2002 ISUZU AXIOM suspension

3D±36REAR SUSPENSION
Special Tools
ILLUSTRATIONTOOL NO.
TOOL NAME
J±39214
Remover and Installer;
Trailing link bushing
J±43008
Remover and Installer;
Upper link bushing
J±39792
Remover and Installer;
Lateral rod bushing
(Axle side)
J±39215
Remover and Installer;
Lateral rod bushing
(Frame side)

WHEEL AND TIRE SYSTEM3E±1
AXIOM
SUSPENSION
WHEEL AND TIRE SYSTEM
CONTENTS
Service Precaution 3E±1. . . . . . . . . . . . . . . . . . . . . .
General Description 3E±2. . . . . . . . . . . . . . . . . . . . .
Diagnosis 3E±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel 3E±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel and Associated Parts 3E±11. . . . . . . . . . . .
Removal 3E±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 3E±11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire 3E±12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire Replacement 3E±12. . . . . . . . . . . . . . . . . . . . . .
General Balance Procedure 3E±12. . . . . . . . . . . . . .
Balancing Wheel and Tire 3E±13. . . . . . . . . . . . . . . .
Main Data and Specifications 3E±14. . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.

WHEEL AND TIRE SYSTEM3E±3
Diagnosis
ConditionPossible causeCorrection
Vehicle PullsMismatched or uneven tires.Replace tire.
Tires not adequately inflated.Adjust tire pressure.
Broken or sagging springs.Replace spring.
Radial tire lateral force.Replace tire.
Improper wheel alignment.Adjust wheel alignment.
Brake dragging in one wheel.Repair brake.
Loose, bent or broken front or rear
suspension parts.Tighten or replace the appropriate
suspension part(s).
Faulty shock absorbers.Replace shock absorber.
Parts in power steering valve
defective.Replace power steering unit.
Abnormal or Excessive Tire WearSagging or broken spring.Replace spring.
Tire out of balance.Balance or replace tire.
Improper wheel alignment.Check front end alignment.
Faulty shock absorber.Replace shock absorber.
Hard driving.Replace tire.
Overloaded vehicle.Replace tire and reduce load.
Tires not rotated periodically.Replace or rotate tire.
Worn or loose road wheel bearings.Replace wheel bearing.
Wobbly wheel or tires.Replace wheel or tire.
Tires not adequately inflated.Adjust the pressure.
Wheel HopBlister or bump on tire.Replace tire.
Improper shock absorber operation.Replace shock absorber.
Shimmy, Shake or VibrationTire or wheel out of balance.Balance wheels or replace tire/or
wheel.
Loose wheel bearings.Replace wheel bearing.
Worn steering linkage ball joints.Replace ball joints.
Worn upper or lower end ball joints.Replace ball joints.
Excessive wheel runout.Repair or replace wheel and/or tire.
Blister or bump on tire.Replace tire.
Excessive loaded radial runout of
tire/wheel assembly.Replace tire or wheel.
Improper wheel alignment.Check wheel alignment.
Loose or worn steering linkage.Tighten or replace steering linkage.
Loose steering unit.Tighten steering unit.
Tires not adequately inflated.Adjust tire pressure.
Loose, bent or broken front or rear
suspension parts.Tighten or replace the appropriate
suspension parts.
Faulty shock absorber.Replace shock absorber.
Hub bearing preload misadjustment.Adjust preload.
Parts in power steering valve
defective.Replace power steering unit.

3E±4WHEEL AND TIRE SYSTEM
Condition CorrectionPossible cause
Hard SteeringBind in steering linkage ball studs,
upper or lower ball joint.Replace ball joint.
Improper wheel alignment.Check wheel alignment.
Tire not adequately inflated.Inflate tires to proper pressure.
Bind in steering column or shaft.Repair or replace.
Improper power steering system
operation.Repair or replace. Refer to Steering
section.
Too Much Play In SteeringWheel bearings worn.Replace wheel bearings.
Loose steering unit or linkage.Retighten or repair.
Worn or loose steering shaft
universal joint.Retighten or replace steering shaft.
Worn steering linkage ball joints.Replace ball joints.
Worn upper or lower end ball joints.Replace ball joints.
Poor Steering Wheel ReturnabilityBind in steering linkage ball joints.Replace ball joints.
Bind in upper or lower ball joints.Replace ball joints.
Bind in steering column and shaft.Repair or replace.
Bind in steering gear.Check and repair steering gear.
Improper wheel alignment.Adjust wheel alignment.
Tires not adequately inflated.Adjust pressure.
Loose steering wheel nut.Retighten.
Worn wheel bearing.Replace.
Abnormal NoiseWorn, sticky or loose upper or lower
ball joint, steering linkage ball joints
or drive axle joints.Replace.
Faulty shock absorbers.Replace.
Worn upper or lower control arm
bushing.Replace.
Loose stabilizer bar.Retighten bolts or replace bushings.
Loose wheel nuts.Tighten nuts. Check for elongated
wheel nut holes. Replace wheel if
required.
Loose suspension bolts or nuts.Retighten suspension bolts or nuts.
Broken or otherwise damaged wheel
bearings.Replace wheel bearing.
Broken suspension springs. Replace spring.
Loose steering unit. Retighten mounting bolt.
Faulty steering unit.Replace steering unit.
Wandering or Poor Steering StabilityMismatched or unevenly worn tires.Replace tire or inflate tires to proper
pressure.
Loose steering linkage ball joints.Replace ball joints.
Faulty shock absorbers.Replace shock absorber.
Loose stabilizer bar.Tighten or replace stabilizer bar or
bushings.
Broken or sagging springs.Replace spring (pairs).
Improper wheel alignment.Adjust wheel alignment.

WHEEL AND TIRE SYSTEM3E±5
Condition CorrectionPossible cause
Erratic Steering When BrakingWorn wheel bearings.Replace wheel bearings.
Broken or sagging springs.Replace spring (pairs).
Leaking caliper.Repair or replace caliper.
Warped discs.Replace brake disc.
Badly worn brake pads.Replace brake pads.
Tires are inflated unequally.Inflate tires to proper pressure.
Low or Uneven Trim HeightBroken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Incorrect springs.Adjust or replace torsion bar.
Suspension BottomsVehicle overloaded. Reduce load.
Faulty shock absorber.Replace shock absorber.
Incorrect, broken or sagging springs.Replace springs.
Body LeansLoose stabilizer bar.Tighten stabilizer bar bolts or replace
bushings.
Faulty shock absorber, struts or
mounting.Replace shock absorber.
Broken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Cupped TiresWorn wheel bearings.Replace wheel bearing.
Excessive tire or wheel run out.Replace tire or wheel.
Worn ball joints.Replace ball joints.
Tire out of balance.Adjust tire balance.
Irregular and Premature Wear
480RS001
Irregular and/or premature wear has many causes.
Some of them are incorrect inflation pressures, lack of tire
rotation, poor driving habits or improper wheel alignment.
Incorrect inflation is common cause of tire premature
wear.NOTE: Due to their design, radial tires tend to wear faster
in the shoulder area, particularly on the front tires. This
makes regular rotation especially necessary. After
rotation, be sure to check wheel nut torque, and set tire
pressures.

3E±8WHEEL AND TIRE SYSTEM
Radial Tire Lead/Pull Correction Chart
StepActionYe sNo
11. Inflate tires to recommended pressure.
2. Road test vehicle on level uncrowned road.
Was a problem corrected?
End.Go to Step 2
2Switch front tires side to side and road test again.
Was a problem corrected?If roughness
results,replace
tires.
Go to Step 3
3Did the vehicle lead in same direction?Go to Step 4 Go to Step 5
4Put tires back in original position and check alignment.
Was a problem corrected?
End.Go to Step 5
5Install known good tire on one front side.
Was a problem corrected?
Replace tire.
Install a known
good tire in place
of other front tire.
If lead corrected,
replace tire.
Typical examples of abnormal tire ahead wear and major
causes:
CAUTION: Similar wear patterns can be caused by
worn suspension parts, misalignment of wheels and
tires, and other suspension related problems.
Spotty wear ± wear localized on shoulder sections, and
in an extreme cases, the tire becomes polygonal in
shape.
480RW002
1. Tire or wheel out of round or distorted.
2. Hub or knuckle out of round or distorted.
3. Play in hub bearings or ball joint.
4. Rotating parts out of balance.Tread wear one-sided.
480RW003
1. Rotating parts out of balance.
2. Tire or wheel out of round.
3. Hub or knuckle out of round or distorted.

INTELLIGENT SUSPENSION3F±1
AXIOM
SUSPENSION
INTELLIGENT SUSPENSION CONTROL
CONTENTS
Service Precaution 3F±2. . . . . . . . . . . . . . . . . . . . . .
General Description 3F±2. . . . . . . . . . . . . . . . . . . . .
PIN ASSIGNMENT TABLE 3F±4. . . . . . . . . . . . .
System Components 3F±4. . . . . . . . . . . . . . . . . . .
Control Unit 3F±4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Actuator 3F±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Damping Force Shock Absorber 3F±4
Warning Lamp 3F±4. . . . . . . . . . . . . . . . . . . . . . . .
Vertical G-Sensor 3F±5. . . . . . . . . . . . . . . . . . . . . .
Lateral G-Sensor 3F±5. . . . . . . . . . . . . . . . . . . . . .
Acronyms and Abbreviations 3F±5. . . . . . . . . . . .
General Diagnosis 3F±5. . . . . . . . . . . . . . . . . . . . . . .
General Information 3F±5. . . . . . . . . . . . . . . . . . . .
Service Precautions 3F±5. . . . . . . . . . . . . . . . . . .
Computer System Service Precautions 3F±5. . .
General Service Precautions 3F±5. . . . . . . . . . . .
Parts Handling 3F±5. . . . . . . . . . . . . . . . . . . . . . . .
FLASHING CODES 3F±6. . . . . . . . . . . . . . . . . . . .
CLEAR DTC 3F±7. . . . . . . . . . . . . . . . . . . . . . . . . .
INTERMITTENT CONDITIONS 3F±8. . . . . . . . .
BULB CHECK 3F±8. . . . . . . . . . . . . . . . . . . . . . . . .
DTC CHECK 3F±8. . . . . . . . . . . . . . . . . . . . . . . . . .
Connector List 3F±14. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Identification 3F±16. . . . . . . . . . . . . . . . . . . . . . . . .
DTC2 Actuator Coil Over Current 3F±17. . . . . . . . . .
Circuit Description 3F±17. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±17. . . . . . . . . . . . . . . . . . . . . . . .
DTC3 Actuator Coil/Position Sensor Open
Circuit or Short 3F±19. . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±19. . . . . . . . . . . . . . . . . . . . . Diagnostic Aids 3F±19. . . . . . . . . . . . . . . . . . . . . . . .
DTC4 G-Sensor Open Circuit or Short 3F±22. . . . .
Circuit Description 3F±22. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±22. . . . . . . . . . . . . . . . . . . . . . . .
DTC5 Vehicle Speed Sensor Open Circuit
or Short 3F±23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±23. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±23. . . . . . . . . . . . . . . . . . . . . . . .
DTC6 Stop Lamp Switch Open Circuit
or Short 3F±25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±25. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±25. . . . . . . . . . . . . . . . . . . . . . . .
DTC7 Engine Speed Signal Open Circuit
or Short 3F±27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±27. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±27. . . . . . . . . . . . . . . . . . . . . . . .
DTC9 Control Unit Abnormality 3F±28. . . . . . . . . . . .
Control Unit 3F±32. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 3F±33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 3F±33. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Actuator 3F±34. . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 3F±35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 3F±35. . . . . . . . . . . . . . . . . . . .
Installation 3F±35. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Shock Absorber 3F±36. . . . . . . . . . . . . . . . . . . .
Removal 3F±37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 3F±37. . . . . . . . . . . . . . . . . . . .
Installation 3F±37. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3F±2INTELLIGENT SUSPENSION
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
General Description
Intellignet suspension control uses a microcomputer as a
control unit to judge running conditions including engine
revolution from Powertrain Control Module, vehicle speed
from vehicle speed sensor, a brake switch signal, and
vertical and lateral G-sensor signal, then sets optimum
damping force so that best running stability can be
achieved.