217Care and Maintenance
Recommended Lubricant
Ambient
TemperatureLubricant Viscosity to Be Used
Rear
AxleFront Axle
Below 50F(10 C)
SAE 80
or SAE80W-90
SAE
75W-90
synthetic
0 F to 90hF(–18 C to
32 C)
SAE 90
or SAE
80W-90
SAE
75W-90
synthetic
Above 50 F(10C)
consistentlySAE
140SAE
80W-90
or SAE
80W
-140
The engine cooling system is
designed to maintain the engine at
the proper operating temperatures.
The cooling system was filled at
the factory with a quality engine
coolant. The engine cooling system
is designed to use coolant (a
mixture of water and ethylene
glycol antifreeze) rather than plain
water. The engine coolant solution
should be used year-round. It has
many advantages such as:
•provides freezing protection as
low as –33F (–36C)
• provides boiling protection up
to 262F (128C)
•protects against rust and
corrosion in the cooling system
• maintains the proper engine
temperature for efficient
operation and emission control
•allows proper operation of the
engine coolant temperature gauge See the Maintenance Schedule in
this section to find out when the
engine coolant must be replaced.
Checking the Coolant Level
Check the engine coolant level at
the interval shown in the
Maintenance Schedule unless there
is evidence of leaking or
overheating. The engine coolant
level should be between the
maximum and the minimum level
marks on the radiator reserve tank.
Engine Cooling System
219Care and Maintenance
(–36
C) to ensure protection
against corrosion and loss of
engine coolant from boiling.
This should be done even if
freezing temperatures are not
expected.
•Add ethylene glycol-based
antifreeze when antifreeze has
to be added because of engine
coolant loss or if more
protection against freezing at
temperatures lower than –33F
(–36 C) is needed. Do not use
an alcohol-based or
methanol-based antifreeze, or
plain water. They boil at a
lower point, and do not provide
corrosion protection.
Thermostat
The engine coolant temperature is
controlled by a thermostat, which
stops engine coolant flow through
the radiator until a preset
temperature is reached. This
thermostat is installed in the
engine coolant inlet on the front
of the engine block. The same
thermostat is used in both winter
and summer.Brake Master Cylinder
Check the master cylinder fluid
level in the reservoir every time
you check the engine oil level.
The level should be between the
MAX and ADD level line. If the
level is lower than the
ADD level
line, fill to the
MAX level line
with
DOT-3 or DOT-4 fluid.
Other Required
Maintenance
220 Care and Maintenance
If the diaphragm inside the
reservoir cap is deformed, return
it to the original (collapsed)
condition, then tighten the cap.
It is normal for the brake fluid
level to go down slightly as the
front brake pads wear. So be sure
to keep the reservoir fluid at the
proper level.
If the reservoir needs frequent
refilling, it may indicate a serious
mechanical problem.
Brake fluid absorbs water from
the air. Never use brake fluid that
has been open to the air for an
extended period. Throw it away
and use new brake fluid from a
sealed container.
Brake fluid can damage your
vehicle’s paint. Thoroughly clean
up any brake fluid spills.
Shift-on-the-Fly System
The fluid level in the system should
be checked at the intervals shown
in the Maintenance Schedule.
FILLER
PLUG
Remove the filler plug and make
sure the fluid level is up to the
edge of the hole. If it is not, add
GL-5 gear oil to bring to that
level. Use the same
GL-5 gear oil
specified for the front axle (see
page 216).
Front Wheel Bearings
Clean and repack the front wheel
bearings whenever the front brake
pads are replaced. Due to the
weight of the tire and wheel
assembly it is recommended that
they be removed from the hub
before lubricating the bearings to
prevent damage to the oil seal.
“Long Fiber” grease should not be
used to lubricate the wheel bearings.
It can cause damage. Clean the old
grease out of the bearings and hubs
before repacking.
221Care and Maintenance
Hood Latch and Hinges
Lubricate the hood latch assembly
and hood hinge assembly as
follows:
1. Wipe off any accumulation ofdirt or contamination on the
latch parts.
2. Apply multipurpose-type grease (
NLGI No. 1 or 2) to
the hood latch pin cam.
3. Apply light engine oil to all pivot points in the release
mechanism.
4. Lubricate hood hinges with multipurpose-type grease
(
NLGI No. 1 or 2).
5. Check the hood hinges and latch mechanism to assure
they are working correctly.
Air Conditioning
Periodically have your Honda
dealer check your air conditioning
system to be sure there has been
no loss in cooling output. See
your Honda dealer if you suspect
that the system is not performing
as it should.
Body Lubrication
Normal use of a vehicle causes
metal-to-metal movement at certain
points in the body. Noise, wear and
improper operation at these points
will result when a protective film
of lubricant is not provided.
For exposed surfaces such as door
checks, door lock bolts, lock
striker plates, etc., apply a thin
film of light engine oil.
Any lubricant should be used
sparingly. After application, all excess lubricant should be
carefully wiped off.
The seat adjusters and seat track
should be lubricated with water-
resistant
EP chassis lubricant.
There are other points on the
vehicle body which may
occasionally require lubrication.
Window regulators and controls
are confined in the space between
the upholstery and the outside
door panel. Easy access to the
working parts may be made by
removing the trim. Door
weatherstrips and rubber hood
bumpers should be lightly coated
with a rubber lubricant.
Technical Data235
These specifications are given here for information only. Before using them, see the cautions and other instructions
throughout this manual. For further information, see the Service Manual covering the cha\
ssis or body parts in question.
Your Honda dealer may also be able to help.
Engine
Engine modelV632LItemV6-3.2L
Engine typeWater cooled 4-stroke, 75 V
Piston displacement193.1 cu.in. (3,165 cc)
Number of cylinders6
Compression ratio9.1:1
Spark plugsPK16PR11
Spark plug gap0.04 in. (1.05 mm)
Oil filterFull-flow cartridge type
Oil capacity (Original factory fill or rebuilt engine)6.3 U.S. quarts (6.0 liters)
*Oil capacity (Service change)
with filter change
without filter change
5.0 U.S. quarts (4.7 liters)
4.2 U.S. quarts (4.0 liters)
Idle speed750 rpm
Valve clearance (Cold)Intake
Exhaust0.011 0.002 in. (0.28 0.05 mm)
0.012 0.002 in. (0.30 0.05 mm)
* Oil capacities shown are approximate refill capacities.
* After refill, recheck oil level.
Specifications
256
Break-in158. . . . . . . . . . . . . . .
Fluid
219. . . . . . . . . . . . . . . . . .
Parking
86. . . . . . . . . . . . . . . .
Power
161. . . . . . . . . . . . . . . . .
Wear Indicators
162. . . . . . . . .
Break-in, New Vehicle
158. . . . . .
Brightness Control, Instrument Panel. See Illumination Control
Brights, Headlights
62. . . . . . . .
Bulb Replacement Specifications
243. . . . . . . . . . . .
C
Capacity Charts235. . . . . . . . . . .
Carbon Monoxide Hazard
47. . .
Care and Maintenance
195. . . . . .
Cargo Loading
233. . . . . . . . . . . . . . .
Carrying
17 . . . . . . . . . . . . . . . Cassette Player
Care
141. . . . . . . . . . . . . . . . . .
Operation
128. . . . . . . . . . . . . .
Catalytic Converter, Three-Way
172. . . . . . . . . . . . . .
CAUTION, Explanation ofiv. . .
CD Changer131. . . . . . . . . . . . . .
Certification Label
234. . . . . . . . .
Chains, Tire
168. . . . . . . . . . . . . .
Changing Oil How to
212. . . . . . . . . . . . . . . .
When
204, 205, 211. . . . . . . . .
Changing a Flat Tire
186. . . . . . .
Lifting Points
187. . . . . . . . . . .
Changing Engine Coolant
218. . .
Charging System Indicator
62. .
Check Engine Light
63. . . . . . . .
Checklist, Before Driving
156. . . Children, Protecting
18. . . . . . . .
Child-Safe Door Locks
105. . . . .
Child Seats, General Guidelines
22. . . . . . .
Cigarette Lighter
116. . . . . . . . . .
Circuit Breaker, Checking the
108
Cleaner, Air214. . . . . . . . . . . . . .
Cleaning Exterior
224. . . . . . . . . . . . . . .
Interior
226. . . . . . . . . . . . . . . .
Seat Belts
229. . . . . . . . . . . . . .
Vinyl
229. . . . . . . . . . . . . . . . .
Clock, Setting the
153. . . . . . . . . .
Clutch Fluid
223. . . . . . . . . . . . . .
CO in the Exhaust
47, 249. . . . . .
Consumer Information
246. . . . . .
Control Locations
56. . . . . . . . .
Controls, Instruments and
55. . .
257
Controls Near
the Steering Wheel
Hazard Warning
76. . . . . . . . .
Headlights
72. . . . . . . . . . . . .
Illumination Control
73. . . . .
Rear Window Defogger
74. . .
Steering Wheel Adjustment
115
Turn Signals75. . . . . . . . . . . .
Windshield Wiper/Washer
70.
Rear Window Wiper/ Washer
74. . . . . . . . . . . .
Coolant Adding
218. . . . . . . . . . . . . . . .
Capacity
236. . . . . . . . . . . . . . .
Checking
217. . . . . . . . . . . . . .
Proper Solution
218. . . . . . . . .
Temperature Gauge
60. . . . . .
Corrosion Protection
225. . . . . . .
Courtesy Lights
112. . . . . . . . . . . Crankcase Emissions
Control System
249. . . . . . . . . .
Cruise Control Operation
147. . . .
Customer Relations Information
246. . . . . . . . . . . . .
D
DANGER, Explanation ofiv. . . .
Dashboard
56. . . . . . . . . . . . . . .
Defects, Reporting Safety
248. . .
Defogger, Rear Window
74. . . .
Defrosting the Windows
122. . . .
\b 153
\b\b\b\b\b\b\b\b\b\b\b\b\
\b\b\b
Dimensions243. . . . . . . . . . . . . .
Dimming the Headlights
72. . . .
Dipstick, Engine Oil
200, 213. . .
Directional Signals
75. . . . . . . . . Disc Brake Wear Indicators
162. .
Dome Light
111. . . . . . . . . . . . . .
Door Locks
9. . . . . . . . . . . . . . . .
Power
104. . . . . . . . . . . . . . . . .
Doors, Close and Lock
10. . . . . .
DOT Tire Quality Grading
251. . .
Downshifting, 5-Speed Manual Transmission
84. . . . .
Drive Belts
222. . . . . . . . . . . . . . .
Driving, On-Road Fuel Economy
170. . . . . . . . . .
In Bad Weather
168. . . . . . . . .
In Foreign Countries
173. . . . .
On Slippery Surfaces
162. . . . .
E
Economy, Fuel170. . . . . . . . . . . .
EGR System
250. . . . . . . . . . . . . .
Emergency Brake
86. . . . . . . . . .
258
Emergency Flashers76. . . . . . . .
Emergency, In Case of
183. . . . . .
Charging System Indicator
62
Check Engine Light63. . . . . .
Checking the Fuses
193. . . . . .
Engine Overheating
190. . . . . .
Jump Starting
184. . . . . . . . . . .
Malfunction Indicator Lamp
63
Oil Pressure Indicator65. . . .
Emissions Controls
248. . . . . . . .
Engine Belts
222. . . . . . . . . . . . . . . . . .
Break-in
158. . . . . . . . . . . . . . .
Check Light
63. . . . . . . . . . . .
Coolant Temperature Gauge
60
Identification Number232. . . .
Malfunction Indicator Lamp
63
Oil Capacity
235. . . . . . . . . . . . .
Recommendation
198. . . . . . Oil Pressure Indicator
65. . . .
Specifications
235. . . . . . . . . .
Starting
157. . . . . . . . . . . . . . .
Ethanol in Gasoline
201. . . . . . . .
Evaporative Emissions Controls
249. . . . . . .
Exhaust Fumes
47. . . . . . . . . . . .
Expectant Mothers, Use of Seat Belts by
16. . . . . .
Exterior, Cleaning the
224. . . . . .
F
Fabric, Cleaning. See Interior Cleaning
Fan Control Lever
121. . . . . . . . .
Features, Comfort and Convenience
119. .
Filling the Fuel Tank
197. . . . . . . Filters
Air
214. . . . . . . . . . . . . . . . . . .
Oil
212. . . . . . . . . . . . . . . . . . .
5-Speed Manual Transmission Checking Fluid Level
215. . . .
Shifting
83. . . . . . . . . . . . . . .
Flashers, Hazard Warning
76. . .
Flat Tire, Changing a
186. . . . . . .
Fluids Automatic Transmission
216. .
Capacity
237. . . . . . . . . . . . .
Brake
219. . . . . . . . . . . . . . . . .
Clutch
223. . . . . . . . . . . . . . . .
5-Speed Manual Transmission
215. . . . . . . . . .
Capacity
237. . . . . . . . . . . . .
Power Steering
223. . . . . . . . . .
Windshield Washer
71. . . . . .
FM Stereo Radio Reception
136. . . . . . . . .
Folding the Rear Seat
94. . . . . . .