2002 DODGE RAM turn signal

OVERDRIVE SWITCH
DESCRIPTION
The overdrive OFF (control) switch is located in
the shift lever arm (Fig. 113). The switch is a
momentary contact device that signals the PCM to
toggle current status of the overdrive function.
OPERATION
At key-on, overdrive operation is allowed. Pressing
the switch once causes the overdrive OFF mode to be
entered and the overdrive OFF switch lamp to be
illuminated. Pressing the switch a second timecauses normal overdrive operation to be restored and
the overdrive lamp to be turned off. The overdrive
OFF mode defaults to ON after the ignition switch is
cycled OFF and ON. The normal position for the con-
trol switch is the ON position. The switch must be in
this position to energize the solenoid and allow a 3-4
upshift. The control switch indicator light illuminates
only when the overdrive switch is turned to the OFF
position, or when illuminated by the transmission
control module.
DIAGNOSIS AND TESTING - OVERDRIVE
ELECTRICAL CONTROLS
The overdrive off switch, valve body solenoid, case
connectors and related wiring can all be tested with
a 12 volt test lamp or a volt/ohmmeter. Check conti-
nuity of each component when diagnosis indicates
this is necessary.
Switch and solenoid continuity should be checked
whenever the transmission fails to shift into fourth
gear range.
REMOVAL
(1) Using a plastic trim tool, remove the overdrive
off switch retainer from the shift lever (Fig. 114).
(2) Pull the switch outwards to release it from the
connector in the lever (Fig. 115)
Fig. 112 Overdrive Clutch
1 - REACTION PLATE 2 - PRESSURE PLATE
Fig. 113 Overdrive Off Switch
21 - 344 AUTOMATIC TRANSMISSION - 47REBR/BE
OVERDRIVE CLUTCH (Continued)

control the current flow through the solenoid to posi-
tion the solenoid plunger at a desired position some-
where between full ON and full OFF. The constant
ON and duty cycled versions control the voltage
across the solenoid to allow either full flow or no flow
through the solenoid's valve.
OPERATION
When an electrical current is applied to the sole-
noid coil, a magnetic field is created which produces
an attraction to the plunger, causing the plunger to
move and work against the spring pressure and the
load applied by the fluid the valve is controlling. The
plunger is normally directly attached to the valve
which it is to operate. When the current is removed
from the coil, the attraction is removed and the
plunger will return to its original position due to
spring pressure.
The plunger is made of a conductive material and
accomplishes this movement by providing a path for
the magnetic field to flow. By keeping the air gap
between the plunger and the coil to the minimum
necessary to allow free movement of the plunger, the
magnetic field is maximized.
SPEED SENSOR
DESCRIPTION
The speed sensor (Fig. 223) is located in the over-
drive gear case. The sensor is positioned over the
park gear and monitors transmission output shaft
rotating speed.
OPERATION
Speed sensor signals are triggered by the park
gear lugs as they rotate past the sensor pickup face.
Input signals from the sensor are sent to the trans-
mission control module for processing. Signals from
this sensor are shared with the powertrain control
module.
THROTTLE VALVE CABLE
DESCRIPTION
Transmission throttle valve cable (Fig. 224) adjust-
ment is extremely important to proper operation.
This adjustment positions the throttle valve, which
controls shift speed, quality, and part-throttle down-
shift sensitivity.
If cable setting is too loose, early shifts and slip-
page between shifts may occur. If the setting is too
tight, shifts may be delayed and part throttle down-
shifts may be very sensitive.
The transmission throttle valve is operated by a
cam on the throttle lever. The throttle lever is oper-
ated by an adjustable cable (Fig. 225). The cable is
attached to an arm mounted on the throttle lever
shaft. A retaining clip at the engine-end of the cable
is removed to provide for cable adjustment. The
retaining clip is then installed back onto the throttle
valve cable to lock in the adjustment.
Fig. 223 Transmission Output Speed Sensor
1 - TRANSMISSION OUTPUT SHAFT SPEED SENSOR
2 - SEAL
Fig. 224 Throttle Valve Cable Attachment - At
Engine
1 - THROTTLE VALVE CABLE
2 - CABLE BRACKET
3 - THROTTLE BODY LEVER
4 - ACCELERATOR CABLE
5 - SPEED CONTROL CABLE
BR/BEAUTOMATIC TRANSMISSION - 47RE 21 - 381
SOLENOID (Continued)

TIRES
DESCRIPTION
DESCRIPTION - SPARE TIRE - TEMPORARY
The temporary spare tire is designed for emer-
gency use only. The original tire should be repaired
or replaced at the first opportunity, then reinstalled.
Do not exceed speeds of 50 M.P.H. when using the
temporary spare tire. Refer to Owner's Manual for
complete details.
DESCRIPTION - TIRES
Tires are designed and engineered for each specific
vehicle. They provide the best overall performance
for normal operation. The ride and handling charac-
teristics match the vehicle's requirements. With
proper care they will give excellent reliability, trac-
tion, skid resistance, and tread life.
Driving habits have more effect on tire life than
any other factor. Careful drivers will obtain in most
cases, much greater mileage than severe use or care-
less drivers. A few of the driving habits which will
shorten the life of any tire are:
²Rapid acceleration
²Severe brake applications
²High speed driving
²Excessive speeds on turns
²Striking curbs and other obstacles
Radial-ply tires are more prone to irregular tread
wear. It is important to follow the tire rotation inter-
val shown in the section on Tire Rotation, (Refer to
22 - TIRES/WHEELS - STANDARD PROCEDURE).
This will help to achieve a greater tread life.
TIRE IDENTIFICATION
Tire type, size, aspect ratio and speed rating are
encoded in the letters and numbers imprinted on the
side wall of the tire. Refer to the chart to decipher
the tire identification code (Fig. 11).
Performance tires have a speed rating letter after
the aspect ratio number. The speed rating is not
always printed on the tire sidewall. These ratings
are:
²Qup to 100 mph
²Rup to 106 mph
²Sup to 112 mph
²Tup to 118 mph
²Uup to 124 mph
²Hup to 130 mph
²Vup to 149 mph
²Zmore than 149 mph (consult the tire manu-
facturer for the specific speed rating)An All Season type tire will have eitherM+S,M
&SorM±S(indicating mud and snow traction)
imprinted on the side wall.
TIRE CHAINS
Tire snow chains may be used oncertainmodels.
Refer to the Owner's Manual for more information.
DESCRIPTION - RADIAL-PLY TIRES
Radial-ply tires improve handling, tread life and
ride quality, and decrease rolling resistance.
Radial-ply tires must always be used in sets of
four. Under no circumstances should they be used on
the front only. They may be mixed with temporary
spare tires when necessary. A maximum speed of 50
MPH is recommended while a temporary spare is in
use.
Radial-ply tires have the same load-carrying capac-
ity as other types of tires of the same size. They also
use the same recommended inflation pressures.
The use of oversized tires, either in the front or
rear of the vehicle, can cause vehicle drive train fail-
ure. This could also cause inaccurate wheel speed
signals when the vehicle is equipped with Anti-Lock
Brakes.
The use of tires from different manufactures on the
same vehicle is NOT recommended. The proper tire
pressure should be maintained on all four tires.
Fig. 11 Tire Identification
22 - 6 TIRES/WHEELSBR/BE

CAB SIDE PANEL SPEAKER - REMOVAL,
REAR..............................8A-20
CABLE - ADJUSTMENTS,
TRANSMISSION THROTTLE
VALVE ......................21-210,21-382
CABLE - DESCRIPTION.................8P-4
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DESCRIPTION, BATTERY........8F-18
CABLE - DESCRIPTION, SPARK PLUG.....8I-20
CABLE - DESCRIPTION, THROTTLE
VALVE ......................21-209,21-381
CABLE - INSTALLATION, ANTENNA BODY . . 8A-6
CABLE - INSTALLATION, CHECK.........23-67
CABLE - INSTALLATION, FRONT
PARKING BRAKE......................5-30
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-9
CABLE - INSTALLATION, LATCH RELEASE . 23-103
CABLE - INSTALLATION, REAR PARK
BRAKE..............................5-30
CABLE - INSTALLATION, RELEASE.......23-82
CABLE - INSTALLATION, SPARK PLUG....8I-21
CABLE - INSTALLATION, THROTTLE
CONTROL....................14-110,14-50
CABLE - OPERATION...................8P-4
CABLE - OPERATION, ANTENNA BODY.....8A-4
CABLE - OPERATION, BATTERY..........8F-18
CABLE - OPERATION, SPARK PLUG.......8I-20
CABLE - REMOVAL, ANTENNA BODY......8A-6
CABLE - REMOVAL, CHECK.............23-67
CABLE - REMOVAL, FRONT PARKING
BRAKE..............................5-29
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-9
CABLE - REMOVAL, LATCH RELEASE....23-103
CABLE - REMOVAL, REAR PARK BRAKE . . . 5-29
CABLE - REMOVAL, RELEASE...........23-82
CABLE - REMOVAL, SPARK PLUG........8I-21
CABLE - REMOVAL, THROTTLE
CONTROL....................14-109,14-49
CABLE INSTALLATION, GASOLINE
ENGINE - NEGATIVE..................8F-22
CABLE INSTALLATION, GASOLINE
ENGINE - POSITIVE...................8F-22
CABLE ORDER, 8.0L V-10 ENGINE -
SPARK PLUG.........................8I-3
CABLE REMOVAL, GASOLINE ENGINE -
NEGATIVE..........................8F-22
CABLE REMOVAL, GASOLINE ENGINE -
POSITIVE...........................8F-21
CABLE RESISTANCE, SPECIFICATIONS -
SPARK PLUG.........................8I-3
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-19
CABLES - DIAGNOSIS AND TESTING,
SPARK PLUG........................8I-20
CAB-TO-BED GROUND STRAP -
INSTALLATION.......................8A-14
CAB-TO-BED GROUND STRAP -
REMOVAL..........................8A-13
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-4
CALIPERS - DESCRIPTION, DISC BRAKE . . . 5-10
CALIPERS - OPERATION, DISC BRAKE.....5-10
CAM - DESCRIPTION, TURN SIGNAL
CANCEL............................8L-31
CAM - OPERATION, TURN SIGNAL
CANCEL............................8L-31
CAM BORE REPAIR - STANDARD
PROCEDURE........................9-151
CAM/OVERDRIVE PISTON RETAINER -
ASSEMBLY, OVERRUNNING
CLUTCH.....................21-193,21-364
CAM/OVERDRIVE PISTON RETAINER -
CLEANING, OVERRUNNING
CLUTCH
.....................21-192,21-364
CAM/OVERDRIVE PISTON RETAINER -
DESCRIPTION, OVERRUNNING
CLUTCH
.....................21-192,21-363
CAM/OVERDRIVE PISTON RETAINER -
DISASSEMBLY, OVERRUNNING
CLUTCH
.....................21-192,21-364
CAM/OVERDRIVE PISTON RETAINER -
INSPECTION, OVERRUNNING
CLUTCH
.....................21-193,21-364
CAM/OVERDRIVE PISTON RETAINER -
OPERATION, OVERRUNNING
CLUTCH
.....................21-192,21-363CAMSHAFT - INSTALLATION....9-157,9-29,9-86
CAMSHAFT - REMOVAL.......9-152,9-28,9-85
CAMSHAFT BEARINGS - I
NSTALLATION...............9-157,9-28,9-86
CAMSHAFT BEARINGS -
REMOVAL..................9-152,9-27,9-85
CANCEL CAM - DESCRIPTION, TURN
SIGNAL............................8L-31
CANCEL CAM - OPERATION, TURN
SIGNAL............................8L-31
CANISTER - DESCRIPTION, VAPOR......25-37
CANISTER - INSTALLATION, CRANKCASE
BREATHER VAPOR...................9-126
CANISTER - INSTALLATION, VAPOR......25-38
CANISTER - OPERATION, VAPOR........25-37
CANISTER - REMOVAL, CRANKCASE
BREATHER VAPOR...................9-125
CANISTER - REMOVAL, VAPOR..........25-38
CAP - DESCRIPTION, FUEL FILLER.......25-34
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-64
CAP - DIAGNOSIS AND TESTING,
DISTRIBUTOR.......................8I-14
CAP - DIAGNOSIS AND TESTING,
RADIATOR...........................7-65
CAP - OPERATION, FUEL FILLER........25-34
CAP - OPERATION, RADIATOR
PRESSURE..........................7-64
CAP - REMOVAL/INSTALLATION, FUEL
FILLER.............................25-34
CAPACITIES, SPECIFICATIONS - FLUID.......0-6
CAPACITY TEST - DIAGNOSIS AND
TESTING, FUEL PUMP..................14-9
CARDAN UNIVERSAL JOINTS -
ASSEMBLY, DOUBLE...................3-11
CARDAN UNIVERSAL JOINTS -
ASSEMBLY, SINGLE.....................3-9
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, DOUBLE................3-10
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, SINGLE..................3-8
CARDAN UNIVERSAL JOINTS -
INSTALLATION, SINGLE.................3-35
CARDAN UNIVERSAL JOINTS -
REMOVAL, SINGLE....................3-34
CARGO BOX - INSTALLATION...........23-97
CARGO BOX - REMOVAL...............23-97
CARGO DOOR - ADJUSTMENT..........23-78
CARPETS AND FLOOR MATS -
INSTALLATION......................23-123
CARPETS AND FLOOR MATS - REMOVAL . 23-123
CARTRIDGE FUSE - DESCRIPTION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - INSTALLATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - OPERATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - REMOVAL,
GENERATOR......................8W-97-4
CASE - DIAGNOSIS AND TESTING,
TRANSFER...................21-431,21-467
CASE - NV241 - DESCRIPTION,
TRANSFER
............................0-5
CASE - NV241HD - ASSEMBLY,
TRANSFER
.........................21-480
CASE - NV241HD - CLEANING,
TRANSFER
.........................21-476
CASE - NV241HD - DESCRIPTION,
TRANSFER
.........................21-465
CASE - NV241HD - DISASSEMBLY,
TRANSFER
.........................21-469
CASE - NV241HD - INSPECTION,
TRANSFER
.........................21-476
CASE - NV241HD - INSTALLATION,
TRANSFER
.........................21-494
CASE - NV241HD - OPERATION,
TRANSFER
.........................21-467
CASE - NV241HD - REMOVAL,
TRANSFER
.........................21-469
CASE - NV241LD - ASSEMBLY,
TRANSFER
.........................21-445
CASE - NV241LD - CLEANING,
TRANSFER
.........................21-441
CASE - NV241LD - DESCRIPTION,
TRANSFER
.........................21-430
CASE - NV241LD - DISASSEMBLY,
TRANSFER
.........................21-432CASE - NV241LD - INSPECTION,
TRANSFER.........................21-442
CASE - NV241LD - INSTALLATION,
TRANSFER.........................21-458
CASE - NV241LD - OPERATION,
TRANSFER.........................21-430
CASE - NV241LD - REMOVAL,
TRANSFER.........................21-432
CASE BEARINGS - INSTALLATION,
DIFFERENTIAL..........3-102,3-129,3-41,3-72
CASE BEARINGS - REMOVAL,
DIFFERENTIAL..........3-102,3-129,3-40,3-72
CASE, NV241HD - TRANSFER..........21-495
CASE, NV241LD - TRANSFER..........21-459
CASE SKID PLATE - INSTALLATION,
TRANSFER..........................13-11
CASE SKID PLATE - REMOVAL,
TRANSFER..........................13-11
CASE, SPECIFICATIONS -
TRANSFER...................21-458,21-495
CASTER CORRECTION MEASUREMENT -
STANDARD PROCEDURE.................2-3
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- DESCRIPTION.......................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSPECTION........................11-6
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSTALLATION......................11-6
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- OPERATION.........................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- REMOVAL..........................11-5
CATALYTIC CONVERTER - 5.9L HD/8.0L -
DESCRIPTION........................11-6
CATALYTIC CONVERTER - 5.9L HD/8.0L -
INSPECTION.........................11-6
CATALYTIC CONVERTER - 5.9L HD/8.0L -
INSTALLATION........................11-7
CATALYTIC CONVERTER - 5.9L HD/8.0L -
OPERATION..........................11-6
CATALYTIC CONVERTER - 5.9L HD/8.0L -
REMOVAL...........................11-6
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING................21-157,21-327
CCD DATA BUS - DESCRIPTION..........8E-6
CCD DATA BUS - DIAGNOSIS AND
TESTING...........................8E-11
CCD DATA BUS - OPERATION............8E-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-8
CENTER - INSTALLATION, POWER
DISTRIBUTION...................8W-97-10
CENTER - OPERATION, POWER
DISTRIBUTION....................8W-97-8
CENTER - REMOVAL, POWER
DISTRIBUTION....................8W-97-8
CENTER BEARING - ADJUSTMENT.........3-8
CENTER BEARING - INSTALLATION........3-8
CENTER BEARING - REMOVAL............3-8
CENTER CONSOLE - INSTALLATION.....23-122
CENTER CONSOLE - REMOVAL.........23-122
CENTER CONSOLE LID - INSTALLATION . . 23-132
CENTER CONSOLE LID - REMOVAL.....23-131
CENTER HIGH MOUNTED STOP LAMP -
INSTALLATION........................8L-6
CENTER HIGH MOUNTED STOP LAMP -
REMOVAL...........................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION..................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL.....................8L-6
CENTER SEAT ARMREST/CONSOLE -
INSTALLATION......................23-132
CENTER SEAT ARMREST/CONSOLE -
REMOVAL.........................23-132
CENTER SEAT ARMREST/LATCH COVER -
INSTALLATION......................23-132
CENTER SEAT ARMREST/LATCH COVER -
REMOVAL.........................23-132
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING
......................8O-11
CENTRAL TIMER MODULE -
DESCRIPTION
........................8E-1
CENTRAL TIMER MODULE - DIAGNOSIS
AND TESTING
........................8E-4
CENTRAL TIMER MODULE -
INSTALLATION
........................8E-6
CENTRAL TIMER MODULE - OPERATION
. . . 8E-3
BR/BEINDEX 5
Description Group-Page Description Group-Page Description Group-Page

GRID - DIAGNOSIS AND TESTING,
HEATED MIRROR.....................8G-4
GRID - OPERATION, HEATED MIRROR.....8G-4
GRILLE - INSTALLATION...............23-91
GRILLE - INSTALLATION, COWL.........23-90
GRILLE - REMOVAL..................23-91
GRILLE - REMOVAL, COWL............23-90
GRILLE FRAME - INSTALLATION.........23-92
GRILLE FRAME - REMOVAL............23-91
GRILLES - INSTALLATION, DEMISTER....24-31
GRILLES - REMOVAL, DEMISTER........24-31
GROUND STRAP - INSTALLATION,
CAB-TO-BED........................8A-14
GROUND STRAP - INSTALLATION,
ENGINE-TO-BODY....................8A-13
GROUND STRAP - INSTALLATION,
HEATER CORE.......................8A-14
GROUND STRAP - REMOVAL,
CAB-TO-BED........................8A-13
GROUND STRAP - REMOVAL,
ENGINE-TO-BODY....................8A-12
GROUND STRAP - REMOVAL, HEATER
CORE..............................8A-14
GUIDES AND SPRINGS - STANDARD
PROCEDURE, VALVES..................9-23
HANDLE - INSTALLATION, A-PILLAR
GRAB.............................23-119
HANDLE - INSTALLATION, ASSIST......23-124
HANDLE - INSTALLATION, EXTERIOR.....23-71
HANDLE - INSTALLATION, LATCH.........23-66
HANDLE - INSTALLATION, RELEASE.......5-32
HANDLE - INSTALLATION, SHUTFACE.....23-83
HANDLE - REMOVAL, A-PILLAR GRAB . . . 23-119
HANDLE - REMOVAL, ASSIST..........23-124
HANDLE - REMOVAL, EXTERIOR........23-71
HANDLE - REMOVAL, LATCH...........23-66
HANDLE - REMOVAL, RELEASE..........5-31
HANDLE - REMOVAL, SHUTFACE........23-83
HANDLE ACTUATOR - INSTALLATION,
INSIDE........................23-72,23-80
HANDLE ACTUATOR - REMOVAL, INSIDE . 23-72,
23-80
HANDLE ESCUTCHEON - INSTALLATION . . 23-64
HANDLE ESCUTCHEON - REMOVAL......23-64
HANDLING NON-DEPLOYED AIRBAGS -
STANDARD PROCEDURE...............8O-4
HARNESS - DIAGNOSIS AND TESTING,
WIRING..........................8W-01-7
HAZARD WARNING SYSTEM -
DESCRIPTION, TURN SIGNAL............8L-2
HAZARD WARNING SYSTEM -
DIAGNOSIS AND TESTING, TURN
SIGNAL.............................8L-3
HAZARD WARNING SYSTEM -
OPERATION, TURN SIGNAL.............8L-2
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION........................5-40
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION........................5-41
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION..........................5-40
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL...........................5-41
HD/8.0L - DESCRIPTION, CATALYTIC
CONVERTER - 5.9L....................11-6
HD/8.0L - INSPECTION, CATALYTIC
CONVERTER - 5.9L....................11-6
HD/8.0L - INSPECTION, EXHAUST PIPE -
5.9L................................11-8
HD/8.0L - INSPECTION, TAILPIPE - 5.9L . . 11-12
HD/8.0L - INSTALLATION, CATALYTIC
CONVERTER - 5.9L....................11-7
HD/8.0L - INSTALLATION, EXHAUST PIPE
- 5.9L..............................11-8
HD/8.0L - INSTALLATION, TAILPIPE -
5.9L...............................11-12
HD/8.0L - OPERATION, CATALYTIC
CONVERTER - 5.9L....................11-6
HD/8.0L - REMOVAL, CATALYTIC
CONVERTER - 5.9L....................11-6
HD/8.0L - REMOVAL, EXHAUST PIPE -
5.9L................................11-7
HD/8.0L - REMOVAL, TAILPIPE - 5.9L
....11-12
HEAD - CLEANING, CYLINDER
......9-134,9-77
HEAD - DESCRIPTION, CYLINDER
. . . 9-130,9-20,
9-76
HEAD - INSPECTION, CYLINDER
.....9-134,9-77
HEAD - INSTALLATION, CYLINDER
........9-77HEAD - OPERATION, CYLINDER..........9-21
HEAD - REMOVAL, CYLINDER......9-130,9-76
HEAD COVER GASKET - DESCRIPTION,
CYLINDER...........................9-20
HEAD COVER GASKET - OPERATION,
CYLINDER...........................9-21
HEAD COVER(S) - CLEANING, CYLINDER . 9-137,
9-23,9-79
HEAD COVER(S) - DESCRIPTION,
CYLINDER...........................9-78
HEAD COVER(S) - INSPECTION,
CYLINDER..................9-138,9-23,9-79
HEAD COVER(S) - INSTALLATION,
CYLINDER..................9-138,9-23,9-79
HEAD COVER(S) - REMOVAL, CYLINDER . 9-137,
9-23,9-78
HEAD GASKET FAILURE - DIAGNOSIS
AND TESTING, CYLINDER...........9-21,9-76
HEADLAMP - DESCRIPTION............8L-13
HEADLAMP - DIAGNOSIS AND TESTING . . 8L-14
HEADLAMP - INSTALLATION............8L-16
HEADLAMP - OPERATION..............8L-13
HEADLAMP - REMOVAL...............8L-16
HEADLAMP ALIGNMENT, SPECIAL
TOOLS..............................8L-4
HEADLAMP RELAY - DESCRIPTION . . . 8W-97-13
HEADLAMP RELAY - DESCRIPTION......8L-17
HEADLAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-17
HEADLAMP RELAY - INSTALLATION . . . 8W-97-13
HEADLAMP RELAY - INSTALLATION......8L-18
HEADLAMP RELAY - OPERATION........8L-17
HEADLAMP RELAY - REMOVAL......8W-97-13
HEADLAMP RELAY - REMOVAL.........8L-18
HEADLAMP SWITCH - DESCRIPTION.....8L-18
HEADLAMP SWITCH - DIAGNOSIS AND
TESTING...........................8L-19
HEADLAMP SWITCH - INSTALLATION....8L-20
HEADLAMP SWITCH - OPERATION.......8L-18
HEADLAMP SWITCH - REMOVAL........8L-19
HEADLAMP UNIT - ADJUSTMENTS......8L-21
HEADLAMP UNIT - INSTALLATION.......8L-21
HEADLAMP UNIT - REMOVAL...........8L-20
HEADLINER - INSTALLATION..........23-125
HEADLINER - REMOVAL..............23-125
HEAT SHIELDS - DESCRIPTION.........11-10
HEAT SHIELDS - INSTALLATION.........11-10
HEAT SHIELDS - REMOVAL.............11-10
HEAT/DEFROST DOOR - INSTALLATION . . . 24-38
HEAT/DEFROST DOOR - REMOVAL.......24-37
HEAT/DEFROST DOOR ACTUATOR -
INSTALLATION.......................24-27
HEAT/DEFROST DOOR ACTUATOR -
REMOVAL..........................24-26
HEATED MIRROR GRID - DESCRIPTION . . . 8G-4
HEATED MIRROR GRID - DIAGNOSIS
AND TESTING........................8G-4
HEATED MIRROR GRID - OPERATION.....8G-4
HEATED MIRROR SWITCH - DIAGNOSIS
AND TESTING........................8G-3
HEATED MIRROR SYSTEM -
DESCRIPTION........................8G-1
HEATED MIRROR SYSTEM - DIAGNOSIS
AND TESTING........................8G-2
HEATED MIRROR SYSTEM - OPERATION . . . 8G-2
HEATED SEAT ELEMENT - DESCRIPTION . . 8G-10
HEATED SEAT ELEMENT - INSTALLATION . 8G-13
HEATED SEAT ELEMENT - OPERATION....8G-11
HEATED SEAT ELEMENT - REMOVAL.....8G-13
HEATED SEAT ELEMENT AND SENSOR -
DIAGNOSIS AND TESTING.............8G-11
HEATED SEAT MODULE - DESCRIPTION . . . 8E-20
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING.......................8E-21
HEATED SEAT MODULE - INSTALLATION . . 8E-23
HEATED SEAT MODULE - OPERATION....8E-20
HEATED SEAT MODULE - REMOVAL......8E-23
HEATED SEAT RELAY - DESCRIPTION....8G-14
HEATED SEAT RELAY - DIAGNOSIS AND
TESTING...........................8G-15
HEATED SEAT RELAY - INSTALLATION....8G-16
HEATED SEAT RELAY - OPERATION
......8G-15
HEATED SEAT RELAY - REMOVAL
.......8G-16
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING
...................8G-17,8G-8
HEATED SEAT SYSTEM - DESCRIPTION
....8G-5
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING
........................8G-6HEATED SEAT SYSTEM - OPERATION.....8G-6
HEATER - 5.9L - DESCRIPTION, ENGINE
BLOCK..............................7-44
HEATER - 5.9L - INSTALLATION, ENGINE
BLOCK..............................7-44
HEATER - 5.9L - OPERATION, ENGINE
BLOCK..............................7-44
HEATER - 5.9L - REMOVAL, ENGINE
BLOCK..............................7-44
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-46
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-46
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-46
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.......................7-46
HEATER - 8.0L - DESCRIPTION, ENGINE
BLOCK..............................7-45
HEATER - 8.0L - INSTALLATION, ENGINE
BLOCK..............................7-45
HEATER - 8.0L - OPERATION, ENGINE
BLOCK..............................7-45
HEATER - 8.0L - REMOVAL, ENGINE
BLOCK..............................7-45
HEATER - DESCRIPTION, FUEL..........14-66
HEATER - DESCRIPTION, INTAKE AIR....14-104
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-66
HEATER - INSTALLATION, INTAKE AIR . . . 14-105
HEATER - OPERATION, FUEL............14-66
HEATER - OPERATION, INTAKE AIR.......14-104
HEATER - REMOVAL, INTAKE AIR.......14-104
HEATER - REMOVAL/INSTALLATION,
FUEL..............................14-67
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DIAGNOSIS AND
TESTING, A/C.......................24-18
HEATER CORE - DESCRIPTION..........24-56
HEATER CORE - INSTALLATION.........24-56
HEATER CORE - OPERATION............24-56
HEATER CORE - REMOVAL.............24-56
HEATER CORE GROUND STRAP -
INSTALLATION.......................8A-14
HEATER CORE GROUND STRAP -
REMOVAL..........................8A-14
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-6
HEATER RELAY - DESCRIPTION, FUEL....14-67
HEATER RELAY - DESCRIPTION, INTAKE
AIR ..............................14-105
HEATER RELAY - DIAGNOSIS AND
TESTING, FUEL......................14-68
HEATER RELAY - INSTALLATION, FUEL . . . 14-69
HEATER RELAY - INSTALLATION, INTAKE
AIR ..............................14-106
HEATER RELAY - OPERATION, FUEL......14-67
HEATER RELAY - OPERATION, INTAKE
AIR ..............................14-105
HEATER RELAY - REMOVAL, FUEL.......14-69
HEATER RELAY - REMOVAL, INTAKE AIR . 14-106
HEATER SWITCH - DESCRIPTION,
DRIVER SEAT........................8G-7
HEATER SWITCH - DESCRIPTION,
PASSENGER SEAT....................8G-16
HEATER SWITCH - INSTALLATION,
DRIVER SEAT.......................8G-10
HEATER SWITCH - INSTALLATION,
PASSENGER SEAT....................8G-19
HEATER SWITCH - OPERATION, DRIVER
SEAT ...............................8G-8
HEATER SWITCH - OPERATION,
PASSENGER SEAT....................8G-17
HEATER SWITCH - REMOVAL, DRIVER
SEAT ...............................8G-9
HEATER SWITCH - REMOVAL,
PASSENGER SEAT....................8G-18
HGT ADJUSTER KNOB - INSTALLATION,
TURNING LOOP
.....................8O-30
HGT ADJUSTER KNOB - REMOVAL,
TURNING LOOP
.....................8O-30
HIGH BEAM INDICATOR - DESCRIPTION
. . 8J-21
HIGH BEAM INDICATOR - DIAGNOSIS
AND TESTING
.......................8J-21
HIGH BEAM INDICATOR - OPERATION
....8J-21
BR/BEINDEX 15
Description Group-Page Description Group-Page Description Group-Page

HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE FUEL LINES -
DESCRIPTION.......................14-78
HIGH PRESSURE FUEL LINES -
OPERATION.........................14-78
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-46
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-47
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-20
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-20
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-20
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-20
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-20
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-78
HINGE - INSTALLATION.....23-100,23-72,23-80
HINGE - REMOVAL........23-100,23-72,23-79
HITCH - INSTALLATION, TRAILER.........13-11
HITCH - REMOVAL, TRAILER...........13-11
HOISTING - STANDARD PROCEDURE.......0-9
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-17
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-18
HOLDDOWN - OPERATION, BATTERY.....8F-17
HOLDDOWN - REMOVAL, BATTERY......8F-17
HOLDER - INSTALLATION, CUP........23-110
HOLDER - REMOVAL, CUP............23-109
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE..................9-11,9-65
HOOD - INSTALLATION...............23-101
HOOD - REMOVAL...................23-101
HOOK - INSTALLATION, COAT..........23-125
HOOK - INSTALLATION, FRONT TOW.....13-10
HOOK - REMOVAL, COAT.............23-124
HOOK - REMOVAL, FRONT TOW.........13-10
HORN - DESCRIPTION.............8H-1,8H-2
HORN - DIAGNOSIS AND TESTING.......8H-2
HORN - INSTALLATION.................8H-3
HORN - OPERATION...............8H-1,8H-2
HORN - REMOVAL....................8H-2
HORN RELAY - DESCRIPTION.......8W-97-12
HORN RELAY - DESCRIPTION...........8H-3
HORN RELAY - DIAGNOSIS AND
TESTING........................8W-97-12
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - INSTALLATION.......8W-97-12
HORN RELAY - INSTALLATION...........8H-4
HORN RELAY - OPERATION.............8H-3
HORN RELAY - REMOVAL..........8W-97-12
HORN RELAY - REMOVAL..............8H-4
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-5
HORN SWITCH - OPERATION............8H-5
HORN SWITCH - REMOVAL.............8H-5
HOSE CLAMPS - DESCRIPTION...........7-4
HOSE CLAMPS - OPERATION.............7-4
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-76
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-73
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-77
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-76
HOSES - PRESSURE - DESCRIPTION
.....19-39
HOSES - PRESSURE - OPERATION
.......19-39
HOSES - RETURN - DESCRIPTION
.......19-39
HOSES - RETURN - OPERATION
.........19-39
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT
..............24-43HOSES/TUBES - DESCRIPTION, WASHER . . 8R-8
HOSES/TUBES - OPERATION, WASHER....8R-8
HOUSING - ASSEMBLY, HVAC...........24-36
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-9
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH......6-11
HOUSING - INSTALLATION, GEAR........9-188
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - REMOVAL, CLUTCH..........6-11
HOUSING - REMOVAL, GEAR...........9-187
HOUSING - REMOVAL, HVAC...........24-34
HOUSING BUSHING - INSTALLATION,
EXTENSION..................21-156,21-326
HOUSING BUSHING - REMOVAL,
EXTENSION..................21-156,21-326
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-460,21-497
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-460,21-497
HOUSING COVER - INSTALLATION, GEAR . 9-190
HOUSING COVER - REMOVAL, GEAR.....9-189
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-101,21-273
HOUSING INLET BAFFLE -
INSTALLATION, HVAC.................24-36
HOUSING INLET BAFFLE - REMOVAL,
HVAC..............................24-35
HOUSING PLUG - INSTALLATION,
STEERING GEAR.......................19-30
HOUSING PLUG - REMOVAL, STEERING
GEAR..............................19-29
HOUSING SEAL - INSTALLATION,
EXTENSION..................21-156,21-327
HOUSING SEAL - NV4500 -
INSTALLATION, ADAPTER..............21-42
HOUSING SEAL - NV4500 -
INSTALLATION, EXTENSION............21-42
HOUSING SEAL - NV4500 - REMOVAL,
ADAPTER...........................21-42
HOUSING SEAL - NV4500 - REMOVAL,
EXTENSION.........................21-42
HOUSING SEAL - NV5600 -
INSTALLATION, ADAPTER..............21-85
HOUSING SEAL - NV5600 -
INSTALLATION, EXTENSION............21-85
HOUSING SEAL - NV5600 - REMOVAL,
ADAPTER...........................21-85
HOUSING SEAL - NV5600 - REMOVAL,
EXTENSION.........................21-85
HOUSING SEAL - REMOVAL,
EXTENSION..................21-156,21-326
HUB / BEARING - INSTALLATION......2-17,2-9
HUB / BEARING - REMOVAL..........2-16,2-9
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HVAC HOUSING INLET BAFFLE -
INSTALLATION.......................24-36
HVAC HOUSING INLET BAFFLE -
REMOVAL..........................24-35
HVAC SYSTEM AIRFLOW - DESCRIPTION . 24-30
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-18
HYDRAULIC LIFTERS - CLEANING
....9-37,9-92
HYDRAULIC LIFTERS - INSTALLATION
. 9-37,9-92
HYDRAULIC LIFTERS - REMOVAL
....9-37,9-92
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING
.......21-270,21-98
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS
..............21-132,21-302
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING
........................9-36,9-91
HYDRAULIC/MECHANICAL -
DESCRIPTION
.........................5-4
HYDRAULIC/MECHANICAL - WARNING
.....5-4
HYDROMETER TEST - STANDARD
PROCEDURE
........................8F-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
................9-11,9-122,9-66
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION LAMP - INSTALLATION,
OUTBOARD
.........................8L-29IDENTIFICATION LAMP - REMOVAL,
OUTBOARD.........................8L-28
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-1
IDENTIFICATION PLATE - DESCRIPTION,
EQUIPMENT.......................Intro.-3
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-40
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-40
IGNITION - SPECIFICATIONS, TORQUE.....8I-2
IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-17
IGNITION CIRCUIT SENSE - OPERATION . . 8E-19
IGNITION COIL RESISTANCE, 5.9L
ENGINES............................8I-3
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-4
IGNITION SWITCH - DESCRIPTION.......19-11
IGNITION SWITCH - DESCRIPTION,
KEY-IN..............................19-9
IGNITION SWITCH - DIAGNOSIS AND
TESTING...........................19-11
IGNITION SWITCH - INSTALLATION......19-12
IGNITION SWITCH - OPERATION........19-11
IGNITION SWITCH - REMOVAL..........19-12
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING....19-9
IGNITION TIMING, SPECIFICATIONS.......8I-4
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-13
INDEPENDENT FRONT SUSPENSION,
SPECIAL TOOLS.......................2-9
INDICATOR - DESCRIPTION, ABS........8J-14
INDICATOR - DESCRIPTION, AIRBAG.....8J-15
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-15
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-17
INDICATOR - DESCRIPTION, CRUISE.....8J-18
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-20
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-21
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SERVICE
REMINDER..........................8J-27
INDICATOR - DESCRIPTION, TRANS
OVERTEMP.........................8J-31
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-32
INDICATOR - DESCRIPTION, UPSHIFT....8J-32
INDICATOR - DESCRIPTION, VTSS........8Q-3
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-34
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-36
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-16
INDICATOR - DIAGNOSIS AND TESTING,
FOUR-WHEEL DRIVE..................8J-29
INDICATOR - DIAGNOSIS AND TESTING,
HIGH BEAM.........................8J-21
INDICATOR - DIAGNOSIS AND TESTING,
TURN SIGNAL
.......................8J-32
INDICATOR - DIAGNOSIS AND TESTING,
VTSS
...............................8Q-4
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID
......................8J-35
INDICATOR - OPERATION, ABS
..........8J-14
INDICATOR - OPERATION, AIRBAG
.......8J-15
INDICATOR - OPERATION, BRAKE/PARK
BRAKE
.............................8J-15
INDICATOR - OPERATION, CHECK
GAUGES
............................8J-17
INDICATOR - OPERATION, CRUISE
.......8J-18
INDICATOR - OPERATION, GEAR
SELECTOR
..........................8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-21
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, SEATBELT
.....8J-27
16 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

INDICATOR - OPERATION, SERVICE
REMINDER..........................8J-28
INDICATOR - OPERATION, TRANS
OVERTEMP.........................8J-31
INDICATOR - OPERATION, TURN SIGNAL . . 8J-32
INDICATOR - OPERATION, UPSHIFT......8J-33
INDICATOR - OPERATION, VTSS.........8Q-3
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-34
INDICATOR - OPERATION, WASHER
FLUID..............................8J-35
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-36
INDICATOR LAMP MIL - DESCRIPTION,
MALFUNCTION.......................8J-23
INDICATOR LAMP MIL - OPERATION,
MALFUNCTION.......................8J-23
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATOR (TRANSFER CASE) -
DESCRIPTION, SHIFT.................8J-28
INDICATOR (TRANSFER CASE) -
OPERATION, SHIFT...................8J-28
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-33
INJECTION - SPECIFICATIONS, TORQUE -
GAS FUEL..........................14-35
INJECTION PUMP - DESCRIPTION, AIR.....25-29
INJECTION PUMP - DIAGNOSIS AND
TESTING, AIR.......................25-29
INJECTION PUMP - INSTALLATION, AIR . . . 25-30
INJECTION PUMP - OPERATION, AIR.....25-29
INJECTION PUMP - REMOVAL, AIR......25-30
INJECTION PUMP DATA PLATE,
SPECIFICATIONS - FUEL...............14-77
INJECTION PUMP RELAY -
DESCRIPTION, FUEL.................14-103
INJECTION PUMP RELAY - OPERATION,
FUEL.............................14-103
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-70
INJECTION SYSTEM - DESCRIPTION, AIR . 25-26
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-91
INJECTION SYSTEM - OPERATION, AIR . . . 25-28
INJECTION SYSTEM - TORQUE, AIR......25-29
INJECTOR - DESCRIPTION, FUEL . . . 14-52,14-97
INJECTOR - DIAGNOSIS AND TESTING,
FUEL..............................14-53
INJECTOR - INSTALLATION, FUEL.......14-102
INJECTOR - OPERATION, FUEL..........14-98
INJECTOR - REMOVAL, FUEL..........14-101
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-62
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL......................14-99
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-36
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-35
INLET FILTER - INSTALLATION..........14-23
INLET FILTER - REMOVAL..............14-23
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-153
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-153
IN/OUT - ADJUSTMENT, FRONT DOOR
....23-70
INPUT - DESCRIPTION, VEHICLE SPEED
. . . 8P-2
INPUT - OPERATION, ASD SENSE - PCM
. . . 8I-4
INSIDE HANDLE ACTUATOR -
INSTALLATION
..................23-72,23-80
INSIDE HANDLE ACTUATOR - REMOVAL
. . 23-72,
23-80
INSPECTION - CONNECTING RODS
......9-169
INSPECTION - INSPECTION
.............9-169
INSPECTION - INSTALLATION
......9-136,9-170
INSPECTION, 5.9L ENGINES - VISUAL
....14-29
INSPECTION, 8.0L ENGINE - VISUAL
.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH
............................24-15
INSPECTION, ACCUMULATOR
....21-150,21-320
INSPECTION, BATTERY SYSTEM
..........8F-6INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-6
INSPECTION, CATALYTIC CONVERTER -
5.9L HD/8.0L.........................11-6
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-19
INSPECTION, CROSSHEADS............9-135
INSPECTION, CYLINDER HEAD......9-134,9-77
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-23,9-79
INSPECTION, DIAGNOSIS AND TESTING . . . 7-66
INSPECTION, DIAGNOSIS AND TESTING . 21-122,
21-293
INSPECTION, DIAGNOSIS AND TESTING
- WHEEL...........................22-11
INSPECTION, ENGINE BLOCK........9-27,9-85
INSPECTION, EXHAUST MANIFOLD . 9-109,9-186,
9-53
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HD/8.0L.............................11-8
INSPECTION, FRONT CLUTCH....21-162,21-332
INSPECTION, FRONT SERVO.....21-164,21-335
INSPECTION, INSPECTION.............9-169
INSPECTION, INTAKE MANIFOLD . . . 9-108,9-184,
9-51
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ............................9-26
INSPECTION, MANUAL - NV4500........21-20
INSPECTION, MANUAL - NV5600........21-63
INSPECTION, MEASURING TIMING
CHAIN STRETCH.................9-111,9-54
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-179
INSPECTION, OIL PAN.......9-103,9-179,9-46
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-180
INSPECTION, OIL PUMP......9-104,9-181,9-47
INSPECTION, OIL PUMP........21-168,21-339
INSPECTION, OPERATION...............9-22
INSPECTION, OVERDRIVE UNIT . . 21-180,21-353
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-193,
21-364
INSPECTION, PISTON & CONNECTING
ROD............................9-39,9-94
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT...............21-199,21-371
INSPECTION, PUSHRODS..............9-135
INSPECTION, RADIATOR - 5.9L..........7-60
INSPECTION, RADIATOR - 5.9L DIESEL....7-64
INSPECTION, RADIATOR - 8.0L..........7-61
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-43
INSPECTION, RADIATOR FAN - 5.9L/8.0L . . . 7-42
INSPECTION, REAR CLUTCH.....21-204,21-377
INSPECTION, REMOVAL................5-12
INSPECTION, REMOVAL...........9-155,9-83
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-146
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-165
INSPECTION, STANDARD PROCEDURE....9-151
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L . . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL....11-12
INSPECTION, TAILPIPE - 5.9L HD/8.0L....11-12
INSPECTION, TRANSFER CASE -
NV241HD..........................21-476
INSPECTION, TRANSFER CASE -
NV241LD..........................21-442
INSPECTION, TURBOCHARGER..........11-16
INSPECTION, VALVE BODY......21-244,21-419
INSPECTION, VIBRATION DAMPER.......9-172
INSPECTION, WATER PUMP - 5.9L........7-68
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-72
INSPECTION, WATER PUMP - 8.0L........7-71
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSTRUMENT CLUSTER - ASSEMBLY.....8J-12
INSTRUMENT CLUSTER - DESCRIPTION
. . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING
........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY
. . 8J-10
INSTRUMENT CLUSTER - INSTALLATION
. . 8J-13
INSTRUMENT CLUSTER - OPERATION
.....8J-3INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-9
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION......................23-117
INSTRUMENT PANEL ASSEMBLY -
REMOVAL.........................23-115
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-36
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-36
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-105
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-113
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-113
INTAKE AIR HEATER - DESCRIPTION....14-104
INTAKE AIR HEATER - INSTALLATION....14-105
INTAKE AIR HEATER - OPERATION......14-104
INTAKE AIR HEATER - REMOVAL.......14-104
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-105
INTAKE AIR HEATER RELAY -
INSTALLATION.......................14-106
INTAKE AIR HEATER RELAY -
OPERATION........................14-105
INTAKE AIR HEATER RELAY - REMOVAL . 14-106
INTAKE MANIFOLD - CLEANING....9-107,9-184,
9-51
INTAKE MANIFOLD - DESCRIPTION . . 9-106,9-50
INTAKE MANIFOLD - INSPECTION . . 9-108,9-184,
9-51
INTAKE MANIFOLD - INSTALLATION.....9-108,
9-184,9-51
INTAKE MANIFOLD - OPERATION.........9-50
INTAKE MANIFOLD - REMOVAL....9-107,9-184,
9-50
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING.........9-106,9-50
INTAKE/EXHAUST VALVES & SEATS -
CLEANING...........................9-26
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION...............9-138,9-23,9-80
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION.........................9-26
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION........................9-26
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL...........................9-25
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR...................7-78,7-82,7-84
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITHOUT
RADIATOR...................7-79,7-82,7-85
INTERIOR - CAUTION................23-118
INTERIOR LAMPS, SPECIFICATIONS......8L-33
INTERMEDIATE - REMOVAL, AXLE
SHAFTS.............................3-30
INTERMEDIATE AXLE - INSTALLATION.....3-30
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-5
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-3,9-58
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
IOD FUSE - DESCRIPTION...........8W-97-5
IOD FUSE - INSTALLATION...........8W-97-6
IOD FUSE - OPERATION.............8W-97-5
IOD FUSE - REMOVAL
..............8W-97-6
ISO FLARING - STANDARD PROCEDURE
....5-8
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL
........................2-10
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL
.........................2-12
JOINT MOLDING - INSTALLATION, ROOF
. . 23-91
BR/BEINDEX 17
Description Group-Page Description Group-Page Description Group-Page

JOINT MOLDING - REMOVAL, ROOF......23-91
JOINTS - ASSEMBLY, DOUBLE CARDAN
UNIVERSAL..........................3-11
JOINTS - ASSEMBLY, SINGLE CARDAN
UNIVERSAL...........................3-9
JOINTS - DISASSEMBLY, DOUBLE
CARDAN UNIVERSAL..................3-10
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL...................3-8
JOINTS - INSTALLATION, SINGLE
CARDAN UNIVERSAL..................3-35
JOINTS - REMOVAL, SINGLE CARDAN
UNIVERSAL..........................3-34
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD
BEARING AND CRANKSHAFT...........9-158
JUMP STARTING - STANDARD
PROCEDURE..........................0-7
JUNCTION BLOCK - DESCRIPTION.....8W-97-6
JUNCTION BLOCK - DIAGNOSIS AND
TESTING.........................8W-97-7
JUNCTION BLOCK - INSTALLATION....8W-97-8
JUNCTION BLOCK - OPERATION......8W-97-7
JUNCTION BLOCK - REMOVAL........8W-97-7
KEEPER - INSTALLATION, BACKLITE
LATCH ............................23-146
KEEPER - REMOVAL, BACKLITE LATCH . . 23-146
KEY LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH.............19-9
KEY-IN IGNITION SWITCH -
DESCRIPTION........................19-9
KEYLESS ENTRY SYSTEM -
DESCRIPTION, REMOTE................8N-2
KEYLESS ENTRY SYSTEM - DIAGNOSIS
AND TESTING, POWER LOCK &
REMOTE............................8N-5
KEYLESS ENTRY SYSTEM - OPERATION,
REMOTE............................8N-4
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-8
KEYLESS ENTRY TRANSMITTER -
OPERATION, REMOTE..................8N-8
KEYLESS ENTRY TRANSMITTER
BATTERIES - STANDARD PROCEDURE,
REMOTE............................8N-8
KNOB - INSTALLATION, TURNING LOOP
HGT ADJUSTER.....................8O-30
KNOB - REMOVAL, TURNING LOOP HGT
ADJUSTER.........................8O-30
KNUCKLE - INSTALLATION..........2-10,2-19
KNUCKLE - REMOVAL..............2-10,2-19
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION.....................Intro.-1
LAMP - DESCRIPTION, READING........8L-36
LAMP - DESCRIPTION, TAIL............8L-29
LAMP - DIAGNOSIS AND TESTING, FOG . . 8L-10
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, CLEARANCE......8L-7
LAMP - INSTALLATION, DOME..........8L-34
LAMP - INSTALLATION, FOG............8L-11
LAMP - INSTALLATION, LICENSE PLATE . . 8L-22
LAMP - INSTALLATION, MARKER........8L-23
LAMP - INSTALLATION, OUTBOARD
IDENTIFICATION.....................8L-29
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-29
LAMP - INSTALLATION, READING........8L-37
LAMP - INSTALLATION, TAIL...........8L-30
LAMP - INSTALLATION, UNDERHOOD....8L-32
LAMP - INSTALLATION, VANITY.........8L-37
LAMP - OPERATION, READING..........8L-36
LAMP - OPERATION, TAIL..............8L-29
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, CLEARANCE..........8L-7
LAMP - REMOVAL, DOME..............8L-34
LAMP - REMOVAL, FOG...............8L-11
LAMP - REMOVAL, LICENSE PLATE......8L-22
LAMP - REMOVAL, MARKER...........8L-23
LAMP - REMOVAL, OUTBOARD
IDENTIFICATION
.....................8L-28
LAMP - REMOVAL, PARK/TURN SIGNAL
. . 8L-29
LAMP - REMOVAL, READING
...........8L-36
LAMP - REMOVAL, TAIL
...............8L-29
LAMP - REMOVAL, UNDERHOOD
........8L-31LAMP - REMOVAL, VANITY.............8L-37
LAMP AND SWITCH - INSTALLATION,
GLOVE BOX.........................8L-36
LAMP AND SWITCH - REMOVAL, GLOVE
BOX ...............................8L-35
LAMP MIL - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-23
LAMP MIL - OPERATION, MALFUNCTION
INDICATOR.........................8J-23
LAMP MODULE - DESCRIPTION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - INSTALLATION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - OPERATION, DAYTIME
RUNNING............................8L-9
LAMP MODULE - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP SWITCH - DESCRIPTION, BRAKE....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE......................8L-5
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-6
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP UNIT - ADJUSTMENTS, FOG.......8L-13
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, FOG.......8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-22
LAMP UNIT - INSTALLATION, PARK/
TURN SIGNAL.......................8L-29
LAMP UNIT - INSTALLATION, TAIL.......8L-30
LAMP UNIT - INSTALLATION,
UNDERHOOD........................8L-32
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, FOG...........8L-12
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-22
LAMP UNIT - REMOVAL, PARK/TURN
SIGNAL............................8L-29
LAMP UNIT - REMOVAL, TAIL...........8L-30
LAMP UNIT - REMOVAL, UNDERHOOD . . . 8L-32
LAMPS, SPECIFICATIONS - EXTERIOR.....8L-4
LAMPS, SPECIFICATIONS - INTERIOR....8L-33
LASH ADJUSTMENT AND VERIFICATION
- STANDARD PROCEDURE, VALVE.......9-141
LATCH - ADJUSTMENT, FRONT DOOR....23-73
LATCH - INSTALLATION....23-102,23-65,23-73
LATCH - INSTALLATION, SAFETY.......23-104
LATCH - LOWER - INSTALLATION........23-80
LATCH - LOWER - REMOVAL...........23-80
LATCH - REMOVAL........23-102,23-65,23-72
LATCH - REMOVAL, SAFETY...........23-104
LATCH - UPPER - INSTALLATION........23-81
LATCH - UPPER - REMOVAL............23-81
LATCH AND KEEPER - INSTALLATION,
BACKLITE.........................23-146
LATCH AND KEEPER - REMOVAL,
BACKLITE.........................23-146
LATCH HANDLE - INSTALLATION........23-66
LATCH HANDLE - REMOVAL............23-66
LATCH RELEASE CABLE - INSTALLATION . 23-103
LATCH RELEASE CABLE - REMOVAL....23-103
LATCH STRIKER - INSTALLATION . 23-103,23-66,
23-73
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-112
LATCH STRIKER - LOWER -
INSTALLATION
.......................23-82
LATCH STRIKER - LOWER - REMOVAL
....23-82
LATCH STRIKER - REMOVAL
.....23-103,23-66,
23-73
LATCH STRIKER - REMOVAL, GLOVE
BOX
..............................23-111
LATCH STRIKER - UPPER -
INSTALLATION
.......................23-82
LATCH STRIKER - UPPER - REMOVAL
....23-82
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID
....21-101,21-273
LEAK DETECTION PUMP - DESCRIPTION
. . 25-34
LEAK DETECTION PUMP - INSTALLATION
. 25-34
LEAK DETECTION PUMP - OPERATION
....25-34
LEAK DETECTION PUMP - REMOVAL
.....25-34
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE
..............14-2
LEAK VACUUM TEST - DIAGNOSIS AND
TESTING, FUEL SYSTEM AIR
...........14-57LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE . . . 9-64,9-9
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD...............9-106,9-50
LEAKAGE - DIAGNOSIS AND TESTING,
POWER STEERING GEAR..............19-16
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-33
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM.........11-18
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-5
LEAKS - DIAGNOSIS AND TESTING,
ENGINE OIL......................9-43,9-99
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-78
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-43
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-9
LEFT FRONT FENDER - INSTALLATION....23-93
LEFT FRONT FENDER - REMOVAL.......23-93
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-157,21-327
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-15
LEVEL - STANDARD PROCEDURE,
ENGINE OIL.........................9-178
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-57
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-16
LEVEL CHECK - STANDARD
PROCEDURE, FLUID...........21-157,21-328
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL..............14-7,14-77
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL..................14-8
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL................14-7,14-77
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL......................14-7
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - INSTALLATION,
WASHER FLUID......................8R-8
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-7
LEVEL SWITCH - REMOVAL, WASHER
FLUID..............................8R-8
LEVER - ADJUSTMENT, SHIFT . . . 21-463,21-500
LEVER - INSTALLATION, GEAR SHIFT.....19-15
LEVER - INSTALLATION, SHIFT . . . 21-462,21-500
LEVER - REMOVAL, GEAR SHIFT........19-14
LEVER - REMOVAL, SHIFT......21-462,21-499
LICENSE PLATE LAMP - INSTALLATION . . . 8L-22
LICENSE PLATE LAMP - REMOVAL.......8L-22
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-22
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-22
LID - INSTALLATION, CENTER CONSOLE . 23-132
LID - REMOVAL, CENTER CONSOLE.....23-131
LIFTERS - CLEANING, HYDRAULIC....9-37,9-92
LIFTERS - INSTALLATION, HYDRAULIC....9-37,
9-92
LIFTERS - REMOVAL, HYDRAULIC....9-37,9-92
LIFTERS/TAPPETS - CLEANING, SOLID....9-164
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-165
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-165
LIFTERS/TAPPETS - REMOVAL, SOLID....9-164
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - INSTALLATION,
CIGAR...........................8W-97-4
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-3
LINE - INSTALLATION, LIQUID
..........24-52
LINE - INSTALLATION, SUCTION AND
DISCHARGE
.........................24-52
LINE - REMOVAL, LIQUID
..............24-52
LINE - REMOVAL, SUCTION AND
DISCHARGE
.........................24-51
LINE COUPLERS - DESCRIPTION, A/C
....24-40
18 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page