
LEVEL SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL
.......................14-9
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
...................14-9
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
.................14-10
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
.....................14-9
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-9LEVEL SWITCH - DESCRIPTION,
WASHER FLUID.....................8R-17
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-18
LEVEL SWITCH - OPERATION, WASHER
FLUID.............................8R-17
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-17
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP.........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LEVER - INSTALLATION................5-31
LEVER - INSTALLATION, SHIFT . . . 21-214,21-249
LEVER - REMOVAL....................5-31
LEVER - REMOVAL, SHIFT......21-213,21-248
LHD - INSTALLATION...............8W-97-6
LHD - REMOVAL....................8W-97-5
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LID LATCH - INSTALLATION, FLOOR
CONSOLE..........................23-158
LID LATCH - REMOVAL, FLOOR
CONSOLE..........................23-158
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITS - DESCRIPTION, HIGH AND LOW . . 25-20
LINE - DESCRIPTION, REFRIGERANT.....24-38
LINE - INSTALLATION, A/C DISCHARGE . . . 24-47
LINE - INSTALLATION, A/C LIQUID.......24-47
LINE - INSTALLATION, A/C SUCTION.....24-49
LINE - REMOVAL, A/C DISCHARGE.......24-46
LINE - REMOVAL, A/C LIQUID...........24-47
LINE - REMOVAL, A/C SUCTION.........24-48
LINE AND HOSES - DIAGNOSIS AND
TESTING, BRAKE.......................5-8
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-144
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-144
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-144
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-144
LINES - DESCRIPTION, BRAKE............5-8
LINES - DESCRIPTION, FUEL...........14-10
LINES - DESCRIPTION, VACUUM........25-33
LINK - INSTALLATION, STABILIZER.......2-14
LINK - REMOVAL, STABILIZER...........2-14
LINK CONNECTOR - DESCRIPTION, DATA . 8E-10
LINK CONNECTOR - OPERATION, DATA . . . 8E-10
LINKAGE - INSTALLATION................6-9
LINKAGE - REMOVAL...................6-8
LINKAGE - STANDARD PROCEDURE,
STEERING..........................19-16
LIQUID LINE - INSTALLATION, A/C.......24-47
LIQUID LINE - REMOVAL, A/C...........24-47
LOAD TEST - STANDARD PROCEDURE....8F-12
LOAD VALUE - DESCRIPTION
...........25-20
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-4
LOCATIONS - SPECIFICATIONS, SEALER
. . 23-87LOCATIONS - SPECIFICATIONS, WELD
AND STRUCTURAL ADHESIVE...........23-9
LOCK - INSTALLATION, FOLDING REAR
SEAT BACK LATCH..................23-170
LOCK - REMOVAL, FOLDING REAR SEAT
BACK LATCH.......................23-170
LOCK / UNLOCK SWITCH -
INSTALLATION, DOOR.................8N-5
LOCK / UNLOCK SWITCH - REMOVAL,
DOOR..............................8N-4
LOCK CYLINDER - INSTALLATION......23-125,
23-138
LOCK CYLINDER - INSTALLATION.......19-11
LOCK CYLINDER - REMOVAL....23-125,23-137
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, DOOR.....8N-5
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-5
LOCK MOTOR - OPERATION, DOOR.......8N-5
LOCK OUT - ADJUSTMENT..............5-30
LOCK RELAY - DESCRIPTION, DOOR......8N-6
LOCK RELAY - DIAGNOSIS AND
TESTING, DOOR......................8N-6
LOCK RELAY - INSTALLATION, DOOR.....8N-7
LOCK RELAY - OPERATION, DOOR........8N-6
LOCK RELAY - REMOVAL, DOOR.........8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8Q-9
LOCK SWITCH - DESCRIPTION,
TAILGATE CYLINDER...................8N-9
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8Q-10
LOCK SWITCH - DIAGNOSIS AND
TESTING, TAILGATE CYLINDER..........8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - INSTALLATION,
TAILGATE CYLINDER..................8N-10
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - OPERATION, TAILGATE
CYLINDER...........................8N-9
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - REMOVAL, TAILGATE
CYLINDER..........................8N-10
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-3
LOCK/UNLOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR..................8N-4
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-38
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-37
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP
.........................8L-40
LOW FUEL INDICATOR - DESCRIPTION
. . . 8J-22
LOW FUEL INDICATOR - OPERATION
.....8J-22
LOW INDICATOR - DESCRIPTION,
COOLANT
...........................8J-15
LOW INDICATOR - OPERATION,
COOLANT
...........................8J-16
LOW LIMITS - DESCRIPTION, HIGH
......25-20
LOW MODE INDICATOR - DESCRIPTION,
FOUR
..............................8J-29
LOW MODE INDICATOR - OPERATION,
FOUR
..............................8J-30
LOW OIL PRESSURE INDICATOR -
DESCRIPTION
.......................8J-23
LOW OIL PRESSURE INDICATOR -
OPERATION
.........................8J-23
LOW PRESSURE SWITCH -
DESCRIPTION, A/C
...................24-18
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C
...................24-19
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-19
KJINDEX 15
Description Group-Page Description Group-Page Description Group-Page

RELAY - OPERATION, FRONT FOG LAMP . . 8L-22
RELAY - OPERATION, FUEL PUMP.......14-34
RELAY - OPERATION, HEADLAMP HIGH
BEAM..............................8L-33
RELAY - OPERATION, HEADLAMP LOW
BEAM..............................8L-39
RELAY - OPERATION, PARK LAMP.......8L-54
RELAY - OPERATION, REAR FOG LAMP . . . 8L-57
RELAY - OPERATION, REAR WINDOW
DEFOGGER..........................8G-6
RELAY - OPERATION, STARTER MOTOR . . . 8F-42
RELAY - OPERATION, TRAILER TOW.....8L-62
RELAY - OPERATION, TRANSMISSION
CONTROL.........................21-168
RELAY - OPERATION, WIPER HIGH/LOW . . 8R-23
RELAY - OPERATION, WIPER ON/OFF....8R-25
RELAY - REMOVAL................8W-97-14
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-16
RELAY - REMOVAL, AMPLIFIER CHOKE....8A-4
RELAY - REMOVAL, BLOWER MOTOR....24-21
RELAY - REMOVAL, CLUTCH SWITCH
OVERRIDE...........................6-10
RELAY - REMOVAL, DAYTIME RUNNING
LAMP..............................8L-21
RELAY - REMOVAL, DOOR LOCK.........8N-6
RELAY - REMOVAL, FRONT FOG LAMP . . . 8L-24
RELAY - REMOVAL, FUEL PUMP........14-34
RELAY - REMOVAL, HEADLAMP HIGH
BEAM..............................8L-34
RELAY - REMOVAL, HEADLAMP LOW
BEAM..............................8L-40
RELAY - REMOVAL, HORN..............8H-3
RELAY - REMOVAL, PARK LAMP........8L-55
RELAY - REMOVAL, REAR FOG LAMP....8L-58
RELAY - REMOVAL, REAR WINDOW
DEFOGGER..........................8G-7
RELAY - REMOVAL, STARTER MOTOR....8F-43
RELAY - REMOVAL, TRAILER TOW.......8L-63
RELAY - REMOVAL, WIPER HIGH/LOW . . . 8R-24
RELAY - REMOVAL, WIPER ON/OFF......8R-26
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-4
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-4
RELEASE BEARING - INSTALLATION,
CLUTCH..............................6-6
RELEASE BEARING - REMOVAL, CLUTCH . . . 6-6
RELEASE CABLE - INSTALLATION, LATCH . 23-120
RELEASE CABLE - REMOVAL, LATCH....23-120
RELEASE HANDLE - INSTALLATION,
LATCH ............................23-120
RELEASE HANDLE - REMOVAL, LATCH . . 23-120
RELEASE SWITCH - DIAGNOSIS AND
TESTING, FLIP-UP GLASS..............8N-5
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-42
RELIEF VALVE - OPERATION, HIGH
PRESSURE.........................24-42
REMOTE KEYLESS ENTRY MODULE -
DESCRIPTION........................8N-7
REMOTE KEYLESS ENTRY MODULE -
DIAGNOSIS AND TESTING..............8N-7
REMOTE KEYLESS ENTRY MODULE -
INSTALLATION.......................8N-7
REMOTE KEYLESS ENTRY MODULE -
OPERATION..........................8N-7
REMOTE KEYLESS ENTRY MODULE -
REMOVAL...........................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-8
REMOTE KEYLESS ENTRY
TRANSMITTER - SPECIFICATIONS........8N-9
REMOTE SWITCHES - DESCRIPTION.....8A-11
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-12
REMOTE SWITCHES - INSTALLATION.....8A-13
REMOTE SWITCHES - OPERATION.......8A-12
REMOTE SWITCHES - REMOVAL
........8A-13
REPAIR - DESCRIPTION, THREADED
HOLE
.............................Intro.-4
REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD
..................21-81
REPAIR - STANDARD PROCEDURE,
REAR GLASS HEATING GRID
............8G-4
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE
...............9-9REPAIRING LEAKS - STANDARD
PROCEDURE.........................22-8
REPEATER LAMP BULB - INSTALLATION . . 8L-60
REPEATER LAMP BULB - REMOVAL......8L-60
REPEATER LAMP UNIT - INSTALLATION . . 8L-61
REPEATER LAMP UNIT - REMOVAL......8L-60
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
RESERVOIR - DESCRIPTION, VACUUM....8P-7
RESERVOIR - DESCRIPTION, WASHER . . . 8R-21
RESERVOIR - DIAGNOSIS AND TESTING,
VACUUM............................8P-7
RESERVOIR - INSTALLATION, FLUID......5-26
RESERVOIR - INSTALLATION, VACUUM....8P-8
RESERVOIR - INSTALLATION, WASHER . . . 8R-22
RESERVOIR - OPERATION, VACUUM......8P-7
RESERVOIR - OPERATION, WASHER.....8R-21
RESERVOIR - REMOVAL, FLUID..........5-26
RESERVOIR - REMOVAL, VACUUM........8P-7
RESERVOIR - REMOVAL, WASHER......8R-21
RESISTANCE, 2.4L - IGNITION COIL.......8I-2
RESISTANCE, 2.4L - SPARK PLUG CABLE . . . 8I-3
RESISTANCE, 3.7L V-6 - IGNITION COIL....8I-3
RESISTOR - DESCRIPTION, BLOWER
MOTOR............................24-22
RESISTOR - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-22
RESISTOR - INSTALLATION, BLOWER
MOTOR............................24-22
RESISTOR - OPERATION, BLOWER
MOTOR............................24-22
RESISTOR - REMOVAL, BLOWER
MOTOR............................24-22
RESTRAINT DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL......................8O-6
RESTRAINT SYSTEM - DIAGNOSIS AND
TESTING, SUPPLEMENTAL..............8O-6
RESTRAINT SYSTEM - WARNING........8O-5
RESTRAINTS - DESCRIPTION............8O-2
RESTRAINTS - OPERATION.............8O-4
RESTRAINTS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED
SUPPLEMENTAL......................8O-6
RETAINER/BULKHEAD - ASSEMBLY, 4C . . 21-123
RETAINER/BULKHEAD - DISASSEMBLY,
4C ...............................21-122
RETRACTOR - INSTALLATION, FRONT
SEAT BELT .........................8O-24
RETRACTOR - INSTALLATION, REAR
CENTER SEAT BELT..................8O-33
RETRACTOR - INSTALLATION, REAR
OUTBOARD SEAT BELT................8O-34
RETRACTOR - REMOVAL, FRONT SEAT
BELT ..............................8O-23
RETRACTOR - REMOVAL, REAR CENTER
SEAT BELT .........................8O-32
RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT BELT................8O-33
RETURN - DESCRIPTION, SENSOR.......8E-14
RETURN HOSE (GEAR TO THE COOLER)
- INSTALLATION.....................19-22
RETURN HOSE (GEAR TO THE COOLER)
- REMOVAL.........................19-21
RETURN HOSE (RESERVOIR TO THE
COOLER) - INSTALLATION.............19-22
RETURN HOSE (RESERVOIR TO THE
COOLER) - REMOVAL
.................19-21
REVERSE FLUSHING - STANDARD
PROCEDURE, COOLING SYSTEM
.........7-12
RFE TRANSMISSION, SPECIAL TOOLS
. . . 21-120
RHD - INSTALLATION
...............8W-97-6
RHD - REMOVAL
...................8W-97-5
RIGHT POWER SEAT SWITCH -
DESCRIPTION
.......................8N-19
RIGHT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING
.............8N-19
RIGHT POWER SEAT SWITCH -
INSTALLATION
......................8N-20
RIGHT POWER SEAT SWITCH -
OPERATION
.........................8N-19
RIGHT POWER SEAT SWITCH -
REMOVAL
..........................8N-20
RIGHT SIDE - INSTALLATION
........2-12,2-15
RIGHT SIDE - REMOVAL
............2-11,2-14
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE
...........3-112,3-82RING - REMOVAL, PINION GEAR/RING
GEAR/TONE.....................3-110,3-79
RING FITTING - STANDARD
PROCEDURE, PISTON..................9-52
RISER - INSTALLATION, MANUAL SEAT . . 23-168
RISER - REMOVAL, MANUAL SEAT......23-167
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-8
RKE TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE.........................8N-8
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE...............8N-9
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-2
ROAD TESTING - DIAGNOSIS AND
TESTING...........................21-78
ROCKER ARM - DESCRIPTION.......9-29,9-37
ROCKER ARM - INSTALLATION..........9-37
ROCKER ARM - REMOVAL..............9-37
ROD - DESCRIPTION, PISTON &
CONNECTING.........................9-49
ROD BEARING - FITTING - STANDARD
PROCEDURE, CONNECTING.............9-40
ROD BEARING, FITTING - CONNECTING....9-49
ROD END - INSTALLATION, TIE.........19-16
ROD END - REMOVAL, TIE.............19-16
ROD END REMOVAL TOOL, SPECIAL
TOOLS - OUTER TIE..................19-15
ROTATION - STANDARD PROCEDURE,
TIRE................................22-2
ROTOR - DIAGNOSIS AND TESTING,
DISC BRAKE.........................5-18
ROTOR - STANDARD PROCEDURE, DISC
BRAKE..............................5-19
ROTORS - INSTALLATION...............5-19
ROTORS - REMOVAL..................5-19
ROUTING 3.7L ENGINE - DESCRIPTION,
COOLING SYSTEM.....................7-2
RUN CHANNEL - INSTALLATION, GLASS . 23-123,
23-130
RUN CHANNEL - REMOVAL, GLASS....23-123,
23-130
RUNNING LAMP RELAY - DESCRIPTION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - INSTALLATION,
DAYTIME...........................8L-21
RUNNING LAMP RELAY - OPERATION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - REMOVAL,
DAYTIME...........................8L-21
RUNOUT - DIAGNOSIS AND TESTING,
TIRES AND WHEEL....................22-1
SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE..............Intro.-9
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD.......................23-173
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE..............23-163
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-4
SCHEMATICS AND DIAGRAMS -
HYDRAULIC SCHEMATICS.............21-100
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - HYDRAULIC.............21-100
SCUFF PLATE - INSTALLATION, DOOR
SILL..............................23-157
SCUFF PLATE - INSTALLATION, REAR
DOOR............................23-160
SCUFF PLATE - REMOVAL, DOOR SILL . . . 23-157
SCUFF PLATE - REMOVAL, REAR DOOR . . 23-160
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL.....................9-47
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL.....................9-46
SEAL - INSTALLATION, ADAPTER
HOUSING..........................21-124
SEAL - INSTALLATION, A-PILLAR.......23-185
SEAL - INSTALLATION, COWL/PLENUM . . 23-187
SEAL - INSTALLATION, COWL/PLENUM
WINDOW BAFFLE
...................23-187
SEAL - INSTALLATION, FRONT OUTPUT
SHAFT
......................21-208,21-246
SEAL - INSTALLATION, GLASS PANEL
. . . 23-178
SEAL - INSTALLATION, OIL PUMP
FRONT
............................21-152
SEAL - INSTALLATION, PINION
. . 3-103,3-39,3-68
22 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

TRANSCEIVER MODULE - DESCRIPTION,
INTRUSION.........................8Q-14
TRANSCEIVER MODULE -
INSTALLATION, INTRUSION............8Q-16
TRANSCEIVER MODULE - OPERATION,
INTRUSION.........................8Q-15
TRANSCEIVER MODULE - REMOVAL,
INTRUSION.........................8Q-15
TRANSFER CASE - NV231 - ASSEMBLY . . 21-194
TRANSFER CASE - NV231 - CLEANING . . 21-190
TRANSFER CASE - NV231 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV231 -
DESCRIPTION......................21-178
TRANSFER CASE - NV231 - DIAGNOSIS
AND TESTING......................21-180
TRANSFER CASE - NV231 -
DISASSEMBLY......................21-182
TRANSFER CASE - NV231 - INSPECTION . 21-190
TRANSFER CASE - NV231 -
INSTALLATION......................21-205
TRANSFER CASE - NV231 - OPERATION . 21-179
TRANSFER CASE - NV231 - REMOVAL . . . 21-181
TRANSFER CASE - NV242 - ASSEMBLY . . 21-230
TRANSFER CASE - NV242 - CLEANING . . 21-227
TRANSFER CASE - NV242 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV242 -
DESCRIPTION......................21-215
TRANSFER CASE - NV242 - DIAGNOSIS
AND TESTING......................21-216
TRANSFER CASE - NV242 -
DISASSEMBLY......................21-218
TRANSFER CASE - NV242 - INSPECTION . 21-228
TRANSFER CASE - NV242 -
INSTALLATION......................21-243
TRANSFER CASE - NV242 - OPERATION . 21-215
TRANSFER CASE - NV242 - REMOVAL . . . 21-217
TRANSFER CASE, NV231.............21-206
TRANSFER CASE, NV242.............21-244
TRANSFER CASE SKID PLATE -
INSTALLATION........................13-7
TRANSFER CASE SKID PLATE -
REMOVAL...........................13-7
TRANSFER CASE, SPECIFICATIONS -
NV242............................21-244
TRANSMISSION - 45RFE -
DESCRIPTION, AUTOMATIC.............21-76
TRANSMISSION - 45RFE - OPERATION,
AUTOMATIC.........................21-77
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-2
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC.................21-77
TRANSMISSION - DIAGNOSIS AND
TESTING, MANUAL...............21-2,21-33
TRANSMISSION CLUTCH OPERATION -
DIAGNOSIS AND TESTING, AIR
CHECKING..........................21-80
TRANSMISSION CONTROL MODULE -
DESCRIPTION.......................8E-18
TRANSMISSION CONTROL MODULE -
OPERATION.........................8E-18
TRANSMISSION CONTROL RELAY -
DESCRIPTION......................21-168
TRANSMISSION CONTROL RELAY -
OPERATION........................21-168
TRANSMISSION FILL - STANDARD
PROCEDURE.......................21-128
TRANSMISSION FLUID - DESCRIPTION,
AUTOMATIC...........................0-2
TRANSMISSION FLUID - OPERATION,
AUTOMATIC...........................0-4
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - INSTALLATION....8L-83
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - REMOVAL........8L-82
TRANSMISSION RANGE SENSOR -
DESCRIPTION
......................21-168
TRANSMISSION RANGE SENSOR -
OPERATION
........................21-168
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DESCRIPTION, BRAKE
.......21-124
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DIAGNOSIS AND TESTING,
BRAKE
............................21-125
TRANSMISSION SHIFT INTERLOCK
SYSTEM - OPERATION, BRAKE
.........21-125TRANSMISSION SOLENOID/TRS
ASSEMBLY - DESCRIPTION............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - INSTALLATION...........21-170
TRANSMISSION SOLENOID/TRS
ASSEMBLY - OPERATION.............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - REMOVAL...............21-170
TRANSMISSION, SPECIAL TOOLS - RFE . . 21-120
TRANSMISSION, SPECIFICATIONS......21-119
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION.....................21-170
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.......................21-170
TRANSMITTER - DESCRIPTION,
UNIVERSAL.........................8M-8
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY......8N-8
TRANSMITTER - DIAGNOSIS AND
TESTING, UNIVERSAL.................8M-8
TRANSMITTER - OPERATION,
UNIVERSAL.........................8M-8
TRANSMITTER - SPECIFICATIONS,
REMOTE KEYLESS ENTRY..............8N-9
TRANSMITTER BATTERIES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER CODES - STANDARD
PROCEDURE, ERASING................8M-8
TRANSMITTER CODES - STANDARD
PROCEDURE, SETTING.................8M-9
TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER PROGRAMING -
STANDARD PROCEDURE, RKE...........8N-9
TRANSPONDER KEY - DESCRIPTION.....8Q-18
TRANSPONDER KEY - OPERATION.......8Q-18
TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE, SENTRY KEY....8Q-8
TRAY - DESCRIPTION, BATTERY.........8F-21
TRAY - INSTALLATION, BATTERY........8F-21
TRAY - OPERATION, BATTERY..........8F-21
TRAY - REMOVAL, BATTERY............8F-21
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, B-PILLAR
LOWER...........................23-157
TRIM - INSTALLATION, B-PILLAR UPPER . 23-158
TRIM - REMOVAL, B-PILLAR LOWER....23-157
TRIM - REMOVAL, B-PILLAR UPPER....23-157
TRIM AND GRAB HANDLE -
INSTALLATION, A-PILLAR.............23-156
TRIM AND GRAB HANDLE - REMOVAL,
A-PILLAR..........................23-156
TRIM COVER - INSTALLATION, COWL . . . 23-157
TRIM COVER - REMOVAL, COWL.......23-157
TRIM LACE - INSTALLATION, OPENING . . 23-180
TRIM LACE - REMOVAL, OPENING......23-180
TRIM PANEL - INSTALLATION . . . 23-126,23-132,
23-138
TRIM PANEL - INSTALLATION, QUARTER . 23-159
TRIM PANEL - REMOVAL . 23-125,23-132,23-138
TRIM PANEL - REMOVAL, QUARTER....23-159
TRIP DEFINITION - DESCRIPTION........25-19
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TUBE - DESCRIPTION, A/C ORIFICE......24-50
TUBE - INSTALLATION, A/C ORIFICE......24-50
TUBE - INSTALLATION, DRAIN.........23-181
TUBE - OPERATION, A/C ORIFICE........24-50
TUBE - REMOVAL, A/C ORIFICE.........24-50
TUBE - REMOVAL, DRAIN.............23-180
TURN SIGNAL INDICATOR -
DESCRIPTION.......................8J-34
TURN SIGNAL INDICATOR - OPERATION . . 8J-34
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT.............8O-38
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT .........................8O-37
UNIT - ADJUSTMENT, FRONT FOG LAMP . . 8L-25
UNIT - ADJUSTMENT, HEADLAMP
.......8L-42
UNIT - DIAGNOSIS AND TESTING, FUEL
LEVEL SENDING
......................14-9
UNIT - INSTALLATION, ASH RECEIVER
LAMP
..............................8L-72
UNIT - INSTALLATION, CARGO LAMP
.....8L-74
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP
................8L-19UNIT - INSTALLATION, COURTESY LAMP . . 8L-77
UNIT - INSTALLATION, FRONT FOG
LAMP..............................8L-25
UNIT - INSTALLATION, FRONT LAMP.....8L-28
UNIT - INSTALLATION, HEADLAMP.......8L-42
UNIT - INSTALLATION, LICENSE PLATE
LAMP..............................8L-46
UNIT - INSTALLATION, READING LAMP . . . 8L-81
UNIT - INSTALLATION, REAR LAMP......8L-60
UNIT - INSTALLATION, REPEATER LAMP . . 8L-61
UNIT - REMOVAL, ASH RECEIVER LAMP . . 8L-72
UNIT - REMOVAL, CARGO LAMP........8L-74
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-19
UNIT - REMOVAL, COURTESY LAMP.....8L-76
UNIT - REMOVAL, FRONT FOG LAMP.....8L-25
UNIT - REMOVAL, FRONT LAMP.........8L-27
UNIT - REMOVAL, HEADLAMP..........8L-41
UNIT - REMOVAL, LICENSE PLATE LAMP . . 8L-45
UNIT - REMOVAL, READING LAMP.......8L-81
UNIT - REMOVAL, REAR LAMP..........8L-59
UNIT - REMOVAL, REPEATER LAMP......8L-60
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING.....................14-10
UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING......................14-9
UNIVERSAL JOINTS - ASSEMBLY,
SINGLE CARDAN.......................3-9
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN.......................3-8
UNIVERSAL TRANSMITTER -
DESCRIPTION........................8M-8
UNIVERSAL TRANSMITTER - DIAGNOSIS
AND TESTING........................8M-8
UNIVERSAL TRANSMITTER - OPERATION . . 8M-8
UNLOCK SWITCH - INSTALLATION,
DOOR LOCK.........................8N-5
UNLOCK SWITCH - REMOVAL, DOOR
LOCK...............................8N-4
UPPER BALL JOINT - INSTALLATION......2-20
UPPER BALL JOINT - REMOVAL..........2-20
UPPER CONTROL ARM - INSTALLATION . . . 2-21
UPPER CONTROL ARM - REMOVAL.......2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - DESCRIPTION.........2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - OPERATION..........2-20
UPPER TRIM - INSTALLATION, B-PILLAR . 23-158
UPPER TRIM - REMOVAL, B-PILLAR....23-157
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MIDTRONICS ELECTRICAL
TESTER - STANDARD PROCEDURE.......8F-15
V-6 - ENGINE FIRING ORDER, 3.7L........8I-2
V-6 - IGNITION COIL RESISTANCE, 3.7L....8I-3
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-28
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-28
VACUUM LINES - DESCRIPTION.........25-33
VACUUM RESERVOIR - DESCRIPTION.....8P-7
VACUUM RESERVOIR - DIAGNOSIS AND
TESTING............................8P-7
VACUUM RESERVOIR - INSTALLATION....8P-8
VACUUM RESERVOIR - OPERATION.......8P-7
VACUUM RESERVOIR - REMOVAL........8P-7
VACUUM SYSTEM - DIAGNOSIS AND
TESTING............................24-6
VALUE - DESCRIPTION, LOAD..........25-20
VALVE - DESCRIPTION, FLOW
MANAGEMENT.......................14-6
VALVE - DESCRIPTION, FRONT CHECK....8R-8
VALVE - DESCRIPTION, FUEL TANK
CHECK.............................14-28
VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - DESCRIPTION, PCV............25-29
VALVE - DESCRIPTION, REAR CHECK
....8R-34
VALVE - DESCRIPTION, SOLENOID
SWITCH
...........................21-161
VALVE - DESCRIPTION, VACUUM CHECK
. . 24-28
VALVE - DIAGNOSIS AND TESTING, PCV
. . 25-31
VALVE - DIAGNOSIS AND TESTING,
PROPORTIONING
.....................5-20
28 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

VALVE - INSTALLATION, FLOW
MANAGEMENT.......................14-7
VALVE - INSTALLATION, FRONT CHECK....8R-9
VALVE - INSTALLATION, FUEL TANK
CHECK.............................14-28
VALVE - INSTALLATION, PCV...........25-32
VALVE - INSTALLATION, REAR CHECK....8R-35
VALVE - INSTALLATION, VACUUM CHECK . 24-28
VALVE - OPERATION, FLOW
MANAGEMENT.......................14-6
VALVE - OPERATION, FRONT CHECK......8R-9
VALVE - OPERATION, FUEL TANK CHECK . . 14-28
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - OPERATION, PCV..............25-31
VALVE - OPERATION, REAR CHECK......8R-34
VALVE - OPERATION, SOLENOID SWITCH . 21-161
VALVE - OPERATION, VACUUM CHECK....24-28
VALVE - REMOVAL, FLOW
MANAGEMENT.......................14-6
VALVE - REMOVAL, FRONT CHECK.......8R-9
VALVE - REMOVAL, FUEL TANK CHECK . . . 14-28
VALVE - REMOVAL, PCV...............25-32
VALVE - REMOVAL, REAR CHECK.......8R-34
VALVE - REMOVAL, VACUUM CHECK.....24-28
VALVE BODY - ASSEMBLY............21-176
VALVE BODY - CLEANING.............21-175
VALVE BODY - DESCRIPTION............21-171
VALVE BODY - DISASSEMBLY..........21-173
VALVE BODY - INSPECTION...........21-175
VALVE BODY - INSTALLATION..........21-177
VALVE BODY - OPERATION............21-171
VALVE BODY - REMOVAL.............21-172
VALVE GUIDE SEALS - DESCRIPTION . . 9-29,9-38
VALVE GUIDES - DESCRIPTION......9-19,9-30
VALVE SPRINGS - DESCRIPTION.....9-29,9-38
VALVE SPRINGS - INSTALLATION.....9-29,9-38
VALVE SPRINGS - REMOVAL........9-29,9-38
VALVE TIMING - DESCRIPTION...........9-71
VALVE TIMING - OPERATION............9-71
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST.................9-28,9-36
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST.................9-27,9-35
VANITY LAMP BULB - INSTALLATION.....8L-84
VANITY LAMP BULB - REMOVAL........8L-83
VAPOR CANISTER - DESCRIPTION.......25-33
VAPOR CANISTER - INSTALLATION......25-33
VAPOR CANISTER - OPERATION.........25-33
VAPOR CANISTER - REMOVAL..........25-33
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-3
VEHICLE EMISSION CONTROL
INFORMATION (VECI) LABEL -
DESCRIPTION......................Intro.-8
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-8
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION.....................Intro.-9
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-3
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-6
VERIFICATION TEST - STANDARD
PROCEDURE.........................8O-8
VIBRATION - DIAGNOSIS AND TESTING,
TIRE NOISE OR.......................22-8
VIBRATION DAMPER - INSTALLATION.....9-55
VIBRATION DAMPER - REMOVAL.........9-54
VIEW MIRROR - INSTALLATION, SIDE . . . 23-145
VIEW MIRROR - REMOVAL, REAR......23-161
VIEW MIRROR - REMOVAL, SIDE.......23-145
VISCOUS - CLEANING, RADIATOR - FAN . . . 7-29
VISCOUS - DESCRIPTION, RADIATOR -
FAN ................................7-27
VISCOUS - INSPECTION, RADIATOR -
FAN ................................7-29
VISCOUS - INSTALLATION, RADIATOR -
FAN
................................7-29
VISCOUS - OPERATION, RADIATOR -
FAN
................................7-27
VISCOUS - REMOVAL, RADIATOR - FAN
....7-28
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING
............................7-28
VISOR - INSTALLATION, SUN
..........23-160VISOR - REMOVAL, SUN..............23-160
VISOR SUPPORT - INSTALLATION, SUN . . 23-160
VISOR SUPPORT - REMOVAL, SUN.....23-160
VOLT SUPPLIES - DESCRIPTION, 5......8E-13
VOLT SUPPLIES - OPERATION, 5........8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION....8F-31
VOLTAGE REGULATOR - OPERATION.....8F-31
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-12
VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-148
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-35
WAIT-TO-START INDICATOR -
OPERATION.........................8J-35
WARNING - INSTALLATION............23-173
WARNING - REMOVAL...............23-173
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-39
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-173
WARNING, BRAKES - BASE..............5-2
WARNING, CLUTCH.....................6-2
WARNING, FRONT......................2-7
WARNING, REAR......................2-16
WARNING, RESTRAINT SYSTEM.........8O-5
WARNING SYSTEM - DESCRIPTION,
CHIME..............................8B-1
WARNING SYSTEM - DIAGNOSIS AND
TESTING, CHIME......................8B-6
WARNING SYSTEM - OPERATION,
CHIME..............................8B-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-39
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-35
WASHER FLUID INDICATOR -
DIAGNOSIS AND TESTING..............8J-36
WASHER FLUID INDICATOR -
OPERATION.........................8J-36
WASHER FLUID LEVEL SWITCH -
DESCRIPTION.......................8R-17
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-18
WASHER FLUID LEVEL SWITCH -
OPERATION.........................8R-17
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-17
WASHER HOSES/TUBES - DESCRIPTION,
FRONT.............................8R-10
WASHER HOSES/TUBES - DESCRIPTION,
REAR..............................8R-35
WASHER HOSES/TUBES - OPERATION,
FRONT.............................8R-10
WASHER HOSES/TUBES - OPERATION,
REAR..............................8R-36
WASHER NOZZLE - DESCRIPTION,
FRONT.............................8R-11
WASHER NOZZLE - DESCRIPTION, REAR . 8R-36
WASHER NOZZLE - INSTALLATION,
FRONT.............................8R-11
WASHER NOZZLE - INSTALLATION,
REAR..............................8R-37
WASHER NOZZLE - OPERATION, FRONT . . 8R-11
WASHER NOZZLE - OPERATION, REAR . . . 8R-36
WASHER NOZZLE - REMOVAL, FRONT....8R-11
WASHER NOZZLE - REMOVAL, REAR....8R-36
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-18
WASHER PUMP/MOTOR - INSTALLATION . 8R-20
WASHER PUMP/MOTOR - OPERATION . . . 8R-19
WASHER PUMP/MOTOR - REMOVAL.....8R-19
WASHER RESERVOIR - DESCRIPTION....8R-21
WASHER RESERVOIR - INSTALLATION . . . 8R-22
WASHER RESERVOIR - OPERATION
......8R-21
WASHER RESERVOIR - REMOVAL
.......8R-21
WASHER SYSTEM - CLEANING, FRONT
WIPER
..............................8R-7
WASHER SYSTEM - CLEANING, REAR
WIPER
.............................8R-32
WASHER SYSTEM - DIAGNOSIS AND
TESTING, FRONT WIPER
...............8R-6WASHER SYSTEM - DIAGNOSIS AND
TESTING, REAR WIPER...............8R-30
WASHER SYSTEM - INSPECTION, FRONT
WIPER..............................8R-7
WASHER SYSTEM - INSPECTION, REAR
WIPER.............................8R-33
WATER DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING . . 23-176
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - DESCRIPTION...........7-29
WATER PUMP - OPERATION.............7-30
WATERDAM - INSTALLATION....23-126,23-133
WATERDAM - REMOVAL........23-126,23-133
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-37
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-37
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-8
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-71
WEATHERSTRIP - INSTALLATION, COWL . 23-185
WEATHERSTRIP - INSTALLATION, DOOR
LOWER...........................23-186
WEATHERSTRIP - INSTALLATION, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - INSTALLATION,
SWING GATE BELTLINE...............23-186
WEATHERSTRIP - INSTALLATION,
SWING GATE OPENING...............23-186
WEATHERSTRIP - REMOVAL, COWL.....23-185
WEATHERSTRIP - REMOVAL, DOOR
LOWER...........................23-186
WEATHERSTRIP - REMOVAL, DOOR
PRIMARY..........................23-185
WEATHERSTRIP - REMOVAL, SWING
GATE BELTLINE.....................23-186
WEATHERSTRIP - REMOVAL, SWING
GATE OPENING.....................23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE RAIL............23-186
WEATHERSTRIP/RETAINER -
INSTALLATION, WINDSHIELD A-PILLAR . . 23-187
WEATHERSTRIP/RETAINER - REMOVAL,
SIDE RAIL.........................23-186
WEATHERSTRIP/RETAINER - REMOVAL,
WINDSHIELD A-PILLAR...............23-186
WELD AND STRUCTURAL ADHESIVE
LOCATIONS - SPECIFICATIONS...........23-9
WHEEL - INSTALLATION, STEERING......19-12
WHEEL - REMOVAL, STEERING.........19-12
WHEEL ALIGNMENT - DESCRIPTION.......2-3
WHEEL ALIGNMENT - OPERATION.........2-3
WHEEL BALANCING - STANDARD
PROCEDURE.........................22-4
WHEEL CYLINDERS - ASSEMBLY.........5-29
WHEEL CYLINDERS - CLEANING.........5-28
WHEEL CYLINDERS - DISASSEMBLY......5-28
WHEEL CYLINDERS - INSPECTION........5-29
WHEEL CYLINDERS - INSTALLATION......5-29
WHEEL CYLINDERS - REMOVAL..........5-28
WHEEL MOUNTING - STANDARD
PROCEDURE........................22-10
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, FRONT...............23-145
WHEEL OPENING FLARE MOLDINGS -
INSTALLATION, REAR................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, FRONT...................23-145
WHEEL OPENING FLARE MOLDINGS -
REMOVAL, REAR....................23-145
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-10
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRES......................22-1
WHEEL SPEED SENSOR -
INSTALLATION, FRONT
.................5-34
WHEEL SPEED SENSOR -
INSTALLATION, REAR
..................5-35
WHEEL SPEED SENSOR - REMOVAL,
FRONT
..............................5-34
WHEEL SPEED SENSOR - REMOVAL,
REAR
...............................5-35
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT
...............23-143
KJINDEX 29
Description Group-Page Description Group-Page Description Group-Page