2002 CADILLAC ELDORADO light

2-76 Oil Pressure Light
CAUTION:
Don't keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.
This light tells you if there
could be a problem with
your engine oil pressure.
The light goes on when you turn your key to RUN
or START. It goes off once you start your engine.
That's a check to be sure the light works. If it doesn't
come on, be sure to have it fixed so it will be there to
warn you if something goes wrong.
When the light comes on and stays on, it means
that oil isn't flowing through your engine properly.
You could be low on oil and you might have some
other system problem.

2-77 Security Light
This light works with
the PASS
-Key II system.
See ªPASS
-Key IIº in the
Index for more information.
Fuel Gage
The fuel gage shows
approximately how much
fuel is in the tank. It works
only when the ignition is
in RUN.Here are a few concerns some owners have had about
the fuel gage. All of these situations are normal and do
not indicate that anything is wrong with the fuel gage.

At the gas station the gas pump shuts off before
the gage reads full.

It takes more (or less) gas to fill the tank than the
gage said. For example, the gage read half a tank,
but it took more (or less) than the tank's remaining
capacity to fill it.

The gage may change when you turn, stop or
speed up.
Fuel Data Display
Everything you need to know about the fuel
economy and how far you can travel with your
vehicle's remaining fuel is displayed on the Driver
Information Center (DIC). Fuel data can be
obtained by pressing the SKIP INFO button
located on the instrument panel above the audio
system. See ªDIC Controls and Displaysº later
in this section for more information.

2-81
If this message appears and stays on while driving or
after starting your vehicle, have it checked immediately
to determine the cause of this problem. To help the
generator recharge the battery quickly, you can reduce
the load on the electrical system by turning off the
accessories. You can monitor battery voltage on the
DIC by pressing the SKIP INFO button. The normal
range is 11.5 to 15.5 volts.
CHANGE ENGINE OIL
- 82: This means that
the life of the engine oil has expired and it should be
changed within 200 miles (322 km). See ªEngine Oilº
in the Index. After an oil change, the Oil Life Indicator
must be reset. See ªOil Life Indicator, How to Resetº
in the Index.
CHANGE TRANS FLUID
- 47: This message will
appear when it is time to replace the transaxle fluid.
See ªMaintenance Scheduleº in the Index for the proper
fluid and change intervals.CHECK BRAKE FLUID LEVEL
- 37: This message
will display if the ignition is in RUN to inform the
driver that the brake fluid level is low. Have the brake
system serviced by a technician as soon as possible.
See ªBrake System Warning Lightº in the Index.
CHECK COOLANT LEVEL
- 2: This message
will appear when there is a low level of engine coolant.
Have the cooling system serviced by a technician as
soon as possible.
CHECK FUEL GAUGE
- 39: This message will
appear when the fuel supply is less than 3.5 gallons
(13.2 L) remaining. A single chime will also sound
when this message is displayed.
CHECK GAS CAP
- 61: This message will appear
if the gas cap has not been fully tightened. You should
recheck your gas cap to ensure that it's fully tightened.

2-83
ENGINE HOT - A/C OFF - 16: This message
displays when the engine coolant becomes hotter than
the normal operating temperature. To avoid added strain
on a hot engine, the air conditioning compressor is
automatically turned off so that air conditioned air is
not delivered. If the coolant temperature returns to
normal, you must select AC to return to a normal A/C
compressor operation. If this message continues to
appear, have the system repaired as soon as possible to
avoid compressor damage.
ENGINE MISFIRE
-- EASE OFF GAS
PEDAL
- 114: An engine misfire has occurred.
You'll need to ease off the gas pedal.
ENGINE OVERHEATED, STOP ENGINE
- 42:
This message will appear when the engine has overheated.
Stop and turn the engine off immediately to avoid severe
engine damage. See ªEngine Overheatingº in the Index.
A multiple chime will also sound when this message
is displayed.
ENGINE POWER REDUCED
- 41: This message
informs you that your vehicle is reducing engine power
because the transaxle is being placed in gear under
conditions that may cause damage to the vehicle
powertrain or vehicle acceleration.FUEL LEVEL LOW
- 11 : This message serves as
a warning that the fuel level in the tank is critically low.
Stop for fuel soon.
HEADLAMPS SUGGESTED
- 23: If it's dark enough
outside and Twilight Sentinel is off, a HEADLAMPS
SUGGESTED message will display on the DIC.
This message informs the driver that turning on the
exterior lamps is recommended even though the
Daytime Running Lamps (DRL) are still illuminated
(it's become dark enough outside to require the
headlamps and/or other exterior lamps).
ICE POSSIBLE
- 13: This message appears when
the outside air temperature is cold enough to create icy
road conditions.
LOW REFRIG A/C OFF
- 12: This message means
that the air conditioning system detects a refrigerant
level that is low enough to cause damage to the air
conditioning compressor. Have the air conditioning
system serviced if this message appears.
MONITORED SYSTEMS OK
- 1: This message only
appears in the ªrecallº mode by pressing the NO INFO
RESET button. It lets you know that no other messages
are stored or are currently active.

2-84
OIL PRESSURE LOW STOP ENGINE - 35: If this
message appears while the engine is running, stop the
engine and do not operate it until the cause of low oil
pressure is corrected. Severe damage to the engine can
result. A multiple chime will also sound when this
message is displayed.
OPTIONS NOT SET
- 99: This message will display
if a fault has occurred in your vehicle's memory.
Have your vehicle serviced by your dealership.
PROGRAM PASS KEY
- 31: This warning message
displays when the PASS
-Key
II pellet information
has not been programmed into your vehicle. See your
dealership for service.
REMOVE KEY
- 70: This message will appear when
the PASS
-Key
II system is unable to read the pellet
on the ignition key or an improper key pellet has been
inserted. This message usually appears following the
display of STARTING DISABLED REMOVE KEY.
The instrument panel cluster will then run a timer and
change the messages to WAIT 3 MINUTES, WAIT
2 MINUTES, WAIT 1 MINUTE and then START CAR.
When the REMOVE KEY message is displayed, remove
the ignition key. Check the ignition key for damage. If it is damaged, it may need to be replaced. If you see
no damage, clean the pellet contacts with a soft cloth or
napkin before inserting the key back into the ignition.
Have your vehicle serviced if the message still appears.
SERVICE A/C SYSTEM
- 14: This message
appears when the electronic sensors that control the air
conditioning and heating systems are no longer working.
Have the climate control system serviced if you notice a
drop in heating and air conditioning efficiency.
SERVICE AIR BAG
- 83: There is a problem with
the Supplemental Inflatable Restraint (air bag) system
when this message appears. Let only a qualified
technician work on your vehicle. See your dealership
for service at once.
SERVICE BRAKE FLUID SWITCH
- 37: A problem
in the brake fluid detection circuit causes this message
to display if the ignition is in RUN. Have the brake
system serviced by a technician as soon as possible.
If the brake warning light is on, refer to the directions
listed in that part.

2-90
Lock/Unlock Confirmation
This personalization feature allows the driver to program
the parking lamps to flash when the buttons on the
remote keyless entry transmitter are pressed, to program
the horn to sound when the button with the lock symbol
is pressed and/or to program the exterior lamps to turn on
when the button with the unlock symbol is pressed on the
remote keyless entry transmitter.
Programmable Modes
Mode 1 (LGHTS FLSH AT UNLOCK): Parking
lamps flash twice when the button with the unlock
symbol on the remote keyless entry transmitter is pressed.
Mode 2 (LIGHTS FLASH AT LOCK): Parking lamps
flash once when the button with the lock symbol on the
remote keyless entry transmitter is pressed.
Mode 3 (HORN SOUNDS AT LOCK): Horn sounds
when the button with the lock symbol on the remote
keyless entry transmitter is pressed.Mode 4 (EXT LIGHTS AT UNLOCK): Exterior
lamps turn on when the button with the unlock symbol
on the remote keyless entry transmitter is pressed
and it is dark outside. These lamps stay on for about
20 seconds or until the key is turned to OFF.
Before your vehicle was shipped from the factory, it was
programmed to enable Mode 1 and Mode 2. The modes
to which the vehicle was programmed may have been
changed since it left the factory. To determine the modes
to which the vehicle is programmed or to program the
vehicle to different modes, do the following:
1. Enter feature programming following the
instructions listed previously.
2. Press the SKIP INFO button until LOCK/UNLOCK
appears on the display.
3. Press YES TRIP RESET to select this feature for
programming. Mode 1 described previously will
appear on the display once a yes response is made.

2-91
4. A yes or no response must be made after each mode
is displayed in order to continue to the next mode.
Press the YES TRIP RESET button to indicate yes,
or press the NO INFO RESET button to indicate no.
Once you have indicated the mode that you want
with a yes response, FEATURE ON will appear on
the display. FEATURE OFF appears when you
indicate a no response, and the display will advance
to the next mode.
REMOTE RECALL MEMORY will appear
once a mode has been selected for lock/unlock
confirmation feature.
If you press the SKIP INFO button, the menu will
advance to the next feature available for programming.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Remote Recall Memory (If Equipped with
Memory Personalization)
Memory settings that have been previously programmed
(climate control settings, radio preset settings, exterior
lighting choices, remote confirmation choices and
programmable automatic door lock choices) can be
recalled by using the remote keyless entry transmitter
or by placing the key in your vehicle's ignition.
Programmable Modes
Mode 1 (REMOTE RECALL MEMORY):
The previously programmed driver's seat and mirror
positions are automatically recalled when the button
with the unlock symbol on the remote keyless entry
transmitter is used to unlock the vehicle.
Mode 2 (KEY IN RECALL MEMORY):
The previously programmed driver's seat and mirror
positions are automatically recalled when the ignition
is turned to RUN.

3-7 Air Conditioning
On hot days, open the windows long enough to let hot
inside air escape. This reduces the time it takes for your
vehicle to cool down. Then keep your windows closed
for the air conditioner to work its best.
Press the AC button or the TEMP/AUTO knob to turn
the system on and then select the proper mode to direct
airflow. The system will cool and dehumidify the air
inside the vehicle. Also while in the AUTO mode, the
system will use recirculation as necessary to cool the air.
You may also need to adjust the interior temperature and
the fan speed as needed.
When the air conditioner is on, you may sometimes
notice slight changes in your vehicle's engine speed
and power. This is normal because the system is
designed to cycle the compressor on and off to
maintain the desired temperature.
Heating
Press the MODE switch to select the heater mode.
Adjust the interior temperature to a comfortable level
and if the fan speed needs adjusting, press the up or
down arrow.
Outside air will be brought in and sent through the floor,
air conditioning or bi
-level outlets (depending on the
condition). The heater works best if you keep your
windows closed while using it.
Defogging and Defrosting
Use defrost to remove fog or ice from the windshield
quickly in extremely humid or cold conditions.
Press the MODE switch. If you select defrost mode,
adjust the fan speed by pressing the fan switch up or
down. If you select defrost mode from AUTO, the
system will control the fan speed. The temperature also
needs to be adjusted by turning the TEMP/AUTO knob.
Recirculation is not available in the defrost or defog modes.