
6A±14
ENGINE MECHANICAL (6VE1 3.5L)
Abnormal Combustion
ConditionPossible causeCorrection
Trouble in fuel systemFuel pressure control valve defectiveReplace
Fuel filter cloggedReplace
Fuel pump cloggedClean or replace
Fuel tank or fuel pipe cloggedClean or replace
Fuel injector cloggedClean or replace
Fuel pump relay defectiveReplace
Power supply cable for fuel pump
broken or poor connectionsReconnect, correct or replace
Mass Airflow (MAF) Sensor circuit
open or defectiveCorrect or replace
MAF Sensor defectiveReplace
Manifold Absolute Pressure Sensor
circuit open or shortedCorrect or replace
Manifold Absolute Pressure Sensor
defectiveReplace
Engine Coolant Temperature (ECT)
Sensor circuit open or shortedCorrect or replace
ECT Sensor defectiveReplace
Throttle Position Sensor adjustment
incorrectReadjust
Throttle Position Sensor defectiveReplace
Throttle Position Sensor connector
poor connectionsReconnect
Vehicle Speed Sensor cable poor
connections or defectiveCorrect or replace
Vehicle Speed Sensor loosely fixedFix tightly
Vehicle Speed Sensor in wrong
contact or defectiveReplace
Powertrain Control Module cable
poor connections or defectiveCorrect or replace
Trouble in emission control systemHeated Oxygen Sensor circuit openCorrect or replace
Heated Oxygen Sensor defectiveReplace
Signal vacuum hose loosely fitted or
defectiveCorrect or replace
EGR Valve circuit open or shortedCorrect or replace
Exhaust Gas Recirculation Valve
defectiveReplace
ECT Sensor circuit open or shortedCorrect or replace
Canister Purge Valve circuit open or
shortedCorrect or replace
Canister Purge Valve defectiveReplace
ECT Sensor defectiveReplace
Positive Crankcase Ventilation
(PCV) valve and hose cloggedCorrect or replace
Evaporator systemRefer to Section 6E
Trouble in ignition systemÐÐÐÐRefer to ªEngine Lacks Powerº

6A±17
ENGINE MECHANICAL (6VE1 3.5L)
Fuel Consumption Excessive
ConditionPossible causeCorrection
Trouble in fuel systemMixture too rich or too lean due to
trouble in fuel injection systemRefer to ªAbnormal Combustionº
Fuel cut function does not workRefer to ªAbnormal Combustionº
Trouble in ignition systemMisfiring or abnormal combustion
due to trouble in ignition systemRefer to ªHard Startº or ªAbnormal
Combustionº
OthersEngine idle speed too highReset Idle Air Control Valve
Fuel system leakageCorrect or replace
Clutch slippingCorrect
Brake dragCorrect
Selection of transmission gear
incorrectCaution operator of incorrect gear
selection
Excessive Exhaust Gas
Recirculation flow due to trouble in
Exhaust Gas Recirculation systemRefer to ªAbnormal Combustionº
Lubrication Problems
ConditionPossible causeCorrection
Oil pressure too lowWrong oil in useReplace with correct engine oil
Relief valve stickingReplace
Oil pump not operating properlyCorrect or replace
Oil pump strainer cloggedClean or replace strainer
Oil pump wornReplace
Oil pressure gauge defectiveCorrect or replace
Crankshaft bearing or connecting
rod bearing wornReplace
Oil contaminationWrong oil in useReplace with correct engine oil
Oil filter cloggedReplace oil filter
Cylinder head gasket damageReplace gasket
Burned gases leakingReplace piston and piston rings or
cylinder body assembly
Oil not reaching valve systemOil passage in cylinder head or
cylinder body cloggedClean or correct
Engine Oil Pressure Check
1. Check for dirt, gasoline or water in the engine oil.
a. Check the viscosity of the oil.
b. Check the viscosity of the oil.
c. Change the oil if the viscosity is outside the
specified standard.
d. Refer to the ªMaintenance and Lubricationº section
of this manual.
2. Check the engine oil level.
The level should fall somewhere between the ªADDº
and the ªFULLº marks on the oil level dipstick.
If the oil level does not reach the ªADDº mark on the
oil level dipstick, engine oil must be added.3. Remove the oil pressure unit.
4. Install an oil pressure gauge.
5. Start the engine and allow the engine to reach normal
operating temperature (About 80C).
6. Measure the oil pressure.
Oil pressure should be:
392±550 kPa (56.9±80.4 psi) at 3000 rpm.
7. Stop the engine.
8. Remove the oil pressure gauge.
9. Install the oil pressure unit.
10. Start the engine and check for leaks.

6C±1 ENGINE FUEL (6VE1 3.5L)
AXIOM
ENGINE
ENGINE FUEL
CONTENTS
Service Precaution 6C±1. . . . . . . . . . . . . . . . . . . . . .
General Description 6C±2. . . . . . . . . . . . . . . . . . . . .
Fuel Metering 6C±3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Filter 6C±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 6C±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 6C±4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 6C±5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 6C±5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
In±Tank Fuel Filter 6C±5. . . . . . . . . . . . . . . . . . . . .
Fuel Pump Flow Test 6C±5. . . . . . . . . . . . . . . . . . .
Fuel Pump 6C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump and Associated Parts 6C±6. . . . . . . .
Removal 6C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 6C±7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Tube / Quick ± Connector Fittings 6C±8. . . . .
Precautions 6C±8. . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions During Work 6C±8. . . . . . . . . . . . . . . . . . Removal 6C±8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reuse of Quick±Connector 6C±9. . . . . . . . . . . . .
Assembling Advice 6C±9. . . . . . . . . . . . . . . . . . . .
Fuel Pump Relay 6C±10. . . . . . . . . . . . . . . . . . . . . . . .
General Description 6C±10. . . . . . . . . . . . . . . . . . . .
Fuel Tank 6C±10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Tank and Associated Parts 6C±10. . . . . . . . .
Removal 6C±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 6C±11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Gauge Unit 6C±12. . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation 6C±12. . . . . . . . . . . . . . .
Fuel Filler Cap 6C±12. . . . . . . . . . . . . . . . . . . . . . . . . .
General Description 6C±12. . . . . . . . . . . . . . . . . . . .
Inspection 6C±12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 6C±13. . . . . . . . . . . . .
Special Tool 6C±13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.

6C±2
ENGINE FUEL (6VE1 3.5L)
General Description
140R200004
Legend
(1) Fuel Filler Cap
(2) Fuel Tank
(3) Rollover Valve
(4) Fuel Pump and Sender Assembly
(5) Fuel Filter
(6) Fuel Rail Right
(7) Right Bank
(8) Fuel Rail Left
(9) Left Bank(10) Fuel Pressure Control Valve
(11) Common Chamber
(12) Duty Solenoid Valve
(13) Throttle Valve
(14) Canister
(15) Vent Hose
(16) Vent Solenoid Valve
(17) Separator
(18) Shut off Valve (With Over Pressure Relief
Valve)

6C±4
ENGINE FUEL (6VE1 3.5L)
Fuel Filter
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system
for loose connection or leakage. For the fuel system
diagnosis, see Section ªDriveability and Emissionº.
1. Disconnect battery ground cable.
2. Remove Fuel filler cap(1).
140R100023
Legend
(1) Fuel Filler Cap
(2) Receive Rubber Drain
3. Disconnect fuel hoses(1) from fuel filter on both
engine side and fuel tank side.
4. Fuel filter fixing bolt(2).
Remove the fuel filter fixing bolt(2) on fuel filter
holder.5. Remove fuel filter(3).
041RW003
Legend
(1) Fuel Hose
(2) Fuel Filter Fixing Bolt
(3) Fuel Filter
Inspection
1. Replace the fuel filter if the fuel leaks from fuel filter
body or if the fuel filter body itself is damaged.
2. Replace the filter if it is clogged with dirt or sediment.
3. Check clogged drain port of the receive rubber by the
foreign material, repair or clear if found clog it.

6C±5 ENGINE FUEL (6VE1 3.5L)
Installation
1. Install the fuel filter in the proper direction.
2. Install fuel filter holder fixing bolt.
3. Connect fuel hoses on engine side(1) and fuel tank
side(2).
041RW001
4. Install fuel filler cap
5. Connect the battery ground cable.
Inspection
After installation, start engine and check for fuel leakage.
In±Tank Fuel Filter
The filter is located on the lower end of fuel pickup tube in
the fuel tank. The fuel filter prevents dirt and water the fuel
system not unless the filter is submerged in water. The
fuel filter is maintenance free, that requires no
maintenance. Excess water and sediment in the tank
restricts fuel supply to the engine, resulting in engine stall.
If this happens, the fuel tank would need to be cleaned
thoroughly.
Fuel Pump Flow Test
If reduction of fuel supply is suspected, perform the
following checks.
1. Make sure that there is fuel in the tank.
2. With the engine running, check the fuel feed pipe and
hose from fuel tank to injector for evidence of
leakage. Retighten, if pipe or hose connection is
loose. Also, inspect bent or kink fuel pipes and hoses.
3. Insert the hose from fuel feed pipe into a clean
container, and check for fuel pump flow rate.
4. Connect the pump relay terminals with a jumper
wire(1) as shown and start the fuel pump to measure
delivery.
140R200003
CAUTION: Never generate sparks when connecting
a jumper wire.
Delivery Times
Delivery
15 seconds0.38 liters minimum
If the measure value is out of standard, conduct the
pressure test.
Pressure test
For the pressure test to the fuel system, see Section 6E
ªFuel Control Systemº.

6C±11 ENGINE FUEL (6VE1 3.5L)
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system
for loose connection or leakage. For the fuel system
diagnosis, see Section ªDriveability and Emissionº.
1. Drain the fuel from the fuel tank, refer to the ªFuel
Pump Flow Testº in this section.
2. Disconnect battery ground cable.
3. Loosen fuel filler cap to reduce the pressure in fuel
tank.
4. Support underneath of the fuel tank assembly (1) with
a lifter.
5. Disconnect fuel feed hose (7) and fuel return hose (8)
near the fuel filter.
NOTE: Plug both ends of the fuel hoses to prevent fuel
leakage.
6. Disconnect fuel filler hose (5) and fuel vent hose (6) at
the fuel filler neck.
NOTE: Cover fuel hoses to prevent any dust entering.
7. Remove two bolts (4) and remove separator.
8. Remove the five fuel tank assembly fixing bolts (2)
and one nut (3).
9. Lower the tank and disconnect the wiring connectors
(9, 10).
Installation
1. Raise the fuel tank assembly (1) and connect the
wiring connectors (9, 10).
2. Install fuel tank assembly along with protectors and
tighten the five fixing bolts (2) and one nut (3) to the
specified torque.
Torque: 68 N´m (50 lb ft)
3. Install the separator and tighten two bolts (4).
Torque: 10 N´m (95 lb in)
4. Connect fuel filler hose (5) and fuel vent hose and clip
them firmly.
5. Connect fuel feed hose (7) and fuel return hose(8),
and clip them firmly.
6. Tighten fuel filler cap until at least three clicks are
heard.
7. Connect battery ground cable.

6E±4
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
DTC P1107 MAP Circuit Intermittent Low
Voltage 6E±386. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D T C P 1111 I AT Sensor Circuit Intermittent
High Voltage 6E±388. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1112 IAT Sensor Circuit Intermittent
Low Voltage 6E±391. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1114 ECT Sensor Circuit Intermittent
Low Voltage 6E±393. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1115 ECT Sensor Circuit Intermittent
High Voltage 6E±395. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code(DTC)P1120-TPS 1
Throttle Position Sensor (TPS1) Output
Abnormal 6E±398. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1125 ETC (Electric Throttle Control)
Limit Performance Mode 6E±401. . . . . . . . . . . . . . . . .
DTC P1133 HO2S Insufficient Switching
Bank 1 Sensor 1 6E±404. . . . . . . . . . . . . . . . . . . . . . . .
DTC P1134 HO2S Transition Time Ratio
Bank 1 Sensor 1 6E±408. . . . . . . . . . . . . . . . . . . . . . . .
DTC P1153 HO2S Insufficient Switching
Bank 2 Sensor 1 6E±412. . . . . . . . . . . . . . . . . . . . . . . .
DTC P1154 HO2S Circuit Transition Time
Ratio Bank 2 Sensor 1 6E±416. . . . . . . . . . . . . . . . . .
DTC P1167 Fuel System Rich During Decel
Fuel Cut Off (Bank 1) 6E±420. . . . . . . . . . . . . . . . . . . .
DTC P1169 Fuel System Rich During Decel
Fuel Cut Off (Bank 2) 6E±422. . . . . . . . . . . . . . . . . . . .
DTC P1171 Fuel System Lean During
Acceleration 6E±424. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1220 Throttle Position Senser2
(TPS2) Circuit Fault 6E±427. . . . . . . . . . . . . . . . . . . . .
DTC P1221 TPS1 ± TPS2 Correlation
(Circuit Performance) 6E±430. . . . . . . . . . . . . . . . . . .
DTC P1271 APS 1± 2 Correlation Error 6E±433. . .
DTC P1272 APS 2 ± 3 Correlation Error 6E±436. . .
DTC P1273 APS 1 ± 3 Correlation Error 6E±439. . . .
DTC P1275 APS 1 Output Fault 6E±442. . . . . . . . . . .
DTC P1280 APS 2 Output Fault 6E±444. . . . . . . . . . .
DTC P1285 APS 3 Output Fault 6E±446. . . . . . . . . . .
DTC P1290 ETC Forced Idle Mode 6E±448. . . . . . . .
DTC P1295 ETC Power Management Mode 6E±451
DTC P1299 ETC Forced Engine Shutdown
Mode 6E±455. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1310 ION Sensing Module Diagnosis 6E±459
DTC P1311 ION Sensing Module SEC
Line 1 Circuit Fault 6E±462. . . . . . . . . . . . . . . . . . . . . .
DTC P1312 ION Sensing Module SEC
Line 2 Circuit Fault 6E±465. . . . . . . . . . . . . . . . . . . . . .
DTC P1326 ION Sensing Module Combustion
Quality Input Circuit Fault 6E±468. . . . . . . . . . . . . . . .
DTC P1340 ION Sensing Module Cylinder ID
Fault (Cylinder Synchronization Fail) 6E±471. . . . . .
DTC P1404 EGR Stuck Closed 6E±474. . . . . . . . . . .
DTC P1441 EVAP System Flow During
Non-Purge 6E±477. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1514 TPS - MAF Correlation Error 6E±480. . . DTC P1515 Command - Actual TPS
Correlation Error 6E±484. . . . . . . . . . . . . . . . . . . . . . . .
DTC P1516 Command - Actual TPS
Correlation Error 6E±487. . . . . . . . . . . . . . . . . . . . . . . .
DTC P1523 Actuator Control Return
Performance 6E±490. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1571 Brake Switch No Operation 6E±493. . . .
DTC P1625 PCM Unexpected Reset 6E±495. . . . . . .
DTC P1635 Reference Voltage # 1 Circuit
Fault 6E±496. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1639 Reference Voltage # 2 Circuit
Fault 6E±498. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1640 Driver-1-Output Circuit Fault
(ODM) 6E±500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1650 Quad Driver Module ªAº Fault 6E±503. .
Symptom Diagnosis 6E±506. . . . . . . . . . . . . . . . . . . . .
Default Matrix Table 6E±535. . . . . . . . . . . . . . . . . . . . .
On Vehicle Service
Crankshaft Position (CKP) Sensor 6E±538. . . . . . . . .
Engine Coolant Temperature (ECT) Sensor 6E±538.
Heated Oxygen Sensor (HO2S) 6E±539. . . . . . . . . . .
Intake Air Temperature (IAT) Sensor 6E±542. . . . . . .
ION Sensing Module 6E±542. . . . . . . . . . . . . . . . . . . . .
Mass Air Flow (MAF) Sensor 6E±543. . . . . . . . . . . . .
Manifold Absolute Pressure (MAP) Sensor 6E±544.
Malfunction Indicator Lamp (MIL) 6E±545. . . . . . . . . .
Reduced Power Lamp 6E±545. . . . . . . . . . . . . . . . . . .
Powertrain Control Module (PCM) 6E±545. . . . . . . . .
Service Precaution 6E±545. . . . . . . . . . . . . . . . . . . .
EEPROM 6E±547. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Position (TP) Sensor 6E±547. . . . . . . . . . . . .
Vehicle Speed Sensor (VSS) 6E±548. . . . . . . . . . . . .
Air Cleaner/Air Filter 6E±549. . . . . . . . . . . . . . . . . . . . .
Common Chamber 6E±549. . . . . . . . . . . . . . . . . . . . . .
Accelerator Pedal Replacement 6E±550. . . . . . . . . . .
Accelerator Position Sensor Replacement 6E±551. .
Accelerator Position Sensor Adjustment 6E±551. . . .
Fuel Filler Cap 6E±552. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Filter 6E±552. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Gauge Unit 6E±553. . . . . . . . . . . . . . . . . . . . . . . .
Fuel Injectors 6E±554. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Metering System 6E±555. . . . . . . . . . . . . . . . . . . .
Fuel Pump Assembly 6E±555. . . . . . . . . . . . . . . . . . . .
Fuel Pump Relay 6E±556. . . . . . . . . . . . . . . . . . . . . . . .
Fuel Rail Assembly 6E±557. . . . . . . . . . . . . . . . . . . . . .
Fuel Tank 6E±558. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body (TB) 6E±558. . . . . . . . . . . . . . . . . . . . . . .
Electronic Ignition System 6E±560. . . . . . . . . . . . . . . .
Catalytic Converter 6E±561. . . . . . . . . . . . . . . . . . . . . .
Air Conditioning Thermo Relay 6E±561. . . . . . . . . . .
EVAP Canister Hoses 6E±561. . . . . . . . . . . . . . . . . . . .
EVAP Canister 6E±562. . . . . . . . . . . . . . . . . . . . . . . . . .
EVAP Canister Vent Solenoid 6E±562. . . . . . . . . . . . .