2002 Acura RL audio

µµ
These two
controls adjust the strength of the
sound coming f rom each speaker.
The Balance control adjusts the side-
to-side strength, while the Fader
control adjusts the f ront-to-back
strength.
To adjust the fader, push on the
BASS/FADER control knob to get it
to pop out. Pull it out slightly f arther,
and adjust the f ront-to-back sound to
your liking. Push the knob back in
when you are done so you cannot
change the setting by accidentally
bumping it.
To adjust the balance, push on the
TREBLE/BALANCE control knob
to get it to pop out. Pull it out slightly
f arther, and adjust the side-to-side
sound to your liking. Push the knob
back in when you are done so you
cannot change the setting by
accidentally bumping it. Use these controls
to adjust the tone to your liking.
To adjust the Treble level, push on
the TREBLE/BALANCE control
knob to get it to pop out. Without
pulling it out f arther, turn the knob
to adjust the treble level. Push the
knob back in when you are done so
you cannot change the setting by
accidentally bumping it. To adjust the Bass level, push on the
BASS/FADER control knob to get it
to pop out. Without pulling it out
f arther, turn the knob to adjust the
bass level. Push the knob back in
when you are done so you cannot
change the setting by accidentally
bumping it.
Adjusting the Sound
Balance/Fader
Treble/Bass
Audio System
Comf ort and Convenience Feat ures132
B BAA S
SSS//F
FA A D
DE
ER
R
C
CO ON NTTR
RO OL L T
T
R
RE EB
BL LEE /
/B
BA A L
LAA N
NC CEE
C
CO ON NTTR
RO OL L
01/09/28 19:46:10 31SZ3660_135

ÛWhen the system reaches the end of
the tape, it will automatically reverse
direction and play the other side. If
you want to remove the cassette
f rom the drive, press the EJECT
button.
If you turn the system of f while a
tape is playing, either with the PWR/
VOL knob or by turning of f the
ignition, the cassette will remain in
the drive. When you turn the system
back on, the tape will begin playing
where it lef t of f .
To switch to the radio or CD
changer while listening to a tape,
press the AM/FM or CD/TAPE but-
ton. To change back to the cassette
player, press the CD/TAPE button.
Make sure the tape opening on the
cassette is facing to the right, then
insert the cassette most of the way
into the slot. The system will pull it
in the rest of the way, and begin to
play. The ignition switch must be in
ACCESSORY (I) or ON (II).
The tape direction indicator will light
to show you which side of the
cassette is playing. The indicates
thesideyouinsertedfacingupward
is now playing. If you want to play
the other side, press the PROG/
PLAY button.
Dolby noise reduction turns on when
you insert a cassette. If the tape was
not recorded with Dolby noise reduc-
tion, turn it of f by pressing the
button.
You can use the instrument panel
brightness control dial to adjust the il-
lumination of the audio system (see
page ). The audio system
illuminates when the parking lights
are on, even if the radio is turned of f .
For inf ormation, See page .
66
141
Audio System
Comf ort and Convenience Feat ures
Operating the Cassette Player
A udio System L ighting
Radio Frequencies and Reception
133
01/09/28 19:46:23 31SZ3660_136

µ
With a cassette playing, you can use
the FF, REW, TMS, or REPEAT
f unction to f ind a desired program.
Fast Forward and Re-
wind move the tape rapidly. To re-
wind the tape, push the REW button.
You will see REW in the display. To
fast forward the tape, push the FF
button. You will see FF displayed.
Press the PROG/PLAY button to
take the system out of rewind or fast
f orward. When the system reaches
the end of the tape, it reverses
direction and begins to play if in f ast
f orward, or it begins to play if in
rewind.
Audio System
Comf ort and Convenience Feat ures
T ape Search Functions
FF/REW
134
A A M
M /
/F
FM M B
BUUT TT
TO
ON N
T
T M
M S
SI
INND DI
ICCA A T
TO
OR R
D
D O
OL LBBY Y I
INND DI
ICCA A T
TO
OR R
E
EJ
JEE C
CT T
B
BU UT TT
TO
ON N
R
RE EP
PE
EA
A T
T
I
IN ND DI
ICCA A T
TO
OR R
R
RE EP
PE
EA
A T
T
B
BU UT TT
TO
ON N
T
T M
M S
S
B
BU UT TT
TO
ON N
D
D O
OL LBBY Y B
BUUT TT
TO
ON N
F
FA A S
STT F
FOOR RWWA AR
RDD
B
BU UT TT
TO
ON N
C
CD
D /
/T
T A
A P
PE
E B
BUUT TT
TO
ON N
R
RE
EW
WI INND D
B
BU UT TT
TO
ON N
P
P
R
RO OG G//P
P L
LAA Y
Y
B
BU UT TT
TO
ON N
T
T
A
A P
PE
E
D
D I
IRRE EC
CT TI
IOON N
I
IN ND DI
ICCA A T
TO
OR R
P
P
W
WR R//V
V O
OL L K
KNNO OBB
C
CA
A S
SSSEET
TT
TE
E S
SLLOOT T
01/09/28 19:46:32 31SZ3660_137

µTheTapeMusicSearch
Function allows you to f ind the begin-
ning of a song or passage. To acti-
vate TMS, press the TMS button.
You will see TMS displayed. To f ind
the beginning of the song or passage
currently playing, push the REW but-
ton. You will see REW f lashing in the
display as the tape rewinds. To f ind
the beginning of the next song, push
the FF button. You will see FF
flashing in the display as the tape
f ast f orwards. When the system
f inds the beginning of a song or pas-
sage, it goes back to PLAY mode.
Press the TMS button again to turn
it off.
CONT INUED
Audio System
Comf ort and Convenience Feat ures
TMS
135
P P W
WR R//V
V O
OL L K
KNNO OBB
T
T A
A P
PE
E
D
D I
IRRE EC
CT TI
IOON N
I
IN ND DI
ICCA A T
TO
OR R
R
RE EW
WI INND D
B
BU UT TT
TO
ON N E
E
J
JEE C
CT T
B
BU UT TT
TO
ON N
R
RE EP
PE
EA
A T
T
I
IN ND DI
ICCA A T
TO
OR R
R
RE EP
PE
EA
A T
T
B
BU UT TT
TO
ON N
F
FA A S
STT F
FOOR RWWA AR
RDD
B
BU UT TT
TO
ON N
C
CA
A S
SSSEET
TT
TE
E S
SLLOOT T
T
T M
M S
SI
INND DI
ICCA A T
TO
OR R
T
TM
M S
SB
BUUT TT
TO
ON N
01/09/28 19:46:40 31SZ3660_138

µThe Repeat f unction
continuously replays the current
song or passage. Press the REPEAT
button to activate it; you will see RPT
displayed as a reminder. When the
system reaches the end of the song
or passage currently playing, it will
automatically go into rewind.
When it senses the beginning of the
same song or passage, the system
returns to PLAY mode. It will
continue to repeat this same
program until you deactivate
REPEAT by pressing the button
again. The TMS and REPEAT f unctions
use silent periods on the tape to f ind
the end of a song or passage. These
f eatures may not work to your
satisfaction if there is almost no gap
between selections, a high noise
level between selections, or a silent
period in the middle of a selection.
Damaged cassettes can jam inside
the drive or cause other problems.
See page for information on
cassette care and protection.
A Compact Disc changer is standard
equipment. It holds up to six discs,
providing several hours of continu-
ous entertainment. You operate the
CD changer with the same controls
used f or the radio and cassette
player.
To load the CDs in the magazine and
load the magazine into the CD
changer, refer to page . Play only
standard round discs. Odd-shaped
CDs may jam in the drive or cause
other problems.
Pressing the REW or FF button also
turns of f REPEAT. Do not play discs with disc accessories such as protective seals
or rubbers. Using them may also
cause the audio system to
malf unction.159
148
Audio System
Comf ort and Convenience Feat ures
REPEAT
Caring f or CassettesOperating the CD Changer
136
01/09/28 19:46:51 31SZ3660_139

µ
CONT INUED
To operate the CD changer, the igni-
tion switch must be in ACCESSORY
(I) or ON (II).
SelecttheCDmodebypressingthe
CD/TAPE button. You will see ‘‘CD’’
in the display. The system will start
to play the first track of the first disc
in the magazine. You will see the
disc and track number displayed.
When that disc ends, the next disc in
the magazine is loaded and played.
Af ter the last disc f inishes, the
system returns to disc 1.
To select a dif f erent disc, press the
appropriate preset button (1 6). If
you select an empty slot in the
magazine, the changer will, af ter
f inding that slot empty, try to load
the CD in the next slot. This
continues until it f inds a CD to load
and play.
Audio System
Comf ort and Convenience Feat ures137
C CDD /
/T
T A
A P
PE
E B
BUUT TT
TO
ON N
P
P W
WR R//V
V O
OL L
K
KN NO OBB
A
A M
M /
/F
FM M
B
BU UT TT
TO
ON N
P
PR
RE ES
SE ET
T B
BUUT TT
TO
ON NSS A
A
U
UT TO
O
S
SE EL
LEE C
CT T
B
BU UT TT
TO
ON N
S
SE
EE
EK
K/ /S
SK KIIPP
B
BU UT TT
TO
ON NSS
R
RE
EP
PE
EA
A T
T
B
BU UT TT
TO
ON N
A
A
.
.SSE EL
LEE C
CT T I
INND DI
ICCA A T
TO
OR R
R
RE EP
PE
EA
A T
T I
INND DI
ICCA A T
TO
OR R
01/09/28 19:46:59 31SZ3660_140

µ´
´
µ µ
µ
You can use the SEEK/SKIP buttons
to select tracks within a disc. If you
push and release either side of the
SEEK/SKIP buttons ( or ), the
system will move to the beginning of
a track. Push the button to move
to the beginning of the next track,
and push the button to move to
the beginning of the current track.
If you push and hold the SEEK/
SKIP button, you will hear a beep
and the system will continue to move
across tracks. Release the button
when you think it has reached the de-
sired place on the disc. When you activate the
Repeat feature by pressing the
REPEAT button, the system continu-
ously replays the current track. You
will see RPT in the display as a
reminder. Press the REPEAT button
again to turn it off.
This feature,
when activated, plays the tracks on a
CD in random order, rather than in
the order they are recorded on the
CD. To activate Random Play, press
the A. SELECT button. You will see
A. SELECT in the display. The sys-
tem will then select and play tracks
randomly on the current disc. When
all tracks on that disc have been
played, the next disc is loaded and
played randomly. This continues un-
til you deactivate Random Play by
pressing A. SELECT again. To take the system out of CD mode,
press the AM/FM button or insert a
cassette in the player. If a tape is
already in the cassette player, press
the CD/TAPE button. When you
return to CD mode, play will contin-
ue at the same point that it left off.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or the ignition switch, play will
continue at the same point when you
turn it back on.
For inf ormation on how to handle
and protect compact discs, see page
.
153
Audio System
Comf ort and Convenience Feat ures
REPEAT
RANDOM PLAY
Protecting Compact Discs
138
01/09/28 19:47:09 31SZ3660_141

µ
µ
µ µ
´ ´ µ
You can use any of three methods to
f ind radio stations on the selected
band: TUNE, SEEK, or the Preset
buttons.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
The band and f requency that the ra-
dio was last tuned to is displayed. To
change bands, press the AM/FM but-
ton. On the FM band, ST will be dis-
played if the station is broadcasting
in stereo. ST will flash if you are driv-
inginanareawheretheradiosignal
is weak. Stereo reproduction on AM
is not available. The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pushing the PWR/
VOL knob or the AM/FM button.
Adjust the volume by turning the
knob. Use the TUNE bar to tune
the radio to a desired f requency.
Push and release the appropriate
side of the bar quickly. The
f requency numbers will change in
small increments.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, push
either side of the SEEK bar ( or ) until you hear a beep. Push the
bar on the side to scan up f rom
the current f requency, and on the
side to scan down. It stops when it
finds a station with a strong signal.
CONT INUED
Preset
Operating the Radio
TUNE
SEEK
Audio System
Comf ort and Convenience Feat ures
3.5 RL wit h Navigat ion Syst em
139
01/09/28 19:47:20 31SZ3660_142