2002 GMC ENVOY ignition

3-31
(CLEAN): If this message appears on the display, the
cassette tape player needs to be cleaned. It will still play
tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index. After you clean
the player, press and hold the cassette eject button for
five seconds to reset the CLEAN indicator. The radio
display will display CLEANED to show the indicator
was reset.
If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer.
Tight/Loose Tape Sensor Defeat
With the radio off and the ignition on, press and hold the
TAPE CD button to disable the tight/loose tape sensing
feature to enable play of some tape head cleaners and
portable CD adapters. The radio will display READY
and flash the cassette icon. The tight/loose tape sensing
feature will then be disabled until the next time a
cassette is ejected.Playing a Compact Disc
Insert a disc partway into the slot, label side up. The
player will pull it in and the disc should begin playing.
The display will show the CD symbol. If you want to
insert a compact disc with the ignition off, first press
TUNE DISP or EJT.
If an error appears on the display, see ªRadio/Compact
Disc Messagesº later in this section.
1 PREV: Press this button or the left SEEK PSCAN
arrow to go to the previous track if the current selection
has been playing for less than eight seconds. If the
1 PREV button or the left SEEK PSCAN arrow is
pressed and the current selection has been playing for
more than eight seconds, it will go to the beginning of
the current selection. TRACK and the track number will
appear on the display. If you hold the 1 PREV button or
left SEEK PSCAN arrow or press it more than once, the
player will continue moving back through the disc. The
sound will mute while seeking.
2 NEXT: Press this button or the right SEEK PSCAN
arrow to go to the next track. TRACK and the track
number will appear on the display. If you hold the
2 NEXT button or the right SEEK PSCAN arrow
or press it more than once, the player will continue
moving forward through the disc. The sound will mute
while seeking.

3-32
3 REV: Press and hold this button to reverse quickly
within a track. Press and hold this button for less than
two seconds to reverse at six times the normal playing
speed. Press and hold it for more than two seconds to
reverse at 17 times the normal playing speed. Release it
to play the passage. The display will show ET and the
elapsed time.
4 FWD: Press and hold this button to advance quickly
within a track. Press and hold this button for less than
two seconds to advance at six times the normal playing
speed. Press and hold it for more than two seconds to
advance at 17 times the normal playing speed. Release it
to play the passage. The display will show ET and the
elapsed time.
6
RDM: Press this button to hear the tracks in
random, rather than sequential, order. RDM ON will
appear on the display. RDM T and the track number
will appear on the display when each track starts to play.
Press 6 RDM again to turn off random play. RDM OFF
will appear on the display.
SEEK PSCAN
: Press the left SEEK PSCAN
arrow to go to the start of the current or previous track.
Press the right SEEK PSCAN button to go to the start of
the next track. If either of the SEEK PSCAN arrows is
held or pressed more then once, the player will continue
moving backward or forward through the CD.TUNE DISP: Press this control to see how long the
current track has been playing. ET and the elapsed time
will appear on the display. To change what is normally
shown on the display (track or elapsed time), press the
control until you see the display you want, then hold
the control for two seconds. The radio will produce
one beep.
AM FM: Press this button to play the radio when
a disc is in the player. The disc will stop but remain in
the player.
CD AUX: With a CD in the player and the radio
playing, press this button to play a CD. Press AM FM
to return to the radio when a CD is playing. The inactive
CD will remain safely inside the radio for
future listening.
EJT: Press this button to remove the disc.
The radio will play. Eject may be activated with either
the ignition or radio off. CDs may be loaded with the
radio and ignition off if this button is pressed first.

3-40
Playing a Compact Disc
LOAD CD
: Press this button to load CDs into the
compact disc player. This compact disc player will
accommodate up to six discs.
To insert one disc do the following:
1. Turn the ignition on.
2. Press and release the LOAD CD button.
3. Wait for the light, located to the right of the slot, to
turn green.
4. Load a disc. Insert a disc partway into the slot, label
side up. The player will pull the disc in.
When the disc is inserted, the CD symbol will be
displayed. If you select an EQ setting for your disc,
it will be activated each time you play a disc.
If the radio is on or off, the disc will begin to
play automatically.
To insert multiple discs do the following:
1. Turn the ignition on.
2. Press and hold the LOAD CD button for
two seconds.
You will then hear a beep and the light, located to the
right of the slot, will begin to flash.3. Once the light stops flashing and turns green, load a
disc. Insert a disc partway into the slot, label side up.
The player will pull the disc in.
Once the disc is loaded, the light will begin flashing
again. Once the light stops flashing and turns green
you can then load another disc. The disc player takes
up to six discs. Do not try to load more than six.
When a disc is inserted, the CD symbol will be
displayed. If more than one disc has been loaded, a
number for each disc will be displayed. If you select
an EQ setting for your disc, it will be activated each
time you play a disc.
If the radio is on or off, the last disc loaded will
begin to play automatically.
4. To load more than one disc but less than six,
complete Steps 1, 2 and 3. When you have finished
loading discs, with the radio on or off, press the
LOAD CD button to cancel the loading function.
The radio will begin to play the last CD loaded.
As each new track starts to play, the track number will
appear on the display.

3-48
To use the video screen, do the following:
1. Push forward on the release button and the screen
will fold down.
2. Push the screen away from you and adjust its
position as desired.
When the video screen is not in use, push it up into
its locked position.
The DVD player and display will continue to operate
when the display is in either the up or down position.
NOTICE:
Avoid directly touching the video screen,
as damage may occur. See ªCleaning the Video
Screenº in the Index for more information.
DVD Player
The DVD player is located in the overhead console.
The DVD player can be controlled by the buttons
on the DVD player and by the buttons on the remote
control. See ªRemote Controlº later in this section
for more information.
The DVD player works while the ignition is in
RUN or ACCESSORY and while RAP is active.
See ªRetained Accessory Power (RAP)º in the Index
for more information.

3-54 Tips and Troubleshooting Chart
ProblemRecommended Action
No power.The ignition might be on.
The parental control button
might have been pressed.
(The power LED will flash.)
Disc will
not play.The Input/Title on the remote
might be set for auxiliary.
The disc is upside down or
is not compatible.
No sound.The volume on the headphones
could be too low. Adjust it on
the front panel or the remote.
The picture is
distorted during
fast forward or
fast reverse.This is normal for this operation.
ProblemRecommended Action
The picture
does not fill
the screen.
There are black
borders on the
top and bottom
or on both sides
or it looks
stretched out.Quickly press and release the
SIZE/ANGLE button on the
remote. This will fill the screen.
If the screen looks stretched
out, press and release the
SIZE/ANGLE button again.
If there are borders on the top
and bottom, the movie may have
been made that way for a standard
screen. Pressing the SIZE/ANGLE
button should fill the sides.
I ejected the disc
and tried to take
it out, but it was
pulled back into
the slot.Eject the disc again.

3-63 Diversity Antenna System
Your AM FM antennas are located in the rear side
windows. Be sure that the inside surfaces of the rear side
windows are not scratched and that the lines on the glass
are not damaged. If the inside surfaces are damaged,
they could interfere with radio reception.
NOTICE:
Do not try to clear frost or other material from
the inside of the rear side windows with a razor
blade or anything else that is sharp. This may
affect your radio's ability to pick up stations
clearly. The repairs wouldn't be covered by
your warranty.
If you choose to add an aftermarket cellular telephone
to your vehicle, and the antenna needs to be attached to
the glass, be sure that you do not damage the grid lines
for the AM FM antennas or place the cellular telephone
antenna over the grid lines.
Chime Level Adjustment
The volume level of the vehicle's chimes can be
controlled by the radio. To change the volume level,
press and hold pushbutton 6 with the ignition on
and the radio power off. The chime volume level will
change from the normal level to loud, and LOUD will
be displayed on the radio. To change back to the default
or normal setting, press and hold pushbutton 6 again.
The chime level will change from the loud level to
normal, and NORMAL will be displayed.

4-10
The TRAC OFF light on the button will come on under
the following conditions:

The Traction Assist System is turned off, either by
pressing the TAS on/off button or turning off the
automatic engagement feature of the TAS.

The transmission is in FIRST (1); TAS will not
operate in this gear. This is normal.

The vehicle is driven on an extremely rough road.
When the vehicle leaves the rough surface, slows
down or stops, the light will go off and TAS will be
on again. This is normal.

A Traction Assist System, Anti
-Lock Brake System
or engine
-related problem has been detected and the
vehicle needs service.
The Traction Assist System, as delivered from the
factory, will automatically come on whenever you start
your vehicle. To limit wheel spin, especially in slippery
road conditions, you should always leave the system on.
But you can turn the TAS off if you ever need to. You
should turn the TAS off if your vehicle ever gets stuck in
sand, mud or snow and rocking the vehicle is required.
See ªRocking Your Vehicleº in the Index.
To turn the system on
or off press the TAS
on/off button located
near the shift lever.
If you used the button
to turn the system off,
the TRAC OFF light
on the button will
come on and stay on.
You can turn the system back on at any time by pressing
the button again. The TRAC OFF light on the button
should go off.
If desired, you can change the TAS automatic
engagement feature so that the system will not come on
automatically when the engine is started. To do so:
1. Park the vehicle with the ignition off and the
transmission in PARK (P).
2. Turn the ignition to RUN; do not start the engine.

4-11
3. Apply the brake pedal, press the accelerator pedal to
the floor and then press the TAS on/off button and
hold it down for at least six seconds.
4. Release the TAS button and both pedals.
5. Turn off the ignition and wait a few seconds.
The next time you start your vehicle, the TAS will not
automatically come on. You can restore the automatic
feature by using the same procedure. Whether the
TAS is set to come on automatically or not, you can
always turn the system on or off by pressing the TAS
on/off button.
Steering
Power Steering
If you lose power steering assist because the engine
stops or the system is not functioning, you can steer
but it will take much more effort.
Steering Tips
Driving on Curves
It's important to take curves at a reasonable speed.
A lot of the ªdriver lost controlº accidents mentioned
on the news happen on curves. Here's why:Experienced driver or beginner, each of us is subject to
the same laws of physics when driving on curves. The
traction of the tires against the road surface makes it
possible for the vehicle to change its path when you turn
the front wheels. If there's no traction, inertia will keep
the vehicle going in the same direction. If you've ever
tried to steer a vehicle on wet ice, you'll understand this.
The traction you can get in a curve depends on the
condition of your tires and the road surface, the angle
at which the curve is banked, and your speed.
While you're in a curve, speed is the one factor you
can control.
Suppose you're steering through a sharp curve.
Then you suddenly accelerate. Both control
systems
-- steering and acceleration -- have to do
their work where the tires meet the road. Adding the
sudden acceleration can demand too much of those
places. You can lose control. Refer to ªTraction Assist
Systemº in the Index.
What should you do if this ever happens? Ease up on the
accelerator pedal, steer the vehicle the way you want it
to go, and slow down.
Speed limit signs near curves warn that you should
adjust your speed. Of course, the posted speeds are
based on good weather and road conditions. Under less
favorable conditions you'll want to go slower.