2002 HONDA ACCORD COUPE ECU

Check the f luid level with the engine
at normal operating temperature.Insert the dipstick all the way into
the transmission securely as
shown in the illustration.
Remove the dipstick (yellow loop)
f rom the transmission and wipe it
with a clean cloth. Park the car on level ground. Shut
of f the engine.
1.
2. 3.
CONT INUED
Automatic Transmission
T ransmission Fluid
Maint enance261
U UP
PP
PE
ER
R M
M A
AR
RKK
L
LO OW WE ER
R M
M A
AR
RKK
D
D I
IPP S
ST TI
ICCK K
4
4- -c
cy yl liinn d
de
err m
m o
od
de
ellss D
D
I
IPP S
ST TI
ICCK K
6
6- -c
cy yl liinn d
de
err m
m o
od
de
ellss D
DI
IPP S
ST TI
ICCK K 4
4--c
cy yl liinn d
de
err m
m o
od
de
ellss

µ
µ
Remove the dipstick and check
the f luid level. It should be
between the upper and lower
marks. If the level is below the lower
mark, add f luid to bring it to the
upper mark.
Add f luid in the
dipstick tube.
Remove the f ill
plug to add f luid.
Always use Honda ATF-Z1
(Automatic Transmission Fluid). If
it is not available, you may use a
DEXRON
III automatic
transmission f luid as a temporary
replacement. However, continued
use can affect shift quality. Have
the transmission f lushed and
ref illed with Honda ATF-Z1 as
soon as it is convenient.
To thoroughly f lush the
transmission, the technician
should drain and ref ill it with
Honda ATF-Z1, then drive the
vehicle a short distance. Do this three times. Then drain and ref ill
the transmission a final time.
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If you are not sure how to add f luid,
contact your Honda dealer.
5.
6.
4.
4-cylinder cars 6-cylinder cars
Maint enance
T ransmission Fluid
262
D DI
IPP S
ST TI
ICCK K
6
6- -c
cy yl liinn d
de
err m
m o
od
de
ellss U
UP
PP
PE
ER
R M
M A
AR
RKK
L
LO OW WE ER
R M
M A
AR
RKK

If Honda MTF is not available, you
may use an API service SG, SH or SJ
grade motor oil with a viscosity of
SAE 10W-30 or 10W-40 as a
temporary replacement. An SG
grade is pref erred, but an SH or SJ
grade may be used if SG is not
available. However, motor oil does
not contain the proper additives and
continued use can cause stif f er
shif ting. Replace as soon as it is
convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
Check the f luid level with the
transmission at normal operating
temperature and the car sitting on
level ground. Remove the
transmission f iller bolt and caref ully
f eel inside the bolt hole with your
f inger. The f luid level should be up
to the edge of the bolt hole. If it is
not, add Honda Manual Transmis-
sion Fluid (MTF) until it starts to
run out of the hole. Reinstall the
f iller bolt and tighten it securely.
T ransmission Fluid
Maint enance
5-speed Manual Transmission
263
F FI
ILLL LEE R
R
B
BO OL LTT C
Co
or
rrreec ctt l
leev veell

´
µ
Install the ignition coil. Reinstall
the hexagon socket head cap bolt.Push the wire connector onto the
ignition coil. Make sure it locks in
place.
Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.Spark Plug Gap:
NGK:
DENSO:
8. 9.
10.
11.
Spark Plugs (6-cylinder Models)
Maint enance
Specif ications:
273
0.04 in (1.1 mm) PKJ16CR-L11 PZFR5F-110
0.1 mm
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

Open the trunk.
Remove the screw securing the
plastic cover. Then remove the
plastic cover.Determine which of the two bulbs
is burned out: stop/taillight or
back-up light.
Put the f astener in the hole on the
side of the trunk lining and push
on the center until it locks (the
center is f lush with the head).
1.
2. 3.
9.
CONT INUED
Replacing Rear Bulbs
(in T runk L id)
Lights
Maint enance295
S SC
CRREEW
W

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly.
Testthelightstomakesurethe
new bulb is working.
Reinstall the plastic cover and
secure it with the screw.Use a Phillips-head screwdriver to
loosen the side marker assembly
mounting screw.
Remove the assembly f rom the
f ender by pulling out the back
edge and sliding the assembly
backwards. Remove the socket f rom the light
assembly by turning it counter-
clockwise.
Remove the bulb f rom the socket
by pulling it straight out.
Install the new bulb. Turn on the
headlights to test the bulb.
1.
2.
4.
5.
6.
7.
8.
4. 3.
Replacing a Rear Side Marker
Light Bulb
Lights
Maint enance296
S SC
CRREEW
W

Insert the socket in the assembly.
Turn it clockwise to lock it in place.
Reinstall the side marker assem-
bly in the bumper. Tighten the
mounting screw securely.Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb in the socket.Reinstall the socket. Turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
1.
2. 3.
5.
6. 4.
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance297

Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.Clean the windows, inside and out,
with a commercially-available glass
cleaner. You can also use a mixture
of one part white vinegar to ten parts
water. This will remove the haze that
builds up on the inside of the
windows. Use a sof t cloth or paper
towels to clean all glass and clear
plastic surf aces.If you want to use an air f reshener/
deodorizer in the interior of your car,
it is best to use a solid type. Some
liquid air f resheners contain chemi-
cals that may cause parts of the
interior trim and f abric to crack or
discolor.
If youusealiquidairfreshener,
make sure you f asten it securely so it
does not spill as you drive.
Interior Care
Appearance Care
Windows
A ir Fresheners
308
The rear window def ogger and
antenna wires are bonded to the inside
of the glass. Wiping vigorously up-and-
down can dislodge and break these
wires. When cleaning the rear window,
use gentle pressure and wipe side-to-
side.