2002 CADILLAC ESCALADE mirror controls

ii
Table of Contents
Windows
Keys and Door Locks
Remote Keyless Entry System
Liftgate
Automatic Transmission
Parking Brake
Tilt Wheel
Turn Signal/Multifunction Lever
Windshield Wipers
Cruise Control
Exterior and Interior LampsMirrors
Storage Compartments
Convenience Net
Accessory Power Outlets
OnStar® System (If Equipped)
Sunroof (If Equipped)
HomeLink® Transmitter
Instrument Panel, Warning Lights and Gages
Secondary Information Center (SIC)
Ultrasonic Rear Parking Assist (URPA) Seats and Seat Controls
Safety BeltsAir Bag Systems
Restraint Systems for Children
Section
1
Section
2
Seats and Restraint Systems
Features and Controls

1-4 Power Lumbar Control
Your vehicle's power
lumber controls are
located near the power
seat controls. You can
increase or decrease lumbar
support in an area of the
lower seatback with the
lumber controls.
To increase support, press and hold the front of the
control. To decrease support, press and hold the rear
of the control. Let go of the control when the lower
seatback reaches the desired level of support.
You can also reshape the side wing area of the lower
seatback for more lateral support.
To increase support, press and hold the top of the
control. To decrease support, press and hold the
bottom of the control. Let go of the control when the
lower seatback reaches the desired level of support.
Memory Seat and Memory Mirrors
The memory function controls are located on the driver's
door trim panel.
For this function to work, it must be enabled/configured
in the secondary information center. See ªSecondary
Information Centerº in the Index for more information.
These controls are used to program and recall the memory
settings for the driver's seat and both the driver's and
the passenger's outside mirrors. The seat and mirror
positions can be personalized for both driver 1 and driver 2.

1-5
In addition, you can also store the seat exit position for
driver 1 and driver 2. See ªMemory Seat Exitº later in this
section for more information.
The memory function does not store the lumbar or the
side wing positions.
To store your memory seat and mirror positions,
do the following:
1. Adjust the driver's seat and both outside mirrors to
your desired position.
2. Press and hold the 1 or 2 (driver 1 or 2) button of
the memory control for three seconds. When you
hear a chime ring two times, the memory positions
are stored.
To do the same thing for a second driver, follow the
preceding steps, but press the other number of the
memory control. The memory recall feature only works
when the transmission is in PARK (P).
To recall memory seat and mirror positions, make sure
your vehicle is in PARK (P), then press the 1 or 2 button
of the memory control to recall the seat setting. You will
hear a chime ring one time to let you know the setting
has been selected.
The memory seat and mirror positions can also be
programmed to work with the keyless entry system.
See ªSecondary Information Centerº in the Index for
more information.Memory Seat Exit
For this function to work, it must be enabled in the
secondary information center. See ªSecondary
Information Centerº in the Index for more information.
By moving the seats to a stored exit position, the
memory seat exit feature can make it easier to leave the
vehicle. To store the seat exit position for driver 1 or
driver 2, do the following:
1. Select the desired driver number by pressing
the 1 or 2 button.
2. Move the seat to the desired position.
3. Press and hold the Exit button of the memory
control for three seconds. When you hear a chime
ring two times, the exit position is stored for the
identified driver (driver 1 or 2).
To use the exit feature, press the Exit button on the
memory seat controls. If you have the exit feature
enabled in the secondary information center, then
removing the key from the ignition will cause the seat to
move to the preset exit position without having to press
the Exit button. See ªSecondary Information Centerº in
the Index for more information.

1-6
Keyless Entry Transmitter Seat and Mirror
Memory Recall
For this function to work, it must be enabled in the
secondary information system. See ªSecondary
Information Centerº in the Index for more information.
You can program both of your keyless entry transmitters
to work the settings you have chosen for driver 1 or
driver 2. Once a transmitter is programmed, pressing
the UNLOCK button will recall the memory functions
chosen for that transmitter. To match a transmitter
do the following:
1. Press and hold the desired number button (1 or 2)
on the memory controls until the seat and mirror
positions are set. You will hear a chime ring twice.
Continue holding the number button.
2. While still holding the memory number button,
press UNLOCK on the keyless entry transmitter
(within five seconds) that you want to match with the
specific memory number button (1 or 2) you pressed
in Step 1.
That transmitter will now be matched with the memory
number button 1 or 2 and the memory settings that are
set for that number.Heated Front Seats
The button for the
driver's side heated seat
is located on the driver's
side door panel.
The button for the passenger's side heated seat is located
on the passenger's side door panel. The ignition must be
in RUN for this feature to operate.
To activate the heated seats, press the button once for
the HI heat setting. Press the button again for the LO
heat setting. To turn off the heated seats, press the
button a third time. An indicator light on the button will
illuminate for each heat setting anytime the heated seats
are operating.
The heated front seats will be canceled after the ignition
is turned to OFF. If you still want to use the heated front
seat feature after you restart your vehicle, you will need
to press the heated seat button again.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-4 Keys
2
-6 Door Locks
2
-8 Keyless Entry System
2
-12 Liftgate/Liftglass
2
-13 Theft
2
-14 Content Theft-Deterrent
2
-15 Passlock

2-16 New Vehicle ªBreak-Inº
2
-16 Ignition Positions
2
-17 Starting Your Engine
2
-19 Engine Coolant Heater (If Equipped)
2
-20 Automatic Transmission Operation
2
-24 Parking Brake
2
-25 Shifting Into PARK (P)
2
-27 Shifting Out of PARK (P)
2
-28 Parking Over Things That Burn
2
-28 Engine Exhaust2
-29 Running Your Engine While You're Parked
2
-30 Locking Rear Axle
2
-31 Turn Signal/Multifunction Lever
2
-37 Exterior Lamps
2
-41 Interior Lamps
2
-43 Mirrors
2
-49 Storage Compartments
2
-57 Analog Clock
2
-58 OnStar
System (If Equipped)
2
-61 Sunroof (If Equipped)
2
-62 HomeLink
Transmitter
2
-66 The Instrument Panel - Your
Information System
2
-68 Instrument Panel Cluster
2
-69 Warning Lights, Gages and Indicators
2
-83 Message Center
2
-91 Secondary Information Center (SIC)
2
-97 Ultrasonic Rear Parking Assist (URPA)

2-46
To adjust for compass variance do the following:
1. Use the COMP button located at the bottom of
the mirror.
2. Press and hold the COMP button for three seconds
until a zone number appears in the display.
3. Find your current location and variance zone number
on the following zone map.4. Press the COMP button on the bottom of the mirror
until the new zone number appears in the display.
After you stop pressing the button in, the display
will show a compass direction within a few seconds.
Electric Outside Rearview Mirrors (Heated)
The controls for the mirrors
are located on the driver's
door armrest.
Move the upper control to the left or right to choose the
mirror you want to adjust, then press the arrows located
on the lower control to adjust the mirror in the direction
you want the mirror to go.
The mirrors include ground illumination lamps (puddle
lamps) in the base of the mirror. These lamps will light
the area near the front doors. The lamps are activated
when the remote keyless entry is operated, or the door
handle is pulled. The lamps will time out or turn off
once the engine is started.

2-47
When you operate the rear window defogger, it also
warms both outside mirrors to help clear them of fog
or ice. See ªRear Window Defoggerº in the Index for
more information.
The mirrors can also be programmed for
personalization. For more information, see ªMemory
Seat and Mirrorsº and ªSecondary Information Centerº
in the Index.
Curb View Assist Mirror
For this function to work, it must be enabled in the SIC.
See ªSecondary Information Centerº in the Index for
more information.
Your vehicle is equipped with the curb view assist
mirror feature. When the vehicle is shifted into
REVERSE (R) there will be a three second delay
before the curb view assist mirror(s) tilt to a preselected
position. This feature may be useful in allowing you
to view the curb when you are parallel parking.
When the vehicle is shifted out of REVERSE (R) and a
five second delay has occurred, the selected mirrors will
return to the original position.If further adjustment is needed after the mirror is tilted,
the mirror controls may be used.
You can also adjust the angle of tilt for each outside
mirror by doing the following:
1. Place the vehicle in REVERSE (R) and allow
the mirrors to tilt (be sure this feature is enabled
in the SIC).
2. Change the angle of mirror tilt to your liking with
the mirror controls.
The mirrors are now set to the desired position.
This feature can also be disabled/configured through the
SIC. See ªSecondary Information Centerº in the Index
for more information.
Driver's Outside Auto-Dimming
Rearview Mirror
The driver's outside mirror will adjust for the glare of
any headlamps behind you. This feature is controlled
by the on and off settings on the electrochromic mirror.
See ªElectrochromic Day/Night Rearview Mirror with
Compass and Temperatureº earlier in this section.

2-67
The main components of your instrument panel are the following:
A. Dome Lamp Override Button
B. Headlamp and Parking Lamp Controls
C. Air Outlets
D. Folding Mirrors Button
E. Rear Wiper/Washer
F. Turn Signal/Multifunction Lever
G. Instrument Panel Cluster
H. Shift Lever
I. Tow/Haul Mode Selector Button
J. Audio System
K. Comfort Control System
L. Instrument Panel Fuse Block
M. Hood Release
N. Fog Lamps ButtonO. Audio Steering Wheel Controls
P. Center Instrument Panel Utility Block
Q. Tilt Lever
R. Parking Brake Release
S. Secondary Information Center (SIC)
T. Rear Window Defogger Button
U. Compact Disc Changer
V. Ashtray
W. Clock
X. Ultrasonic Rear Parking Assist Button
Y. StabiliTrak

Button (AWD)/Traction
Control Button (2WD)
Z. OnStar Buttons