2002 HONDA ACCORD COUPE lock

µµBeing able to see
clearly in all directions and being
visible to other drivers are important
in all weather conditions. This is
more dif f icult in bad weather. To be
seen more clearly during daylight
hours, turn on your headlights. Check your tires
f requently f or wear and proper
pressure. Both are important in
preventing ‘‘hydroplaning’’ (loss of
traction on a wet surface). In the
winter, mount snow tires on all f our
wheels f or the best handling.
Watch road conditions caref ully,
they can change f rom moment to
moment. Wet leaves can be as slip-
pery as ice. ‘‘Clear’’ roads can have
patches of ice. Driving conditions
can be very hazardous when the
outside temperature is near f reezing.
The road surf ace can become
covered with areas of water puddles
mixed with areas of ice, so your
traction can change without warning.
Be caref ul when downshif ting. If
traction is low, you can lock up the
drive wheels f or a moment and cause
askid.
Inspect your windshield wipers and
washers f requently. Keep the wind-
shield washer reservoir f ull of the
proper f luid. Have the windshield
wiper blades replaced if they start to
streak the windshield or leave parts
unwiped. Use the def roster and air
conditioning to keep the windows
f rom f ogging up on the inside (see
pages and ).
Be very cautious when passing, or
beingpassedbyothervehicles.The
spray f rom large vehicles reduces
your visibility, and the wind buf f eting
can cause you to lose control.
113 121
Visibility
Traction
Driving in Bad Weather
Driving224

µ
µ
Î
Î
Î Ì
ÌÌ ÌÎÎ
Î
Î
Follow the Severe Conditions
Maintenance Schedule if you
drive your car under
one or more of the f ollowing
conditions: Driving less than 5 miles (8
km) per trip or, in f reezing
temperatures, driving less
than 10 miles (16 km) per trip.
Driving in extremely hot
[over 90°F (32°C)] conditions.
Extensive idling or long
periods of stop-and-go driving.
Trailer towing, driving with a
roof rack, or driving in
mountainous conditions.
Driving on muddy, dusty, or
de-iced roads.
Follow the Maintenance
Schedule f or Severe Conditions.
MAINLY
U.S. Owners
Canadian Owners
Maint enance240
Visually inspect the following items:
Service at the indicated
distance or time whichever
comes first.
miles x 1,000
km x 1,000
months
Replace every 3,750 miles (6,000 km) or 6 monthsCheck oil and coolant at each fuel stop
Every 60,000 miles (96,000 km) or 3 years
Inspect every 7,500 miles (12,000 km) or 6 months
Rotate tires every 7,500 miles (12,000 km)
Every 7,500 miles (12,000 km) or 6 months
Tie rod ends, steering gear box, and boots
Suspension components, Driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and conditions of fluids
Cooling system hoses and connections
Exhaust system, Fuel lines and connections
Lights and controls, Vehicle underbody 15
24
12
30
48
2445
72
3660
96
4875
120 60 90
144 72 105
168
84 120
192
96
120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96,000 km) or 5 years
Balancer belt applies to 4-cylinder models only. See information on maintenance and
emissions warranty, last column, page
.
Every 3 years (independent of mileage)
Replace engine oil and oil filter
Check engine oil and coolant
Clean ( ) or replace ( ) air cleaner element
Use normal schedule except in dusty
conditions
Inspect valve clearance
Replace spark plugs Replace timing belt , balancer belt , and
inspect water pump
Inspect and adjust drive belts
Inspect idle speed
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace dust and pollen filter
Lubricate all hinges, locks, and latches
Rotate tires (Check tire inflation and condition
at least once per month)
See dust and pollen filter on page for replacement information under special driving conditions. See timing belt on page for replacement information under special driving conditions. Adjust only if noisy
MT
AT
1:
2:
3: :
237
281
280
60,000 miles (96,000 km) or 3 years, then every 30,000 miles (48,000 km) or 2 years
11 ,2
3
Maintenance Schedule for Severe Conditions

µµ
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ì
Ì
ÌÎÎ Î
Î
Î
Î
Î
Ì
CONT INUED
Maint enance241
A, B, C, D, E
U.S. Owners
Canadian Owners
A
B
C
D
E
Service at the indicated distance or time, whichever comes first. Do the items in
as required for each distance/time.
Refer to page to determine which schedule to use. Use the Maintenance Schedule for Severe Conditions.
Replace engine oil and filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page267).
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Lubricate all hinges, locks, and latches with
multipurpose grease.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections. Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
3,750 mi/6,000 km
7,500 mi/12,000 km
11,250 mi/18,000 km
15,000 mi/24,000 km/1 yr
18,750 mi/30,000 km
22,500 mi/36,000 km
26,250 mi/42,000 km
30,000 mi/48,000 km/2 yrs
33,750 mi/54,000 km
37,500 mi/60,000 km
41,250 mi/66,000 km
45,000 mi/72,000 km/3 yrs
3 yrs (independent of mileage)
48,750 mi/78,000 km
52,500 mi/84,000 km
56,250 mi/90,000 km
60,000 mi/96,000 km/4 yrs
60,000 mi/96,000 km/3 yrs
60,000 mi/96,000 km/3 yrs
then replace every 30,000 mi/
48,000 km/2 yrs
63,750 mi/102,000 km
67,500 mi/108,000 km
71,250 mi/114,000 km Do items in A.
Do items in A, B.
Do items in A.
Clean air cleaner element.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
Do items in A. Clean air cleaner element.
DoitemsinA,B,C,E.
Do item in E.
Do items in A.
Do items in A, B.
Do items in A. Replace timing belt , balancer belt , and
inspect water pump.
DoitemsinA,B,C,D. Replace MT fluid.
Replace automatic transmission fluid.
Do items in A.
Do items in A, B.
Do items in A. Replace air cleaner element.
Inspect and adjust drive belts.
Replace dust and pollen filter .
Replace brake fluid every 3 years (independent of
mileage).
240
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.
See information on maintenance and emissions warranty, last column, page . See dust and pollen filter on page for replacement information under special driving
conditions. Balancer belt applies to 4-cylinder models only. See timing belt on page for replacement information under special driving conditions. ·
· NOTE:
1:
2:
3: : 237
281
280
11 ,2
3
Maintenance Schedule for Severe Conditions (listed by distance/time)

Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Put the radiator cap back on.
Tighten it f ully.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
3. 2. 4.
5.6.
Cooling Syst em
Maint enance254
4 4-
-c
cy yl liinn d
de
err m
m o
od
de
ellss 6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss
R
RA
A D
DI
IAA T
TO
OR R C
CAA P
P
R
RAA D
DI
IAA T
TO
OR R C
CAA P
P 4
4--c
cy yl liinn d
de
err m
m o
od
de
ellss R
REES
SE ER
RV V E
E T
TA
A N
NK K

4-cylinder models6-cylinder models
Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Remove the drain
bolt and washer f rom the engine
block.Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Loosen the drain
bolt.
3.
Maint enance
Cooling Syst em
256
6 6-
-c
cy yl liinn d
de
err m
m o
od
de
ellss 4
4--c
cy yl liinn d
de
err m
m o
od
de
ellss 6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss D
DR
RAA I
INN B
BOOL LTT
D
D
R
RAA I
INN
P
P L
LUUG G
D
D
R
RAA I
INN
B
BO OL LTT D
D
R
RAA I
INN P
PL
LUUG G

4-cylinder models6-cylinder models 6-cylinder models
With automatic transmission:
With 5-speed manual transmission:
4-cylinder models
4-cylinder models 6-cylinder models
Put a new washer on the drain bolt,
then reinstall the drain bolt in the
engine block. Tighten it securely.
Tightening torque:
Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque: When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Loosen the bleeder bolt on top of
the engine.
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.The cooling system capacity is:
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles.
Pour coolant into the radiator up
to the base of the f iller neck.
7.
6. 5.
Cooling Syst em
Maint enance258
B BL
LEE E
ED
D E
ER
R B
BOOL LTT
61 lbf·ft (83 N·m , 8.5 kgf·m)
7 lbf·ft (10 N·m , 1.0 kgf·m) 1.43 US gal (5.4
, 1.19 Imp gal)
1.45 US gal (5.5
, 1.21 Imp gal)
1.48 US gal (5.6, 1.23 Imp gal)

A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently and have
the system inspected as soon as
possible.
Always use Honda Power Steering
Fluid. If it is not available, you may
use another power steering f luid as
an emergency replacement.
However, continued use can cause
increased wear and poor steering in
cold weather. Have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
Check the level when the engine is
cold. Look at the side of the
reservoir. The f luid should be
between the UPPER LEVEL and
LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
f luid to the UPPER LEVEL.
Power Steering
Maint enance266
6 6-
-c
cy yl liinn d
de
err m
m o
od
de
ellss
4
4- -c
cy yl liinn d
de
err m
m o
od
de
ellss U
UP
PP
PE
ER
R L
LEE V
V E
EL
L
L
LO OW WE ER
R L
LEE V
V E
EL
L
U
UP
PP
PE
ER
R L
LEE V
V E
EL
L
L
LO OW WE ER
R L
LEE V
V E
EL
L
T urning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.

CONT INUED
The spark plugs in your car should
be replaced according to the time
and distance recommendations in
the maintenance schedule.Clean up any dirt and oil that have
collected around the ignition coils.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover on
the f ront cylinder bank by pulling
it straight up.
1.
2.
3.
Maint enance
Spark Plugs (6-cylinder Models)
Replacement
271
H HO
OL LDD I
INNG G C
CLLIIPP