2002 BUICK CENTURY display

2-25
B (LOCK): This is the only position in which you
can insert or remove the key. This position locks the
ignition, steering wheel and transaxle. It's a
theft
-deterrent feature.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key;
if so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. Turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.
C (OFF): This position lets you turn off the engine but
still turn the steering wheel. It doesn't lock the steering
wheel. Use OFF if you must have your vehicle pushed
or towed.D (RUN): This position is where the key returns to
after you start your vehicle. With the engine off, you
can use RUN to display some of your warning and
indicator lights.
E (START): This position starts your engine.
A warning chime will sound if you open the driver's
door when the ignition is in OFF, LOCK or
ACCESSORY and the key is in the ignition.
Retained Accessory Power (RAP)
(If Equipped)
With Retained Accessory Power (RAP), your
power windows, audio system and sunroof (if equipped)
will continue to work for up to 10 minutes after the
ignition key is turned to OFF and before any of the
doors are opened.

2-28
4. Before starting the engine, be sure to unplug
and store the cord as it was before to keep it away
from moving engine parts. If you don't, it could
be damaged.
How long should you keep the coolant heater plugged
in? The answer depends on the outside temperature, the
kind of oil you have, and some other things. Instead of
trying to list everything here, we ask that you contact
your dealer in the area where you'll be parking your
vehicle. The dealer can give you the best advice for
that particular area.Automatic Transaxle Operation
Your automatic transaxle will have a shift lever on the
steering column.
The graphic shown above is displayed on your
instrument panel cluster in reference to your steering
column shift lever.
Maximum engine speed is limited on automatic
transaxle vehicles when you're in PARK (P) or
NEUTRAL (N) to protect driveline components
from improper operation.

3-4 Dual Automatic ComforTemp
Climate
Control (If Equipped)
With this system, you set a temperature. You can
then either let the system automatically control airflow
direction and force to maintain the temperature, or you
can manually adjust it. The system works best if you
keep your windows closed while using it.
Manual Control
If you prefer to manually control the heating,
cooling and ventilation in your vehicle, you can
select airflow direction, fan speed, outside or
recirculated air, air compressor and temperature
operation with the following:AIR FLOW: This control has several settings to
control the direction of airflow when the system is
not in AUTO.
To access the various modes available, continue to press
the AIR FLOW rocker switch up or down until the
desired mode appears in the display:
WINDSHIELD/FLOOR: This setting directs half
of the air to the floor ducts and half to the defroster
and side window vents. The air conditioning
compressor will run automatically in this setting
unless the outside temperature is below 40
F (4
C).
MID/FLOOR (Instrument Panel/Floor): This
setting directs half of the air through the instrument
panel outlets. Most of the remaining air is directed
through the floor ducts
and a little to the defroster and side window vents.
MID (Instrument Panel): This setting directs air
through the instrument panel outlets.
FLOOR: This setting sends most of the air through
the ducts near the floor. The rest comes out of the
defroster and side window vents. When in this
setting and the RECIRC setting, the windows can
fog up. See ªRECIRCº in the Index.

3-5
FAN: Press the up arrow to increase fan speed and
the down arrow to decrease fan speed. The fan must be
turned on for the air conditioning compressor to operate.
TEMP (Temperature): The TEMP switch sets the
temperature for the entire cabin when the light on the
DUAL light button isn't lit. When the DUAL button
light is lit, the TEMP switch sets the temperature for the
driver only. Press the up arrow to raise the temperature
and press the down arrow to lower the temperature. The
display will show your selection for a few seconds, then
the outside temperature will be displayed. If you push
the AUTO button, the system will control the fan speed
and airflow and will maintain the selected temperature.
VENT: This setting turns the air conditioning
compressor on and off. The indicator is lit when the
compressor is turned off. Recirculation is not permitted
when the compressor is off. The system will try to
control the temperature automatically, but without
the compressor.
VENT is not permitted in FRONT defrost mode. If the
VENT button is pushed while in FRONT defrost mode,
the indicator will light briefly and then turn off.RECIRC (Recirculation): This setting recirculates
much of the air inside your vehicle. This setting is
not permitted in FRONT defrost mode and is only
permitted in WINDSHIELD/FLOOR mode if the
compressor is turned on. The indicator light will be
lit when recirculation is engaged, but will light briefly
and then turn off if selected when not permitted.
Operating the climate control system in the RECIRC
mode may cause fogging of the vehicle's windows
when the weather is cold and damp. To clear the fog,
switch the system to either WINDSHIELD/FLOOR
or WINDSHIELD mode and increase the fan speed.
To avoid re
-fogging of the windows, operate the
system with RECIRC off.
FRONT: This setting brings in outside air
and directs most of the air through the defrost vent.
Some of the air also goes to the floor ducts and the
side window defogger outlets. The indicator on the
button will light and WINDSHIELD will be seen on
the display. The air conditioning compressor will run
automatically in this setting unless the outside
temperature is below 40
F (4
C).

3-6
PASSENGER Control: The PASSENGER CONTROL
buttons with the arrows adjust the temperature on the
passenger's side so it is warmer or cooler than the
temperature for the driver's side. Push the DUAL button
so that the indicator light is lit. Press the right arrow
button to raise the temperature. Press the left arrow
button to lower the temperature.
The display will not show the passenger's temperature,
only that of the driver. Indicators in the passenger
control section will show passenger's side temperature
relative to the driver's set temperature.

The amber light indicates the same temperature as
set for the driver.

The red lights indicate a warmer temperature than
that of the driver.

The blue lights indicate a cooler temperature than
that of the driver.
AUTO (Automatic Control): For the most efficient
operation, you should set the system temperature and
press AUTO. The system will then select the best fan
speed and airflow settings to keep you comfortable. The
air conditioning compressor will run if the outside
temperature is above 40F (4C). You may notice a
delay of two to three minutes before the fan comes on at
start up in cool weather.For the automatic system to function, the temperature
must be set between 61F (16C) and 89F (31C).
The driver's temperature and passenger's temperature
settings will be automatically maintained even if manual
overrides have been selected except for settings at
60F (15C) and 90F (32C).
Setting the temperature to 90F (32C) will lock
control in full hot, direct air to the floor, and increase
the fan speed to high. The system will not return to
automatic temperature control until the temperature
setting is lowered.
Setting the temperature to 60F (15C) will lock
control in full cold, recirculate interior air, direct air
to outlets on panel and increase blower speed to high.
The system will not return to automatic temperature
control until the temperature setting is raised.
OFF: Press this button to turn the air compressor off.
Heating
On cold days, use HTR with the driver and passenger
levers all the way in the red area. This system will bring
in outside air, heat it, and send it to the floor ducts.

3-7 Heating (Engine Coolant Heater)
If your vehicle has an engine coolant heater, you can use it
to help your system provide warm air faster when it's cold
outside
-- 0
F (-18
C) or lower. An engine coolant heater
warms the coolant your engine and heating system use to
provide heat. See ªEngine Coolant Heaterº in the Index.
Air Conditioning
On very hot days, open the windows long enough to let
hot, inside air escape. This reduces the time for the
vehicle to cool down.
For a quick cool
-down on very hot days, use MAX with
the temperature levers all the way in the blue area. If
this setting is used for long periods of time, the air in
your vehicle may become too dry.
For normal cooling on hot days, use VENT with the
temperature levers in the blue area. The system will
bring in outside air and cool it.
On cool, but sunny days, the sun may warm your upper
body, but your lower body may not be warm enough.
You can use BI
-LEV and set the temperature levers to a
comfortable setting. The system will bring in outside air
and direct it to your upper body, while sending slightly
warmed air to your lower body. You may notice this
temperature difference more at some times than others.
Push the A/C button for cooling.
Defogging and Defrosting
If you have the Dual Comfortemp Climate Control, your
system has two settings for clearing the front and side
windows. To defrost the windows quickly, turn the mode
knob to the defrost setting and turn the temperature knob
all the way in the red area.
For maximum defroster performance, set both driver and
passenger temperature controls to the warmest setting.
To warm passengers while keeping the windows clear,
use BLEND.
If you have the Dual Automatic Comfortemp Climate
Control, your system has two settings for clearing the front
and side windows. To defrost the windows quickly, press
the FRONT button, set the temperature to 90
F (32
C),
select high fan speed and turn the DUAL button off. To
warm passengers while keeping the windows clear, push
the AIR FLOW button until WINDSHIELD/FLOOR
appears in the display. Select fan speed for comfort and
windshield clearing performance.

3-11
RECALL: Push this knob to display the station
being played or to display the clock. To change what is
normally shown on the display (station or time), push
the knob until you see the display you want, then hold
the knob until the display flashes. Push this knob when
the ignition is off, to display the clock.
Finding a Station
AM±FM: Press this button to switch between AM,
FM1 and FM2. The display shows your selection.
TUNE: Turn this knob to choose radio stations.
 SEEK
: Press the right or left arrow to go to
the next or previous station and stay there. The radio
will seek to stations with a strong signal only. The
sound will mute while scanning. The sound will mute
while seeking.
To scan stations, press one of the SEEK arrows for
two seconds, and SCAN will appear on the display.
The radio will go to a station, play for a few seconds,
then go on to the next station. Press one of the SEEK
arrows again to stop scanning. The radio will scan to
stations with a strong signal only. The sound will mute
while scanning.P SCAN (Preset Scan): Press this button to listen to
each of your preset stations for a few seconds. The radio
will go to the first preset station, play for a few seconds,
then go on to the next preset station. Press P SCAN
again to stop scanning. The radio will scan preset
stations with a strong signal only. The sound will mute
while scanning.
Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2) by performing the
following steps:
1. Turn the radio on.
2. Press the AM±FM button to select the band.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons.
The sound will mute. When it returns, release the
pushbutton. Whenever you press that numbered
pushbutton, the station you set will return.
5. Repeat the steps for each pushbutton.

3-13
RECALL: Push this knob to display the station
being played or to display the clock. To change what is
normally shown on the display (station or time), push
the knob until you see the display you want, then hold
the knob until the display flashes. Push this knob when
the ignition is off, to display the clock.
Finding a Station
AM±FM: Push this knob to switch between AM,
FM1 and FM2. The display shows your selection.
TUNE: Turn this knob to choose radio stations.
 SEEK
: Press the right or left arrow to go to the
next or previous station and stay there. The radio will
seek to stations with a strong signal only. The sound
will mute while seeking.
To scan stations, press one of the SEEK arrows for
two seconds, and SCAN will appear on the display.
The radio will go to a station, play for a few seconds,
then go on to the next station. Press one of the SEEK
arrows again to stop scanning. The radio will scan to
stations with a strong signal only. The sound will mute
while scanning.P SCAN (Preset Scan): Press this button to listen to
each of your preset stations for a few seconds. The radio
will go to the first preset station, play for a few seconds,
then go on to the next preset station. Press P SCAN
again to stop scanning. The radio will scan preset
stations with a strong signal only. The sound will mute
while scanning.
Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2) by performing the
following steps:
1. Turn the radio on.
2. Press the AM FM knob to select the band.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons.
The sound will mute. When it returns, release the
pushbutton. Whenever you press that numbered
pushbutton, the station you set will return.
5. Repeat the steps for each pushbutton.