2002 Acura CL clock

CONT INUED
The spark plugs in your car are a
special platinum-tipped design f or
longer lif e. The spark plugs should
be replaced according to the time
and distance recommendations in
the maintenance schedule.Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover on
the f ront cylinder bank by pulling
it straight up.
Clean up any dirt and oil that have
collected around the ignition coils.Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
1.
2. 3.
Replacement
Spark Plugs
Maint enance235
H H
O
OL LDD I
INNG G C
CLLIIPP I
IG
GN NIITT I
IOON N C
COOI ILL
C
CO
ON NNNEEC
CT TO
OR R
L
LO OC CKK
T
T A
A B
B

´
µ´
µ
Install the ignition coil. Reinstall
the hexagon socket head cap bolt.
Push the wire connector onto the
ignition coil. Make sure it locks in
place.
Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.
Spark Plug Gap:
Spark Plug Gap:
8.
9.
10.
11. NGK:
DENSO:
NGK:
DENSO:
Spark Plugs
Maint enance
Specif ications:
Premium model
T ype-S
237
0.04 in (1.1 mm)
0.04 in (1.1 mm) PZFR5F-11
PKJ16CR-L11
PZFR6F-11
PKJ20CR-L11
0
0.1 mm0
0.1 mm
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Reinstall the radiator reserve tank.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Open the hood.
If you need to change a bulb on
the driver’s side, remove the
radiator reserve tank.
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
3.
4. 5.
6.
7.
1.
2.
Lights
Maint enance255
B BU
UL LBB
T
T A
A B
B

Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the splash shield. Pull the
splash shield down.
Remove the socket by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.Put the splash shield in place.
Reinstall the three holding clips.
Lock each clip in place by pushing
on the center.
Insert the socket and turn it one-
quarter turn clockwise to lock it in
place. Turn on the headlights to test the
new bulb.
3.
4. 5.
6.
1.
2.
Lights
Maint enance
Replacing a Road Lamp Bulb
256
H H O
OL LDD I
INNG G C
CLLIIPP S
S

If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.To remove the f ront turn signal/
parking light bulb, push it in
slightly and turn it
counterclockwise. To remove the
side marker bulb, pull it straight
out of its socket.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Put the inner f ender cover in place.
Install the two holding clips. Lock
each clip in place by pushing on
the center.
1.
2.
3.
4.5.
6.
7.
8.
9.
Lights
Maint enance
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
257
H H
O
OL LDD I
INNG G
C
CL LIIPP S
S

Open the trunk.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
Remove the f astener on the edge
of the trunk opening by turning it
counterclockwise with a coin.
Unscrew the cargo net mounting
button. Pull the lining back. Determine which of the f our bulbs
is burned out: stop/taillight, stop/
tail/side marker light, back-up
light, or turn signal.
Remove the socket by turning it
one-quarter turn counterclockwise.
1.
3. 2.4.
5.
6.
7.
Replacing Rear Bulbs
Lights
Maint enance258
F FA
A S
STTE
EN
NE ER
R C
CA
A R
RGGO O N
NEET
T
M
M O
OUUNNTTI
INNG G
B
BU UT TT
TO
ON N

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.Reinstall the socket. Turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
Put the f astener in the hole on the
side of the trunk lining and push
on the center until it locks (the
center is f lush with the head).
Screw the cargo net mounting
button back into the hole.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb in the socket.
1.
2.
8.
9.
3.
4.
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance259

Loosen the f ive wheel nuts 1/2
turn with the wheel wrench.
Turn the jack’s end bracket
counterclockwise to loosen it, then
remove the jack.
The jack is behind a cover in the
right f ender. Remove the cover by
turning the handle counterclock-
wise, then pulling on the cover.
6.
7.8.
T aking Care of t he Unexpect ed
Changing a Flat T ire
276
W WHHE
EE
EL
L W
WR REEN
NC CHH
J
JA
A C
CKK