2002 BUICK LESABRE instrument panel

2-92
Head-Up Display (HUD)
(If Equipped)
CAUTION:
If the HUD image is too bright, or too high in
your field of view, it may take you more time to
see things you need to see when it's dark outside.
Be sure to keep the HUD image dim and placed
low in your field of view.
If your vehicle is equipped with the Head-Up Display
(HUD), you can see some of the driver information
that appears on your instrument panel cluster.
The information may be displayed in English or metric
units and appears as a reflection in the windshield.
The HUD consists of the following information:

Speedometer Reading

Turn Signal Indicators

High
-Beam Headlamp Indicator

Check Gages Message
The HUD shows these images when they are lighted on
the instrument panel cluster.

2-93
Be sure to continue scanning your displays, controls and
driving environment just as you would in a vehicle
without HUD. If you never look at your instrument
panel cluster, you may not see something important,
such as a warning light.
NOTICE:
Although the HUD image appears to be near the
front of the vehicle, do not use it as a parking aid.
The HUD was not designed for that purpose. If
you try to use the display as a marker for the
front of your vehicle, such as in a parking lot, you
may misjudge distance and hit an obstacle or
another vehicle.
The HUD controls are located on the instrument panel to
the left of the steering wheel.
1. Start your engine and slide the HUD dimmer lever
all the way up.
The brightness of the HUD image is determined by
an internal photo
-cell, and where you have the HUD
dimmer control set.
2. Adjust the seat to your driving position. Press the
image height adjuster switch to raise the image as far
as possible.

3-2
Comfort Controls
This section describes how to operate your climate
control system. With this system, you can control the
heating, cooling and ventilation in your vehicle.
Your vehicle also has a flow
-through ventilation system
described later in this section.
Electronic Touch Climate Control
Fan Lever
The FAN lever is used to select the speed of the fan.
Moving the lever between LOW and HIGH will
decrease or increase the fan speed. The fan will be
off when the system is off.Temperature Lever
This lever is used to adjust the temperature of the air
coming through the system. Move the TEMPERATURE
lever between COOL and WARM to change the
temperature of the air coming through your outlets.
Mode Controls
The buttons on your system allow you to choose settings
to deliver air through the floor ducts, instrument panel
outlets or windshield outlets.
RECIRC (Recirculation): Press this button to limit the
amount of outside air entering your vehicle. This is
helpful when you are trying to cool the interior of the
vehicle quickly, or limit the amount of outside air
entering your vehicle. To turn off RECIRC, press the
button again. If you select FRONT defrost or BLEND
while RECIRC is selected, the system will automatically
turn off RECIRC to prevent fogging. If you select
RECIRC while in FRONT defrost, the RECIRC light
will flash three times to let you know this is not allowed.

3-3
VENT: This setting directs outside air through the
instrument panel outlets. The air conditioning
compressor is not working when VENT is selected. If
you select VENT while in FRONT defrost, the VENT
light will flash three times to let you know this is not
allowed. This is to prevent fogging.
HTR (Heater): This setting directs most of the air
out of the floor ducts while some air will flow through
the windshield and side window outlets. The air
conditioning compressor is not working when
HTR is selected.
BLEND: When BLEND is selected, the airflow will be
split between the windshield outlets and the floor ducts.
The air conditioning compressor will be operating.
FRONT: This setting directs most of the airflow
toward the windshield.
OFF: The ventilation system always allows fresh air to
flow through your vehicle when it is moving. The
system will try to keep the air at a previously chosen
temperature. When the system is off, the blower fan is
also off.MAX (Maximum Air Conditioning): This setting
directs airflow through the instrument panel outlets. The
amount of outside air entering your vehicle is limited
with this setting. The air conditioning compressor is on
in this mode.
Also in this mode, the RECIRC function is activated
to create the maximum cooling effect in the vehicle. If
RECIRC was active before selecting MAX, the light in
the RECIRC button will go off. If RECIRC is selected
after MAX, the light in the RECIRC button will not
come on.
NORM (Normal): This setting cools the outside
air entering your vehicle and directs it through the
instrument panel outlets. The air conditioning
compressor is on in this mode.
BI
-LEV (Bi-Level): This setting directs warmer air
to the floor ducts and cooler air to the instrument panel
outlets. The air conditioning compressor is on in
this mode.

3-4 Dual Automatic ComforTemp
Climate Control (If Equipped)
TEMP (Temperature): To manually adjust the
temperature inside the vehicle, push the TEMP arrow.
Push the TEMP up arrow for warmer temperature
settings and the TEMP down arrow for cooler
temperature settings. The setting will be shown in the
display. The display will then return to the outside
temperature after a few seconds.
FAN: Pressing the FAN button will display and
hold the current fan speed while in manual mode.If you want the fan to run at a lower speed, push the
down arrow on the FAN button. The fan speed will
decrease with every push of the button until the lowest
speed is reached. If you want to increase the fan speed,
push the up arrow on the FAN button.
AIR FLOW: Pressing the AIR FLOW button will
display and hold the current setting while in manual
mode. Use the up and down arrows on the AIR FLOW
button to cycle through the available modes.

WINDSHIELD
-FLOOR: This setting directs
most of the airflow to the front windshield defroster
with some airflow to the side window defrosters and
floor ducts.

MID: This setting directs airflow through the
instrument panel outlets.

MID
-FLOOR: This setting directs airflow through
both the instrument panel outlets and the floor ducts.
There is also a small amount of air directed to the
front defroster and the side window defrosters.

FLOOR: This setting directs most of the airflow to
the floor ducts with some airflow directed to the side
window defrosters. There is also a small amount of
airflow directed to the front defroster.

3-6 Passenger Climate Control (If Equipped)
If your vehicle is equipped with the Dual Automatic
ComforTemp system, the front seat passenger can
control the air temperature in his or her seating area. The
control is located on the passenger's door armrest.The temperature can be set up to 5
F (3
C) cooler
or warmer than the primary setting. To activate the
passenger control, press the button with the red arrow
to increase temperature. Each time you press the button, a
red indicator light will come on. To decrease temperature,
press the button with the blue arrow. Each time you press
the button a blue indicator light will come on.
If the passenger control has been turned on, it can be
turned off by pressing the OFF button on the main
system once. (Pressing the OFF button a second time
will turn off the main system.)
Automatic Operation
Press the AUTO button when you want the system to
automatically maintain a selected temperature inside of
your vehicle. When the system is set for automatic
operation, air will come from the floor ducts, instrument
panel outlets or windshield outlets depending on the
temperature inside the vehicle, the outside temperature
and sun load. Fan speed and use of air conditioning and
recirculation will vary as needed.

3-9
On sunny days, when the air is moderately warm or
cool, use Bi
-Level to deliver warm air to the floor ducts
and cooler air to the instrument panel outlets. On days
like these, the sun may adequately warm your upper
body, but your lower body may not be warm enough.
To warm or cool the air delivered, adjust the
TEMPERATURE lever.
The amount of fresh air entering the vehicle is limited
when Recirculation is selected. This is helpful when you
are trying to cool the air in your vehicle or limit the air
entering the vehicle.
If your vehicle has the Dual Automatic ComforTemp
system and it is set for Automatic Operation, on very hot
days, the system will automatically enter recirculation
mode and the temperature door will be positioned at the
full cold position for maximum cooling. If the system is
not in the automatic mode, recirculation should be
selected to provide maximum cooling. You can choose
the extreme comfort setting of 60
F (16
C), but the
system will not cool any faster as a result.Heating
If your vehicle has the electronic touch system, on cold
days, use HTR with the TEMPERATURE lever toward
WARM and the fan speed toward HIGH.
If your vehicle has the Dual Automatic ComforTemp
system, and on cold days, if the automatic mode is
selected, the system will automatically direct the air
toward the floor and the temperature door will be
positioned at the full hot position. You can choose the
extreme comfort setting of 90
F (32
C) but the
system will not warm up any faster as a result. If the
outside temperature is cold, the fan will be delayed to
avoid blowing cold air. Pushing the FAN, AIR FLOW
or FRONT buttons will override this delay, turn off
the automatic mode and return the system to
manual operation.
With each system, outside air will be brought in and sent
through the floor ducts. The heater works best if you
keep your windows closed while using it.

3-11
NOTICE:
Do not try to clear frost or other material from
the inside of the rear window with a razor blade
or anything else that is sharp. This may damage
the rear defogger grid. The repairs wouldn't be
covered by your warranty.
Do not attach a temporary vehicle license, tape or decals
across the defogger grid on the rear window.
Ventilation System
For mild outside temperatures when little heating
or cooling is needed, use VENT (on the electronic
touch system or manual operation on the Dual
Automatic ComforTemp
system) to direct
outside air through your vehicle. Air will flow
through the instrument panel outlets.
Your vehicle's flow
-through ventilation system supplies
outside air into the vehicle while it's moving. While the
vehicle is not moving, you can get outside air to flow
through by selecting any air choice (except the rear
window defogger) and any fan speed.
Adjust the direction of
airflow by moving the
louvered vents.
If you have the optional rear
passenger ComforTemp,
you can adjust the direction
of the airflow to the rear
seating area.