2002 HONDA ACCORD COUPE drain bolt

Always change the oil and f ilter
accordingtothetimeanddistance
(miles/kilometers) recommenda-
tions in the maintenance schedule.
The oil and f ilter collect contami-
nants that can damage your engine if
they are not removed regularly.Run the engine until it reaches
normal operating temperature,
then shut it off. Open the hood and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
Changing the oil and f ilter requires
special tools and access f rom
underneath the car. The car should
be raised on a service station-type
hydraulic lif t f or this service. Unless
you have the knowledge and proper
equipment, you should have this
maintenance done by a skilled
mechanic.
You may use a synthetic motor oil if
it meets the same requirements
given f or a conventional motor oil: it
displays the API Certif ication Seal,
and it is the proper weight as shown
on the chart. When using synthetic
oil, you must f ollow the oil and f ilter
change intervals given in the
maintenance schedule.
Your Honda does not require any oil
additives. Additives may adversely
af f ect your engine’s or transmission’s
perf ormance and durability.
1.2.
Maint enance
Engine Oil
Synthetic Oil
A dditivesChanging the Oil and Filter
250
4 4-
-c
cy yl liinn d
de
err m
m o
od
de
ellss
W
WA
AS
SHH E
ER
R D
DR
RAA I
INN B
BOOL LTT

Let the engine run f or several
minutes and check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.
Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter): 9. 8. 7.
6. 5.
(Special Edition, EX, and U.S. LX)
(EX-V6 and the U.S. LX-V6) (EX-V6 and the U.S. LX-V6) (Special Edition, EX, and U.S. LX)
Engine Oil
Maint enance252
33 lbf·ft (44 N·m , 4.5 kgf·m)
29 lbf·ft (39 N·m , 4.0 kgf·m)
4.5 US qt (4.3
, 3.8 Imp qt)
4.6 US qt (4.4
, 3.9 Imp qt) Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

4-cylinder models6-cylinder models
Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Remove the drain
bolt and washer f rom the engine
block.Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Loosen the drain
bolt.
3.
Maint enance
Cooling Syst em
256
6 6-
-c
cy yl liinn d
de
err m
m o
od
de
ellss 4
4--c
cy yl liinn d
de
err m
m o
od
de
ellss 6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss D
DR
RAA I
INN B
BOOL LTT
D
D
R
RAA I
INN
P
P L
LUUG G
D
D
R
RAA I
INN
B
BO OL LTT D
D
R
RAA I
INN P
PL
LUUG G

4-cylinder models6-cylinder models 6-cylinder models
With automatic transmission:
With 5-speed manual transmission:
4-cylinder models
4-cylinder models 6-cylinder models
Put a new washer on the drain bolt,
then reinstall the drain bolt in the
engine block. Tighten it securely.
Tightening torque:
Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque: When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Loosen the bleeder bolt on top of
the engine.
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.The cooling system capacity is:
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles.
Pour coolant into the radiator up
to the base of the f iller neck.
7.
6. 5.
Cooling Syst em
Maint enance258
B BL
LEE E
ED
D E
ER
R B
BOOL LTT
61 lbf·ft (83 N·m , 8.5 kgf·m)
7 lbf·ft (10 N·m , 1.0 kgf·m) 1.43 US gal (5.4
, 1.19 Imp gal)
1.45 US gal (5.5
, 1.21 Imp gal)
1.48 US gal (5.6, 1.23 Imp gal)

If Honda MTF is not available, you
may use an API service SG, SH or SJ
grade motor oil with a viscosity of
SAE 10W-30 or 10W-40 as a
temporary replacement. An SG
grade is pref erred, but an SH or SJ
grade may be used if SG is not
available. However, motor oil does
not contain the proper additives and
continued use can cause stif f er
shif ting. Replace as soon as it is
convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
Check the f luid level with the
transmission at normal operating
temperature and the car sitting on
level ground. Remove the
transmission f iller bolt and caref ully
f eel inside the bolt hole with your
f inger. The f luid level should be up
to the edge of the bolt hole. If it is
not, add Honda Manual Transmis-
sion Fluid (MTF) until it starts to
run out of the hole. Reinstall the
f iller bolt and tighten it securely.
T ransmission Fluid
Maint enance
5-speed Manual Transmission
263
F FI
ILLL LEE R
R
B
BO OL LTT C
Co
or
rrreec ctt l
leev veell