2002 HONDA ACCORD COUPE lights

Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb in the socket.
Turn it clockwise to lock it in place. Remove the burned out bulb f rom
thesocketbypushingitinand
turning the bulb counterclockwise
until it unlocks.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
place by pushing on the center.
1.
3. 2.
4.5.
6.
7.
8.
9.
Replacing Front Turn Signal and
Side Marker L ight Bulbs
Lights
Maint enance292
H H
O
OL LDD I
INNG G C
CLLIIPP

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Open the hood. The f ront parking
light is next to the headlight bulb. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the parking lights to
make sure the new bulb works.
(Passenger’s side)
Reinstall the radiator reserve tank.
(Driver’s side)
If you need to change a bulb on the driver’s side, remove the
radiator reserve tank.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
(Driver’s side)
Reinstall the power steering f luid
tank.
Reinstall the radiator reserve tank.
If you need to change a bulb on
the passenger’s side, remove the
radiator reserve tank. On the
driver’s side, remove the power
steering f luid tank. 2. 3.
1. 4.
5.
6.
4-cylinder models
6-cylinder models
6-cylinder models 4-cylinder models
Replacing a Parking L ight Bulb
Lights
Maint enance293
P P
O
OW WE ER
R S
STTE
EE
ER
RI INNG G F
FLLUUI IDD T
TA
A N
NK K
H
H O
OL LDD E
ER
R

Open the trunk.
Remove the fastener from the side
of the trunk lining by turning it
counterclockwise with a coin. Pull
the lining back.Determine which of the two bulbs
is burned out: stop/taillight or turn
signal/taillight.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
1.
3.
2. 4.
5.
6.
7.
8.
Replacing Rear Bulbs
(in Fenders)
Maint enance
Lights
294
F FA
A S
STTE
EN
NE ER
R

Open the trunk.
Remove the screw securing the
plastic cover. Then remove the
plastic cover.Determine which of the two bulbs
is burned out: stop/taillight or
back-up light.
Put the f astener in the hole on the
side of the trunk lining and push
on the center until it locks (the
center is f lush with the head).
1.
2. 3.
9.
CONT INUED
Replacing Rear Bulbs
(in T runk L id)
Lights
Maint enance295
S SC
CRREEW
W

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly.
Testthelightstomakesurethe
new bulb is working.
Reinstall the plastic cover and
secure it with the screw.Use a Phillips-head screwdriver to
loosen the side marker assembly
mounting screw.
Remove the assembly f rom the
f ender by pulling out the back
edge and sliding the assembly
backwards. Remove the socket f rom the light
assembly by turning it counter-
clockwise.
Remove the bulb f rom the socket
by pulling it straight out.
Install the new bulb. Turn on the
headlights to test the bulb.
1.
2.
4.
5.
6.
7.
8.
4. 3.
Replacing a Rear Side Marker
Light Bulb
Lights
Maint enance296
S SC
CRREEW
W

Insert the socket in the assembly.
Turn it clockwise to lock it in place.
Reinstall the side marker assem-
bly in the bumper. Tighten the
mounting screw securely.Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb in the socket.Reinstall the socket. Turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
1.
2. 3.
5.
6. 4.
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance297

Turn on the parking lights and
check that the new bulb is
working.
Put the lens back into the light
assembly, right side f irst. Push on
the lef t edge until it snaps into
place.
Insert a flat-tipped screwdriver
between the lef t edge of the lens
and the housing. The lens will
come down. Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.
1.
2. 3.
4.
Replacing a Rear License Plate
Bulb
Lights
Maint enance298

The ceiling light, door light and
vanity mirror light come apart the
same way, but they do not use the
same type of bulb.Door light:Pryonthetopmiddleof thelens.
Removethelensbycarefully
prying on the edge of the lens with
a f ingernail f ile or a small f lat-tip
screwdriver. Do not pry on the
edge of the housing around the
lens.
Ceiling light:Pry on the f ront edge of the lens
near both sides.
1.
CONT INUED
Replacing Bulbs in the Interior
Courtesy Lights
Lights
Maint enance299
C CE
EI
ILLI INNG G L
LIIGGH HT
T D
DO
OO ORR L
LIIGGH HT
T