2002 Acura RL light

Pressing the Cruise Control Master
Switch turns the system completely
of f and erases the previous cruising
speed f rom memory. To use the
system again, ref er to.
When you push the CANCEL button,
or tap the brake pedal, the CRUISE
CONTROL light on the instrument
panel will go out and the car will
begin to slow down. You can use the
accelerator pedal in the normal way.
The system remembers the
previously-set cruising speed. To
return to that speed, accelerate to
above25mph(40km/h),thenpress
and release the RESUME/accel
button. The CRUISE CONTROL
light comes on, and the car will
accelerate to the same cruising
speed as bef ore.
Using t he
Cruise Cont rol
Cruise Control
Comf ort and Convenience Feat ures161
01/09/28 19:50:47 31SZ3660_164

The HomeLink Universal
Transceiver built into your car can
be programmed to operate remotely-
controlled devices around your home,
such as garage doors, lighting, or
home security systems. It can
replaceuptothreeremote
transmitters.
If you have problems with training
the HomeLink Universal Transceiver,
or would like inf ormation on home
products that can be operated by the
transmitter, call (800) 355-3515. On
the Internet, go to www.homelink.
com.Always ref er to the operating
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with the HomeLink
Universal Transceiver. If you do not
have this inf ormation, you should
contact the manuf acturer of the
equipment.
While training or using HomeLink,
make sure you have a clear view of
the garage door or gate, and that no
one will be injured by its movement.
If you are training HomeLink to
operate a garage door or gate, it is
recommended that you unplug the
motor f or that device during
training. Repeatedly pressing the
remote control button could burn
out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your car’s battery goes dead or is
disconnected.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program
HomeLink to operate it. Garage door
openers manuf actured bef ore that
date do not have a safety feature that
causes them to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury. If you
have questions, call (800) 355-3515.
Customer Assistance
Important Saf ety Precautions General Inf ormation
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures162
01/09/28 19:50:57 31SZ3660_165

µ
If you are training the second or
third buttons, go directly to Step 1. Unplug the garage door opener
motor f rom the house current.
Bef ore you can use HomeLink to
operate devices around your home, it
must ‘‘learn’’ the proper codes. For
example, to train HomeLink to open
and close the garage door:
If you just took
delivery of your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the f irst button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 20 seconds,
until the red light f lashes. Release
the buttons, then proceed to Step 1.
Holdtheendof thegaragedoor
opener remote control 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red light in HomeLink. Select the HomeLink button you
want to train.
Press the button on the remote
control and the button on
HomeLink at the same time. Hold
down both buttons.
1.
2. 3.
4.
CONT INUED
T raining HomeL inkBef ore you begin
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures163
01/09/28 19:51:08 31SZ3660_166

For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Inf ormation f rom
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so they send and
receive the correct codes.
The remote control you are training
from may stop transmitting after two
seconds. This is not long enough f or
HomeLink to learn the code. Release
and press the button on the remote
control every two seconds until
HomeLink has learned the code.
The red light in HomeLink should
begin f lashing. It will f lash slowly
at first, then rapidly.
When the red light f lashes rapidly,
release both buttons. HomeLink
should have learned the code from
the remote control.
Plug in the garage door opener
motor, then test the HomeLink
transceiver button by pushing it. It
should operate the garage door.
If the button does not work, repeat
this procedure to train it again. If it
still does not work, you may have a variable or rolling code garage
door opener. Test this by pressing
and holding the HomeLink
transceiver button you just trained.
If the red light blinks f or two
seconds,thenstayson,youhavea
rolling code garage door opener.
You may be able to verify this with
the manufacturer’s documentation.
Go to ‘‘Training With a Rolling
Code System.’’
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
5.
6.
7.
8.
Canadian Owners:T raining With a Rolling Code
System
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures164
01/09/28 19:51:19 31SZ3660_167

µµ
Itmaybehelpfultohavesomeone
assist you with this procedure.
Find the ‘‘Training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer. The
manufacturer’s documentation
may help. Press the Training button on the
garage door opener unit until the
light next to the button comes on,
then release it. The light may blink,
or come on and stay on. You then
have approximately 30 seconds to
complete the f ollowing steps.
Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
Press and hold the button on
HomeLink f or 3 4 seconds.
(The same button you trained with
the ‘‘Training HomeLink’’
procedure.)
Press and hold the HomeLink
button again f or 3 4 seconds.
This should turn of f the training
light on the garage door opener
unit. (Some systems may require
youtopressthebuttonuptothree
times.)
Press the HomeLink button again.
It should operate the garage door.
6.
2.
3.4.
5.
1.
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures165
T T
R
RA A I
INNI INNG G
B
BU UT TT
TO
ON N
01/09/28 19:51:29 31SZ3660_168

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red light
begins to f lash, then release the
buttons.
Youshoulderaseallthreecodes
bef ore selling the car.
Totrainanalreadyprogrammed
HomeLink button to operate a new
device:
Select the HomeLink button you
want to train.
Press and hold the HomeLink
button until the red light begins to
f lash slowly (approximately 20
seconds).
While continuing to hold the
HomeLink button, place the
remotecontrolforthedevice2to
5inchesfromHomeLink.
Press and hold the button on the
remote control. Hold both buttons
until the red light begins to f lash
rapidly. Release both buttons. HomeLink
should now be trained to operate
the device.
1.
3. 2.
4. 5.
Erasing Codes
Retraining a Button
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures166
01/09/28 19:51:42 31SZ3660_169

µµ
µ
µ
To cancel these retries, press the
Call Answer/End (DOT) button.
A microphone is located in the base
of therearviewmirrorsoyoucan
speak to the advisor without taking
your hands of f the steering wheel or
diverting your attention f rom the
road. The OnStar advisor’s voice
comes f rom the audio system’s
speakers. Use the volume control on
the audio system or on the steering
wheel to adjust the volume.
Press this button to contact an
OnStar advisor only if you have an
emergency situation. You will hear a
tone, f ollowed by the announcement,
‘‘Connecting to OnStar Emergency.’’
Your call is given highest priority. The advisor will ask about the nature
of the emergency, locate your
vehicle, and notif y the appropriate
emergency service agencies.
Press this ‘‘DOT’’ button to end a call
to the OnStar advisor, or to cancel
the call if you should press one of
the other buttons accidentally. If the
OnStar center should call you, press
this button to answer the call.
This button is also used to initiate
the Personal Calling and Virtual
Advisor services, if you have
subscribed.This light shows you the status of
the system.
The system is ready
for use.
Acallisin
progress.
There is a problem in
the system. Press the OnStar button
to contact an advisor. If the call
connects, the advisor will assist you
with verif ying the system’s operation.
If you are not able to contact an
advisor, take your vehicle to an
Acura dealer to have the system
diagnosed.
There is a problem
in the system with a call in progress.
If you press this button accidentally,
do not cancel the call. Wait until the
OnStar advisor answers, then explain
your mistake.
Emergency Button Call Answer/End ButtonSolid Green
Blinking Green
Solid Red
Blinking Red System Status L ight
OnStar System
Comf ort and Convenience Feat ures168
01/09/28 19:52:17 31SZ3660_171

µ
µ µ
µ
µ µ
µ
The OnStar system uses the Global
Positioning System (GPS) to locate
your vehicle whenever you place a
call. This allows the advisor to
quickly contact the nearest services
without requiring you to provide
detailed directions.
Contact
the OnStar advisor if you need
assistance with a problem (f lat tire,
out of f uel, etc.) while traveling. The
advisor will contact an appropriate
agency to come and assist you.
Contact an
OnStar advisor if you have an
emergency situation. The advisor
will contact the nearest emergency
services provider (ambulance, f ire
department, etc.) and advise them of
your situation. If you are ever in an
accident that causes the airbags to
deploy, the OnStar system
automatically places a call (provided
the OnStar system and your vehicle’s
electrical system are still intact). The
advisor will attempt to speak to you
to evaluate the situation, and contact
the nearest emergency services
provider.
The OnStar
advisor can help you if you are ever
in a minor accident by giving you a
list of inf ormation you should collect
at the accident scene.Complete,
detailed inf ormation will make it
easier to complete accident reports
and insurance claims.
By sending a signal to your
vehicle, the advisor can lock or
unlock your vehicle’s doors. This is
helpfulif youareawayfromyour vehicle and realize you f orgot to lock
the doors, or if you have locked the
keys in your vehicle. To get OnStar’s
assistance, call (888) 4-ONSTAR
(466-7827).
Using
GPS, OnStar can locate your vehicle
almost anywhere. If your vehicle is
ever stolen, contact OnStar at (888)
4-ONSTAR. The advisor will put you
in contact with the proper authorities,
and assist them with locating your
vehicle.
If you are unable to locate your
vehicleinalargeparkinglotor
parking structure, contact OnStar at
(888) 4-ONSTAR. The advisor will
remotely activate the exterior lights
and the horn, allowing you to locate
your vehicle.
Comf ort and Convenience Feat ures
OnStar System
Saf ety and Security Plan Features
Roadside Assistance
Emergency Services A utomatic Notif ication of A irbag
Deployment
A ccident A ssist
Remote Door L ocking/Unlocking
Stolen Vehicle T racking
Misplaced Vehicle Assistance
169
01/09/28 19:52:28 31SZ3660_172