2002 HONDA PASSPORT torque

188In Case of Emergency
8. Turn the jack handle
clockwise with a slow, smooth
motion to raise the vehicle so
the inflated spare tire will
clear the surface.
9. Remove the wheel nuts and the wheel.
10. Install the wheel and replace the wheel nuts with the
cone-shaped end toward the
wheel, then hand-tighten each
nut. The wheel must be seated
on the hub.
11. Lower the vehicle by turning the jack handle counter-
clockwise, then fully tighten
the wheel nuts in a crisscross
sequence by turning the
wrench clockwise. Have the
wheel nut torque checked at
the nearest automotive service
facility.
87 lb-ft (118 N·m) 12. Stow the jacking tools and flat
tire in their proper locations.
EX model
Use the screwdriver to remove the
center cap from the wheel before
stowing the flat tire.
Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and
tools securely before driving.
The jack is stored in a
compartment on the driver ’s side
rear wheel panel.
To remove the jack from its
compartment, turn the handle
counterclockwise. Disconnect the
hold-down strap.
Tool Locations

•
•Repeated short trips in cold weather
• Driving in dusty areas •
Frequent idling and/or frequent low-speed operation
• Towing a trailer Change engine oil and filter
–Every 3,750 miles (6,000 km)
or 3 months
Change rear axle oil –Every 15,000 miles (24,000 km)
205Care and Maintenance
R – Replace L – Lube I – Inspect After inspection, clean, adjust, repair or replace if necessary.
Service at the interval listed x1 000 il ( k ) ft th tx 1,000 miles7.51522.53037.54552.56067.57582.59097.5105Service at the interval listed x1,000 miles (or km) or after thatnumber of months whicheverx 1,000 km1224364860728496108120132144156168number of months, whichever
comes first.months612182430364248546066727884
Steering and suspension, miscellaneousFront and rear axle oilRRRRPropeller shaft flange torqueIIIIIII
Front and rear propeller shaftsLLLLLLLLLL
Body and chassisLLLLLLLLLLLLLL
Front wheel bearingsRepack bearings when replacing front brake pads.Power steering fluidRRR
Tires (inspect and rotate)IIIIIIIIIIIIII
Suspension and steeringIIIIIIIIIIIIIIBrakes/ClutchBrake discs; calipers and padsIIIIIII
Brake drums, wheel cylinders and liningsIIIIIIIBrake lines and hosesIIIIIIIIIIIIIIParking brakeIIIIIIIBrake pedal playIIIIIIIClutch pedal playIIIIIIIClutch pedal spring, bushing and clevis pinLLLLLLL
Clutch lines and hosesIII
Check oil and coolant level at each fuel stop.
Under severe driving conditions, service these items more often. These c\
onditions are: Service for severe driving conditions

222Care and Maintenance
Front (4WD Only) and Rear
Propeller Shaft
Lubricate the sliding yoke with
EP chassis grease. Lubricate
universal joints with grease
containing MoS
2 (molybdenum
disulfide-type grease) at the
intervals shown in the
Maintenance Schedule. Also
check the propeller shaft
flange-to-pinion bolts for proper
torque of 64 N⋅ m (46.3 lb-ft).
Most lubrication recommendations
and procedures for four-wheel drive-
equipped vehicles are the same
for the corresponding components
in conventional drive vehicles.
Exhaust System
Check the complete exhaust
system and nearby body areas for
damaged, missing, or
mispositioned parts, open seams, holes, loose connections, or other
deterioration that could allow
exhaust fumes to seep into the
passenger compartment or cause
heat build-up in the floor pan. Any
necessary corrections should be
made immediately. For continued
safety, exhaust system pipes and
resonators rearward of the muffler
must be replaced whenever a new
muffler is installed.
Fuel Line and Fuel Tank/Cap
Inspect the fuel tank, cap and lines
for damage that could cause
leakage. Inspect the fuel cap and
gasket for correct sealing ability
and indications of physical
damage. Replace any damaged or
malfunctioning parts.
Drive Belt
Check the belt driving the
alternator, power steering pump,
and air conditioning compressor.
Look for cracks, fraying, and
wear. Replace as necessary.
Timing Belt
The timing belt should normally
be replaced at the intervals shown
in the Maintenance Schedule.
Valve Clearance
Incorrect valve clearance will
result in increased engine noise
and lower engine output, thereby
adversely affecting engine
performance.

Technical Data239
Rear Axle
Models2WD4WDModels2WD4WD
Gear ratio4 3004 300Gear ratio4.3004.300
Lubricant capacity1.87 U.S. quarts(1.77 liters)
Front Axle (4WD Model)
Gear ratio4.300
Lubricant capacity1.6 U.S. quarts (1.5 liters)
Shift-on-the-Fly System
Lubricant capacity0.13 U.S. quarts (0.12 liters)
Wheels and Tires
Tire size225/75R16245/70R16
Wheel size16 x 7 JJ16 x 7 JJ
Tire pressure29 psi (200 kPa)26 psi (180 kPa)
Wheel nut
tightening torque87 lb.ft (118 N.m )