PRACTICAL ASPECTS OF YOUR VEHICLE
98
CHANGING A WHEEL
Park the vehicle on level, stable
ground which is not slippery.
Apply the handbrake, engage first
gear or reverse (position Pon the
automatic gearbox) and switch offthe ignition.
Chock the rear of the wheel withshim 2diagonally opposite the
wheel to be changed.
Tools for changing a wheel 1 - Wheelbrace fitted to the lining of the boot on the rear right side.
2 - Shim stored in the jack bag.
3 - Jack (in a bag secured by two straps,on the right-hand side of the boot).
4 - Tool for removing wheel bolt trims(located on the boot rear right innerpanel). Removing the wheel
Remove the wheel trim using the wheelbrace 1by pulling next to the valve.
Loosen the wheel bolts (for vehicles fitted with alloy wheels, remove the chrome wheel bolts first; see "Features of alloy wheels", following page).
Position the jack 3at one of the four locations Aunderneath the vehicle, as
close as possible to the wheel to be changed. Ensure that the entire surface ofthe jack base plate is in contact with the ground.
Extend the jack 3.
Remove the bolts and release the wheel.
07-10-2002
PRACTICAL ASPECTS OF YOUR VEHICLE99
Refitting the wheel
After positioning the wheel, pre-tighten the bolts using the wheelbrace 1.
Compress the jack 3and release it.
Fully tighten the bolts using the wheelbrace 1.
Replace the wheel trim, starting at the valve passage hole, and press on it using the palm of the hand.
Replace the shim and the jack in their bag, then store the tools in the boot.For your safety, always change the wheel:
Ð on level, stable and non- slippery ground,
Ð with the handbrake applied and the ignition switched off,
Ð with the first or reverse gear engaged (position Pfor the auto-
matic gearbox),
Ð with the vehicle chocked using a shim.
Never go underneath a vehicle which is supported only by a jack(use an axle stand) .
After changing the wheel:
Ð As soon as possible contact a PEUGEOT dealer to check that the wheel bolts are tight.
07-10-2002
07-10-2002
PRACTICAL INFORMATION103
Rear lights Release the top of the boot side trim. Unscrew the wing bolt inside the boot
using the wheelbrace if necessary. Disconnect the connector
A.
Release the light unit.Release spanner B from the bulb holder.
Unscrew nut Cusing spanner B and
removet the bulb holder. Change the faulty bulb.When refitting, stow spanner B on
support D and refit the light.
1. Amber direction indicators
PY 21 W.
2. Reversing lights P 21 W.
3. Brake lights/side lights P 21/5 W.Front fog lamps H1 55 W Press underneath the access flap to release it. Open the flap.
Turn the cover to remove it.Disconnect the bulb.Pinch both ends of the securing clip to release the bulb.
The "amber" bulbs must bereplaced by bulbs of identi-
cal specification and colour.
07-10-2002
PRACTICAL ASPECTS OF YOUR VEHICLE117
206 CC ACCESSORIES
For your PEUGEOT only use accessories and original parts approved by the manufacturer.
These accessories and parts are all adapted to your PEUGEOT, after being tested and approved for reliability and safety, which
PEUGEOT cannot guarantee for other products.
A wide choice of original accessories, approved by PEUGEOT, is available through the dealer network. They all carry the
PEUGEOT guarantee. Safety:
Anti-theft alarms, lift detection alarm, window engraving, wheel locks, signalling triangle, first aid kit, ...
Protection: Covers suitable for side air bags, carpets, boot storage tray, É
Communication: Telephone, satellite navigation system, CD changers, audio systems, speakers, audio trim, ...
Personalisation: Alloy wheels, trims, mud flaps, aluminium and wood panel trim, ...
Comfort: Centre armrest, can holder, CD or cassette storage, telephone console, anti-air swirl net, ....
Leisure: Towbar, roof bars , snow chains, ...
Children: Booster seats and child seats, Kiddy Isofix seat, ...
Maintenance products: Screenwash, interior and exterior maintenance and cleaning products.
